HOGGI CLEO Ti Wheelchair Service Manual
Hoggi CLEO Ti is a rigid frame active wheelchair made of aluminium. It is designed for children and adolescents who are unable to walk or who have a walking impediment and can be either self-propelled or pushed by another person. CLEO Ti offers a variety of adjustment options, including seat height, seat depth, backrest height, and backrest angle, allowing for customized fit. The wheelchair is also equipped with a tilting unit for ease of movement and features a 90° footrest that can be adjusted in angle and length.
PDF
Download
Document
Advertisement
Advertisement
Partnerschaft für mobile Kinder CLEO-Ti Service instructions en CLEO Ti Service and maintenance instructions 1 Model identification & basic configuration 1.1 Model identification (label)_____________________________________________________ 4 1.2 Basic configuration __________________________________________________________ 5 2 Overview CLEO-Ti 2. Overview __________________________________________________________________ 6 3 Common information 3.1 Preface ___________________________________________________________________ 7 3.2 Application_________________________________________________________________ 8 3.3 Declaration of conformity______________________________________________________ 8 3.4 Terms of warranty ___________________________________________________________ 8 3.5 Customer service ___________________________________________________________ 8 3.6 Service and repairs _________________________________________________________ 9 3.7 Packing and shipping instructions _______________________________________________ 9 4 Safety Instructions 4.1 Meaning of symbols ________________________________________________________ 10 4.2 Common safety instructions __________________________________________________ 10 5 Required tools and maintenance schedule 5.1 Required tools _____________________________________________________________ 11 5.2 Maintenance schedule ____________________________________________________12-13 6 Seat settings 6.1 Seat height _____________________________________________________________14-15 6.2 Seat depth ________________________________________________________________ 15 6.3 Back height _______________________________________________________________ 15 6.4 Active degree ___________________________________________________________15-16 6.5 Backrest angle_____________________________________________________________ 16 6.6 Seat angle ________________________________________________________________ 16 6.7 Footrest angle and lower leg length ____________________________________________ 17 7 Maintenance schedule 7.1 Frame and base plates ____________________________________________________17-18 7.2 Back base ________________________________________________________________ 18 7.3 Seat and back unit________________________________________________________18-19 7.4 Braking system __________________________________________________________19-21 7.5 Push bar and handles, One hand push-handle__________________________________21-22 7.6 Wheel fork holder __________________________________________________________ 22 7.7 Front wheels ______________________________________________________________ 22 7.8 Rear wheels ______________________________________________________________ 23 7.9 Push rims ________________________________________________________________ 23 7.10 Fender _________________________________________________________________23-24 7.11 Anti tip and tip assist ________________________________________________________ 24 7.12 Footrest hanger __________________________________________________________25-26 7.13 Seat and back cushion ______________________________________________________ 26 7.14 Spoke guards _____________________________________________________________ 27 7.15 7.16 7.17 7.18 7.19 7.20 7.21 Headrest _______________________________________________________________30-31 Backrest extension _________________________________________________________ 31 Therapy tray ______________________________________________________________ 27 Tie down kit _______________________________________________________________ 28 Abduction block ____________________________________________________________ 28 Belt fixations ______________________________________________________________ 28 Outdoor front end __________________________________________________________ 29 8 Operating life 8. CLEO-Ti Operating life ______________________________________________________ 30 9 Specifications 9. CLEO-Ti Specifications ______________________________________________________ 30 1 Model identification 1.1 Model identification (label) (The label is attached to the axle tube) Colour code Article number 327X-00SB-XXX CLEO 2021/05/07 Aktivrollstuhl Gr. X 2021178999 Hoggi GmbH Eulerstr. 27 56235 Ransbach-Baumbach MADE IN GERMANY Size Serial number max. load (01)04047349096062(21)202178999 60kg CE label 327X-00SB-XXX Classification / Product name CLEO 2021/05/07 Aktivrollstuhl Gr. X 2021178999 Hoggi GmbH Eulerstr. 27 56235 Ransbach-Baumbach MADE IN GERMANY Date of manufacture max. load (01)04047349096062(21)202178999 60kg Maximum load / load capacity 327X-00SB-XXX CLEO Manufacturer Place of manufacture 2021/05/07 Aktivrollstuhl Gr. X 2021178999 Hoggi GmbH Eulerstr. 27 56235 Ransbach-Baumbach MADE IN GERMANY Year of manufacture UDI Code max. load (01)04047349096062(21)202178999 60kg 4 1.2 Basic configuration - Rigid frame active wheelchair in aluminium construction, powder-coated; seat depth grows with the user - 3 frame sizes: - Frame size 1: SW 24-30 cm in 2cm steps - Frame size 2: SW 24-34 cm in 2cm steps - Frame size 3: SW 26-34 cm in 2cm steps - Convertible to other seat widths - Front seat heights: 38 cm up to 48cm - Seat angle: approx. -5° to 45° - Footrest hanger 90° inclusive ABS-footrest - Backrest angle: -5° bis 35° - Seat- and back panel - Clothes cover - HOGGI light rear wheels inclusive push rims (removable via quick-release axle) - HOGGI light wheel locks - Camber 6°, 9° or 12° - Load capacity: 60 kg 5 CLEO-Ti Übersicht 1 2 3 4 5 6 1. Back base 2. Seat unit 3. Rear wheels 4. Footrest hanger 5. Base plates 6. Front wheels 6 3 Common Information 3.1 Preface Thank you for selecting the CLEO Ti wheechair. We have designed this high-quality product to make your life safer and easier, and we’ve included this manual to help you use and care for it. Please read the following instructions to make sure you use this product as recommended. If you have any further questions, or if you have any problems, please contact your healthcare provider. We hope that CLEO Ti meets your expectations. We reserve technical modifications regarding the specified model in this manual. Before using the wheechair the first time, this manual has to be read and understood by patient and support personnel in oder to ensure a safe handling with the wheelchair. Regular maintenance is important - it increases safety and prolongs the life of the product. Every rehab product should be checked and serviced once a year. However, it is recommended to check, readjust and, if necessary, service products with a high frequency of use, with users in growth or users with a changing clinical picture at 6-month intervals. Only original spare parts should be used for all service and maintenance work. The service and maintenance work described here should only be carried out by trained specialist personnel and not by the user of the aid. These service and maintenance instructions refer to the respective spare parts catalogs and operating instructions of the products described. Please use all documents together. Use the maintenance schedule (Chapter 5.2, Checklist to tick off) as a copy template. Retain completed maintenance schedules and provide a copy to the customer. CLEO Ti User manual 1910-0051-EN CLEO Ti Spare parts catalog 1910-1013-EN 7 3.2 Application CLEO Ti wheelchair is designed solely for individual indoor and outdoor use by childern and adolescents who are unable to walk or who have a walking impediment, and can be operated by the patient or by another person. Assistance may be required due to: - Paralysis (paraplegia / tetraplegia or tetraparesis) - Loss of limbs (dysmelia/lower limb amputation) - Infantile/spastic cerebral palsy - Spina Bifida - Muscle and nerve disorders - Osteogenesis Imperfecta - Poliomyeliti The CLEO Ti wheelchair is able to be used for further service. For further service the product has to be cleaned and sanitised efficiently. Afterwards the product has to be checked concerning condition, wearout and damage by an authorised technician. All damaged and inapropptiate parts need to be changed. Some components can be used again, e.g. Rear wheels, steering wheels or push handles. Please see also the service manual for detailled information. 3.3 Declaration of Conformity HOGGI GmbH as manufacturer declares under sole responsibility that the CLEO Ti active wheelchair meets the general safety and performance requirements to Annex I of the Regulation (EU) 2017/745 of the European Parliament and of the Council. Applicable harmonized standards have been applied. CLEO Ti meets the requirements of ISO 7176-8, DIN EN ISO 12182 and DIN EN ISO 12183. 3.4 Terms of Warranty Warranty applies only when the product is used according to the specified conditions and for the intended purposes, following all manufacturer’s recommendations.The manufacturer is not responsible for damages caused by components and spare parts not approved by the manufacturer. See also § 8 of terms and conditions on: www.hoggi.de 3.5 Customer service Our customer service will be happy to answer any technical questions you may have. Please refer to the last page for contact addresses and telephone numbers. 8 3.6 Service and repairs Service and repairs on the CLEO Ti wheelchair may only be carried out by your specialist dealer. In case of problems, contact your responsible specialist dealer. In case of repairs, you will only receive original spare parts there. Spare parts and replacement units are available during the entire service life of the product, but only for a maximum of 2 years after the sale of the last product in this series. The wheelchair is custom made for the first time user. Therefore, no replacement wheelchair is available in the initial configuration. In order to ensure a correct spare parts delivery the serial no. of your wheelchair is required. We are happy to help you find a dealer near you. You can reach us at: [email protected] 3.7 Packing and shipping instructions If CLEO Ti has to be sent back to the manufacturer for repair or exchange the product must be thoroughly cleaned/disinfected beforehand and put in a hygienically safe condition. Packaging is done by wrapping the product in a clean film, ideally with air cushions and the subsequent use of a sufficiently large cardboard box, so that no transport damage can occur. 9 4 Safety instructions 4.1 Meaning of symbols Caution! Warning of possible danger of accident and injury. Warning of possible technical damage. Information! About use of product. Information! For service-personnel. Attention! Read manual before use! 4.2 Common safety instructions For all maintenance and repair work, you should generally observe a few points: Attention! Familiarize yourself with the functions of the product. If you are not familiar with the product, study the user manual before testing. If no user manuals are available, request them from us. You can also download documents from our homepage at: www.hoggi.de Attention! Study the service and maintenance instructions before starting work. Attention! Use suitable tools (see page 4 ff.). Attention! Wear suitable clothing and, if necessary, gloves and protective goggles. Attention! Secure the product from tipping over or falling down, e.g. from the workbench. Attention! Clean / disinfect the product before starting the test. If necessary, observe the instructions in the user manual and product-specific test instructions. Note! Screws and nuts with thread locking are used for a large number of screw connections. If you have to open such screw connections, replace the respective nut or screw with one with new thread locking. If new nuts or bolts with thread locking are not available, use liquid thread locking compound with medium strength (e.g. Loctite 241 or Euro Lock A24.20). 10 5 Required tools and maintenance schedule 5.1 Required tools The following list shows the tools and utilities required for service. Reversible ratchet and sockets size 8-24 Torque wrench Measuring ranges 5-50 Nm Wrench Size 6 - 24 Hexagon wrench Gr. 3 - 6 Screwdriver Blade width 2.5 3.5 and 5.5 Phillips screwdriver Size 2 Plastic hammer Hammer approx. 300 g Carpet knife with sickle and standard blade Side cutter Liquid thread locking „medium strength Riveting pliers for rivets up to 5 mm 11 5.2 Maintenance schedule Maintenance schedule for regular inspection Pos. Customer: ............................................... CLEO-Ti Active wheelchair Check (Checklist to tick off ) Area Serial number: 1.) Function / Setting (see instruction manual) ....................................... 2.) none damage / deformation 3.) Screw connections 1. Basic product 1.1 Frame & base plates - Active degree settings - Seat depth/seat height/seat angle o o o 1.2 Back base - Recline - Active degree settings o o o 1.3 Seat and back unit --Backrest height, Seat unit settings o o o 1.4 Braking system - Brakes 1.5 Push bar / Push handles - Height adjustment One hand push-handle o o o o - Angle adjustment of the push handle o o o o 1.6 Wheel fork holder - Swivelling the wheel forks 1.7 Front wheels - Tires o o o o o o o o o o o o o o o o o o - Dismount - Air pressure - Running behavior of the wheels 1.8 Rear wheels - Tires - Air pressure - Running behavior of the wheels - Camber - Quick release 1.9 Push rim - Mounting position Do the settings on the wheelchair meet the user‘s requirements? o Notes: 12 1.) Function / Setting (see instruction manual) 2.) none damage / deformation 3.) Screw connections o o o o o o o o o o o o o o o o o o o o o o o o o o 2. Accessories 2.1 Fender - Height adjustment 2.2 Anti tip and tip assist - Anti tip - Swivel away - Angle adjustment 2.3 Footrest hanger - Lower leg length - Folding away the footrest - Footrest lock - Footrest angle 2.4 Seat / back cushion - Cushion 2.5 Spoke guards - Spoke guards 2.6 Headrests - Height adjustment - Angle adjustment - Cushion 2.7 Back rest extension - Height adjsutment - Cushion 2.8 Therapy tray - Clamping unit 2.9 Tie down kit - Bracket 2.10 Abduction block - Bracket - Swivel mechanism 2.11 Belt fixings: Lap belt, 4-point lap belt, ankle hugger - Closures Do the settings of the accessoires meet the user‘s requirements? o o o o o o o o o o o o o o o o o o o o Notes: The maintenance was performed by:.............................................................. on: ...................................... 13 Seite 1 von 1 6.1 Seat height The seat height of the CLEO Ti is adjusted by moving the seat unit in relation to the slots in the base plate on the one hand, and on the other hand by moving screws within the tilt base itself. 2 Relocating the seat unit in relation to the base plates 1 Loosen the 4 nuts (1) and remove the pressure plate (2) on both sides of the wheelchair. Keep them for reuse. Seite 1 von 1 For height adjustment it is sufficient to dismantle only one base plate! 2. Loosen and remove the screw on the base plate with the rosette (2). Keep this for reuse. Loosen and remove the 3 screws on the base plate with the camber adapter (3). Keep them for reuse. 3 Seite 1 von 1 2 3. The base plate can now be removed file:///H:/6-Marketing/Dokumentation_2018/Montageanleitung/Montageanleitung_CL... 23.09.2019 Seite 1 von 1 file:///H:/6-Marketing/Dokumentation_2018/Montageanleitung/Montageanleitung_CL... 23.09.2019 4. To change the seat height, remove the seat unit from the slots and insert it in the desired position. The slots adjust the seat height by 2cm When reassembling the wheelchair, simply follow the reverse reverse order Relocating the screw connections within the tilt base file:///H:/6-Marketing/Dokumentation_2018/Montageanleitung/Montageanleitung_CL... 23.09.2019 The screw connections shown here are in the upper hole position. By moving them, the seat height can be varied by 1 cm. In combination with moving the seat base in the slotted holes, this results in the various adjustment possibilities. 14 The screw connections shown here are in the lower hole position. 6.2 Seat depth The seat depth is set with the installation position of the two support brackets. The seat plate does not have to be removed beforehand in most cases. Loosen the marked screw connection on both sides of the base plate and select the desired seat depth by moving the the angles. Then tighten all the screw connections again. Adjustment range 22 - 40 cm Support angle installation for long seat depths: Preferably use, in any case, if the front edge of the seat plate overhangs the base plate or is to be positioned just behind its front edge. Support bracket installation for short seat depths: If possible, only use from a seat plate position (short seat depths), if the front nose of the support bracket does not project or only slightly the front edge of the base plate. 6.3 Back height The back height can be adjusted after loosening the marked screw connections (on both sides). Sometimes the screws have to be inserted in new hole positions. 6.4 Active degree The active degree describes the ratio of the position of the backrest relative to the drive wheel axis. The further the backrest is set behind the the drive wheel axle, the more active CLEO Ti can be driven. Conversely, a setting above, or in front of, the drive axle means a more stable driving position. Aktivgrad Caution. Settings with a high degree of activity require an experienced driver and the use of an anti-tippers! 15 With CLEO Ti, the active degree is achieved by sliding the seat unit relative to the base plates in the respective slotted holes. By loosening the screw connections to the outer pressure plate, an adjustment range of 8 cm can then be guaranteed. 6.5 Backrest angle The backrest angle of CLEO-Ti can be adjusted between -5° and +35°. The backrest angle is adjusted by means of a locking bolt on the back. 6.6 Seat angle The seat angle of the CLEO-Ti can be adjusted between -10° and +45°. The operation is done via a release lever on the crossbar of the back support. 16 6.7 Footrest angle and lower leg length The footrest angle is preset to 90°. The adjustment range is +- 10° (80° - 100°). The lower leg length is realised by moving the footrest bracket vertically on the tubes of the footrest hanger. After loosening the wing screws on the back, the appropriate length can be adjusted. Afterwards, retighten the screws securely! After loosening the four marked screw connections on the footrest bracket, the footrest can be adjusted in depth. This alters the location of the foot rest and, therefore, also the foot rest angle. The further the footrest is pulled out to the front, the greater the angle becomes. If the procedure is reversed, the angle decreases accordingly. 7. Maintenance schedule 7.1 Frame & base plates Functional test: - Check for general damage or deformation to the frame structure or base plate. Check of the screw connections: - Connection of lintel adapter and base plate - If applicable, screw connection for anti tipper or tip assist - Front connecting screw frame and base plate Tilt unit Functional test: - Checking the tilt release and the proper function - Checking for general damage or non-functionality of corresponding components 17 Check of the screw connections: - Screw connections to the lateral pressure plate - Connection of the seat plate support to the tilt skid - Locking bolt pull for backrest adjustment - Mounting and functionality of the release lever ls 7.2 Back base Functional test: - Checking the corresponding seat settings - Check for general damage in the area of the backrest base - Checking the adjustment mechanism (slide rail, clamping, running with little play) 7.3 Seat and back unit Seat frame Functional test: - Installation position of the support bracket and thus correct seat adjusment. - Checking for general damage and correct holding of the seat panel Check of the screw connections: - Connecting of the support brackets to the base plate - Fastening the seat panel to the support brackets - Riveting with existing seat cushion Back panel Functional test: - Check for general damage and firm hold - Checking the correct adjustment 18 Check of the screw connections: - Fixing the back panel at the back and front to the back base 7.4 Braking system Brake HOGGI light Functional test: - Brake closure - Faultless operation - Visible damage Brake opened Brake closed Check of the screw connections: - Fixing the brake to the brake holder - Fastening the brake holder to the base plates 19 Integrated brake system Consisting of: - Fender with integrated brake system - Brake cable - Brake Functional test: - Operability of the brake lever and smooth glide - Good brake closure and contact pressure of the brake bracket - Correct positioning of the brake lever in relation to the wheel. 90° angle and 3-5 mm wheel protrusion - Check for general damage in the area of the fender and the rubber grip - Good brake closure and contact pressure of the brake bracket - Correct positioning of the brake lever in relation to the wheel. 90° angle and 3-5 mm wheel protrusion - Check for general damage in the area of the fender and the rubber grip Check of the screw connections: - Fastening the brake lever to the fender 20 - Fastening the brake bracket to the brake bracket holder - Bowden cable correctly looped in the cable pulley 12 3 6 10 4 9 5 2 2 8 8 7 10 11 1 Drum brake Functional test: - Build-up of brake pressure (readjustment at adjusting screw) - Checking the brake lever for general damage (locking lever, cracks) - Checking the Bowden cable (kinks or cracks) - Check the brake anchor and brake pads (contamination, wear) Check of the screw connections: - Connection brake anchor with adapter - Connection of brake anchor adapter with base plate - Bowden cable correctly hooked in - Screw connection of the brake handle to the handle unit 7.5 Push bar, One hand push handle Push bar Functional test: - Attachment and removal - Clamping - Height adjustment - Height adjustment of the upper part by means of ratchet joints - Checking for general damage One hand push handle Functional test: - Attachment and removal - Clamping - Height adjustment - Angle adjustment through cross tube attachment - Checking for general damage 21 The central push handle can generally be aligned in 3 different positions, depending on whether iit is to be aligned further forward or backward. CLEO Ti is aligned in the centre position ex works. By moving the screw connection to another hole position, the angle of the handle holder and thus of the entire handle changes accordingly. The central push handle holder is attached using the holes in the cross strut. 7.6 Wheel fork holder Functional test: - Swivelling of the wheel fork - Smooth running or fluttering -> Checking the alignment - Check for general damage to the forks 9 Check of the screw connections: POS-NR. BENENNUNG 10 1 1 8 3 4 6 BESCHREIBUNG Wheel fork 126,5x45x10 / 3x holes / d=12 Lenkgabelachse - Screw connection2of the wheel axle 1205-0007-2 1051-0012 3 fork - Bolting the steering axle to the frame 2 3 1281-0016 7 MENGE 1 1 2 1 1052-0008 Federscheibe B12 verz DIN/ISO 137 B12 Sechskantmutter verz DIN/ISO 4035 BM12 Federscheibe B8 verz DIN/ISO 137 B8 7 1205-0009 Radachse L 54 1 8 1029-6001 9 1042-0008 10 1051-0008 4 1052-0012 5 1043-0012 6 1 1 1 Sechskantmutter selbstsichernd verz DIN/ISO 985 M8 Scheibe A8,4 verz DIN/ISO 125 A8,4 1 1 5 7.7 Front wheels Functional test: - Check for general damage - Check of the tread or profile (cracks, heavy wear) - Wheel curvature too worn (tread max. up to 5mm to edge of wheel) - Contamination in the area of the wheel bearing or the axle 22 7.8 Rear wheels Functional test: - Check for general damage - Checking the treads and air pressure - Checking the locking - Checking the running behaviour of the wheel, clearance, mechanics of the axle - Checking of the correct alignment of the camber adapter and its bolting Adjustment of the quick-release axle: - The axle should be fitted with a minimum of clearance. If too much movement is possible, the front nut is closed slightly clockwise with a 19 mm open-ended spanner in a clockwise direction, while the rear axle is secured with an 11 mm open-ended spanner - If the wheel is too tight, proceed in reverse order 7.9 Push rim Functional test: - Check for general damage - Severe scratching and sharp edges Checking the screw connections: - Attachment of handrim to rim, also at correct distance 7.10 Fender Standard fender Functional test: - Check for general damage - Screw connection to the base plate firmly tightened Fender with integrated armrests Functional test: - Height adjustment and latching of the armrest - Damage to the armrest cushion - Damage to the release button - Screw connection to base plate firmly tightened - Armrest holder firmly screwed to wheel cover 23 Fender with integrated brake system and armrests Functional test: - Check for general damage - Height adjustment and latching of the armrest - Damage to the armrest cushion - Damage to the release button - Checking the brake unit (see 6.4 Brake system) - Screw connection to base plate firmly tightened - Armrest holder firmly screwed to wheel cover 7.11 Anti tip and tip assist Anti tip Functional test: - Check for general damage - Correct positioning (beyond the wheel radius, 2-3 cm above the floor) - Checking the swivel mechanism - Checking the length adjustment Tip assist Functional test: - Check for general damage - Good grip of the rubber cap Check of the screw connections: - Screw connection of the anti tipper or tip assist mounting bracket to the base plate - Screw connection of the anti tipper or the tip assist to the base plate. 24 7.12 Footrest hanger Footrest hanger Functional test: - Check for general damage - Distance to the seat plate - Screw connection to the seat plate Footrest hanger angle adjustable Functional test: - Check for general damage - Swivel mechanism - Clamping lever for angle adjustment - Screw connection to the seat plate POS-NR. BENENNUNG BESCHREIBUNG MENGE 1 Y X 1 2 3201-2520 8 3 4 6 7 2 2 3 1052-0008 4 3201-2530 Lagerbuchse 2 5 3240-2911 Fußbrettträger 1 6 1051-0006 Scheibe A6,4 verz DIN/ISO 125 A6,4 2 Functional test:7 1029-0640 Linsenschraube m ISK verz DIN/ISO 7380 M6x40 2 Footrest hanger 9 1 2 Federscheibe B8 verz DIN/ISO 137 B8 Standard L-Flanschmutter L-769 verz - Check for general damage 8 1049-0052 22x14xM6x8,5 - Swivel mechanism of the screwed-on footrest Flügelschraube PA schwarz 9 - Correct adjustment of1123-0612 the foot angle M6x12 - Sliding of the holder on the tubes 10 5 11 12 2 10 1024-0616 Senkschraube m ISK verz DIN/ISO 7991 M6x16 4 11 1055-0006 Scheibe verz DIN/ISO 9021 A6,4 4 12 1042-0006 Sechskantmutter selbstsichernd verz DIN/ISO 985 M6 4 With locking 11 2 Functional test: 10 5 4 8 1 9 7 2 6 3 - Check for general damage - Swivel mechanism of the screwed-on footrest - Correct adjustment of the foot angle - Sliding of the holder on the tubes - Locking bolt pull with locking latches, tension of the cable Check of the screw connections: - Wing screws for lower leg length adjustment - Screw connection of the swivel mechanism - Screw connection to the footboard with correct angle adjustment 25 Transfer support Funktionsprüfung: - Überprüfung auf generelle Beschädigung - Stabiler Halt - Überprüfung der Schraubverbindung Footrest All variants are to be considered equally Check for general damage 7.13 Seat- and back cushion Standard seat cushion - Check for general damage (Velcro fastening, seams, holes or strapped-through areas) - Check for contamination Seat cushion contoured - Check for general damage (Velcro fastening, seams, holes or strapped-through areas) - Check for contamination Back cushion - Check for general damage (Velcro fastening, seams, holes or strapped-through areas) - Check for contamination 26 7.14 Spoke guards Functional test: - Check for general damage (cracks) - Fastening clips complete or defective - Spoke guards suitable for wheel (drum brake or normal) 7.15 Headrest Headrest bracket Functional test: - Check for general damage - Checking the clamping ability - Checking the screw connection to the back plate Headrest with upholstery Functional test: - Adjustment possibilities - Check for general damage (wear, cracks, etc.) - Clamping ability Checking the screw connections: - Attachment of pad to support 7.16 Backrest extension Functional test: - Check for general damage - Height adjustment and clamping Checking the screw connections: - Connection of the bracket to the back plate 7.17 Therapy tray Functional test: - Attachability and fixation of the table on the armrests - Checking for general damage (cracks, sharp edges, etc.) Checking the screw connections: - Connection of the table top to the clamping units 27 7.18 Tie down kit (ISO 7176-19) Functional test: - Check for general damage (deformation, sharp edges) Check of the screw connections: - Connection of the front and rear fuse to the base plate 7.19 Abduction block Functional test: - Check for general damage - Pivoting and latching mechanism - Removal Check of the screw connections: - Bracket abduction block to the seat panel 7.20 Belt fixations Lap belt Functional test: - Check for general damage - Check of the fastener - Check of the screw connection of the bracket 4-point lap belt Functional test: - Check for general damage - Check of the fastener - Check of the screw connection of the bracket Ankle hugger Functional test: - Check for general damage - Check of the fastener - Check of the screw connection of the bracket to the footrest 28 7.21 Outdoor front end Functional test: - Check for general damage - Wear of the steering wheel - Removal and installation - Function of the locking pin hoist - Wear of the release cable Check the screw connections: 11 6 7 11 8 5 9 4 3 10 2 11 12 - Clamp and bracket of the steering wheel - Screw connection of the crossbar - Screwing of the latching mechanism - Bolting of the bolt tension bracket 1 29 8. CLEO-Ti operating life: The expected operating life of the CLEO-Ti is 5 years, depending on the intensity of use, care as well as maintenance. We recommend an annual inspection by the authorized specialist dealer. In case of malfunctions or defects of the wheelchair, it must be immediately handed over to the medical supply store or the specialist dealer. 9. Speficications Frame size 1 Frame size 2 Frame size 3 Seat width 240 - 300 mm 240 - 340 mm 260 - 340 mm Seat depth 220 - 360 mm 220 - 400 mm 240 - 400 mm Back height 200, 250, 300, 350, 400 mm 200, 250, 300, 350, 400 mm 200, 250, 300, 350,400 mm Seat height* (front) 380 - 410 mm 405 - 435 mm 450 - 480 mm Seat angle -5° up to 45° -5° up to 45° -5° up to 45° Backrest angle -5 up to 35° -5 up to 35° -5 up to 35° Lower leg length 130 - 360 mm 130 - 360 mm 130 - 360 mm Footrest angle adjustable approx. +/10° adjustable approx. +/10° adjustable approx. +/10° Rear wheel diameter 20“ 22“ 24“ Front wheel diameter 4“, 5“, 5,5“ 4“, 5“, 5,5“ 4“, 5“, 5,5“ Camber 6°, 9°, 12° 6°, 9°, 12° 6°, 9°, 12° User weight/ Maximum load** 60 kg 60 kg 60 kg Total length maximum / minimum 1030 mm / 915 mm 1090 mm / 935 mm 1090 mm / 965 mm Total width maximum / minimum 660 mm / 515 mm 730 mm / 525 mm 750 mm / 555 mm Height maximum / minimum 880 / 580 mm 920 mm / 620 mm 850 mm / 550 mm CAUTION! ** Accessories and add-on parts reduce the remaining load capacity for the occupant. 30 31 32 Eulerstraße 27 • 56235 Ransbach-Baumbach • Deutschland Telefon: (+49) 2623 / 92 499-0 • Telefax: (+49) 2623 / 92 499-99 E-mail: [email protected] • www.hoggi.de © by HOGGI GmbH_1910-2051-DE_12_2020 HOGGI GmbH ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Rigid aluminium frame
- Adjustable seat and backrest
- Tilting unit
- 90° footrest
- Self-propelling or push
- Indoor/outdoor use
- Child/adolescent
- 60kg load capacity
Frequently asked questions
The seat height is adjusted by moving the seat unit relative to the slots in the base plate. You can also vary it slightly by adjusting the screw connections inside the tilt base.
Active degree refers to the position of the backrest relative to the drive wheel axle. A higher active degree means the backrest is further behind the axle, allowing for more active driving. Adjust it by sliding the seat unit relative to the base plates through the slotted holes.
The backrest angle can be adjusted using a locking bolt on the back of the wheelchair. You can set it between -5° and +35°.