HOGGI CLEO Wheelchair Service Manual

Partnerschaft für mobile Kinder
CLEO
Service instructions
en
CLEO Service and maintenance instructions
1
Model identification & basic configuration
1.1 Model identification (label)______________________________________________________4
1.2 Basic configuration____________________________________________________________5
2
Overview CLEO
2.
Overview___________________________________________________________________ 6
3
Common information
3.1 Preface_ ___________________________________________________________________ 7
3.2 Application__________________________________________________________________ 8
3.3 Declaration of conformity_______________________________________________________ 8
3.4 Terms of warranty____________________________________________________________ 8
3.5 Customer service_ ___________________________________________________________ 8
3.6 Service and repairs _ _________________________________________________________ 9
3.7 Packing and shipping instructions________________________________________________ 9
4
Safety Instructions
4.1 Meaning of symbols_ ________________________________________________________ 10
4.2 Common safety instructions_ __________________________________________________ 10
5
Required tools and maintenance schedule
5.1 Required tools______________________________________________________________ 11
5.2 Maintenance schedule_ ____________________________________________________12-13
6
Seat settings
6.1 Seat height and Seat angle CLEO and CLEO Ti__________________________________14-18
6.2 Seat depth_________________________________________________________________ 18
6.3 Back height________________________________________________________________ 18
6.4 Active degree_ ___________________________________________________________19-20
6.5 Backrest angle______________________________________________________________ 20
6.6 Footrest angle and lower leg length_ __________________________________________20-21
7
Maintenance schedule
7.1 Frame and base plates_______________________________________________________ 21
7.2 Back base_________________________________________________________________ 22
7.3 Seat and back unit___________________________________________________________ 23
7.4 Braking system___________________________________________________________23-26
7.5 Push bar and handles, One hand push-handle_____________________________________ 26
7.6 Wheel fork holder_ __________________________________________________________ 27
7.7 Front wheels_______________________________________________________________ 27
7.8 Rear wheels_ ______________________________________________________________ 27
7.9 Push rims_ ________________________________________________________________ 28
7.10 Fender____________________________________________________________________ 28
7.11 Anti tip and tip assist_________________________________________________________ 29
7.12 Footrest hanger___________________________________________________________29-30
7.13 Seat and back cushion_ ______________________________________________________ 31
7.14 Spoke guards_ _____________________________________________________________ 31
7.15 Headrest________________________________________________________________31-32
7.16 Backrest extension_ _________________________________________________________ 32
7.17
7.18
7.19
7.20
7.21
Therapy tray__ _____________________________________________________________ 32
Tie down kit________________________________________________________________ 32
Abduction block_____________________________________________________________ 32
Belt fixations_ ______________________________________________________________ 33
Outdoor front end_ __________________________________________________________ 33
8
Operating life
8.
CLEO Operating life_ ________________________________________________________ 34
9
Specifications
9.
CLEO Specifications_________________________________________________________ 34
1 Model identification
1.1 Model identification (label)
(The label is attached to the axle tube)
Colour code
Article number
Size
Serial number
CE label
Classification / Product name
Date of manufacture
Maximum load / load capacity
Manufacturer
Place of manufacture
Year of manufacture
UDI Code
4
1.2 Basic configuration
- Rigid frame active wheelchair in aluminium construction,
powder-coated; seat depth grows with the user
- 3 frame sizes:
- Frame size 1: SW 24-30 cm in 2cm steps
- Frame size 2: SW 24-34 cm in 2cm steps
- Frame size 3: SW 26-34 cm in 2cm steps
- Convertible to other seat widths
- Front seat heights: 29 cm up to 46cm
- Seat angle: approx. 0,5° to 11,5°
- Footrest hanger 90° inclusive ABS-footrest
- Backrest angle: -10° up to +10°
- Seat- and back panel
- Clothes cover
- HOGGI light rear wheels inclusive push rims
(removable via quick-release axle)
- HOGGI light wheel locks
- Camber 6°, 9° or 12°
- Load capacity: 60 kg
5
CLEO Overview
6
3 Common Information
3.1 Preface
Thank you for selecting the CLEO wheechair. We have designed this high-quality product
to make your life safer and easier, and we’ve included this manual to help you use and
care for it.
Please read the following instructions to make sure you use this product as recommended.
If you have any further questions, or if you have any problems, please contact your healthcare provider.
We hope that CLEO meets your expectations.
We reserve technical modifications regarding the specified model in this manual. Before
using the wheechair the first time, this manual has to be read and understood by patient
and support personnel in oder to ensure a safe handling with the wheelchair.
Regular maintenance is important - it increases safety and prolongs the life of the product.
Every rehab product should be checked and serviced once a year.
However, it is recommended to check, readjust and, if necessary, service products with
a high frequency of use, with users in growth or users with a changing clinical picture at
6-month intervals.
Only original spare parts should be used for all service and maintenance work.
The service and maintenance work described here should only be carried out by trained specialist personnel and not by the user of the aid.
These service and maintenance instructions refer to the respective spare parts catalogs and
operating instructions of the products described. Please use all documents together.
Use the maintenance schedule (Chapter 4.2, Checklist to tick off) as a copy template.
Retain completed maintenance schedules and provide a copy to the customer.
CLEO User manual
CLEOSpare parts catalog
7
1910-0040-EN
1910-1013-EN
3.2 Application
CLEO wheelchair is designed solely for individual indoor and outdoor use by childern
and adolescents who are unable to walk or who have a walking impediment, and can be
operated by the patient or by another person.
Assistance may be required due to:
- Paralysis (paraplegia / tetraplegia or tetraparesis)
- Loss of limbs (dysmelia/lower limb amputation)
- Infantile/spastic cerebral palsy
- Spina Bifida
- Muscle and nerve disorders
- Osteogenesis Imperfecta
- Poliomyeliti
The CLEO wheelchair is able to be used for further service. For further service the product
has to be cleaned and sanitised efficiently. Afterwards the product has to be checked
concerning condition, wearout and damage by an authorised technician. All damaged and
inapropptiate parts need to be changed. Some components can be used again, e.g. Rear
wheels, steering wheels or push handles. Please see also the service manual for detailled
information.
3.3 Declaration of Conformity
HOGGI GmbH as manufacturer declares under sole responsibility that the CLEO active
wheelchair meets the general safety and performance requirements to Annex I of the
Regulation (EU) 2017/745 of the European Parliament and of the Council. Applicable
harmonized standards have been applied. CLEO meets the requirements of ISO 7176-8,
DIN EN ISO 12182 and DIN EN ISO 12183.
3.4 Terms of Warranty
Warranty applies only when the product is used according to the specified conditions
and for the intended purposes, following all manufacturer’s recommendations.The
manufacturer is not responsible for damages caused by components and spare parts
not approved by the manufacturer. See also § 8 of terms and conditions on:
www.hoggi.de
3.5 Customer service
Our customer service will be happy to answer any technical questions you may have.
Please refer to the last page for contact addresses and telephone numbers.
8
3.6 Service and repairs
Service and repairs on the CLEO wheelchair may only be carried out by your specialist
dealer. In case of problems, contact your responsible specialist dealer. In case of repairs,
you will only receive original spare parts there.
Spare parts and replacement units are available during the entire service life of the product, but only for a maximum of 2 years after the sale of the last product in this series.
The wheelchair is custom made for the first time user. Therefore, no replacement wheelchair is available in the initial configuration. In order to ensure a correct spare parts delivery the serial no. of your wheelchair is required.
We are happy to help you find a dealer near you.
You can reach us at: [email protected]
3.7 Packing and shipping instructions
If CLEO has to be sent back to the manufacturer for repair or exchange the product must
be thoroughly cleaned/disinfected beforehand and put in a hygienically safe condition.
Packaging is done by wrapping the product in a clean film, ideally with air cushions and
the subsequent use of a sufficiently large cardboard box, so that no transport damage can
occur.
9
4 Safety instructions
4.1 Meaning of symbols
Caution!
Warning of possible danger of accident and injury. Warning of possible technical
damage.
Information!
About use of product.
Information!
For service-personnel.
Attention!
Read manual before use!
4.2
Common safety instructions
For all maintenance and repair work, you should generally observe a few points:
Attention!
Familiarize yourself with the functions of the product. If you are not familiar with the
product, study the user manual before testing. If no user manuals are available, request
them from us. You can also download documents from our homepage at: www.hoggi.de
Attention!
Study the service and maintenance instructions before starting work.
Attention!
Use suitable tools (see page 4 ff.).
Attention!
Wear suitable clothing and, if necessary, gloves and protective goggles.
Attention!
Secure the product from tipping over or falling down, e.g. from the workbench.
Attention!
Clean / disinfect the product before starting the test. If necessary, observe the instructions
in the user manual and product-specific test instructions.
Note!
Screws and nuts with thread locking are used for a large number of screw connections.
If you have to open such screw connections, replace the respective nut or screw with
one with new thread locking. If new nuts or bolts with thread locking are not available,
use liquid thread locking compound with medium strength (e.g. Loctite 241 or Euro Lock
A24.20).
10
5 Required tools and maintenance schedule
5.1 Required tools
The following list shows the tools and utilities required for service.
Reversible ratchet and sockets
size 8-24
Torque wrench
Measuring ranges 5-50 Nm
Wrench
Size 6 - 24
Hexagon wrench
Gr. 3 - 6
Screwdriver
Blade width 2.5 3.5 and 5.5
Phillips screwdriver
Size 2
Plastic hammer
Hammer approx. 300 g
Carpet knife with sickle and
standard blade
Side cutter
Liquid thread locking
„medium strength
Riveting pliers for rivets up to
5 mm
11
5.2 Maintenance schedule
Pos.
Customer:
...............................................
CLEO
Maintenance schedule
for regular inspection
Active wheelchair
Check (Checklist to tick off )
Area
Serial number:
1.)
Function / Setting
(see instruction manual)
.......................................
2.)
none
damage / deformation
3.)
Screw connections
1. Basic product
1.1
Frame & base plates
- Active degree settings
- Seat depth/seat height/seat
angle
o
o
o
1.2
Back base
- Recline
- Active degree settings
o
o
o
1.3
Seat and back unit
-Backrest height, Seat unit settings
1.4
Braking system
- Brakes
1.5
Push bar / Push handles
- Height adjustment
One hand push-handle
o
o
o
o
o
o
- Angle adjustment of the push
handle
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
- Dismount
1.6
Wheel fork holder
- Swivelling the wheel forks
1.7
Front wheels
- Tires
- Air pressure
- Running behavior of the wheels
1.8
Rear wheels
- Tires
- Air pressure
- Running behavior of the wheels
- Camber
- Quick release
1.9
Push rim
- Mounting position
Do the settings on the wheelchair
meet the user‘s requirements?
o
Notes:
12
1.)
Function / Setting
(see instruction manual)
2.)
none
damage / deformation
3.)
Screw connections
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
2. Accessories
2.1
Fender
- Height adjustment
2.2
Anti tip and tip assist
- Anti tip
- Swivel away
- Angle adjustment
2.3
Footrest hanger
- Lower leg length
- Folding away the footrest
- Footrest lock
- Footrest angle
2.4
Seat / back cushion
- Cushion
2.5
Spoke guard
- Spoke guard
2.6
Headrests
- Height adjustment
- Angle adjustment
- Cushion
2.7
Back rest extension
- Height adjsutment
- Cushion
2.8
Therapy tray
- Clamping unit
2.9
Tie down kit
- Bracket
2.10
Abduction block
- Bracket
- Swivel mechanism
2.11
Belt fixings:
Lap belt, 4-point lap belt, ankle
hugger
- Closures
Do the settings of the accessoires
meet the user‘s requirements?
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Notes:
The maintenance was performed by: ..............................................................on: ......................................
13
6. Seat settings
6.1 Seat height & seat angle CLEO
The seat height and seat angle of CLEO are adjusted via the hole
matrix on the base plates.
The corresponding holes are shown below.
Support brackets can also be installed in 2 different positions
High(h) and Low(l).
This results in further possible seat heights.
Support bracket installation: high
Support bracket installation: low
The support brackets are screwed to the base plate with M6x20 panhead screws.
14
Depending on the holes in which the support brackets are screwed, different seat heights and seat angles can be
realised. This results in different seat heights and seat angles for the 3 frame sizes:
15
16
Seat height CLEO Ti
2
The seat height of the CLEO Ti is realised on the one hand by shifting
the seat unit in relation to the slots in the base plate and on the other
hand by shifting screws within the edge base itself.
Relocating the seat unit in relation to the base plates
1
1. Loosen the 4 nuts (1) and remove the pressure plate (2) on both
sides of the wheelchair. Keep these for reuse.
For height adjustment it is sufficient to dismantle only one base plate.
2. Loosen and remove the screw on the base plate with the rosette (2). Keep this for reuse.
Loosen and remove the 3 screws on the base plate with the camber
adapter (3). Keep them for reuse.
3
2
3. The base plate can now be removed.
4. To change the seat height, take the seat unit out of the slots and
insert it in the desired position.
The slots adjust the seat height by 2cm.
When reassembling the wheelchair, simply reverse the reverse order
Relocating the screw connections within the tilt base
The screw connections shown here are in the upper hole position. By
moving them, the seat height can be varied by 1 cm.
In combination with the adjustment of the seat base in the oblong holes,
this results in the various adjustment possibilities..
17
The screw connections shown here are in the lower hole position.
6.2 Seat depth
The seat depth is set with the installation position of the two support
brackets.
The seat plate does not have to be removed beforehand in most cases.
Loosen the marked screw connection on both sides of the base plate
and select the desired seat depth by moving the the angles. Then
tighten all the screw connections again.
Adjustment range 22 - 40 cm
Support angle installation for long seat depths:
Preferably use, in any case, if the front edge of the seat plate
overhangs the base plate or is to be positioned just behind its front
edge.
Support bracket installation for short seat depths:
If possible, only use from a seat plate position (short seat depths), if the
front nose of the support bracket does not project or only slightly the
front edge of the base plate.
6.3 Back height
The backrest height can be adjusted steplessly after loosening the
marked screw connections (on both sides) in the marked slotted holes.
To achieve particularly large back heights, the screws can also be
offset in the oblong holes.
The back height is measured at the horizontal area of the upper back
edge!
18
6.4 Active degree
The active degree describes the ratio of the position of the backrest
relative to the drive wheel axis. The further the backrest is set behind
the the drive wheel axle, the more active CLEO can be driven.
Conversely, a setting above, or in front of, the drive axle means a more
stable driving position.
Caution. Settings with a high degree of activity require
an experienced driver and the use of an anti-tippers!
Active degree adjustment CLEO
The active degreeis set via the installation position of the back plate on
the base plate. There are 3 different back positions to choose from.
The lower the value, the more passive the setting.
In addition, CLEO offers the choice of two different base plates.
Shown here variant „active“ with an adjustment range of 0 - 8 cm
Shown here is the „comfort“ version with an adjustment range of
-5 cm to 3 cm. The longer wheelbase provides a more stable riding position.
To move the back plate in relation to the base plates, the marked
screws on the left and right must be loosened.
For a larger range of adjustment, the screws must be taken out and
inserted into the next row of the hole matrix.
Active degree 0
ADHL = Active degree hole line
ADHL1 for active degree adjustment 0 to 2
ADHL2 for active degree adjustment 3 to 4
ADHL3 for active degree adjustment 5 to 8
19
Active degree 8
123
Active degree adjustment CLEO Ti
With CLEO Ti, the active degree is achieved by sliding the seat unit relative to the base plates in the respective slotted holes.
By loosening the screw connections to the outer pressure plate, an adjustment range of 8 cm can then be guaranteed.
6.5 Backrest angle
If CLEO is not equipped with the „angle-adjustable“ backrest, the backrest angle is adjusted by loosening the marked screw connection.
The adjustment range is 20° in total.
Back angle adjustment range 0° to -10°
Back angle adjustment range 0° to +10°
6.6 Footrest angle and lower leg length
The footrest angle is preset to 90°. The adjustment range is +- 10° (80°
- 100°).
The lower leg length is realised by moving the footrest bracket vertically
on the tubes of the footrest hanger.
After loosening the wing screws on the back, the appropriate length can
be adjusted.
Afterwards, retighten the screws securely!
20
After loosening the four marked screw connections on the footrest bracket, the footrest can be adjusted in depth.
This alters the location of the foot rest and, therefore, also the foot
rest angle. The further the footrest is pulled out to the front, the greater
the angle becomes. If the procedure is reversed, the angle decreases
accordingly.
7. Maintenance schedule
7.1 Frame & base plates
Functional test:
- Check for general damage or deformation to the frame structure or
base plate.
Check of the screw connections:
- Connection of lintel adapter and base plate
- If applicable, screw connection for anti tipper or tip assist
- Front connecting screw frame and base plate
Tilt unit CLEO Ti
Functional test:
- Checking the tilt release and the proper function
- Checking for general damage or non-functionality
of corresponding components
Check of the screw connections:
- Screw connections to the lateral pressure plate
- Connection of the seat plate support to the tilt skid
- Locking bolt pull for backrest adjustment
- Mounting and functionality of the release lever
21
7.2 Back base rigid
Functional test:
- Checking the appropriate seat settings
- Check for general damage in the area of the back base
Check of the screw connections:
- Connection between back base and base plate
Back base „angle adjustable“
Functional test:
- Checking the corresponding seat settings
- Check for general damage in the area of the backrest base
- Checking the adjustment mechanism (slide rail, clamping,
running with little play)
Check of the screw connections:
- Connection between back base and base plate
- Mounting of the slide rail on the back plate
- Mounting of the mechanism on the backrest bracket
- Function of the clamping lever
Back base CLEO-Ti
Additional inspection of the latch unit and the complete
latch bolt system.
22
7.3 Seat and back unit
Seat frame
Functional test:
- Installation position of the support bracket and thus correct seat adjus ment.
- Checking for general damage and correct holding of the
seat plate
Check of the screw connections:
- Connecting of the support brackets to the base plate
- Fastening the seat plate to the support brackets
- Riveting with existing seat cushion
Back plate
Functional test:
- Check for general damage and firm hold
- Checking the correct adjustment
Check of the screw connections:
- Fixing the back plate at the back and front to the back base
7.4 Braking system
Brake HOGGI light
Functional test:
- Brake closure
- Faultless operation
- Visible damage
23
Brake opened
Brake closed
Check of the screw connections:
- Fixing the brake to the brake holder
- Fastening the brake holder to the base plates
Integrated brake system
Consisting of:
- Fender with integrated brake system
- Brake cable
- Brake
24
Functional test:
- Operability of the brake lever and smooth glide
- Good brake closure and contact pressure of the brake bracket
- Correct positioning of the brake lever in relation to the wheel. 90° angle and 3-5 mm wheel protrusion
- Check for general damage in the area of the fender and the rubber grip
- Good brake closure and contact pressure of the brake bracket
- Correct positioning of the brake lever in relation to the wheel. 90° angle and 3-5 mm wheel protrusion
- Check for general damage in the area of the fender and the rubber grip
Check of the screw connections:
- Fastening the brake lever to the fender
- Fastening the brake bracket to the brake bracket holder
- Bowden cable correctly looped in the cable pulley
12
3
6
10
4
9
5
2
2
8
8
7
10
11
1
Drum brake
Functional test:
- Build-up of brake pressure (readjustment at adjusting screw)
- Checking the brake lever for general damage (locking lever, cracks)
- Checking the Bowden cable (kinks or cracks)
- Check the brake anchor and brake pads (contamination, wear)
25
Check of the screw connections:
- Connection brake anchor with adapter
- Connection of brake anchor adapter with base plate
- Bowden cable correctly hooked in
- Screw connection of the brake handle to the handle unit
7.5 Push bar and handles, One hand push handle
Push bar
Functional test:
- Attachment and removal
- Clamping
- Height adjustment
- Height adjustment of the upper part by means of ratchet joints
- Checking for general damage
Push handles
Functional test:
- Attachment and removal
- Clamping
- Height adjustment
- Straight alignment of the bars
- Checking for general damage
One hand push handle
Functional test:
- Attachment and removal
- Clamping
- Height adjustment
- Checking for general damage
Check of the screw connections:
- Fastening the handle holders to the base plate
- Fastening the cross tube for stabilisation - Fastening the clamp to the back base
26
7.6 Wheel fork holder
Functional test:
- Swivelling of the wheel fork
- Smooth running or fluttering -> Checking the alignment
- Check for general damage to the forks
Check of the screw connections:
- Screw connection of the wheel axle
- Bolting the steering fork axle to the frame
7.7 Front wheels
Functional test:
- Check for general damage
- Check of the tread or profile (cracks, heavy wear)
- Wheel curvature too worn (tread max. up to 5mm to edge of wheel)
- Contamination in the area of the wheel bearing or the axle
7.8 Rear wheels
Functional test:
- Check for general damage
- Checking the treads and air pressure
- Checking the locking
- Checking the running behaviour of the wheel, clearance, mechanics of
the axle
- Checking of the correct alignment of the camber adapter and its bolting
Adjustment of the quick-release axle:
- The axle should be fitted with a minimum of clearance. If too much
movement is possible, the front nut is closed slightly clockwise with a
19 mm open-ended spanner in a clockwise direction, while the rear axle
is secured with an 11 mm open-ended spanner
- If the wheel is too tight, proceed in reverse order
27
7.9 Push rim
Functional test: - Check for general damage
- Severe scratching and sharp edges
Checking the screw connections:
- Attachment of handrim to rim, also at correct distance
7.10 Fender
Standard fender
Functional test: - Check for general damage
- Screw connection to the base plate firmly tightened
Fender with integrated armrests
Functional test:
- Height adjustment and latching of the armrest
- Damage to the armrest cushion
- Damage to the release button
- Screw connection to base plate firmly tightened
- Armrest holder firmly screwed to wheel cover
Fender with integrated brake system and armrests
Functional test:
- Check for general damage
- Height adjustment and latching of the armrest
- Damage to the armrest cushion
- Damage to the release button
- Checking the brake unit (see 6.4 Brake system)
- Screw connection to base plate firmly tightened
- Armrest holder firmly screwed to wheel cover
28
7.11 Anti tip and tip assist
Anti tip
Functional test: - Check for general damage
- Correct positioning (beyond the wheel radius, 2-3 cm above the floor)
- Checking the swivel mechanism
- Checking the length adjustment
Tip assist
Functional test: - Check for general damage
- Good grip of the rubber cap
Check of the screw connections:
- Screw connection of the anti tipper or tip assist mounting bracket to the
base plate
- Screw connection of the anti tipper or the tip assist to the base plate.
7.12 Footrest hanger
Footrest hanger
Functional test:
- Check for general damage
- Distance to the seat plate
- Screw connection to the seat plate
Footrest hanger angle adjustable
Functional test:
- Check for general damage
- Swivel mechanism
- Clamping lever for angle adjustment
- Screw connection to the seat plate
29
Footrest hanger
Standard
Functional test:
- Check for general damage
- Swivel mechanism of the screwed-on footrest
- Correct adjustment of the foot angle
- Sliding of the holder on the tubes
With locking
Functional test:
- Check for general damage
- Swivel mechanism of the screwed-on footrest
- Correct adjustment of the foot angle
- Sliding of the holder on the tubes
- Locking bolt pull with locking latches, tension of the cable
Check of the screw connections:
- Wing screws for lower leg length adjustment
- Screw connection of the swivel mechanism
- Screw connection to the footboard with correct angle adjustment
Transfer support
Funktionsprüfung:
- Überprüfung auf generelle Beschädigung
- Stabiler Halt
- Überprüfung der Schraubverbindung
Footrest
All variants are to be considered equally
Check for general damage
30
7.13 Seat- and back cushion
Standard seat cushion
- Check for general damage (Velcro fastening, seams, holes or
strapped-through areas)
- Check for contamination
Seat cushion contoured
- Check for general damage (Velcro fastening, seams, holes or
strapped-through areas)
- Check for contamination
Back cushion
- Check for general damage (Velcro fastening, seams, holes or
strapped-through areas)
- Check for contamination
7.14 Spoke guards
Functional test:
- Check for general damage (cracks)
- Fastening clips complete or defective
- Spoke guards suitable for wheel (drum brake or normal)
7.15 Headrest
Headrest bracket
Functional test:
- Check for general damage
- Checking the clamping ability
- Checking the screw connection to the back plate
31
Headrest with upholstery
Functional test:
- Adjustment possibilities
- Check for general damage (wear, cracks, etc.)
- Clamping ability
Checking the screw connections:
- Attachment of pad to support
7.16 Backrest extension
Functional test:
- Check for general damage
- Height adjustment and clamping
Checking the screw connections:
- Connection of the bracket to the back plate
7.17 Therapy tray
Functional test:
- Attachability and fixation of the table on the armrests
- Checking for general damage (cracks, sharp edges, etc.)
Checking the screw connections:
- Connection of the table top to the clamping units
7.18 Tie down kit (ISO 7176-19)
Functional test:
- Check for general damage (deformation, sharp edges)
Check of the screw connections:
- Connection of the front and rear fuse to the base plate
7.19 Abduction block
Functional test:
- Check for general damage
- Pivoting and latching mechanism
- Removal
Check of the screw connections:
- Bracket abduction block to the seat panel
32
7.20 Belt fixations
Lap belt
Functional test:
- Check for general damage
- Check of the fastener
- Check of the screw connection of the bracket
4-point lap belt
Functional test:
- Check for general damage
- Check of the fastener
- Check of the screw connection of the bracket
Ankle hugger
Functional test:
- Check for general damage
- Check of the fastener
- Check of the screw connection of the bracket to the footrest
7.21 Outdoor front end
Functional test:
- Check for general damage
- Wear of the steering wheel
- Removal and installation
- Function of the locking pin hoist
- Wear of the release cable
Check the screw connections:
- Clamp and bracket of the steering wheel
- Screw connection of the crossbar
- Screwing of the latching mechanism
- Bolting of the bolt tension bracket
33
8. CLEO operating life:
The expected operating life of the CLEOs is 6 years, depending on the intensity of use, care as well
as maintenance. We recommend an annual inspection by the authorized specialist dealer.
In case of malfunctions or defects of the wheelchair, it must be immediately handed over to the medical supply
store or the specialist dealer.
9. Speficications
Frame size 1
Frame size 2
Frame size 3
Seat width
240 - 300 mm
240 - 340 mm
260 - 340 mm
Seat depth
220 - 360 mm
220 - 400 mm
240 - 400 mm
Back height
200, 250, 300, 350 mm 200, 250, 300, 350 mm 200, 250, 300, 350 mm Seat height* (front)
290 - 390 mm 320 - 420 mm
360 - 460 mm
Seat angle
approx. 0° up to 11°
approx. 0° up to 11°
approx. 0° up to 11°
Backrest angle
-10° up to +10°
-10° up to +10°
-10° up to +10°
Lower leg length
130 - 360 mm
130 - 360 mm
130 - 360 mm
Footrest angle
adjustable approx.
+/- 10°
adjustable approx.
+/- 10°
adjustable approx.
+/- 10°
Rear wheel diameter
20“
22“
24“
Front wheel diameter
4“, 5“, 5,5“
4“, 5“, 5,5“
4“, 5“, 5,5“
Camber
6°, 9°, 12°
6°, 9°, 12°
6°, 9°, 12°
User weight/
Maximum load*
60 kg
60 kg
60 kg
Weight ***
10,3 kg
10,8 kg
11,1 kg
Total length maximum / minimum 1030 mm / 915 mm
1090 mm / 935 mm
1090 mm / 965 mm
Total width maximum / minimum
660 mm / 515 mm
730 mm / 525 mm
750 mm / 555 mm
Height maximum / minimum
850 mm / 550 mm
880 / 580 mm
920 mm / 620 mm
Weight
(of the heaviest part)
7,3 kg
7,8 kg
8,1 kg
CAUTION!
*The seat height depends on the frame size, the wheel diameter and the wheel camber.
CAUTION!
**Accessories and add-on parts reduce the remaining load capacity for the occupant.
CAUTION!
*** The weight specifications refer to a CLEO in basic equipment and maximum seat width.
34
35
36
Eulerstraße 27 • 56235 Ransbach-Baumbach • Deutschland
Telefon: (+49) 2623 / 92 499-0
E-mail: [email protected] • www.hoggi.de
© by HOGGI GmbH_1910-0030-EN_04_2024
HOGGI GmbH
">