Advertisement
Advertisement
CONNECT PRO CASE 72300 - 10.2” (8th & 9th gen) - Black 72301 - 10.2” (8th & 9th gen) - White 72310 - Mini (4 & 5th gen) - Black 72329 - mini (6th gen) - Black 72330 - mini (6th gen) - White 72324 - Air 10.9” (4-5th gen) | Pro 11” (1st-3rd gen) - Black 72325 - Air 10.9” (4-5th gen) | Pro 11” (1st-3rd gen) - White 72326 - Pro 12.9” (3rd-5th gen) - Black 72327 - Pro 12.9” (3rd-5th gen) - White 1 CONNECT PRO CASE IPORT CONNECT PRO Case Install ManuThank you for purchasing the all new IPORT CONNECT Platform. We hope you enjoy this revolutionary new system and if at any time you need more assistance please contact IPORT Tech Support via Online chart or through our help desk. - IPORT Team Whats in box: 1 - IPORT CONNECT Case 1 - IPORT Security tool - 1.5mm hex key 1 - Info Card 1- Fit Pad Installation card and Pads* Product Info Page www.iportproducts.com/Product/cpcase Glossary of Terms: • Case - The fully assembled CONNECT PRO Case. • Case Top - The short removable portion of the chase including the locking portion of the Case. • IPORT Security Tool - The orange handled 1.5mm hex tool used for locking and unlocking IPORT Products. • Station Interface Module - The main electronics portion of the new IPORT CONNECT Platform consisting of the round electronic components. • Dock Interface Module - The secondary linear electronics found on the IPORT CONNECT Case. * included only in 12.9” Cases 2 CONNECT PRO CASE 1. Remove Case from the box and place on a table. 2. Remove the short Case Top. 3 CONNECT PRO CASE 3. Slide iPad into the Case making sure the lighting cable is snugly inserted into the iPad. 4 CONNECT PRO CASE 4. Reinstall the Case top onto the lower half if the Case and iPad. 5 CONNECT PRO CASE 5. Use the provided IPORT tool, insert the tool into the top of the case and slide the tool towards the lock position icon. 6 CONNECT PRO CASE • For added security rotate the IPORT tool clockwise to tighten the setscrew in place holding the lock secure. 7 CONNECT PRO CASE 6. Place the IPORT CONNECT Pro Case onto a BaseStation or WallStation for charing. 8 CONNECT PRO CASE Hand Strap Install - (sold separate) 1. Insert the metal strap loops with the flat end pointing towards the left or right side of the case. 9 CONNECT PRO CASE 2. Rotate the strap clip towards the bottom of the Case and insert into the hole until the strap clip snaps into place. 10 CONNECT PRO CASE 3. Repeat for the second clip. X2 4. Insert the IPORT CONNECT Hand Strap under both strap loops with the Velcro facing out from the case, fold over the Hand Strap and attach to the Velcro. Adjust hand strap to a snug but comfortable fit around the top of your hand. • NOTE Case Top and Bottom MUST be locked together to properly secure the iPad and CONNECT PRO Case together. 11 CONNECT PRO CASE Hand Strap Removal 1. Unlock the CONNECT PRO Case Top from the Case Bottom. See step 5 of installing the Case. 2. Remove the Case Top from the Case Bottom. 12 CONNECT PRO CASE 3. On the inside of the Case Top, locate the small oval hole and insert the IPORT CONNECT Security tool. Pivot the IPORT Security tool toward the top of the Case Top freeing the Strap loop. Rotate the Strap loop 90 degrees left or right to remove the Strap Loop from the Case Top. 4. Repeat for the second strap loop. 13 ">

Public link updated
The public link to your chat has been updated.
Advertisement