BK-UV002 Ver.1.0
Air Valve
SOLENOID VALVES 030 SERIES
INSTRUCTION MANUAL Ver.1.0
Handling Instructions and Precautions
Solenoid
Plug connector
Internal circuit
Attaching and removing plug connector
●DC12V, DC24V
Standard solenoid (Surge suppression)
Short circuit protection diode
w（＋）
Lead wire: DC12V: Brown
DC24V: Red
Flywheel
diode
e（−）
Lead wire: Black
Solenoid
Use fingers to insert the connector into the
pin, push it in until the lever claw latches
onto the protruded section of the connector
housing, and complete the connection.
To remove the connector, squeeze the lever
along with the connector, lift the lever claw
up from the protruded section of the connector housing, and pull it out.
1. Pre-wired common terminal at DC
positive side or AC.
Order code With straight connector: -CPSL
With L connector: -CPLL
（−）（−）（−）（−）（−）（−）
Connector
Connector housing
Color of COM, crossover wire:
DC12V ：Brown
DC24V ：Red
AC100V：Yellow
Polarity is for DC.
AC200V：White
Pin
Connector housing
Lever
Solenoid with LED indicator (Surge suppression)
Order code: -PSL, -PLL
Connector
assembly
LED indicator
(Light Emitting Diode)
Indication of polarity
（DC）
（＋）
Lead wire: DC12V: Brown
DC24V: Red
Connector
Contact
2. Pre-wired common terminal at DC
negative side
Order code With straight connector: -CMSL
With L connector: -CMLL
（＋）（＋）（＋）（＋）（＋）（＋）
（−）
Lead wire: Black
COM（＋）
Crossover wire
Protruded section
w and e are for with DIN connector (order code: -39).
COM（−）
C
LED indicator: Red
※Illustration shows the 110 series.
Crimping of connecting lead wire and contact
●AC100V, AC200V
Standard solenoid (Surge suppression)
w or e
Solenoid
Varistor
e or w
Lead wire: AC100V: Yellow
AC200V: White
To crimp lead wires into contacts, strip off
4mm [0.16in.] of the insulation from the end
of the lead wire, insert it into the contact,
and crimp it. Be sure at this time to avoid
catching the insulation on the exposed wire
crimping section.
Exposed wire 4mm
Contact
Lead wire
Equivalent to AWG22〜26
w and e are for with DIN connector (order code: -39).
Hook
Solenoid with LED indicator (Surge suppression)
Order code: -PSL, -PLL
LED indicator
(Light Emitting Diode)
Lead wire:
AC100V: Yellow
AC200V: White
Common terminal
pre-wired plug connector
Diode
LED indicator: AC100V: Yellow
AC200V: Green
Cautions: 1. Do not apply megger between the
lead wires.
2. The DC solenoid will not short circuit
even if the wrong polarity is applied,
but the valve will not operate.
3. Leakage current inside the circuit
could result in failure of the solenoid
valve to return, or in other erratic
operation. Always use it within the
range of the allowable leakage current. If circuit conditions, etc. cause
the leakage current to exceed the
allowable leakage current, consult us.
Insulation crimp tab
Insulation（Maximum outer
Exposed wire crimping
diameterφ1.7）
section
Cautions: 1. Do not pull hard on the lead wire.
2. Always use a dedicated tool for crimping
of connecting lead wire and contact.
Contact: Model 702062-2M
Manufactured by Sumiko Tech, Inc.
Crimping tool: Model F1-702062
Manufactured by Sumiko Tech, Inc.
Attaching and removing contact and connector
Insert the contact with a lead wire into a plug
connector □ hole until the contact hook latches
on and is secured to the plug connector.
Confirm that the lead wire cannot be easily
pulled out.
To remove it, insert a tool with a fine tip (such
as a small screwdriver) into the rectangular
hole on the side of the plug connector to push
up on the hook, and then pull out the lead wire.
Cautions: 1. Do not pull hard on the lead wire. It
could result in defective contacts,
breaking wires, etc.
2. If the pin is bent, use a small screwdriver, etc. to gently straighten out
the pin, and then complete the connection to the plug connector.
Crossover wire
Connector
Connector housing
Color of COM, crossover wire:
DC12V：Black
DC24V：Black
Cautions: 1. The diagrams show the straight connector configuration.
While the connector’s orientation is
different in the case of the L connector, in every case the first COM lead
wire comes from the last station’s
mounted valve.
2. Since the COM terminal is connected
to a crossover terminal inside the
connector housing, the connector
cannot be switched between a positive common and a negative common
by changing the connectors.
Manual override
Non-locking type
Mounting base 030-21
To operate the manual override, press it all the
way down. The valve works the same as when
in the energized state as long as the manual
override is pushed down, and returns to the
rest position upon release.
When installing a mounting base to the
valve, always use the provided screws. The
recommended tightening torque for the
screws is 49N・cm {5kgf・cm} [4.3in・lbf].
Mounting valves on manifold
When mounting valves on manifold, apply
the recommended tightening torque
of 39.2N・cm {4kgf・cm} [3.5in・lbf] for the
valve mounting screws.
PU
SH
※Illustration shows the 110 series.
Locking protruding type
Use a small screwdriver to turn the adjusting
knob several times in the clockwise direction,
and lock the manual override in place.
When locked, turning the adjusting knob
several times in the counterclockwise direction
releases a spring on the manual override,
returns it to the original position, and releases
the lock.
For the locking protruding type, when the
adjusting knob is not turned, this type acts just
like the non-locking type, the valve is
energized as long as the manual override is
pushed down, and it returns to the rest
position upon release.
PU
SH
※Illustration shows the 110 series.
Cautions: 1. In the pilot type solenoid valve, the
manual override cannot switch the
main valve without air supplied from
the 1(P) port.
2. Always release the lock of the locking
protruding type manual overrides
before
commencing
normal
operation.
3. Do not attempt to operate the manual
override with a pin or other object
having an extremely fine tip. It could
damage the manual override button.
4. Do not turn the adjusting knob more
than needed. It could result in
defective operation.
Made to Order
The 030 series Solenoid Valves include a variety of made to order solenoids for
application in a broader range of control and wiring types.
Plug connector
Straight connector
with LED indicator
DIN connector
L connector with
LED indicator
-39
-PSLN
● Without lead wire
● Connector and
contacts included
-PLLN
● Without lead wire
● Connector and
contacts included
●When ordering, enter -PSLN or -PSLL in place of the normal
option code for the wiring type.
A compact connector that is highly resistant to
dust and water splashes.
Employs a self-stripping method that
eliminates the need for de-sheathing the lead
wire.
● When ordering, enter -39 in place of the normal option code
for the wiring type.
● A varistor for surge suppression is also equipped.
(For the AC100V and AC200V only. For the DC12V and
DC24V, a flywheel diode for surge suppression is installed as
standard equipment.)
● LED indicator is not available.
Lead wire length
Wiring instructions
-1L
-3L
● For plug connector
● Length
-1L：1000 [39]
mm [in.]
-3L：3000 [118]
●For lead wire length, -1L is 1000mm [39in.] and -3L is 3000mm
[118in.].
When ordering, enter -1L or -3L following the wiring type option
code.
●Solenoid with DIN connector
When de-sheathing (only the outer sheath of the cabtyre), pay attention
to the lead wire direction. The cover will be easily mounted when the
lead wire on the outer side of the terminal cover is set about 8mm
longer than the inner side.
Without stripping off the sheath, insert the lead wire until it contacts the
lead wire stopper on the terminal body, and then place the contact from
the upper side. Then use pliers to press the lead wire further to ensure
that the contacts are firmly touching the core wire.
JIS C3306
VCTF
Conductor: 0.75mm2
[1.16×10–3 in.2]
Finished: outside 6.6 (2 leads)
7.0 (3 leads)
Cable
1
2
+
3
_
Cable gland
Solenoid terminal
arrangement
Cable gasket
Washer
Contact
Lead wire
stopper
Lead wire
Gasket
Cover mounting
screw
Terminal
cover
Lead wire
Gasket
Terminal body
Terminal body
Pliers
The appropriate tightening torque for the cover mounting screw is
29.4N・cm {3kgf・cm} [2.6in・lbf].
LED indicator
The LED indicator for confirmation of
operation is also available without a plug
connector. This creates a clean monoblock
look with a compact cover.
-L
● When ordering, enter -L in place of the normal option code for
the wiring type.
● A varistor for surge suppression is also equipped.
(For the AC100V and AC200V only. For the DC12V and
DC24V, a flywheel diode for surge suppression is installed as
standard equipment.)
Built-in interface unit
-FA
Includes an interface unit with photo transistor.
Can be directly controlled by a microcomputer and logic chip, and is equipped with full
electric noise countermeasures and LED
indicators.
Electrical Specifications for Solenoid Valve with Built-in Interface Unit
Item
Input side
● When ordering, enter -FA in place of the normal option code
for the wiring type.
● Cannot be ordered in combination with any other solenoid
option.
● Rated voltages for the solenoid are AC100V and AC200V only.
DC V
5
Voltage range
DC V
4〜6
Current (when 5V DC is applied) mA
Operating voltage
DC V
Return voltage
DC V
Lead wire:
Red ＋
Solenoid
Zero
cross
circuit
Lead wire:
Black ー
＜Solenoid side＞
LED
Condenser
varistor
Rated voltage
AC V
90〜125
（100 ＋25
−10 ％）
180〜250
（200 ＋25
−10 ％）
Hz
50
60
50
60
Starting mA (r.m.s.)
36
32
18
16
24
20
12
10
Frequency
Current
Solenoid
side
(
when rated
voltage is
applied
200
Shading type
) Energizing mA (r.m.s.)
Leakage Frequency Hz
current
Current mA (r.m.s.)
50
60
50
60
0.3
0.4
0.6
0.8
Surge suppression (as standard)
Built-in varistor at solenoid side
Color of lead wire
Yellow
White
Color of LED indicator (as standard)
Yellow
Green
Dielectric voltage
Insulation resistance
Zero-cross function
Wiring type and lead wire length
Min. AC1500V on input side and solenoid side
Between input side and
Over 100
MΩ solenoid side, and between
whole terminals and body
Available
Grommet type: 300mm [11.8in.]
Wiring instructions
Example of control circuits
1. Control by transistor
100
Type
Lead wire color:
AC100V: Yellow
AC200V: White
The interface unit is a triac with photo coupler. Applying DC5V to the
input terminals when AC power is applied on the solenoid side causes
the LED inside the unit to light up, turns on the triac, and energizes the
solenoid. At this time, a LED indicator turns on.
When the input side voltage reaches 0V, the LED inside the unit shuts
off, the triac is turned off, and the solenoid is de-energized. At this time,
the LED indicator is turned off.
With a built-in zero-cross circuit, the zero-cross voltage is used to turn
the power on, and the zero-cross current to turn it off.
0.8 or over
Red (＋), Black (−)
Operating voltage range AC V
Interface
unit
18
4 or below
Color of lead wire
Block diagram
＜Input side＞
Specifications
Rated voltage
Vcc
Red
NPN type
Lead wire color:
Solenoid power AC100V: Yellow
Solenoid power AC200V: White
AC power
supply
Black
AC100V: Yellow
Interface solenoid AC200V: White
valve
Vcc
Lead wire color:
Input ― DC0V: Black
Lead wire color:
Input ＋ DC5V: Red
Interface solenoid
valve
AC100V: Yellow
AC200V: White
AC power
supply
Red
PNP type
Black
2. Control by TTL, IC
Interface solenoid valve
AC power
supply
AC100V: Yellow
AC200V: White
Black
TTL
Example: 7406 (able to control up to 2 interface
74LS244
solenoid valves.)
3. Control by relay contact
Interface solenoid
valve
AC100V: Yellow
Red
Black
AC200V: White
AC power
supply
Vm＜6.0V（Vm: Peak voltage）
Vn＞4.0V（Vn: Lowest voltage）
Vn
contact
Vm
Vcc
1. Separate the input side and solenoid side lead wires by color. Never
apply AC power/6VDC or more to the input side.
2. Ensure that voltage ripple on the input side remains within the range
shown below:
0V
4. When input is not
a DC5V power supply
Install resistance to the
outside to drop the input
voltage to 4〜6V.
Vp
Red
AC power
supply
Black
VcE R1
AC100V: Yellow
Interface solenoid AC200V: White
valve
Example
R1＝
Vp-5-VCE
〔Ω〕
18×10-3
Vp〔Ｖ〕
R1
12
390Ω1/4W
24
1.0KΩ1W
In the case of VCE=0〔Ｖ〕
3. Even when a wrong polarity is applied to the input side, a built-in
diode for protection against reverse polarity eliminates any worry
about short circuiting. The valve will not operate, however.
4. A varistor and condensor are built-in to the solenoid power supply
side, for protection circuit against external surge voltages. As a
result, there is a 0.3mA leakage current in AC100V, and a 0.6mA
leakage current in AC200V.
5. The operation and return times of the interface unit are 10ms or less
with a 50Hz AC power supply, and 8ms or less with a 60Hz AC
power supply.
SOLENOID VALVES
SERIES
Cylinder Operating Speed
Basic Models and Valve Functions
How to obtain cylinder speed
030-4E1
Number of ports
2, 3 ports
5 ports
Valve function
Normally closed (NC)
Single solenoid
Remark: For optional specifications and order codes, see p.91〜92.
Specifications
Item
Basic model Direct piping,
T, F, F01 type manifolds
030E1
030-4E1
Air
Media
Operation type
mm2
Effective area〔Cv〕
Direct acting type
Internal pilot type
1
（P）
→2
（A）
0.6〔0.03〕
2
（A）
→3
（R）
0.8〔0.04〕
（
1 P）
→4
（A）
,（
2 B）
0.6
〔0.03〕
（
4 A）→5（R1）,（
2 B）→3（R2）0.8〔0.04〕
Port size Note
M5×0.8
Lubrication
Not required
Operating pressure range MPa {kgf/cm2} [psi.]
0〜0.7 {0〜7.1} [0〜102]
MPa {kgf/cm2} [psi.]
1.05 {10.7} [152]
Response time
ON/OFF
DC12V, DC24V
10/25 or below
AC100V, AC200V
Maximum operating frequency
15/40 or below
5
Hz
Operating temperature range (atmosphere and media) °C [°F]
5〜50 [41〜122]
m/s2{G}
Shock resistance
117.7 {12.0}
Any
Mounting direction
t3 Time
To obtain the time required for the cylinder to
complete 1 stroke, add the cylinder’s delay time
t1 (time between energizing of the solenoid valve
and actual starting of the cylinder), to the
cylinder’s max. speed operating time t2.
When a cushion is used, add the cushioning time
t 3 , to the above calculations. The standard
cushioning time t3 is approximately 0.2 seconds.
Measurement conditions
0.15〜0.7 {1.5〜7.1} [22〜102]
Proof pressure
ms
t2
Cylinders start
Solenoid valve
energized
t1
Cushioning
impact
2 positions
Number of positions
Cylinder stop
030E1
Cylinder stroke
Item
Basic model Direct piping,
T, F, F01 type manifolds
●Air pressure: 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length:
φ2.5 [0.1in.]×1000mm [39in.]
●Fitting:
Quick fitting
Valve side:
TS4-M5
Cylinder side:
TS4-M5 (φ10, φ16)
TS4-01 (φ20)
Load
●Load ratio=
(%)
Cylinder theoretical thrust
●Cylinder stroke: 60mm [2.36in.] (φ10,φ16)
100mm [3.94in.] (φ20)
Load
Cylinder
Note: For details, see the port size on p.90.
Solenoid valve 030-4E1
0.5MPa
Fitting TS4-M5
or TS4-01
Solenoid Specifications
Fitting TS4-M5
Maximum operating speed
Rated voltage
DC12V
Item
DC24V
AC100V
Type
Operating voltage range
V
10.8〜13.2
(12±10%)
21.6〜26.4
(24±10%)
Frequency
Hz
─
Starting
mA (r.m.s.)
Energizing
mA (r.m.s.)
Insulation resistance
90〜132
(100＋32
−10 %)
180〜264
(200 ＋32
−10 %)
─
50
60
50
60
─
─
36
32
18
16
130 (1.6W)
65 (1.6W)
140 (1.7W) with
LED indicator
75 (1.8W) with
LED indicator
24
20
12
10
〔
〕 〔
8
〕
4
MΩ
4
Grommet type: 300mm [11.8in.]
and lead
wire length Optional
Plug connector type: 300mm [11.8in.]
Note: See made to order on p.97〜98.
Color of LED indicator
Surge suppression (as standard)
1000
800
600
φ10 [0.394in.]
φ16 [0.630in.]
400
φ20 [0.787in.]
200
10
20
Over 100
Wiring type Standard
Color of lead wire
1200
0
2
Red (＋)
Black (−)
Brown (＋)
Black (−)
Red
Flywheel diode
Yellow
s
White
Yellow
Green
Varistor
30 40
Load ratio
50
60
70
％
1mm/s = 0.0394in./sec.
Delay time
Delay time
Maximum allowable leakage current mA
Shading type
Maximum operating speed
mm/s
Flywheel diode incorporated
for surge suppression
Current
(when
rated
voltage is
applied)
AC200V
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
φ20 [0.787in.]
φ16 [0.630in.]
φ10 [0.394in.]
10
20
30 40
Load ratio
50
60
70
％
Note: Delay time changes depending on the valve
construction, the volume of the cylinder and
piping.
Flow Rate
Solenoid Valve Port Size
MPa
Supply pressure
(MPa)
Valve outlet pressure
0.7
0.6
Port specification
Port size
Female thread
M5×0.8
─
φ1.8
Female thread
M5×0.8
─
φ1.8
Port
Location of piping ports
Port size
1(P)
Manifold
2(A)
Valve
3(R)
Manifold
1(P)
Manifold
4(A), 2(B)
Valve
3, 5(R)
Manifold
1(P)
Manifold
Rc1/8
4(A), 2(B)
Valve
M5×0.8
3, 5(R)
Manifold
Rc1/8
1(P)
2(A)
0.7
3(R)
0.6
0.4
1(P)
0.5
0.3
0.3
0.2
0
Port
030E1
0.5
0.1
Basic model
0.4
4(A), 2(B)
030-4E1
3(R2), 5(R1)
0.2
0.1
10
20
30
40
50
Flow rate R/min (ANR)
1MPa = 145psi., 1R/min = 0.0353ft.3/min.
How to read the graph
When the supply pressure is 0.5MPa
[73psi.] and flow rate is 29R/min
[1.02ft.3 /min.] (ANR), the valve outlet
pressure becomes 0.4 MPa [58psi.].
Manifold Port Size
Manifold model
YM□T
YM□F
YM□F01
Solenoid Valve Mass
g [oz.]
M5×0.8
M6×1
M5×0.8
M6×1
Manifold Mass
g [oz.]
Basic model
Mass
030E1
57 [2.01]
Manifold
model
030-4E1
71 [2.50]
YM□T
(11×n)−1
YM□F
(20.5×n)−1 [(0.72×n)−0.04]
YM□F01
(20×n)＋23
Mass calculation of each unit
(n=number of units)
Block-off
plate
[(0.39×n)−0.04].5
[(0.71×n)＋0.81].
3 [0.11]
Operating Principles and Symbols
3-port
Normally closed (NC)
2（A）
1（P）
3（R）
030E1
De-energized
Column
Solenoid cover
Molded solenoid
Energized
Shading coil
(AC solenoid only)
Major Parts and Materials
Parts
Plunger
Body
Plunger spring
O-ring
Plunger pin
Manual override
Body
Flapper
Valve
1（P）
1（P）
2（A）
3（R）
Flapper
Manifold
Single solenoid
4（A）
2（B）
5（R1）
1（P）
3（R2）
030-4E1
De-energized
Energized
Shading coil
(AC solenoid only)
Plunger
Plunger spring
Plunger pin
Manual override
Body
1（P）
1（P）
4（A）
Flapper
2（B）
Synthetic rubber (urethane)
Plunger
Magnetic stainless
steel
Spring
Stainless steel
Mounting base
Mild steel (zinc plated)
Body
Aluminum alloy (anodized)
Block-off plate
Mild steel (zinc plated)
Bracket
Mild steel (nickel plated)
Seal
Synthetic rubber
Remark: Materials that generate copper ions are
not used for the non-ion specification.
5-port, 2-position
Column
Solenoid cover
Molded solenoid
Synthetic rubber
Diaphragm
Column
3（R）
2（A）
Materials
Aluminum alloy (anodized)
5（R1）
4（A）
Diaphragm
5（R1）
3（R2）
3（R2）
2（B）
Dimensions of Solenoid Valve (mm)
030E1
030-4E1
030E1
Approximately
300
24
15
15
24
Manual override
Non-locking type：Standard
Locking protruding type：-83
2（A）
2-M5×0.8
60.7
1（P）
12
2（B）
2（B）
2-φ2.8 Counterbore φ5.4 Depth 3
Mounting hole
1（P）
4（A）
4（A）
23.5
8
11
M5×0.8
11
Approximately
300
8.5
48.2
Manual override
Non-locking type：Standard
Locking protruding type：-83
2（A）
030-4E1
11
2-φ2.8 Counterbore φ5.4 Depth 3
Mounting hole
2-M3×0.5
Depth 2.5〜6.5
Mounting thread
2-M3×0.5
Depth 2.5〜6.5
Mounting thread
M5×0.8
1（P）
1（P）
8.5
26.5
3
（R）
9
5（R1）
3（R2）
13 8
14
M5×0.8
2-φ1.8
18
18
φ1.8
9
※The lead wire direction is to the opposite side from the manual override and A, B port.
Additional Parts
(To be ordered separately)
Options
Made to Order
●Mounting base：030-21
●Locking protruding type manual override：-83
●Solenoid with DIN connector：-39
030SOL
φ14.8
（2.4）
C
（44.1）
6.5
1.6
54
M12×1.25
（34.5）
φ6
13
（27） 7.5
E
（To the top surface
5 of the valve）
030ROCK
●Solenoid with straight connector：-PSL
030SOL
34
●Solenoid with LED indicator：-L
10
R
030SOL
LED indicator
28
10
Approximately
24.5 300
28.2
A
34
36
24
2-φ4.5
Mounting hole
40
LED indicator
●Built-in interface unit：-FA
●Solenoid with L connector：-PLL
030SOL
030SOL
44
44.5
20
約300
D
29
B
20.5
30.5
R
LED indicator
LED indicator
※The lead wire direction is to the side with the
manual override and 4(A), 2(B) port.
Code
A
B
C
D
E
R (Lead wire length)
Remarks
030E1
56
49
64.1
50.5
53.2
030-4E1
68.5
61.5
76.6
63
65.7
-PSL, -PLL: 300
Made to order: -1L: 1000, -3L: 3000
Overall length to the
end of the valve
Model
Dimensions of Manifold for 2-, 3-port valves (mm)
YMT
YM□T
L
8 16
16 8
15
15
Manual override
Non-locking type：Standard
Locking protruding type：-83
24
Approximately
300
2-M5×0.8
(With 1 plug)
2
15.5
22
7.5
M5×0.8
17.5
（R）
3
1（P）
20
Unit dimensions
20.5
030E1
Block-off plate
19
15
12
5
25
50
2-M3 Depth 4.5
Mounting thread Note
10
2-φ4.5 (Mounting hole)
8
P1
8
4-M3 Depth 4.5
Bracket mounting thread
16
P2
16
Note: Not available with YM2T
stn. 1 stn. 2
Additional Parts
(To be ordered separately)
●Muffler：KM-06
For manifold only
030MUFF
Model
L
P1
YM2T
32
16
─
YM3T
48
32
16
YM4T
64
48
32
YM5T
80
64
48
YM6T
96
80
64
YM7T
112
96
80
YM8T
128
112
96
YM9T
144
128
112
YM10T
160
144
128
Options
Made to Order
●Locking protruding type manual override：-83
●Solenoid with DIN connector：-39
030ROCK
030SOL
φ6
φ14.8
16
6
13
（2.4）
（34.5）
（44.1）
C
●Solenoid with straight connector：-PSL
54
M12×1.25
6.5
4
（11.5）
P2
（27） 7.5
10
15
50.2
2-M6×1
(With 1 plug)
030SOL
10
Width across flats
M6×1
34
10
●Solenoid with LED indicator：-L
R
030SOL
34
Approximately
24.5 300
28.2
36
A
10
LED indicator
LED indicator
●Solenoid with L connector：-PLL
●Built-in interface unit：-FA
030SOL
030SOL
44
44.5
30.5
D
29
20.5
B
20
Approximately
300
R
LED indicator
LED indicator
※The lead wire direction is to the side with the
manual override and 4(A), 2(B) port.
Code
A
B
C
D
R(lead wire length)
Remarks
030E1
56
49
64.1
50.5
030-4E1
68.5
61.5
76.6
63
-PSL, -PLL: 300
Made to order: -1L: 1000, -3L: 3000
Overall length to the end of
the valve
Model
Manifold for combination mounting of 2-, 3-, 5-port valves (mm)
YMF
YM□F
L
Manual override
Non-locking type：Standard
Locking protruding type：-83
8 16
16 8
15
15
24
Approximately
300
2-M5×0.8
(With 1 plug)
18.5
37
2
19
2-M5×0.8
31.5
1（P）
3・5（R）
15
10.5
22.5
35
62.7
2-M6×1
(With 1 plug)
030-4E1
Block-off plate
50
4-M3 Depth 4.5
Mounting thread Note
4
15
8
2-φ4.5
Mounting hole
P1
8
8
4-M3×0.5 Depth 4.5
Bracket mounting thread
stn. 1 stn. 2
4
5
26
25
Unit dimensions
16
P2
16
Note: 2 places for YM2F.
Model
L
P1
YM2F
32
16
P2
─
YM3F
48
32
16
YM4F
64
48
32
YM5F
80
64
48
YM6F
96
80
64
YM7F
112
96
80
YM8F
128
112
96
YM9F
144
128
112
YM10F
160
144
128
YMF01
YM□F01
L
18
16
6
16
15
18
15
10.5
24
Approximately
300
2-M5×0.8
4
15
5
25
50
Block-off plate
2-φ4.5
Mounting hole
33
1（P）
16
18
030-4E1
8
8
stn. 1 stn. 2
P2
8
4-M3×0.5 Depth 4.5
Bracket mounting thread
4-Rc1/8
(With 2 plugs)
3・5（R）
40
22.5
10.5
22.5
15
62.7
2-φ4.5
Mounting hole
42
Manual override
Non-locking type：Standard 10.5
Locking protruding type：-83
P1
2
6
Unit dimensions
Model
L
P1
P2
YM2F01
52
40
16
YM3F01
68
56
32
YM4F01
84
72
48
YM5F01
100
88
64
YM6F01
116
104
80
YM7F01
132
120
96
YM8F01
148
136
112
YM9F01
164
152
128
YM10F01
180
168
144
YM11F01
196
184
160
YM12F01
212
200
176
YM13F01
228
216
192
YM14F01
244
232
208
YM15F01
260
248
224
YM16F01
276
264
240
YM17F01
292
280
256
YM18F01
308
296
272
YM19F01
324
312
288
YM20F01
340
328
304
030 Series Solenoid Valve Order Codes
■ 2-, 3-port valve
■ Manual override
Non-locking type
manual override
3-port
2（A）
■ Wiring type
● Lead wire length:
300 mm [11.8in.] is
standard.
Number of ports
Grommet type
1（P）
3（R）
Blank
Blank
Locking protruding type
manual override
2-port
2（A）
Blank
Straight connector
with LED indicator
1（P）
-2
-83
-PSL
L connector with
LED indicator
-PLL
Basic model
030E1
2-, 3-port
Voltage
-2
-83
Direct piping
030-4E1
5-port
●When ordering the non-ion specification, enter
-NCU after the basic model code.
Additional Parts
Muffler
Mounting base
KM-06
●For manifold
only
Block-off plate
030-21
● YM F -BP
YM─For YM
T—For T type manifold
F—For F type manifold
(For F01 type manifold)
-PSL
-PLL
DC12V
DC24V
AC100V
AC200V
030 Series Manifold Order Codes
■ 2-, 3-port valve
■ Manual override
Non-locking type
manual override
3-port
2（A）
■ Wiring type
● Lead wire length:
300 mm [11.8in.] is
standard.
Number of ports
Grommet type
1（P）
3（R）
Blank
Blank
Locking protruding
type manual
override
2-port
2（A）
Blank
Straight connector
with LED indicator
L connector with
LED indicator
1（P）
-2
-83
-PSL
-PLL
Pre-wired common
terminal
Straight connector
with LED indicator
Pre-wired common
terminal
L connector with
LED indicator
-CPSL
-CMSL
-CPLL
-CPLL
-CMLL
-CMLL
●-CP□L：Positive common of DC12V,
DC24V, and AC100V, AC200V.
●-CM□L：Negative common of DC12V
and DC24V.
Manifold model
Number of units
Manifold for 2-, 3port valves
Manifold for
combination
mounting of 2-,
3-, 5-port valves
Station
T
2
⁝
20
YM
stn.1
⁝
stn.n
F
F01
Basic model
Voltage
030E1
-2
030E1
-2
-83
-CPSL
-PSL -CMSL
-PLL -CPLL
-CMLL
-83
030-4E1
●For 11 or more stations,
use F01 only.
●Specify the valve type for each
station.
●Enter -BP when closing a station
with a block-off plate without
mounting a valve.
●When ordering the non-ion
specification, enter -NCU after the
basic model code.
●Valve mounting location from the lefthand side when facing the 4(A), 2(B)
ports.
Made to Order For details, see p.97〜98.
Straight connector
with LED indicator
-PSLN
●Without lead wire
●Connector and
contacts included
L connector with
LED indicator
Lead wire length
DIN connector
-PLLN
-1L
-3L
-39
●Without lead wire
●Connector and
contacts included
●For plug connector ●Cannot be used
Length -1L：1000
with -L.
(mm)
[39in.]
-3L：3000
[118in.]
LED indicator with
built-in varistor
-L
●Cannot be used
with -39.
Built-in interface
unit
-FA
●Can be directly
controlled by output
from micro computer or
other logic devices.
●With LED indicator
DC12V
DC24V
AC100V
AC200V
●Pre-wired common
terminal for AC100V and
AC200V is either
-CPSL or -CPLL.
">
