CONNECT
PRO
User Guide
Gigabit 30W PoE Injector
Package Contents
Check the following contents of your package:
z
PoE Injector
x1
z
User Guide x 1
z
Power Cord
x1
The label is attached to the bottom of the switch
If any part is lost and damaged,
please contact your local agent immediately.
Introduction
PoE Injector Provides fully complies with IEEE 802.3af/at standard,
and can work with all IEEE
802.3af /at PoE compliant PDs (Powered Devices) or PoE Receiver Adapters or other equivalent
product,
to expand your network to where there are no power line or outlet,
wish to fix device such as AP,
IP Camera or IP Phone,
where you
etc.
Hardware Description
Front Panel
The front panel composed by PSE output ports with data link port,
shown below:
the relevant indicator,
as
LED indicator
LED
Color
PoE
Green
Function
Off:
No PoE supply.
Light: Indicates the machine has PoE supply
Rear Panel
The rear panel of AC inlet power socket .
-1-
Installation
This part describes how to install your machine and make connections to it. Please follow the
following instructions in avoid of incorrect installation causing device damage and security
threat.
z Before cleaning the machine,
unplug the power plug of the machine first. Do not clean the
machine with wet cloth or liquid;
z Do not place the machine near water or any damp area. Prevent water or moisture from
entering the machine chassis;
z Do not place the machine on an unstable case or desk. The machine might be damaged
severely in case of a fall;
z Ensure proper ventilation of the equipment room and keep the ventilation vents of the
machine free of obstruction;
z Make sure that the operating voltage is the same one labeled on the machine;
z Do not open the chassis while the switch is operating or when electrical hazards are present
to avoid electrical shocks.
Desktop Installation
Install the Switch on a desktop,
Allow adequate space for ventilation between the device and
the objects around it. The bottom is shown in figure:
-2-
Wall-mounted installation
In the first two fixed screw on the wall as shown in the figure below
Aim at the two fixed hole switches,
and the machine smoothly on the screw
Note: The appliance inlet is served as disconnect device,
nstalled near the equipment and shall be easily accessible
-3-
the socket-outlet shall be i
PoE+
Injector
IPORT USB-C to
proprietary cable
PoE+
Adapter
(72102)
IPORT Surface Mount
70752, 70754
70755, 70756
70808, 70806
PoE+
PoE+
Injector
(72106)
Specifications
Model
Port
Standard
PoE Injector
Data in port:1 x 10/100/1000Mbps RJ45 port
PoE out port : 1x10/100/1000Mbps RJ45 port
IEEE802.3,
IEEE802.3u,
IEEE802.3ab,
IEEE802.3af,
IEEE802.3at
10BASE-T: UTP category 3, 4, ϱĐĂďůĞ;чϭϬϬŵͿ
Network Media(Cable)
100BASE-dy͗hdWĐĂƚĞŐŽƌLJϱĐĂďůĞ;чϭϬϬŵͿ
1000BASE-T: UTP category 5e ĐĂďůĞ;чϭϬϬŵͿ
Dimensions (L*W*H)
142 *60 *32 mm
mains input
AC 100V-240V 50/60Hz
PoE power output
DC 55V
PSE Power on RJ-45
Mode A: 1/2(+), 3/6(-)
PoE Output
30W(Max)
Temperature
Humidity
Power 30W
Operating Temperature: 0°C ~ 40 °C (32 °F ~104°F )
Storage Temperature: -40 °C ~ 70 °C (-40 °F ~158°F )
Operating Humidity: 10% ~ 90% non-condensing
Storage Humidity: 5% ~ 90% non-condensing
-5-
PoE+
Injector
PoE+ Upgrade Adapter or
PoE+ Adapter
(72109)
(72102)
IPORT CONNECT PRO
BaseStation
72352
72353
PoE+
PoE+
Injector
(72106)
PoE+
Injector
PoE+ Upgrade Adapter or
PoE+ Adapter
(72109)
(72102)
IPORT CONNECT PRO
WallStation
72350
72351
PoE+
PoE+
Injector
(72106)
">
