HOGGI SWINGBO 2 XL Wheelchair Service Manual

Partnerschaft für mobile Kinder
SWINGBO 2 & 2XL
Service instructions
en
SWINGBO 2 Service and maintenance instructions
Content
Page
1
Model identification & basic configuration
1.1 Model identification (label)_____________________________________________________4-5
1.2 Basic configuration__________________________________________________________4-5
2
Overview SWINGBO 2 & 2XL_______________________________________________________ 6
3
Common information_____________________________________________________________ 7
3.1
3.2
3.3
3.4
3.5
3.6
3.7
Preface____________________________________________________________________ 7
Application__________________________________________________________________ 8
Declaration of conformity_______________________________________________________ 8
Terms of warranty____________________________________________________________ 8
Customer service____________________________________________________________ 8
Service and repairs___________________________________________________________ 9
Packing and shipping instructions________________________________________________ 9
4
Safety Instructions______________________________________________________________ 10
3.1 Meaning of symbols_________________________________________________________ 10
3.2 Common safety instructions___________________________________________________ 10
5
Required tools and maintenance schedule__________________________________________ 11
5.1 Required tools______________________________________________________________ 11
5.2 Maintenance schedule_____________________________________________________12-13
6
Seat settings ___________________________________________________________________ 14
6.1 Seat height______________________________________________________________14-15
6.2 Seat depth_______________________________________________________________16-17
6.3 Active degree____________________________________________________________17-18
6.4 Back height______________________________________________________________18-19
6.5 Seat angle_______________________________________________________________19-20
6.6 Back angle adjustment_____________________________________________________20-22
6.7 Lower leg length__________________________________________________________22-23
6.8 Footrest angle and depth_____________________________________________________ 23
6.9 Armrest height & angle_____________________________________________________23-24
7
Maintenance schedule ___________________________________________________________ 25
7.1 Frame____________________________________________________________________ 25
7.2 Base plate and cross tube_____________________________________________________ 25
7.3 Rear axle__________________________________________________________________ 25
7.4 Seat unit__________________________________________________________________ 25
7.5 Back system & push bar/handle variant________________________________________26-27
7.6 Braking system___________________________________________________________28-29
7.7 Wheel fork holder_________________________________________________________29-30
7.8 Steering wheels_____________________________________________________________ 30
7.9 Rear wheel________________________________________________________________ 30
7.10 Push rim__________________________________________________________________ 30
7.11
7.12
7.13
7.14
7.15
7.16
7.17
7.18
7.19
7.20
7.21
7.22
7.23
7.24
7.25
7.26
7.27
Fender____________________________________________________________________ 31
Anti tip____________________________________________________________________ 31
Footrest hanger_____________________________________________________________ 32
Footrest bracket__________________________________________________________32-33
Footrests__________________________________________________________________ 33
Seat and back cushion_______________________________________________________ 34
Tie down kit________________________________________________________________ 34
Spoke guards______________________________________________________________ 34
Headrest Standard__________________________________________________________ 35
Headrest with occiput upholstery_______________________________________________ 35
Thoracic support____________________________________________________________ 35
Chest-/ thoracic support______________________________________________________ 35
Hip supports_______________________________________________________________ 36
Abduction block_____________________________________________________________ 36
Armrests__________________________________________________________________ 36
Therapy tray_______________________________________________________________ 36
Belt fixations_______________________________________________________________ 37
8
Operating life __________________________________________________________________ 38
9
Specifications__________________________________________________________________ 38
1 Model identification
1.1 Model identification (label)
(The label is attached to the axle tube)
Colour code
Article number
3346-10SB-XXX
SWINGBO 2
2021/05/15
Kantelbarer Rollstuhl
max. load
(01)04047349096062(21)202178999
2021178999
Hoggi GmbH
Eulerstr. 27
56235 Ransbach-Baumbach
MADE IN GERMANY
Serial number
50kg
CE label
3346-10SB-XXX
Classification / Product name
SWINGBO 2
2021/05/15
Kantelbarer Rollstuhl
max. load
(01)04047349096062(21)202178999
2021178999
Hoggi GmbH
Eulerstr. 27
56235 Ransbach-Baumbach
MADE IN GERMANY
Date of manufacture
50kg
Maximum load / load capacity
3346-10SB-XXX
SWINGBO 2
max. load
(01)04047349096062(21)202178999
Manufacturer
Place of manufacture
2021/05/15
Kantelbarer Rollstuhl
2021178999
Hoggi GmbH
Eulerstr. 27
56235 Ransbach-Baumbach
MADE IN GERMANY
Year of manufacture
UDI Code
50kg
1.2 Basic configuration
- Aluminium rigid frame with centre of gravity tilt in space
- Wheel base adjustable
- Knee lever wheel lock
- Rear wheels incl. push rims (removable via quick release axle)
- Seat depth adjustable by apx. 8 cm
- Choice of seat widths 24 -36 cm
- Push-handle or push-bar included
- Adjustable front seat height: 36 cm up to 47cm
- Adjustable tilt in space: -5° up to +45°
- Back angle adjustable
- Camber 3°, 6° or 9°
- Load capacity: 50 kg
4
1 Model identification
1.1 Model identification (label)
(The label is attached to the axle tube)
Colour code
Article number
3247-10SB-XXX
SWINGBO 2 XL
2021/05/15
Kantelbarer Rollstuhl
max. load
(01)04047349096062(21)202178999
2021178999
Hoggi GmbH
Eulerstr. 27
56235 Ransbach-Baumbach
MADE IN GERMANY
Serial number
100kg
CE label
3247-10SB-XXX
Classification / Product name
SWINGBO 2 XL
2021/05/15
Kantelbarer Rollstuhl
max. load
(01)04047349096062(21)202178999
2021178999
Hoggi GmbH
Eulerstr. 27
56235 Ransbach-Baumbach
MADE IN GERMANY
Date of manufacture
100kg
Maximum load / load capacity
3247-10SB-XXX
SWINGBO 2 XL
max. load
(01)04047349096062(21)202178999
Manufacturer
Place of manufacture
2021/05/15
Kantelbarer Rollstuhl
2021178999
Hoggi GmbH
Eulerstr. 27
56235 Ransbach-Baumbach
MADE IN GERMANY
Year of manufacture
UDI Code
100kg
1.2 Basic configuration
Mobility base:
- Aluminium rigid frame with centre of gravity tilt in space
- Wheel base adjustable
- Wheel lock integrated in side panel
- HOGGI light rear wheels incl. push rims (removable via quick release axle)
Seat system:
- Seat height adjustable
- Push-handle or push-bar included
- Adjustable tilt in space: -5° up to +45°
With low seat heights, a low degree of activity and low armrests, the tilt may be limited.
- Seat depth adjustable by apx. 8 cm
- hoice of seat widths 32 - 44 cm
- Load capacity: 100 kg
5
2 Overview SWINGBO 2 & 2XL
6
7
5
4
3
8
2
1
11
9
10
6
3 Common Information
3.1 Preface
Thank you for selecting the SWINGBO 2 / 2XL wheelchair. We have designed this
high-quality product to make your life safer and easier, and we’ve included this manual to
help you use and care for it. Please read the following instructions to make sure you use this
product as recommended. If you have any further questions, or if you have any problems,
please contact your healthcare provider.
We hope that SWINGBO 2 / 2XL meets your expectations.
We reserve technical modifi cations regarding the specifi ed model in this manual. Before
using the wheechair the fi rst time, this manual has to be read and understood by patient
and support personnel in oder to ensure a safe handling with the wheelchair.
Regular maintenance is important - it increases safety and prolongs the life of the product.
Every rehab product should be checked and serviced once a year.
However, it is recommended to check, readjust and, if necessary, service products with
a high frequency of use, with users in growth or users with a changing clinical picture at
6-month intervals.
Only original spare parts should be used for all service and maintenance work.
The service and maintenance work described here should only be carried out by trained specialist personnel and not by the user of the aid.
These service and maintenance instructions refer to the respective spare parts catalogs and
operating instructions of the products described. Please use all documents together.
Use the maintenance schedule (Chapter 5.2, Checklist to tick off) as a copy template.
Retain completed maintenance schedules and provide a copy to the customer.
SWINGBO 2 User manual
SWINGBO 2
Spare parts catalog
1910-0034-EN
SWINGBO 2 XL User manual
SWINGBO 2 XL
Spare parts catalog
1910-0035-EN
7
1910-1003-EN
1910-1005-EN
3.2 Application
SWINGBO 2 / 2XL wheelchair is designed solely for individual indoor and outdoor use by
childern and adolescents who are unable to walk or who have a walking impediment, and
can be operated by the patient or by another person.
Assistance may be required due to:
- Paralysis (paraplegia / tetraplegia or tetraparesis)
- Loss of limbs (dysmelia/lower limb amputation)
- Infantile/spastic cerebral palsy
- Spina Bifida
- Muscle and nerve disorders
- Osteogenesis Imperfecta
- Poliomyeliti
- There are no known contraindications when used as directed.
SWINGBO 2 / 2XL wheelchair is able to be used for further service. For further service the
product has to be cleaned and sanitised efficiently. Afterwards the product has to be checked
concerning condition, wearout and damage by an authorised technician. All damaged and
inapropptiate parts need to be changed. Some components can be used again, e.g. rear
wheels, steering wheels or push handles. Please see also the service manual for detailled
information.
3.3 Declaration of Conformity
HOGGI GmbH as manufacturer declares under sole responsibility that the SWINGBO
2 / 2XL system wheelchair meets the general safety and performance requirements to
Annex I of the Regulation (EU) 2017/745 of the European Parliament and of the Council.
Applicable harmonized standards have been applied. SWINGBO 2 / 2XL meets the
requirements of ISO 7176-8, DIN EN ISO 12182 and DIN EN ISO 12183.
3.4 Terms of Warranty
Warranty applies only when the product is used according to the specified conditions
and for the intended purposes, following all manufacturer’s recommendations.The
manufacturer is not responsible for damages caused by components and spare parts
not approved by the manufacturer. See also § 8 of terms and conditions on:
www.hoggi.de
3.5 Customer service
Our customer service will be happy to answer any technical questions you may have.
Please refer to the last page for contact addresses and telephone numbers.
8
3.6 Service and repairs
Service and repairs on the SWINGBO 2 / 2XL wheelchair may only be carried out by your
specialist dealer. In case of problems, contact your responsible specialist dealer. In case of
repairs, you will only receive original spare parts there.
Spare parts and replacement units are available during the entire service life of the product, but only for a maximum of 2 years after the sale of the last product in this series.
The wheelchair is custom made for the first time user. Therefore, no replacement wheelchair is available in the initial configuration. In order to ensure a correct spare parts delivery the serial no. of your wheelchair is required.
We are happy to help you find a dealer near you.
You can reach us at: [email protected]
3.7 Packing and shipping instructions
If SWINGBO 2 / 2XL has to be sent back to the manufacturer for repair or exchange the
product must be thoroughly cleaned/disinfected beforehand and put in a hygienically safe
condition.
Packaging is done by wrapping the product in a clean film, ideally with air cushions and
the subsequent use of a sufficiently large cardboard box, so that no transport damage can
occur.
9
4 Safety instructions
4.1 Meaning of symbols
Caution!
Warning of possible danger of accident and injury. Warning of possible technical
damage.
IInformation!
About use of product.
Information!
For service-personnel.
Attention!
Read manual before use!
4.2 Safety instructions
For all maintenance and repair work, you should generally observe a few points:
Attention!
Familiarize yourself with the functions of the product. If you are not familiar with the
product, study the user manual before testing. If no user manuals are available, request
them from us. You can also download documents from our homepage at: www.hoggi.de
Attention!
Study the service and maintenance instructions before starting work.
Attention!
Use suitable tools (see page 4 ff.).
Attention!
Wear suitable clothing and, if necessary, gloves and protective goggles.
Attention!
Secure the product from tipping over or falling down, e.g. from the workbench.
Attention!
Clean / disinfect the product before starting the test. If necessary, observe the instructions
in the user manual and product-specific test instructions.
Note!
Screws and nuts with thread locking are used for a large number of screw connections.
If you have to open such screw connections, replace the respective nut or screw with
one with new thread locking. If new nuts or bolts with thread locking are not available,
use liquid thread locking compound with medium strength (e.g. Loctite 241 or Euro Lock
A24.20).
10
5 Required tools and maintenance schedule
5.1 Required tools
The following list shows the tools and utilities required for service.
Reversible ratchet and sockets
size 8-24
Torque wrench
Measuring ranges 5-50 Nm
Wrench
Size 6 - 24
Hexagon wrench
Gr. 3 - 6
Screwdriver
Blade width 2.5 3.5 and 5.5
Phillips screwdriver
Size 2
Plastic hammer
Hammer approx. 300 g
Carpet knife with sickle and
standard blade
Side cutter
Liquid thread locking
„medium strength“
Riveting pliers for rivets up to
5 mm
11
Pos.
Customer:
...............................................
SWINGBO 2 / 2XL
Maintenance schedule
for regular inspection
System wheelchair
Check (Checklist to tick off )
Area
Serial number:
1.)
Function / Setting
(see instruction manual)
.......................................
2.)
none
damage / deformation
3.)
Screw connections
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
1. Basic product
1.1
Frame
- Damages
1.2
Base plates and Cross tube
- Active degree
- Seat height
1.3
Rear axle
- Seat height
1.4
Seat unit
- Tilt
- Seat depth
1.5
Back system & push bar/ handle
variant
- Height adjustment back
- Angle adjustment back
- Height adjustment for push bar/
handles
- Angle adjustment for push bar
- Remove
- Fold down
1.6
Braking system
- Brakes
1.7
Wheel fork holder
- Swivelling of the wheel forks
1.8
Steering wheels
- Tires
- Air pressure
- Running behavior of the wheels
1.9
Rear wheels
- Tires
- Air pressure
- Running behavior of the wheels
- Camber
- Quick release
1.10
Push rim
- Mounting position
Do the settings on the wheelchair
meet the user‘s requirements?
o
Notes:
12
1.)
Function / Setting
2.)
none
damage / deformation
3.)
Screw connections
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
2. Accessories
2.1
Fender
- Height adjustment
2.2
Anti tip and tip assist
- Anti tip
- Swivel away
- Angle adjustment
2.3
Footrest hanger
- Angle adjustment
2.4
Footrest bracket
- Lower leg length
- Folding away the footrest
- Footrest lock
2.5
Footrests
- Footrest angle
2.6
Seat / back cushion
- Cushion
2.7
Tie down kit
- Support of the anchorages
2.8
Spoke guards
- Spoke guards
2.9
Headrest standard with cushion
- Height adjustment
- Padding
2.10
Headrest with occiput upholstery
- Height adjustment
- Angle adjustment
- Padding
2.11
Thoracic support
- Height adjustment
- Width adjustment
- Depth adjustment
- Padding
2.12
Chest-/ thoracic support
- Height adjustment
- Width adjustment
- Depth and angle adjustment
- Padding
2.13
Hip support
- Width adjustment
- Depth adjustment
- Padding
2.14
Abduction block
- Pivot
- Removing
- Padding
2.15
Armrests
- Height adjustment
2.16
Therapy tray
- Clamping unit
2.17
Belt fixings:
Lap belt, 4-point lap belt, ankle
hugger
- Closures
Do the settings of the accessoires
meet the user‘s requirements?
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Notes
The maintenance was performed by: .............................................................. on: ......................................
13
6. Seat settings
6.1 Seat height
SWINGBO 2 offers seat height adjustment from 36 - 47 cm.
SWINGBO 2XL 45 - 53 cm
The seat height can be adjusted by screwing the connectors with the
bolting the connectors to the axle in different hole positions of the axle
mount.
On SWINGBO 2, the rear axle mounting offers 7 hole positions. The The
distances are 1 cm each, giving a total adjustment range of of 6 cm in
total.
SWINGBO 2 XL offers 10 hole positions, giving a total adjustment range
of 9 cm.
Steering wheel fork and hole position
2 different fork types are available. Short or long.
The short fork offers 3 hole positions, the long 4.
Depending on how the rear seat height is adjusted, the hole position of
the steering wheel in the fork must be adjusted.
Front and rear seat height must always be identical for SWINGO 2 and
2XL so that the steering wheels have full have full contact with the
ground.
14
Depending on the wheel camber, steering wheels and drive wheels, the following guidelines result for SWINGBO 2:
Depending on the wheel camber, steering wheels and drive wheels, the following guidelines result for SWINGBO 2:
15
6.2 Seat depth
SWINGBO 2 offers a seat depth adjustment range of 26 - 42cm.
Measured from the outer edge of the back to the front edge of the seat.
Adjustment range:
SWINGBO VTi: 24 - 42 cm
SWINGBO 2 XL: 30 - 50 cm
The following adjustment ranges result for SWINGBO 2 according to the seat width:
The following adjustment ranges result for SWINGBO 2 XL according to the seat
width:
To adjust the seat depth, a total of 4 screws must be loosened.
First, the chair is tilted to 45° to reach and loosen the front
screw connections.
Then the rear screws on the right and left can be loosened.
The seat panel can now be moved according to the specified information.
16
If the SWINGBO 2 is equipped with a wheel cover, this must be
removed before to expose visibly the two rear screws.
To do this, the marked screws must be completely removed. The wheel
cover can then be pulled out upwards.
6.3 Active degree
The active degree describes the ratio of the position of the backrest
relative to the drive wheel axis. The further the backrest is set behind
the the drive wheel axle, the more active SWINGBO 2 and 2 XL can be
driven.
SWINGBO 2 and 2 XL offer an active degree adjustment range of
level 0/1/2/3/4, each 2.5 cm
Total adjustment range is 10 cm
To adjust the active degree, remove the two screws fixing the wheel
cover and loosen the screw of the saddle clamping ring.
Setting active degree 0
The axle mount is completely extended and the rear screw connection
of the wheel cover is screwed into the rearmost hole of the frame.
This means passive driving.
Setting active degree 1
The axle mount is not completely extended and the rear screw
connection of the wheel cover is screwed into the penultimate hole of
the frame.
17
Setting active degree 2
The axle mount is extended relatively far and the rear wheel cover
wheel cover is screwed into the third last hole of the frame.
Setting active degree 3
The axle mount is extended relatively short and the rear wheel cover
is screwed into the fourth last hole of the frame. frame.
Setting active degree 4
The axle mount is only extended a short distance and the rear wheel
cover is screwed into the fifth last hole of the frame.
This means active driving
6.4 Back height
First of all, a distinction must be made between a trough-shaped backrest and an angle-adjustable backrest.
18
The trough back offers the following adjustment ranges depending
on the seat width for SWINGBO 2 and SWINGBO 2XL:
Seat width (SW)
24
26
28
30
32
34
36
Backrest height,
back trough shaped
36 - 44
37 - 45
38 - 48
39 - 49
40 - 50
42 - 54
43 - 55
Seat width (SW)
32
36
40
44
Backrest height,
back trough shaped
40 - 50
43 - 55
45 - 57
48 - 60
After loosening the indicated screw connections, the back can be
pulled out or pushed in.
The angle-adjustable back offers the following ranges:
Seat width (SW)
24
26
28
30
32
34
36
Backrest height,
panel angle adjustableped
33 - 42
35 - 44
37 - 46
39 - 48
41 - 50
43 - 52
45 - 54
Seat width (SW)
32
36
40
44
Backrest height,
panel angle adjustable
41 - 50
45 - 54
50 - 59
54 - 63
After loosening the indicated screw connections, the back can be
pulled out or pushed in.
6.5 Seat angle
The tilt in space of SWINGBO 2 and 2XL an be adjusted between -5°
and +45°.
13 positions of 4° each can be individually adjusted.
19
The tilt is triggered by a locking pin pull, which is controlled by a release
lever on the push bar or push handle.
6.6 Back angle adjustment
The back angle adjustment on the SWINGBO 2 and 2XL depends on
the
selected push bar/push handle variant and the corresponding back.
A distinction must be made here:
1. Push bar/handles removable with
angle adjustable back
2. Push bar/handles foldable with back in
trough shape
3. Angle-adjustable and foldable push
bar with trough-shaped backrest
Push bar/handles removable with back angle adjustable
The angle of the push handles themselves cannot be adjusted, but they
can be removed for small transport dimensions via clamping levers and
tripod springs.
!
The back sits here in front of the of the
push handles or the push bar and remains
unaffected by their function.
!
The back itself offers a total adjustment range of 40° and can be
operated via the release strap on the back.
In addition, the back can be folded forwards for small transport
dimensions.
Depending on how the back panel is screwed to the base, the
adjustment range is either 75°-115° or 80°-120°.
If the back plate is screwed in the positions shown on the left,
the adjustment range is 80°-120°.
If the backrest panel is screwed into the positions shown on the right
the adjustment range is 75°-115°.
20
Push bar/handles foldable with trough-shaped backrest
In contrast to the detachable push handles, the back is directly attached
to the foldable push handles. In addition, the back is always used in the
shape of a trough.
The back angle can be set to 5 different angles depending on how it is
screwed to the seat mount.
Front hole: 105°
Second hole: 100°
Third hole: 95°
Fourth hole: 90°
Rear hole: 85°
In addition, the back can also be folded down with the push handles/bars
to achieve a small transport size
To do this, the releases on the left and right are pushed upwards and
then the back is folded down.
Angle-adjustable and foldable push bar with trough-shaped
backrest
As with the foldable push handles/ bar, only the moulded backrest can
be used!
The back with the push handles/bars offers an adjustment range of of
40° and can be operated via the release strap on the back.
21
Depending on how the latch housing is screwed to the back base plate,
there is an adjustment range of either 75°-115° or 80°-120°.
If the housing is screwed in the upper position shown, the adjustment
range is 80°-120°.
If the housing is screwed in the lower position shown, the adjustment
range is 75°-115°.
Bolting point of the latch housing with locking bolt on the back base
plate.
6.7 Lower leg length
SWINGBO 2 und 2XL can basically be equipped with 3 different footrest
hanger.
Shown here is the footrest hanger 90°.
The footrest hanger can be swivelled up via the towing latches,
but not fixed.
SWINGBO 2 version for short LL (16-27 cm) or long LL (16-37 cm)
2XL version for short LL (20-36 cm) or long LL (20-41 cm)
Footrest hanger angle adjustable
Adjustable between 85° and 160° via clamping lever.
SWINGBO 2 version for short LL (19-27 cm) or long LL (19-37 cm)
2XL version for short LL (20-36 cm) or long LL (20-41 cm)
Single foot rest hanger, for individual adjustment of both legs
Adjustable between 85° and 160° via clamping lever.
SWINGBO 2 version for short LL (19-27 cm) or long LL (19-37 cm)
2XL version for short LL (20-36 cm) or long LL (20-41 cm)
22
The height of the footrest is adjusted by loosening the wing nuts on the
back.
The footrest mounted on the support can then be adjusted to the individual needs.
6.8 Footrest angle
The footrest angle is preset to 90°. The adjustment range is +- 10° (80°
- 100°).
After loosening the four marked screw connections on the footrest holder
the footrest can be adjusted in depth.
This changes the anchor point of the footrest and thus also the footrest
angle. The further the footrest is pulled out to the front, the the greater
the angle. If the procedure is reversed the angle decreases accordingly.
6.9 Armrest height and angle
SWINGBO 2 and 2XL offers various adjustable armrest heights.
Size 1: 14-21 cm
Size 2: 19-26 cm
Standard:
Tilt compensation: Size 1: 15-23 cm
Size 2: 18-26 cm
The standard armrests always remain firmly in position and move analogously to the wheelchair movement during the tilting movement.
The height can be adjusted in steps of 7x1.25 cm by repositioning the
front and rear screw connections.
23
The armrest with tilt compensation remains as horizontal as possible
during the tilting movement and is therefore more suitable for use with a
table.
The height can be adjusted in 6x1.5 cm steps by repositioning the front
and rear screw connections.
To loosen the screws, first tilt the chair to 45°.
Then the front screws can be loosened first.
Then loosen the rear screws and adjust the armrests to the desired
height.
By using a different hole position, the general angle of inclination can
also be adjusted.
If the front hole is used as shown here, the armrest is aligned more
steeply.
If the rear hole is used, the flatter and more horizontal the armrest is in a
tilted position.
24
7. Maintenance schedule
7.1 Frame
Functional test:
- Check for general damage or deformation to the frame structure
- Cracks in the construction
- Cross tube bolting
7.2 Base plates und cross tube
Functional test:
- Check for general damage
Check of the screw connections:
- Screw connections to the cross tube
- Connection of the side panels to the frame and to the internal adapter
plates
7.3 Rear axle
Functional test:
- Check for general damageg
- Height position of the axle correctly adjusted
- Wheel camber alignment
Check of the screw connections:
- Clamping screw of the connector
- Screwing the height position
- Screwing the connector to the axle mount
25
7.4 Seat unit
Functional test:
- Check for general damage
- Correct seat depth
- Tilt via locking bolt tension
Check of the screw connections:
- Seat frame to the support brackets for the adjustment of the seat depth
- Seat plate on the seat frame
- Seat mounts to the tilt bearings
7.5 Back system & push bar/handle variant
Functional test:
- Check for general damage
- Back panel height-adjustable and foldable
- Push handles or push bar removable or foldable
- Ratchet joint function for push handles
- Release of back angle adjustment
- Release of folding push bar/handles
Back panel angle and height adjustable with removable push handles or
push bar
Check of the screw connections:
- Screw connection for back height adjustment
- Connection to the seat adapter
1
- Connecting the crossbar to the back base
3
4
2
26
- Clamping lever for height adjustment of the push bar or handles
- Tripod spring for removal
- Screw connection of the crossbar to the seat
Backrest panel in trough shape
- Screw connection to the backrest height adjustment and to the clamps
on the push handles
- Connection to the seat adapter
- Connection via support strut to seat adapter
- Release of the folding mechanism
- Connection of the crossbar to the seat adaptert
- Push bar mounting to the back base panel
27
7.6 Braking system
Knee lever brakes
Functional test:
- Brake closure
- Faultless operation
- Visible damage
Brake HOGGI light
Brake opened
Functional test:
- Brake closure
- Faultless operation
- Visible damage
Brake closed
Check of the screw connections:
- Fixing the brake to the frame
Integrated brake system
Consisting of:
- Fender with integrated brake system
- Brake cable
- Brake
28
Functional test:
- Operability of the brake lever and smooth glide
- Good brake closure and contact pressure of the brake bracket
- Correct positioning of the brake lever in relation to the wheel. 90° angle
and 3-5 mm wheel protrusion
- Check for general damage
Check of the screw connections:
12
- Fastening the brake lever to the fender
- Fastening the brake bracket to the brake bracket holder
- Bowden cable correctly looped in the cable pulley
3
6
10
4
9
5
2
2
8
8
7
10
11
1
Drum brake
Functional test:
- Build-up of brake pressure (readjustment at adjusting screw)
- Checking the brake lever for general damage (locking lever, cracks)
- Checking the Bowden cable (kinks or cracks)
- Check the brake anchor and brake pads (contamination, wear)
Check of the screw connections:
- Connection brake anchor with adapter
- Connection of brake anchor adapter with side plate
- Bowden cable correctly hooked in
- Screw connection of the brake handle to the handle unit
7.7 Wheel fork holder
Functional test:
- Swiveling of the wheel fork
- Smooth running or fluttering -> Checking the alignment
- Check for general damage to the forks
29
Check of the screw connections:
- Screw connection of the wheel axle
- Bolting the steering fork axle to the frame
7.8 Steering wheels
Functional test:
- Check for general damage
- Check of the tread or profile (cracks, heavy wear)
- Wheel curvature too worn (tread max. up to 5mm to edge of wheel)
- Contamination in the area of the wheel bearing or the axle
7.9 Rear wheels
Functional test:
- Check for general damage
- Checking the treads and air pressure
- Checking the locking
- Checking the running behaviour of the wheel, clearance, mechanics of
the axle
- Checking of the correct alignment of the camber adapter and its bolting
Adjustment of the quick-release axle:
- The axle should be fitted with a minimum of clearance. If too much
movement is possible, the front nut is closed slightly clockwise with a
19 mm open-ended spanner in a clockwise direction, while the rear axle
is secured with an 11 mm open-ended spanner
- If the wheel is too tight, proceed in reverse order
7.10 Push rim
Functional test:
- Check for general damage
- Severe scratching and sharp edges
Checking the screw connections:
- Attachment of handrim to rim, also at correct distance
30
7.11 Fender
Standard fender
Functional test:
- Check for general damage
- Screw connection to the base plate firmly tightened
Fender with integrated armrests
Functional test:
- Height adjustment and latching of the armrest
- Damage to the armrest cushion
- Damage to the release button
- Screw connection to base plate firmly tightened
- Armrest holder firmly screwed to wheel cover
Fender with integrated brake system and armrests
Functional test:
- Check for general damage
- Height adjustment and latching of the armrest
- Damage to the armrest cushion
- Damage to the release button
- Checking the brake unit (see 6.4 Brake system)
- Screw connection to base plate firmly tightened
- Armrest holder firmly screwed to wheel cover
7.12 Anti tip
Functional test:
- Check for general damage
- Correct positioning (beyond the wheel radius, 2-3 cm above the floor)
- Checking the swivel mechanism
- Checking the length adjustment
Check of the screw connections:
- Connecting screws of the bracket to the axle
- Screw conncetion of the angle adjustment
31
7.13 Footrest hanger
Footrest hanger
Functional test:
- Check for general damage
- Distance to the seat plate
- Screw connection to the seat panel
Footrest hanger angle adjustable
Functional test:
- Check for general damage
- Swivel mechanism
- Clamping lever for angle adjustment
- Screw connection to the seat panel
Single foot rest hanger
Functional test::
- Check for general damage
- Swivel mechanism
- Clamping lever for angle adjustment
- Screw connection to the seat plate
7.14 Footrest bracket
Standard
Functional test:
- Check for general damage
- Swivel mechanism of the screwed-on footrest
- Correct adjustment of the foot angle
- Sliding of the holder on the tubes
With locking
Functional test:
- Check for general damage
- Swivel mechanism of the screwed-on footrest
- Correct adjustment of the foot angle
- Sliding of the holder on the tubes
- Locking bolt pull with locking latches, tension of the cable
32
Check of the screw connections:
- Wing screws for lower leg length adjustment
- Screw connection of the swivel mechanism
- Screw connection to the footboard with correct angle adjustment
7.15 Footrests
Footrest standard
Functional test:
- Check for general damage
- Screw connection to the footrest holder
Foot rest with heel stop
Functional test:
- Check for general damage
- Screw connection to the footrest holder
Aluminium footrest in frame colour
Functional test:
- Check for general damage
- Screw connection to the footrest holder
Single footplates in boat shape
Functional test:
- Check for general damage
- Screw connection to the footrest holder
33
7.16 Seat- and back cushion
Standard seat cushion
- Check for general damage (Velcro fastening, seams, holes or
strapped-through areas)
- Check for contamination
Seat cushion contoured
- Check for general damage (Velcro fastening, seams, holes or
strapped-through areas)
- Check for contamination
Back cushion
- Check for general damage (Velcro fastening, seams, holes or
strapped-through areas)
- Check for contamination
7.17 Tie down kit (ISO 7176-19)
Functional test:
- Check for general damage (deformation, sharp edges)
Check of the screw connections:
- Connection of the front lashing eye to the frame
- Screw connection of the pipe arch lashing eyelet In the frame.
7.18 Spoke guards
Functional test:
- Check for general damage (cracks)
- Fastening clips complete or defective
- Spoke guards suitable for wheel (drum brake or normal)
34
7.19 Headrest standard
Functional test:
- Check for general damage
- Checking the screw connection to the back panel
7.20 Headrest with occiput upholstery
Headrest bracket
Functional test:
- Check for general damage
- Checking the clamping ability
- Checking the screw connection to the back panel
Headrest with upholstery
Functional test:
- Adjustment possibilities
- Check for general damage (wear, cracks, etc.)
- Clamping ability
Checking the screw connections:
- Attachment of pad to support
7.21Thoracic support
Functional test:
- Check for general damage
- Screw connection of the pad holder to the back plateh
7.22 Chest-/ thoracic support
Functional test:
- Check for general damage
- Checking the belt buckle
- Screw connection of the pad holder to the back plate
35
7.23 Hip supports
Functional test:
- Check for general damage
- Width adjustment
- Depth adjustment on the seat plate and the pad itself
- Screw connection of the pad support under the seat plate
- Screw connection of the pad on the support
7.24 Abduction block
Functional test:
- Check for general damage
- Pivoting and latching mechanism
- Removal
Check of the screw connections:
- Bracket abduction block to the seat panel
7.25 Armrests
Standard
Functional test:
- Check for general damage
- Screw connection of the upholstery to the armrest support
- Connection of the armrest support to the seat mounting and to the tilt
bearing
Armrests with tilt compensation
Functional test:
- Check for general damage
- desired angle of inclination
- Screw connection of the cushion to the armrest support
- Connecting screw for tilt adjustment
- Connection of the armrest support to the seat support and to the tilt
bearing
7.26 Therapy tray
Functional test:
- Attachability and fixation of the table on the armrests
- Check for general damage (deformation, sharp edges)
Check of the screw connections:
- Connection of the front and rear fuse to the base plate
36
7.27 Belt fixations
Lap belt
Functional test:
- Check for general damage
- Check of the fastener
- Check of the screw connection of the bracket
4-point lap belt
Functional test:
- Check for general damage
- Check of the fastener
- Check of the screw connection of the bracket
Ankle hugger
Functional test:
- Check for general damage
- Check of the fastener
- Check of the screw connection of the bracket to the footrest
37
8 SWINGBO 2 / 2XL operating life:
The expected operating life of the SWINGBO 2 und 2 XL is 6 years, depending on the intensity of use, care
as well as maintenance. We recommend an annual inspection by the authorized specialist dealer.
In case of malfunctions or defects of the wheelchair, it must be immediately handed over to the medical supply
store or the specialist dealer.
9.1 Speficications SWINGBO 2
Seat width
24
26
28
30
32
34
Seat depth
26-30 cm 26-32 cm 26-34 cm 28-36 cm 30-38 cm 32-40 cm 34-42 cm
Back height
33-42 cm 35-44 cm 37-46 cm 39-48 cm 42-51 cm 42-52 cm 43-54 cm
Seat angle
-5° up to +45° Backrest angle
Back angle and height adjustable
75°-115° or from 80°-120° (in 10° steps)
Foldable push bar, handles
85°-105° (in 5° steps)
Lower leg length
16-37 cm
Footrest angle
-10° up to +10°
Seat height
36-47 cm
Rear wheel diameter
20“, 22“, 24“
Front wheel diameter
100 mm (4“),125 mm (5“), 140 mm (5,5“)
Camber
3°, 6°, 9°
Maximum load
50 kg
Weight
from 12 kg
Speficications SWINGBO 2 XL
Seat width
32
36
40
44
Seat depth
30-42 cm 34-46 cm 38-50 cm 38-50 cm
Back height
41-50 cm 45-54 cm 50-59 cm 54-63 cm
Seat angle
-5° up to +45° Backrest angle
Back angle and height adjustable
75°-115° or from 80°-120° (in 10° steps)
Foldable push bar, handles
90°-105° (in 5° steps)
Lower leg length
20-41 cm
Footrest angle
-10° up to +10°
Seat height
41-51 cm
Rear wheel diameter
22“, 24“
Front wheel diameter
100 mm (4”), 125 mm (5”), 140 mm (5,5”), 190 mm (7,5“)
Camber
3°, 6°, 9°
Maximum load
100 kg
CAUTION!
Accessories and add-on parts reduce the remaining load capacity for the occupant.
38
36
39
Eulerstraße 27 • 56235 Ransbach-Baumbach • Deutschland
Telefon: (+49) 2623 / 92 499-0
E-mail: [email protected] • www.hoggi.de
© by HOGGI GmbH_1910-2049-EN_04_2024
HOGGI GmbH
">