Koganei 110 Solenoid valve Instruction manual

BK-UV002 Ver.1.0
Air Valve
SOLENOID VALVES 110 SERIES
INSTRUCTION MANUAL Ver.1.0
Handling Instructions and Precautions
Solenoid
Internal circuit
●DC12V, DC24V
Standard solenoid (Surge suppression)
Short circuit protection diode
w（＋）
Lead wire: DC12V: Brown
DC24V: Red
Solenoid
Flywheel diode
e（−）
Lead wire: Black
w and e are for with DIN connector (Order code : -39).
Solenoid with LED indicator
(Surge suppression)
Order code：-PSL, -PLL
Cautions: 1. Do not apply megger between the
lead wires.
2. The DC solenoid will not short
circuit even if the wrong polarity is
applied, but the valve will not
operate.
3. Leakage current inside the circuit
could result in failure of the
solenoid valve to return, or in other
erratic operation. Always use it
within the range of the allowable
leakage current. If circuit conditions, etc. cause the leakage
current to exceed the allowable
leakage current, consult us.
4. For double solenoid and twin
solenoid, avoid energizing both
solenoids simultaneously. The
valve could fall into a neutral
position.
LED indicator
（Light Emitting Diode）
Plug connector
（＋）
Lead wire: DC12V: Brown
DC24V: Red
（−）
Lead wire: Black
Attaching and removing contact and connector
Insert the contact with a lead wire into a plug
connector □ hole until the contact hook
latches on the connector and is secured to
the plug connector. Confirm that the lead
wire cannot be easily pulled out.
To remove it, insert a tool with a fine tip (such
as a small screwdriver) into the rectangular
hole on the side of the plug connector to
push up on the hook, and then pull out the
lead wire.
Cautions: 1. Do not pull hard on the lead wire.It
could result in defective contacts,
breaking wires, etc.
2. If the pin is bent, use a small
screwdriver, etc. to gently
straighten out the pin, and then
complete the connection to the
plug connector.
Attaching and removing plug connector
LED indicator: Red
●AC100V, AC200V
Standard solenoid (Surge suppression)
w or e
Solenoid
Varistor
Use fingers to insert the connector into the
pin, push it in until the lever claw latches
onto the protruded section of the connector
housing, and complete the connection.
To remove the connector, squeeze the lever
along with the connector, lift the lever claw
up from the protruded section of the
connector housing, and pull it out.
e or w
Lead wire: AC100V: Yellow
AC200V: White
Common terminal pre-wired
plug connector
1. Pre-wired common terminal at DC
positive side or AC.
Order code With straight connector: -CPSL
With L connector: -CPLL
Protruded section
Pin
w and e are for with DIN connector (Order code : -39).
（−）（−）（−）（−）（−）（−）
Connector housing
COM（＋）
Crossover wire
Lever
Solenoid with LED indicator
(Surge suppression)
Order code：-PSL, -PLL
Connector
assembly
LED indicator
（Light Emitting Diode）
Lead wire:
AC100V: Yellow
AC200V: White
C
2. Pre-wired common terminal at DC
negative side
Order code With straight connector: -CMSL
With L connector: -CMLL
※Illustration shows the 110 series.
Crimping of connecting lead wire and contact
●DC24V
Tandem solenoid
A
COM
To crimp lead wires into contacts, strip off
4mm [0.16in.] of the insulation from the end
of the lead wire, insert it into the contact,
and crimp it. Be sure to avoid catching the
insulation on the exposed wire crimping
section.
Exposed wire 4mm
Contact
SOL.B
Color of COM, crossover wire
DC12V: Brown
DC24V: Red
AC100V: Yellow
AC200V: White
Polarity is for DC.
Indication
of polarity
Connector （DC）
Contact
Diode
LED indicator: AC100V: Yellow
AC200V: Green
SOL.A
Connector
Connector housing
B
Hock
Lead wire
Equivalent to
AWG22〜26
Insulation crimp tab
Insulation（Maximum
outer diameterφ1.7）
Exposed wire
crimping section
Cautions: 1. Do not pull hard on the lead wire.
2. Always use a dedicated tool for crimping of
connecting lead wire and contact.
Contact: Model 702062-2M
Manufactured by Sumiko Tech, Inc.
Crimping tool: Model F1-702062
Manufactured by Sumiko Tech, Inc.
（＋）（＋）（＋）（＋）（＋）（＋）
COM（−）
Crossover wire
Connector
Connector housing
Color of COM, crossover wire
DC12V: Black
DC24V: Black
Cautions: 1. The diagrams show the straight
connector configuration.
While the connector’s orientation is
different in the case of the L
connector, in every case the first
COM lead wire comes from the last
station’s mounted valve.
2. Since the COM terminal is connected
to a crossover terminal inside the
connector housing, the connector
cannot be switched between a
positive common and a negative
common by changing the connectors.
Manual override
Manual override (Tandem solenoid)
Non-locking type
Locking type
To operate the manual override, press it all the way
down. The single solenoid valve works the same as
when in the energized state as long as the manual
override is pushed down, and returns to the normal
position upon release.
For the double solenoid and twin solenoid valves,
pressing the manual override on the 12(S1) side
switches the 12(S1) to enter the energized position,
and the unit remains in that state even after the
manual override is released. To return it to the
normal position, operate the manual override on the
14(S2) side. This is the same for the solenoid
14(S2).
To lock the locking type manual override, use a
small screwdriver to push down the manual
override in all the way, then set the 0 position as
the reference point and turn it in the clockwise
direction as far as position A. This achieves the
same conditions as when the 14(SA) side is
energized, and the manual override is locked in
place. For the 12(SB) side, turn it in the
counterclockwise direction as far as position B.
To release the lock, return the manual override
to the 0 position. A spring mechanism returns the
manual override to its normal position, and the
lock is released. Care should be taken to avoid
excessive turning of the manual override, which
could damage it.
Cautions: 1. The 110 series valves are internal pilot
type solenoid valves. As a result, the
manual override cannot switch the main
valve without air supplied from the 1(P)
port.
2. Always release the lock of the
locking protruding type manual
override before commencing normal
operation.
3. Do not attempt to operate the manual
override with a pin or other object
having an extremely fine tip. It could
damage the manual override button.
4. Do not turn the adjusting knob more
than needed. It could result in
defective operation.
Mounting base 110-21
PU
A
B
SH
When installing a mounting base to the valve,
always use the provided screws. The recommended tightening torque for the screws is
49N・cm {5kgf・cm} [4.3in・lbf].
※Illustration shows the 110 series.
Mounting valves on manifold
Locking protruding type
When mounting valves on manifold,
apply the recommended tightening torque of
39.2N・cm {4kgf・cm} [3.5in・lbf] for the valve
mounting screws.
Use a small screwdriver to turn the adjusting
knob several times in the clockwise direction,
and lock the manual override in place. When
locked, turning the adjusting knob several times
in the counterclockwise direction releases a
spring on the manual override, returns it to the
normal position, and releases the lock.
For the locking protruding type, when the
adjusting knob is not turned, this type acts just
like the non-locking type, like the valve is the
energized position as long as the manual
override is pushed down, and it returns to the
normal position upon release.
Locking protruding type, locking manual lever type
To lock the locking protruding type manual override
or locking manual lever type, use either a small
screwdriver or your fingertips to push the manual
override button (manual lever) all the way down, then
set the 0 position as the reference point and turn it in
the clockwise direction as far as position A. This
achieves the same conditions as when the 14(SA)
side is energized, and the manual override button
(manual lever) is locked in place. For the 12(SB)
side, turn it in the counterclockwise direction as far
as position B. To release the lock, return the manual
override button (manual lever) to the 0 position. A
spring mechanism returns the manual override
button (manual lever) to its normal position, and the
lock is released. Care should be taken to avoid
excessive turning of the manual override button
(manual lever), which could damage it.
Locking protruding type manual override
※Illustration shows the 110 series.
PU
SH
Cautions: 1. The 110 series valves are internal pilot
type solenoid valves. As a result, the
manual override cannot switch the main
valve without air supplied from the 1(P)
port.
2. Always release the lock of the locking type
and locking protruding type manual override
before commencing normal operation.
3. Do not attempt to operate the manual
override with a pin or other object
having an extremely fine tip. It could
damage the manual override button.
4. Do not turn the adjusting knob more
than needed. It could result in
defective operation.
Locking manual lever type
Handling Instructions and Precautions
(PC Board Manifold)
Solenoid
Plug connector
Circuit configurations
● For positive common type (standard)
Operation example
Lead wire:
＋
Red
Solenoid 1
Lead wire:
Black −
Control signal
01
02
2
＋
8
−
Attaching and removing plug connector
Combination mounting for different type of valves
Use fingers to insert the connector into the
pin, push it in until the lever claw latches
onto the protruded section of the connector
housing, and complete the connection.
To remove the connector, squeeze the lever
along with the connector, lift the lever claw
up from the protruded section of the
connector housing, and pull it out.
In the 110 series manifold for combination
mounting of 2-, 3-, 5-port, and the PC board
manifold for combination mounting of 2-, 3-, 5port, single solenoids can be mounted
together with double solenoids, or with twin
solenoids, and a total number of up to 8 or 16
solenoids can be mounted.
In this case, observe the following precautions:
1. Always use a block-off plate (-BP) to close
the next right station (the side with the
higher numbered station) of the double
solenoid valve mounting station.
2. When using block-off plates (-BP) for some
reason other than item 1, place them together on the higher numbered stations side.
3. Connector pin numbers are allocated to
stations in order from the left end of the
manifold. For a double solenoid mounting,
the upper pins are allocated to 14(S2) and
the lower ones to 12(S1), with the upper
14(S2) numbers being the smaller pin
numbers. And for a twin solenoid mounting,
the left side is allocated to 14(S2) and the
right side allocated to 12(S1), with the left
side 14(S2) numbers being the smaller pin
numbers.
08
Connector
Lever
Indication of polarity
C
Correspondence to sequencer
Dedicated lead wire
for PC board
connection
Output module is negative common type.
Connector
assembly
＋
1
2
3
4
5
6
7
8
01
02
03
04
05
06
07
08
−
COM
Negative common
1 〜 8 : Solenoid
01〜08 : Sequencer output
terminal
Cautions: 1. Do not pull hard on the lead wire.It
could result in defective contacts,
breaking wires, etc.
2. If the pin is bent, use a small
screwdriver, etc. to gently
straighten out the pin, and then
complete the connection to the plug
connector.
●For negative common type (optional: -CM)
Operation example
Lead wire:
Black −
1
Solenoid
2
−
8
＋
−
Lead wire:
Red ＋
Control signal
01
02
Connector housing
Protruded section
Pin
Connector for flat cable
08
Part number
Header
Triangle mark
(first contact
indication)
Socket
Correspondence to sequencer
Example of 4 single solenoid valves and 2
double solenoid valves installation on an 8 unit
manifold:
1
2
3
4
5
7
14（S2）
14（S2）
stn.1 stn.2 stn.3 stn.4 stn.5stn.6 stn.7 stn.8
12（S1）
12（S1）
6
8
Output module is positive common type.
2
3
4
5
6
7
8
01
02
03
04
05
06
07
08
＋
COM
Positive common
Clip
MIL-C-83503 conformity
(made by Sumitomo 3M Ltd.)
1 〜 8 : Solenoid
01〜08 : Sequencer output
terminal
Connector pin location of 8 units:
7
8
5
6
3
4
1
2
Remark: The standard is positive common wiring.
Negative common wiring is optional (-CM).
Manifold
Print circuit board
Avoid using in the locations listed below, as it
may result in deterioration of the print circuit
board or a short circuit in the wiring. If use in
such conditions is unavoidable, always
provide a cover or other adequate protective
measures.
1. Locations subject to high levels of dust or
oil mists
2. Locations subject to salt, corrosive gases,
or conductive particles
3. Locations directly subject to condensation, direct sunlight, or other weather
effects
Example of 3 single solenoid valves and 2
double solenoid valves installation on an 8 unit
manifold:
1
2
3
4
5
6
7
14（S2）12（S1）14（S2）12（S1）
stn.1stn.2 stn.3
stn.4
stn.6
stn.8
Connector pin location of 8 units:
COM
1
COM
−
Flat cable
(equivalent to
AWG28:
MAX 10m
[32.8ft.])
7
5
6
3
4
1
2
Remark: The standard is positive common wiring.
Negative common wiring is optional (-CM).
Made to Order
The 110 series Solenoid Valves include a variety of made to order
solenoids for application in a wider range of control and wiring types.
DIN connector
Plug connector
Straight connector
with LED indicator
L connector
with LED indicator
-39
-PSLN
-PLLN
●Without lead wire
●Connector and contacts included
●Without lead wire
●Connector and contacts included
●When ordering, enter -PSLN or -PSLL in place of the
normal option code for the wiring type.
Lead wire length
A compact connector that is highly resistant to
dust and water splashes.
Employs a self-stripping method that
eliminates the need for de-sheathing the lead
wire.
●When ordering, enter -39 in place of the normal option code for
the wiring type.
●A varistor for surge suppression is also equipped.
(For the AC100V and AC200V only. For DC12V and DC24V, a
flywheel diode for surge suppression is installed as standard
equipment.)
●LED indicator is not available.
Wiring instructions
-1L
-3L
●For plug connector
●Length mm [in.]
-1L：1000 [39]
-3L：3000 [118]
● For lead wire length, -1L is 1000mm [39in.] and -3L is
3000mm [118in.].
When ordering, enter -1L or -3L following the wiring type
option code.
●Solenoid with DIN connector
When de-sheathing (only the outer sheath of the cabtyre), pay attention
to the lead wire direction. The cover will be easily mounted when the
lead wire on the outer side of the terminal cover is set about 8mm
[0.31in.] longer than the inner side.
Without stripping off the sheath, insert the lead until it contacts the lead
wire stopper on the terminal body, and then place the contact from the
upper side. Then use pliers to press the lead wire further to ensure that
the contact is firmly touching the core wire.
JIS C3306
VCTF Conductor 0.75mm2 [0.00116in.2]
Finished outside 6.6mm [0.260in.]（2 leads）
7.0mm [0.276in.]（3 leads）
Cable
1
2
+
3
_
Cable gland
Solenoid terminal
arrangement
Cable gasket
Washer
Contact
Lead wire
stopper
Gasket
Cover mounting
Lead wire
screw Note
Terminal cover
Gasket
Terminal body
Lead wire
Terminal body
Pliers
Note: The appropriate tightening torque for the cover mounting screw is
29.4N • cm {3kgf• cm} [2.6in• lbf].
LED indicator
The LED indicator for confirmation of
operation is also available without a plug
connector. This creates a clean monoblock
look with a compact cover.
-L
●When ordering, enter -L in place of the normal option code for
the wiring type.
●A varistor for surge suppression is also equipped.
(For the AC100V and AC200V only. For the DC12V and
DC24V, a flywheel diode for surge suppression is installed as
standard equipment.)
Built-in interface unit
Includes an interface unit with a photo transistor.
Can be directly controlled by a microcomputer
and logic chip, and is equipped with full electric
noise countermeasures and LED indicators.
Solenoid Specifications for Valve with Built-in Interface Unit
Item
-FA
Input side
●When ordering, enter -FA in place of the normal option code
for the wiring type.
●Cannot be ordered in combination with any other solenoid
option.
●Rated voltages for the solenoid are AC100V and AC200V only.
Specifications
Rated voltage
DC V
5
Voltage range
DC V
4〜6
Operating voltage
DC V
Return voltage
DC V
LED
Interface unit
Zero
cross
circuit
Lead wire:
Black −
＜Solenoid side＞
Solenoid
Condenser
varistor
Rated voltage
Example of control circuits
1. Control by transistor
Vcc
NPN type
90〜125
（100 ＋25
−10 ％）
180〜250
（200 ＋25
−10 ％）
Interface
solenoid valve
Vcc
Current Frequency Hz
when rated Starting mA(r.m.s.)
50
60
50
60
36
32
18
16
Energizing mA(r.m.s.)
24
20
12
10
Leakage Frequency Hz
current
Current mA(r.m.s.)
50
60
50
60
0.3
0.4
0.6
0.8
Surge suppression (as standard)
Built-in varistor on solenoid side
(
)
voltage is
applied
Color of lead wire
Yellow
White
Color of LED indicator (as standard)
Yellow
Green
Voltage resistance
Insulation resistance
Zero-cross function
Wiring type and lead wire length
Min. AC1500V at input side and solenoid side
MΩ
Between input side and
solenoid side, and between
whole terminals and body
Over 100
Available
Grommet type: 300mm [11.8in.]
Wiring instructions
Color of lead wire
Input ― DC0V: Black
Color of lead wire
Input ＋ DC5V: Red
AC100V: Yellow
AC200V: White
Interface
solenoid valve AC100V: Yellow
AC200V: White
AC power
supply
Red
PNP type
Black
2. Control by TTL, IC
Solenoid
side
AC power
supply
Black
200
Shading type
Color of lead wire
Solenoid power supply AC100V: Yellow
Solenoid power supply AC200V: White
Red
100
AC V
Type
Lead wire color:
AC100V: Yellow
AC200V: White
The interface unit is a triac with a photo coupler. Applying DC5V to the
input terminals when AC power is applied on the solenoid side causes
the LED inside the unit to light up, turns on the triac, and energizes the
solenoid. At this time, an LED indicator turns on.
When the input side voltage reaches 0V, the LED inside the unit shuts
off, the triac is turned off, and the solenoid is de-energized. At this time,
the LED indicator is turned off.
With a built-in zero-cross circuit, the zero-cross voltage is used to turn
the power on, and the zero-cross current to turn it off.
0.8 or over
Red (＋), Black (−)
Operating voltage range AC V
Lead wire:
Red ＋
4 or below
Color of lead wire
Block diagram
＜Input side＞
18
Current (when 5V DC is applied) mA
Vcc
Interface solenoid valve
AC power
supply
AC100V: Yellow
AC200V: White
Black
TTL
1. Separate the input side and solenoid side lead wires by color. Never
apply AC power/6VDC or more to the input side.
2. Ensure that voltage ripple on the input side remains within the range
shown below.
Vcc
Interface
solenoid valve AC100V: Yellow
Contact
Red
AC200V: White
AC power
supply
Black
4. When input is not a
DC5V power supply
Vp
Install resistance externally
to drop the input voltage
to 4 〜 6V.
Example
Vp-5-VCE
R1＝
〔Ω〕
18×10-3
Red
AC power
supply
Black
AC100V: Yellow
AC200V: White
VcE R1 Interface
solenoid valve
Vp〔Ｖ〕
R1
12
390Ω1／4W
24
1.0KΩ1W
In the case of VCE = 0〔Ｖ〕
Vm＜6.0V（Vm：Peak voltage）
Vn＞4.0V（Vn：Lowest voltage）
Vn
3. Control by relay contact
Vm
Example : 7406 (able to control up to 2 interface
74LS244
solenoid valves.)
0V
3. Even when a wrong polarity is applied to the input side, a built-in
diode for protection against reverse polarity eliminates any worry
about short circuiting. The valve will not operate, however.
4. A varistor and condensor are built-in in the solenoid power supply
side, for protection circuit against external surge voltages. As a
result, there is a 0.3mA leakage current in AC100V, and a 0.6mA
leakage current in AC200V.
5. The operation and return times of the interface unit are 10ms or less
with a 50Hz AC power supply, and 8ms or less with a 60Hz AC
power supply.
Made to Order
Effective Area
mm2〔Cv〕
For direct piping,
F type manifold
Specifications
Air-piloted valves 110 series
Basic model
For sub-base, A, AJ type manifolds
110-4A, 110-4A2
Single valve
(When mounted on the AJ type
4(A), 2(B) ports
Built-in quick fit- -J42 with fittings
ting for φ 4 tube -J43 1(P), 4(A), 2(B)
ports with fittings
●The ideal air valve for master valves or pilot
valves for total pneumatic control.
A110-4A, A110-4A2
4.0〔0.22〕
4.2〔0.23〕
4(A), 2(B) ports
-J62 with fittings
Built-in quick fitting for φ 6 tube -J63 1(P), 4(A), 2(B)
ports with fittings
3.6〔0.20〕manifold with -J4 specification)
3.6〔0.20〕
─
─
(When mounted on the AJ type
4.0〔0.22〕manifold with -J4 specification)
─
─
● Attaching TS4-M5 to the 1(P), 4(A), ● Attaching TS4-01 to the 1(P), 4(A),
2(B) ports gives the value 1.8〔0.1〕.
2(B) ports on the sub-base (-25)
gives the value 3.2〔0.18〕
.
● On the F type manifold, attaching
TS4-M5 to the 4(A), 2(B) ports gives
the value 2.1〔0.12〕.
● When large flow rates are required,
we recommend the built-in quick
fittings.
Remarks
Specifications
Port Size
For direct piping, F type manifold For sub-base, A, AJ type manifolds
Single pilot
Double pilot
Single pilot
Double pilot
Item
Basic model
110-4A
110-4A2
A110-4A
A110-4A2
Media
Air
Operation type
Air-piloted type
Number of positions and ports
2 positions, 5 ports
Effective area〔Cv〕 mm2
4.2〔0.23〕Note 1
Main
M5×0.8 Note 2
─ Note 2
Port size
Pilot
M5×0.8
Lubrication
Not required
0.15〜0.7 {1.5〜7.1} 0〜0.7 {0〜7.1}
Operating pressure Main 0.15〜0.7 {1.5〜7.1} 0〜0.7 {0〜7.1}
[0〜102]
[22〜102]
[0〜102]
[22〜102]
range
2
MPa {kgf/cm } [psi.] Pilot
See the table “Minimum Pilot Pressure”
1.05 {10.7 } [152]
Proof pressure MPa {kgf/cm2} [psi.]
Operating temperature range
5〜60 [41〜140]
(atmosphere and media) °C [°F]
Shock resistance m/s2{G}
Mounting direction
Maximum operating frequency Hz
Mass
g [oz.]
1373.0 {140.0} (Axial direction 294.2 {30.0})
Any
5
45 [1.59] (140 [4.94]) Note 3 50 [1.76] (145 [5.11]) Note 3
40 [1.41]
45 [1.59]
Notes: 1. For details, see the effective area.
2. For details, see the port size.
3. Figures in parentheses ( ) are the mass with sub-plate: -25.
※ For optional specifications and order codes, see p.301〜302.
Manifold Specifications and Port Size
Manifold model
Specifications
F type
P, R manifold piping
A, B valve piping
A type
All ports manifold piping
AJ type
A, B ports built-in quick fittings
All ports manifold piping
For direct piping,
F type manifold
Basic model
For sub-base,
A, AJ type manifolds
Remarks
110-4A
A110-4A
110-4A2
A110-4A2
Port
（
1 P）
Female
Standard
（
4 A）
,2（B）
M5×0.8
─
thread
（
3 R2）,5（R1）
M5×0.8
（
1 P）
●Straight type
-J42 （
4 A）
,2（B） Built-in quick fitting
Built-in
●For φ 4 tube
（
3 R2）,5（R1）
M5×0.8
quick
─
●For both nylon
（
1
P）
Built-in
quick
fitting
tubes and
fitting
-J43 （
4 A）
,2（B）
urethane tubes
（
3 R2）,5（R1）
M5×0.8
（
1 P）
Sub-base
●All ports sub-base
（
4 A）
,2（B）
─
Rc1/8
-25
piping
（
3 R2）,5（R1）
（
1 P）
Rc1/8
●1(P), 3(R2) , 5(R1)
F type
（
4 A）
,2（B） M5×0.8 or quick fitting
─
manifold,
manifold
4(A), 2(B) valve piping
Rc1/8
（
3 R2）,5（R1）
（
1 P）
Rc1/8
A type
●All ports manifold
（
4 A）
,2（B）
─
manifold
piping
3, （
5 R）
Rc1/4
（
1 P）
Rc1/4
●All ports manifold piping
Built-in quick fitting ●4(A), 2(B) ports
-J4
AJ type
（
4 A）,2（B）
─
manifold
Built-in quick fitting -J4 : For φ 4 tube
-J6
-J6 : For φ 6 tube
3, （
5 R）
Rc1/4
Specifications
Port
1
（P）
4
（A）
,2
（B）
3
（R2）
,5
（R1）
1
（P）
4
（A）
,2
（B）
3, 5
（R）
1
（P）
-J4
4
（A）
,2
（B）
-J6
3, 5
（R）
Port size
Rc1/8
M5×0.8 or quick fitting (Valve order code: -J42)
Rc1/8
Rc1/8
Rc1/8
Rc1/4
Rc1/8
Quick fitting for φ 4 tube
Quick fitting for φ 6 tube
Rc1/4
※ For optional specifications and order codes, see p.302.
Manifold Mass
g [oz.]
Manifold
model
Mass calculation of each unit
(n=number of units)
F type
A type
(20×n)＋30 [(0.71×n)＋1.06]
(60×n)＋60 [(2.12×n)＋2.12]
(67×n)＋60 [(2.36×n)＋2.12]
(64×n)＋60 [(2.26×n)＋2.12]
AJ
type
-J4
-J6
Mounting valve
110-4A 110-4A2 A110-4A A110-4A2
40 [1.41] 45 [1.59]
─
─
─
─
Minimum Pilot Pressure
Main pressure
Model
110-4A
110-4A2
0.15 {1.5} [22] 0.3 {3.0} [44]
MPa {kgf/cm2} [psi.]
0.5 {5.1} [73] 0.7 {7.1} [102]
0.15 {1.5} [22] 0.25 {2.5} [36] 0.34 {3.5} [49] 0.45 {4.5} [65]
0.08 {0.8} [12] 0.10 {1.0} [15] 0.12 {1.2} [17] 0.14 {1.4} [20]
45 [1.59] 50 [1.76]
Calculation example: The mass of 110M 10F stn.1〜5 110-4A, stn.6〜10 110-4A2
becomes (20×10)＋30＋(40×5)＋(45×5)=655g [23.10 oz.]
Required Time for Switching
Model
110-4A
A110-4A2
Operation
2 [6.6]
S
Pilot line length L m [ft.]
6 [19.7] 10 [32.8] 20 [65.6] 50 [163.9] 100 [327.8]
ON
0.06
0.14
0.26
0.63
2.30
6.54
OFF
0.12
0.33
0.67
1.65
6.30
19.50
0.07
0.16
0.29
0.70
2.66
7.40
Measurement conditions
L
Pilot valve（B port plug）
L
ON
OFF
Measurement circuit
Pilot valve
●Pilot valve=050-4E1 (effective area1.2mm2
)
〔Cv: 0.067〕
●Tube inner diameter = 4mm [0.16in.]
●Air pressure (both main and pilot)=0.5MPa
[73psi.]
〔 Cv〕
〕
Effective Area〔
Basic model
mm2〔Cv〕
Standard (Single valve)
Built-in quick fittings
4.2
〔0.23〕
-J4□ : 3.6〔0.20〕
-J6□ : 4.0〔0.22〕
3.8
〔0.21〕
-J4□ : 3.4〔0.19〕
-J6□ : 3.6〔0.20〕
A111E1Note
(A110E1)
A110-4E1
A110-4E2
A110-4KE2
A110-4ME2
4.0
〔0.22〕
-J4□ : 3.6〔0.20〕
-J6□ : 4.0〔0.22〕
A113-4E2
A113-4KE2
A113-4ME2
3.6
〔0.20〕
3.6
〔0.20〕
111E1Note
(110E1)
110-4E1
110-4E2
110-4KE2
113-4E2
113-4KE2
Remarks
●When attaching TS4-M5 to the 1(P), 4(A), 2(B) ports, the value is 1.8〔0.10〕.
●On the F type manifold, attaching TS4-M5 to the 4(A), 2(B) ports gives the
value 2.1
〔0.12〕.
●When large flow rates are required, we recommend the φ6 built-in quick
fitting.
●When mounting on a sub-base or manifold.
●Attaching TS4-01 to the 1(P), 4(A), 2(B) ports on the sub-base gives the value
3.2〔0.18〕.
Note: The delivery port is the 2(A) for 111E1, A111E1.
Solenoid Valve Port Size
Basic model
Port specification
Standard
111E1Note1
(110E1Note2)
M5×0.8
-J41
Quick fitting for φ4, for 2(A) (4(A)) port only
Optional
Standard
110-4E1
110-4E2
110-4KE2
113-4E2
113-4KE2
-J42
Quick fitting for φ4, for 1(P), 2(A) ports
-J61
Quick fitting for φ6, for 2(A) (4(A)) port only
-J62
Quick fitting for φ6, for1(P), 2(A) ports
Female thread
M5×0.8
-J42
Quick fitting for φ4, for 4(A), 2(B) ports only
-J43Note 3
Quick fitting for φ4, for 1(P), 4(A), 2(B) ports
Optional
A111E1-25Note1
A110-4E1-25
A110-4E2-25
A113-4E2-25
A110-4ME2-25
A113-4ME2-25
Port size
Female thread
-J62
Quick fitting for φ6, for 4(A), 2(B) ports only
-J43Note 3
Quick fitting for φ6, for 1(P), 4(A), 2(B) ports
Female thread
Rc1/8
Female thread
M5×0.8
1（P）
4（A）, 2（B）
3（R2）, 5（R1）
PR
Notes: 1. The delivery port is the 2(A) for 111E1, A111E1-25.
2. Since 110E1 is for manifold use only, piping to the 1 (P) port with a fitting is not possible.
3. Not available in 110-4E2, 113-4E2, 110-4KE2, and 113-4KE2.
Manifold Connection Port Size
Port
Location of piping ports
1（P）
Manifold
Rc1/8
4（A）, 2（B）
Valve
M5×0.8 Note2
3（R）, 3（R2）, 5（R1）
Manifold
Rc1/8
1（P）
Manifold
Rc1/8
4（A）, 2（B）
Valve
M5×0.8
Manifold model
111M□FNote1
110M□F
110M□FE
3（R2）, 5（R1）
Port size
Rc1/8
Manifold
PR
M5×0.8
1（P）
111M□ANote1
4（A）, 2（B）
110M□A
3（R）, 3, 5（R）
Rc1/8
Manifold
Rc1/8 (111M□A), Rc1/4 (110M□A)
PR
111M□AJNote1
110M□AJ
M5×0.8
1（P）
Rc1/8
4（A）, 2（B）
Quick fitting for φ4 or φ6
Manifold
3（R）, 3, 5（R）
Rc1/8 (111M□AJ), Rc1/4 (110M□AJ)
PR
M5×0.8
Notes: 1. The delivery port is the 2(A) for 111M□F, 111M□A, 111M□AJ.
2. When the mounting valve is a female thread specification, the ports are this size. For the built-in quick fitting types, quick fittings for φ4 or φ6 are
installed.
Solenoid Valve Mass
Basic model
111E1
(110E1)
110-4E1
110-4E2
110-4KE2
113-4E2
113-4KE2
A111E1
(A110E1)
A110-4E1
A110-4E2
A110-4KE2
A110-4ME2
A113-4E2
A113-4KE2
A113-4ME2
Remark: Figures in parentheses（
g [oz.]
Mass
75 [2.65]
80 [2.82]
80 [2.82]
125 [4.41]
175 [6.17]
145 [5.11]
165 [5.82]
80 [2.82] (180 [6.35])
85 [3.00]
85 [3.00] (180 [6.35])
130 [4.59] (225 [7.94])
180 [6.35]
110 [3.88] (205 [7.23])
150 [5.29] (245 [8.64])
170 [6.00]
120 [4.23] (215 [7.58])
）are the mass with sub-base:-25
Manifold Mass
Manifold model
g [oz.]
Mass calculation of each unit
（n＝number of units）
Block-off plate
5 [0.18]
111M□F
(15×n)＋30
[(0.53×n)＋1.06]
111M□A
(45×n)＋45
[(1.59×n)＋1.59]
111M□AJ
-J4 : (53×n)＋45 [(1.87×n)＋1.59]
-J6 : (50×n)＋45 [(1.76×n)＋1.59]
10 [0.35]
6 [0.21]
110M□F
(20×n)＋30
[(0.71×n)＋1.06]
110M□FE
(40×n)＋50
[(1.41×n)＋1.76]
110M□A
(60×n)＋60
[(2.12×n)＋2.12]
110M□AJ
-J4 : (67×n)＋60 [(2.36×n)＋2.12]
-J6 : (64×n)＋60 [(2.26×n)＋2.12]
11 [0.39]
SOLENOID VALVES
SERIES
Basic Models and Valve Functions
Basic model Direct piping,
F, FE type
manifolds
Sub-base piping,
A, AJ type
manifolds
Item
111E1
(110E1Note)
110-4E1
110-4E2
A111E1
(A110E1Note)
A110-4E1
A110-4E2
A110-4ME2
2 positions
Number of positions
Number of ports
2, 3 ports
Valve function
Normally closed (NC, standard)
or
Normally open (NO, optional)
110-4KE2Note
113-4E2
113-4KE2
A110-4KE2Note
A113-4E2
A113-4ME2
A113-4KE2
3 positions
5 ports
Single solenoid,
Double solenoid
or
Tandem solenoid
Twin solenoid
Closed center (standard),
Exhaust center (optional),
Pressure center (optional)
or Tandem solenoid
Closed center (standard),
Exhaust center (optional),
Pressure center (optional)
or Twin solenoid
Remark : For optional specifications and order codes, see p.300〜302.
Note : The 110E1, A110E1, 110-4KE2, and A110-4KE2 are dedicated valves for manifolds with combination mounting of 2-, 3-, 5-port valves. They cannot be used
as single units. When using 2-,3-port valves as single units, use 111E1 or A111E1-25.
Specifications
Basic model Direct piping,
F, FE type
manifolds
Sub-base piping,
A, AJ type
manifolds
Item
111E1
(110E1)
110-4E1
110-4E2
110-4KE2
A111E1
(A110E1)
A110-4E1
A110-4E2
A110-4KE2
A110-4ME2
113-4E2
113-4KE2
A113-4E2
A113-4KE2
A113-4ME2
Air
Media
Operation type
Internal pilot type
Effective area〔Cv〕Note1
mm2
4.2〔0.23〕
4.0〔0.22〕
3.8〔0.21〕
3.6〔0.2〕
Ｍ5×0.8
Port sizeNote 2
Lubrication
Not required
Operating pressure range MPa {kgf/cm2} [psi.]
Proof pressure MPa {kgf/cm2} [psi.]
Response
DC12V, DC24V
ms
time Note 3
AC100V, AC200V
ON/OFF
Maximum operating frequency
Hz
0.15〜0.7 {1.5〜7.1} [22〜102]
1.05 {10.7} [152]
15/25 or below
15/25〔20〕or below
15 or below
15/15 or below
15/15〔15〕or below
─
─
5
─
Minimum time to energize for self holding ms
50(□110-4E2)
50
Operating temperature range (atmosphere and media) °C [°F ]
─
5〜50 [41〜122]
m/s2 {G}
Shock resistance
15/30 or below
15/20 or below
294.2 {30.0}
1373.0 {140.0} (Axial direction 294.2 {30.0} )
Mounting direction
Any
Notes : 1. For details, see the effective area on p.298.
2. For details, see the port size on p.298.
3. Values when air pressure is 0.5MPa {5.1kgf/cm2} [73psi.]. Values in brackets〔 〕for 110-4E2, 110-4KE2, and 110-4ME2 are when switching from the
opposite position, while the values for 113-4E2, 113-4KE2, and A113-4ME2 are those of the closed center valve, when switching from the neutral position.
Solenoid Specifications
Rated voltage
Item
DC12V
AC100V
Flywheel diode incorporated
for surge suppression
Type
10.8〜13.2
（12±10％）
Operating voltage range
Ｖ
Frequency
Hz
─
mA (r.m.s)
─
Current
(when
rated
voltage is
applied)
DC24V
Starting
Energizing mA (r.m.s)
Allowable leakage current
mA
Insulation resistance
MΩ
21.6〜26.4
（24±10％）
140 (1.7W)
Color of LED indicator
Surge suppression (as standard)
Built-in surge
absorption transistor
Shading type
180〜264
（200＋32
−10 ％）
─
50
60
50
60
─
─
36
32
18
16
─
24
20
12
10
50（1.2W）
75 (1.8W)
〔 with LED indicator 〕
〔 with LED indicator 〕
8
4
4
2
21.6〜26.4
（24±10％）
2
Over 100
Wiring type Standard
and lead
wire length Optional
Color of lead wire
DC24V (Tandem solenoid)
90〜132
（100＋32
−10 ％）
65（1.6W）
130（1.6W）
AC200V
Grommet type: 300mm [11.8in.]
Plug connector type: 300mm [11.8in.]
Plug connector type: 300mm [11.8in.]
Note: See made to order on p.315〜316.
─
Red（＋）
Black（−）
Brown（＋）
Black（−）
Red
Flywheel diode
Yellow
White
Yellow
Green
Varistor
Red (SA), Black (COM)
White (SB)
Red
Surge absorption transistor
■Cylinder Operating Speed
How to obtain cylinder speed
Cylinder stroke
To obtain the time required for the cylinder to complete 1 stroke, add
cylinder’s delay time t1 (time between energizing of solenoid valve and
actual starting of the cylinder), to the cylinder’s max. speed operating
time t2.
When a cushion is used, add the cushioning time t 3, to the above
calculation. The standard cushioning time t 3 is approximately 0.2
seconds.
Cushioning
impact
Cylinder start
t3
Time
Cylinder stop
t2
Solenoid valve
energized
t1
110-4E1
113-4E2
A110-4E1-25
A113-4E2-25
A110-4ME2
A113-4ME2
●Measurement conditions
●Measurement conditions
●Measurement conditions
●Air pressure : 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length : φ2.5 [0.10in.]×
1000mm [39in.]
●Fitting : Quick fitting TS4-M5
Load
Load
●Load ratio =
(%)
Cylinder theoretical thrust
●Cylinder stroke : 150mm [5.91in.]
●Air pressure : 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length : φ4 [0.16in.]×
1000mm [39in.]
●Fitting : Quick fitting TS6-01
Load
●Load ratio =
(%)
Cylinder theoretical thrust
Load
●Cylinder stroke : 150mm [5.91in.]
Solenoid valve
A110-4E1-25
A113-4E2-25
●Air pressure : 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length : φ4 [0.16in.]×
1000mm [39in.]
●Fitting : Quick fitting TS4-01
Load
Load
●Load ratio =
(%)
Cylinder theoretical thrust
●Cylinder stroke : 150mm [5.91in.]
Fitting TS4-M5
Maximum operating speed
Fitting TS6-01
Maximum operating speed
200
10
20
30 40 50
Load ratio
60
1000
800
600
φ20 [0.787in.]
φ25 [0.984in.]
φ32 [1.260in.]
φ40 [1.575in.]
φ50 [1.969in.]
400
200
0
70
%
mm/s
1200
10
20
1mm/s = 0.0394in./sec.
s
10
20
30 40 50
Load ratio
60
Delay time
Delay time
Delay time
Delay time
φ40 [1.575in.]
φ32 [1.260in.]
φ25 [0.984in.]
φ20 [0.787in.]
60 70
%
1000
800
600
φ20 [0.787in.]
φ25 [0.984in.]
φ32 [1.260in.]
φ40 [1.575in.]
400
200
0
10
20
30 40 50
Load ratio
1mm/s = 0.0394in./sec.
s
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
30 40 50
Load ratio
Maximum operating speed
φ20 [0.787in.]
φ25 [0.984in.]
φ32 [1.260in.]
φ40 [1.575in.]
400
0
Maximum operating speed
s
φ50 [1.969in.]
φ40 [1.575in.]
φ32 [1.260in.]
φ25 [0.984in.]
φ20 [0.787in.]
10
70
%
Delay time
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
70
%
60
1mm/s = 0.0394in./sec.
20
30 40 50
Load ratio
60
Delay time
600
Maximum operating speed
Maximum operating speed
800
0
Fitting TS4-01
mm/s
1200
mm/s
1200
1000
Cylinder
0.5MPa
0.5MPa
0.5MPa
Cylinder
Cylinder
Solenoid valve
110-4E1
113-4E2
70
%
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
φ50 [1.969in.]
φ40 [1.575in.]
φ32 [1.260in.]
φ25 [0.984in.]
φ20 [0.787in.]
10
20
30
40
50
60
Load ratio
70
%
0.6
Supply pressure
0.7 （MPa）
0.6
111E1
0.5
0.5
0.4
0.3
0.2
0.1
0
0.4
0.3
0.2
0.1
100
200 300 400
Flow rate R/min(ANR)
(110E1)
110-4E1
110-4E2
110-4KE2
A111E1
(A110E1)
A110-4E1
A110-4E2
A110-4KE2
MPa
0.7
0.6
Supply pressure
（MPa）
0.5
0.4
0.3
0.2
0.1
0
0.2
0.7
0.6
0.5
0.4
0.3
0.1
113-4E2
113-4KE2
A113-4E2
A113-4KE2
100
200 300 400
Flow rate R/min(ANR)
MPa
0.7
Valve outlet pressure
0.7
Valve outlet pressure
MPa
Valve outlet pressure
■Flow Rate
0.6
0.7
0.6
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.2
0.1
0.1
0
Supply pressure
（MPa）
A110-4ME2
A113-4ME2
100
200 300 400
Flow rate R/min(ANR)
How to read the graph
1MPA = 145psi.
1R/min = 0.0353ft.3/min.
When the supply pressure is 0.5MPa [73psi.]
and the flow rate is 180R/min [6.35ft.3/min.]
(ANR), the valve outlet pressure becomes
0.4MPa [58psi.].
110 Series Tandem Solenoid Valve Order Codes
■3-position valve
●Solenoid
valves
※ Single solenoid, double solenoid, twin solenoid, and tandem solenoid valves can
be mounted together on the manifold.
■Sub-base
■Manual override
Without sub-base ：Blank
With sub-base
：-25
Valve function
Closed center ： Blank
Exhaust center ： -13
Pressure center ： -14
■Wiring type
Locking type：-81
Locking protruding type：-83
Locking manual lever type：-84
Straight connector
with LED indicator：-PSL
L connector
with LED indicator：-PLL
Basic model
5-port
double
solenoid
Sub-base
piping
Voltage
A110-4ME2
-81
-83
-84
-25
5-port
3-position
A113-4ME2
-13, -14
-PSL
-PLL
DC24V
Note : They cannot be used as single units.
●Always select one from each group.
■Manual override
■3-position valve
●Manifold
Manifold model
Number of units
Manifold for
combination mounting
of 2-, 3-, 5-port valves
110M
2
⁝
20
Station
A
AJ
■Wiring type
Locking type：-81
Locking protruding type：-83
Locking manual lever type：-84
Valve function
Closed center ： Blank
Exhaust center ： -13
Pressure center ： -14
Straight connector
with LED indicator：-PSL
L connector
with LED indicator：-PLL
■Manifold
Connection port
Quick fitting for φ4 tube：-J4
Quick fitting for φ6 tube：-J6
Basic model
Stn.□
⁝
Stn.□
Voltage
-A110-4ME2
-A113-4ME2
●Valve mounting location from the
left-hand side when facing the
4(A), 2(B) ports.
-13, -14
-81
-83
-84
●Specify the valve model
for each station.
●Enter -BP when closing a
station with a block-off
plate without mounting a
valve.
-PSL
-PLL
-J4
-J6
●Always select
one from each
group.
DC24V
●For the AJ type
manifold only, specify
either of the two.
Options
■Wiring type
■Manual override
Straight connector
with LED indicator
L connector
with LED indicator
-PSL
-PLL
Locking type
■AJ type manifold
Locking protruding
type
-81
-83
Locking
manual lever type
-84
Additional Parts (To be ordered separately)
Made to Order
Speed controller
Lead wire length
● For sub-base
piping
Quick fitting
for φ6 tube
-J4
-J6
●Select the tube size for each station.
●Lead wire length
300mm
SCE-01
Quick fitting
for φ4 tube
Muffler
Block-off plate
-1L
-3L
KM-11
● For sub-base
piping
● 110 MA-BP
110−For 110M
●For plug connector
●Length -1L：1000 [39in.]
(mm) -3L：3000 [118in.]
110 Series Solenoid Valve, Air-piloted Valve Order Codes
■Port fitting specifications Note 2
■2-, 3-port valve ■2-, 3-port valve ■3-position valve ■Sub-base
Number of ports Valve function
Valve function
Female thread：
Normally closed
(NC)
3-port
A
P
A
Closed center
P
4（A）
R
Blank
Blank
●Lead wire length:
300mm [11.8in.]
is standard.
Blank
-J41,-J42,-J43 : Quick fitting for φ4 tube
-J61,-J62,-J63 : Quick fitting for φ6 tube
Non-locking type
1（P）
3（R2）
Blank
-J41
-J61
Blank
-J42
-J62
Blank
● 2(A) port of 111E1 ●1(P), 2(A) ports
(4(A) port of 110E1)
of 111E1
Normally open (NO) Exhaust center
2-port
P
A
A
P
4（A）
Blank
Locking protruding Straight connector
type
with LED indicator
With sub-base
5（R1）
1（P）
2（B）
R
-2
Grommet type
5（R1）
2（B）
R
Without sub-base
■Manual override■Wiring type
3（R2）
-11
-13
-J42
-J62
-25
●4(A), 2(B) ports
of 5-port
-J43
-J63
-83
●1(P), 4(A), 2(B)
ports of 110-4E1
L connector
with LED indicator
Pressure center
4（A）
-PSL
5（R1）
1（P）
2（B）
3（R2）
-14
-PLL
Basic model
2-, 3-port
Direct piping
5-port
single solenoid
5-port
double solenoid
5-port
3-position
2-, 3-port
5-port
single solenoid
Sub-base piping
5-port
double solenoid
5-port
3- position
2-, 3-port
for 110M□F, FE
5-port, 2-position
for 110M□F, FE
For manifold with
5-port, 3-position
combination
for 110M□F, FE
mounting of 2-, 3-,
2-, 3-port
5-port valves
for 110M□A, AJ
only Note 1
5-port, 2-position
for 110M□A, AJ
5-port, 3-position
for 110M□A, AJ
5-port
Direct piping
single pilot
air-piloted valve
5-port
(made to order)
double pilot
5-port
Sub-base piping
single pilot
air-piloted valve
5-port
(made to order)
double pilot
111E1
Voltage
-2
-11
110-4E2
-2
SCE-M5
-2
-83
-PSL
-PLL
DC12V
DC24V
AC100V
AC200V
-J41
-J61
-11
110-4KE2
-J42
-J62
-13
-14
113-4KE2
-2
-11
A110-4KE2
-13
-14
A113-4KE2
110-4A
-J42,-J43
-J62,-J63
110-4A2
-J42
-J62
A110-4A
-25
A110-4A2
Notes : 3. Side mounting of valve is not possible when -J41, -J42, -J43, -J61, -J62, or -J63 is
Muffler
SCE-01
DC12V
DC24V
AC100V
AC200V
-13
-14
A113-4E2
Additional Parts (To be ordered separately)
●For direct piping ● For sub-base
piping
-83
-PSL
-PLL
Note 4
-25
A110-4E2
A110E1
DC12V
DC24V
AC100V
AC200V
-11
A110-4E1
110E1
-J42
-J62
-13
-14
113-4E2
A111E1
-83
-PSL
-PLL
-J42,-J43 Note 3
-J62,-J63
110-4E1
Notes : 1. They cannot be used as single units.
2. The port fittings are for φ4: TSK4-M8M, and for φ6:
TSK6-M8M.
Speed controller
-J41,-J42 Note 3
-J61,-J62
KM-05
selected, because in these cases there are no mounting holes on the valve side
surface.
4. Mounting on the manifold only is possible when -J42 or -J62 is selected for the
110-4E2 or 113-4E2, because in these cases they do not have mounting holes.
Mounting base
Block-off plate
KM-11
110-21
●For direct piping ● For sub-base
piping
●For direct piping
●For 2-, 3-port
and 5-port
single solenoids
●
M
-BP
111 − For 111M
110 − For 110M
F — For F type manifold
FE — For FE type manifold
A — For A type, AJ type manifolds
110 Series Manifold Order Codes
■2-, 3-port valve ■2-, 3-port valve ■3-position valve ■Port fitting
■Manual override ■Wiring type
Number of ports Valve function
Valve function
specifications Note 2
●Lead wire length:
Female Blank
300mm [11.8in.] is standard.
Normally closed
（NC)
3-port
A
P
A
Closed center
P
4（A）
5（R1）
R
Blank
Blank
Blank
P
4（A）
-J4
Blank
Straight connector
with LED indicator
Quick fittings
for φ6 tube
L connector
with LED indicator
5（R1）
1（P）
2（B）
R
-2
Blank
Locking protruding
● 2(A) port of 111E1 type
(4(A) port of 110E1)
Exhaust center
P
A
A
3（R2）
-J41
-J61
Normally open
（NO)
2-port
Quick fittings
for φ4 tube
Grommet type
1（P）
2（B）
R
thread：
-J41,-J42 :
Quick fitting forφ4 tube Non-locking type
-J61,-J62 :
Quick fitting for φ6 tube
■Manifold
Connection port
3（R2）
-11
-13
-83
-PSL
-J42
-J62
Pressure center
4（A）
-PLL
Straight connector
with LED indicator
●4(A), 2(B) ports of
5-port
-J6
L connector
with LED indicator
5（R1）
1（P）
2（B）
3（R2）
-CPSL
-CMSL
-14
-CPLL
-CMLL
●-CP□L : DC12V and DC24V positive
side, and AC100V, AC200V.
●-CM□L : DC12V and DC24V negative side.
Manifold for mounting 5-port valve
(made to order)
Manifold for combination mounting of 2-, 3-, 5-port valves
Manifold
for 2-, 3-port
valves
Manifold model
Number of units
111M
2
⁝
20
Station
F
A
AJ
stn.□
⁝
stn.□
Basic model
Voltage
-111E1
-2
-11
-A111E1
-2
-11
-110E1
-2
-11
-J41
-J61
-83
-PSL
-PLL
-CPSL
-CMSL
-CPLL
-CMLL
-83
-PSL
-PLL
-CPSL
-CMSL
-CPLL
-CMLL
-83
-PSL
-PLL
-CPSL
-CMSL
-CPLL
-CMLL
-J41
-J61
-110-4E1
F 注1
FENote1
stn.□
⁝
stn.□
-110-4E2
-J42
-J62
-110-4KE2
-113-4E2
110M
2
⁝
20
-13
-14
-113-4KE2
-A110E1
-2
A
AJ
-13
-14
-A113-4KE2
110M
2
⁝
20
F
A
AJ
stn.□
⁝
stn.□
stn.□
⁝
stn.□
-110-4A
-A110-4A
DC12V
DC24V
AC100V
AC200V
-J4
-J6
-A110-4A2
Notes : 1. Since the PR port on the port fitting type valves is located on the opposite side
from the manifold, pilot air is exhausted directly from the valve. For that
reason, collective exhaust is not possible and the port fitting type valves
cannot be used for the manifold.
2. Fitting used for port fitting specifications, φ4: TSK-M8M, φ6: TSK6-M8M.
-J4
-J6
-J42
-J62
-110-4A2
●Valve mounting location from the left-hand side when facing the 4(A), 2(B)
ports.
●Since a twin solenoid valve requires 2 stations per valve to mount, the
second station (solenoid 12(S1) side) should be blank.
DC12V
DC24V
AC100V
AC200V
-11
-A110-4E1
stn.□ -A110-4E2
⁝
stn.□ -A110-4KE2
-A113-4E2
-J4
-J6
DC12V
DC24V
AC100V
AC200V
●Specify the valve model for each station. ●Specify only for
F type manifolds.
●Enter -BP when closing a station with
a block-off plate without mounting a
valve.
●For the AJ type manifold only,
specify either of the two.
●It is not required when
ordering a single valve unit.
●Pre-wired common terminal
for AC100V and AV200V is
either -CPSL or -CPLL.
110 series includes made to order items of various kinds for further system development.
Made to Order The
For details, see p.315〜317.
Straight connector
with LED indicator
L connector
with LED indicator
Lead wire length
-PSLN
-PLLN
-1L
-3L
●Without lead wire
●Connector,
contacts included.
●Without lead wire
●Connector,
contacts included.
●For plug connector
●Length (mm)
-1L：1000 [39in.]
-3L：3000 [118in.]
DIN connector
-39
●Cannot be used
with -L.
LED indicator
with built-in varistor
-L
●Cannot be used
with -39.
Built-in interface
unit
Air-piloted valves
110 series
-FA
●Possible to be directly
controlled by output
from micro computer
or other logic devices.
●With LED indicator
●5-port, 2-position
●Single pilot
●Double pilot
Operating Principles and Symbols
3-port
Normally
closed (NC)
2（A）
Normally
open (NO)
1（P）
3（R）
111E1
Solenoid cover
2（A）
1（P）
3（R）
111E1-11
De-energized
Column
De-energized
Molded solenoid
Shading coil
（AC solenoid only）
Plunger spring
Plunger pin
Plunger
Major Parts and Materials
Flapper
Manual override
Parts
Pilot valve body
PR
Materials
Body
PR
Aluminum alloy
（anodized）
Stem
Piston
3（R）
Lip seal
2（A）
2（A）
1（P）
1（P）
Body
Lip seal
3（R）
Valve
Synthetic rubber
Flapper
Mounting base Mild steel (zinc plated)
Sub-base
Aluminum alloy (anodized)
Stem
Plunger
End cover
Column
Magnetic stainless
steel
Body
Aluminum alloy (anodized)
Manifold
Block-off plate Mild steel (nickel plated)
Seal
5-port, 2-position
Synthetic rubber
5-port, 3-position
Single solenoid
Double solenoid
Twin solenoid
Closed center
14（S2）
14（S2）
4（A）
2（B）
5（R1）
1（P）
3（R2）
4（A）
2（B）
4（A）
2（B）
5（R1）
1（P）
3（R2）
5（R1）
1（P）
3（R2）
12（S1）
12（S1）
110-4E1
110-4E2
(
De-energized
110-4KE2
)
De-energized condition
after energizing solenoid 12(S1)
(
14（S2）
PR
113-4E2
14（S2）
14（S2）12（S1）
14（S2）12（S1）
PR1
PR1
5（R1）
4（A）
5（R1）
4（A）
1
（P）
2（B）
1
（P）
2（B）
3
（R2）
113-4KE2
)
De-energized condition
after energizing solenoid 12(S1)
3
（R2）
PR2
12（S1）
5（R1）
4（A）
1（P）
2（B）
4（A）
2（B）
5（R1）
1（P） 4（A）
3（R2）
5
（R1）
1（P）
2（B）
3（R2）
3
（R2）
PR2
12（S1）
Dimensions of Solenoid Valve, 2-, 3-port (mm)
A111E1
A111E1-25
30
24
15
3
2-φ3.2
Mounting hole
10
42
46.5
︵
︶
︵
2 A
10
18
10
18
3
5.5
25
32.2
74.7
1（P）
15.5
25.5
11.5 14
20.5
A
2（A）
1P
︶
0.5
5.5
3-Rc1/8
50
24
Manual override
Non-locking type: Standard
Locking protruding type: -83
20
10
PR
2（A）
M5×0.8
3R
46.5
12.5 12
2-φ2.8 Counterboreφ5.4 Depth 3
Mounting hole
PR
2-φ3.2
Mounting hole
3（R）
38
26
74.7
3-M5×0.8
3
︵
Manual override
Non-locking type: Standard
Locking protruding type: -83
Approximately
300
︶
Approximately
24
300
15
20
111E1
111E1
〈Viewed from A〉
9 9
2-M2.6×0.45 Depth 3
Mounting thread
3（R）
4.5
4.5
1（P）
3
Additional Parts (To be ordered separately)
110-BASE
79.7
（ To the top surface of
the valve）
5
●Mounting base : 110-21
110-MUFF
●Muffler
For direct piping：KM-05
110-SC
●Speed controller
For sub-base piping：KM-11
For direct piping：SCE-M5
For sub-base piping：SCE-01
9.2
M5×0.8
2-φ4.5
Mounting hole
8
Width across flats
M5×0.8
14
Width across flats
24
（21）
16.5
11.4
4
14
φ8
3.5
φ16
1.6
（29）
10
Width across flats
R1/8
R1/8
14
For options and made to order, see p.306.
14
40
Exhaust center
Pressure center
14（S2）
14（S2）
4（A）
2（B）
5（R1）
1（P）
3（R2）
4（A）
2（B）
5（R1）
1（P）
3（R2）
12（S1）
113-4E2-13
12
（S1）
113-4KE2-13
113-4E2-14
113-4KE2-14
14（S2）
14（S2）
14（S2）12
（S1）
14
（S2）12
（S1）
PR1
PR1
5（R1）
4（A）
2（B）
1
（P）
4（A）
5（R1）
3
（R2）4（A）
1
（P）
5（R1）
1（P）
5
（R1）
2（B）
3（R2）
4
（A）
1
（P）
2
（B）
2（B）
3
（R2）
PR2
12
（S1）
3
（R2）
PR2
12（S1）
Dimensions of Solenoid Valve 5-port , 2-, 3-position (mm)
Approximately
300
50
24
25
20
17.5
11
3
17.5
7.5
9 9
2-M2.6×0.45 Depth 3
Mounting thread
5
PR1
PR2
20
2-φ3.2
Mounting hole
〈Viewed from A〉
4.5
11.5 20
5（R1）
1（P）
21.5
3（R2）
3
3
110-4E2
110-4E2
2-Manual override
Non-locking type: Standard
Locking protruding type: -83
5-M5×0.8
113-4E2
28.2
12
（S1）
5
27.5
12.5
30
4.5
46
PR1
1（P）
3（R2）
5（R1）
PR2
50
24
25
20
17.5
11
PR1
25
55
20
2-φ3.2
Mounting hole
27.5
12.5
30
4.5
46
2-φ3.2
Mounting hole
2-φ2.8 Counterboreφ5.4 Depth 3
Mounting hole
130.4
74
5
34
21
5
5
9 9
10 10
61.2
5
3（R2）
2
（B）
41
5（R1）
1（P）
2-Manual override
Non-locking type: Standard
Locking protruding type: -83
33.7
17.5
4（A）
2（B）
3
5.5
3
7.5
2-PR
4（A）
4（A）
30
24
15
A113-4E2
Approximately
300
1（P）
5（R1）
3（R2）
2-Manual override
Non-locking type: Standard
Locking protruding type: -83
5-M5×0.8
33
3
Approximately
24
300
15
69.2
A113-4E2-25
PR2
113-4E2
3
5.5
5-Rc1/8
2-M5×0.8
5
3
5.5
2（B）
2-φ3.2
Mounting hole
12（S1）
12（S1）
14
（S2）
25
55
20
118.4
62
28.2
2-φ3.2
Mounting hole
31.7
5
10
5
9
2-φ2.8 Counterboreφ5.4 Depth 3
Mounting hole
3
5.5
25
20
17.5
11
2-Manual override
Non-locking type: Standard
Locking protruding type: -83
2（B）
59.2
5（R1）
1（P）
3（R2）
34
21
5
31
9
118.4
2-PR
4（A）
2（B）
2（B）
50
24
14（S2）
17.5
4（A）
4（A）
3
7.5
5
10
14（S2）
Approximately
300
30
24
15
3
Approximately
24
300
15
A110-4E2
A110-4E2-25
41.7
4.5
130.4
25
86.7
34
21
2-φ3.2
Mounting hole
5-Rc1/8
4.5
3 2-φ2.8 Counterboreφ5.4 Depth 3
5.5 Mounting hole
3
5.5
A
16.5 10
16.5 10
12.5 18
5（R1）
1（P）
3（R2）
4（A）
2（B）
2（B）
4（A）
5-M5×0.8
4（A）
2（B）
Manual override
Non-locking type: Standard
Locking protruding type: -83
PR
58.5
55
80.7
Manual override
Non-locking type: Standard
Locking protruding type: -83
2-M5×0.8
46
24
15
3
Approximately
24
300
27.5
12.5
30
30
15
A110-4E1
A110-4E1-25
1（P）
3（R2）
5（R1）
110-4E1
110-4E1
5-Rc1/8
2-M5×0.8
Additional Parts (To be ordered separately)
110-BASE
110-MUFF
●Muffler
For sub-base piping：KM-11
1.6
For direct piping：KM-05
110-SC
●Speed controller
For direct piping：SCE-M5
For sub-base piping：SCE-01
（29）
φ16
2-φ4.5
Mounting hole
M5×0.8
8
Width across flats
M5×0.8
14
Width across flats
24
（21）
16.5
11.4
4
14
φ8
3.5
9.2
85.7
（ To the top surface of
the valve）
5
●Mounting base : 110-21
10
Width across flats
R1/8
R1/8
14
14
40
Made to Order
-J41 (For φ4 tube, 2(A) or 4(A) port with fitting)
●Locking protruding type manual override : -83
110-ROCK
●Solenoid with DIN connector : -39
φ14.8
6.5
13
φ6
-J42 (For φ4 tube, 1(P), 2(A) ports with fittings)
-J61 (For φ6 tube, 2(A) or 4(A) port with fitting)
（2.4）
C
●Solenoid with straight connector : -PSL
110-PSL□
PRNote
M5×0.8
Quick fitting
10
●Solenoid with LED indicator : -L
34
1
（P）
28.2
A
36
-J42: 8.8
-J62: 9.5
Note : PR is on the side with the A port.
Approximately
300
10
24.5
-J41,-J42: 8.8
-J61,-J62: 9.5
1.8
34
3（R）
R
20.5
2（A）
2（A）
（44.1）
-J62 (For φ6 tube, 1(P), 2(A) ports with fittings)
The drawing shows the -J42 specification.
54
M12×1.25
（34.5）
●With quick fittings (2-, 3-port):
110-PSL□
（27） 7.5
Options
LED indicator
●With quick fittings (5-port):
LED indicator
-J42 (For φ4 tube, 4(A), 2(B) ports with fittings)
-J43 (For φ4 tube, 1(P), 4(A), 2(B) ports with fittings)
●Built-in interface unit : -FA
R
PRNote
44.5
20.5
B
Quick fitting
4（A）
16.5 10
2（B）
1.8
4（A）
1.8
2
（B）
-J42,-J43: 8.8
-J62,-J63: 9.5
29
D
2-M5×0.8
44
20
D'
The drawing shows the -J43 specification.
●Solenoid with L connector : -PLL
110-PLL□
30.5
-J63 (For φ6 tube, 1(P), 4(A), 2(B) ports with fittings)
Approximately
300
-J62 (For φ6 tube, 4(A), 2(B) ports with fittings)
5（R1）
LED indicator
LED indicator
1（P）
3（R2）
-J43: 8.8
-J63: 9.5
Note：PR is on the side with the A, B ports.
Remark: Valves with quick fittings do not have 2-φ3.2 side mounting holes. Moreover, the quick fittings are the following types:
TSK4-M8M (for φ4 tube), TSK6-M8M (for φ6 tube)
Model
Code
R (lead wire length)
A
B
C
D
D'
111E1, A111E1-25
82.5
75.5
90.6
77
77.2
110-4E1
88.5
81.5
96.6
83
83.2
-PSL, -PLL : 300
A110-4E1-25
94.5
87.5
102.6
89
89.2
110-4E2, A110-4E2-25
134
120
150.2
123
123.4
Made to order
-1L : 1000 -3L : 3000
113-4E2, A113-4E2-25
146
132
162.2
135
135.4
mm
Remarks
Overall length to the
end of the valve or subbase
Overall length to the end of
the opposite side solenoid
Dimensions of Tandem Solenoid Valve 5-port , 2-position (mm)
A110-4ME2-25-PSL
30
24
15
68
42
37.5
Manual override
2-φ2.8（Mounting hole）
Counterboreφ5.4 Depth 3
7.5
2-M5×0.8
DC24V
2-Rc1/8
3-Rc1/8
PR1
20
PR2
25
55
13
2
（B）
1（P）
3（R2）
5（R1）
B
56.5
4
（A）
98.7
92.7
84.5
A B
A
30
46
17.5
25
20
17.5
11
Approximately
300
2-LED indicator
2-φ3.2
（Mounting hole）
A110-4ME2-25-PLL
2-LED indicator
Manual override
2-φ2.8（Mounting hole）
Counterboreφ5.4 Depth 3
17.5
Approximately
300
30
24
15
78.8
52.8
25
20
17.5
11
2-M5×0.8
7.5
A C B
3-Rc1/8
DC24V
A B
PR1
20
2（B）
PR2
25
55
13
4（A）
2-φ3.2
（Mounting hole）
Options
●Locking manual lever type: -84
4
3
6
6
φ6
●Locking protruding type: -83
1（P）
3（R2）
5（R1）
B
90.5
84.5
56.5
A
30
46
2-Rc1/8
Dimensions of Tandem Solenoid Valve 5-port , 3-position (mm)
A113-4ME2-25-PSL
68
30
24
15
42
37.5
2-φ2.8（Mounting hole）
Counterboreφ5.4 Depth 3
7.5
2-M5×0.8
DC24V
2-Rc1/8
3-Rc1/8
PR1
20
3.5
PR2
25
55
13
2
（B）
1（P）
5（R1）
3（R2）
B
66
4
（A）
102.2
94
A B
A
30
46
17.5
25
20
17.5
11
Approximately
300
2-LED indicator
Manual override
2-φ3.2
（Mounting hole）
A113-4ME2-25-PLL
Approximately
300
2-LED indicator
Manual override
2-φ2.8（Mounting hole）
Counterboreφ5.4 Depth 3
17.5
7.5
30
24
15
78.8
52.8
25
20
17.5
11
2-M5×0.8
A C B
DC24V
3-Rc1/8
A B
4（A）
PR2
3.5
2（B）
20
13
66
25
55
PR1
94
B
2-φ3.2
（Mounting hole）
Options
●Locking manual lever type：-84
4
3
6
6
φ6
●Locking protruding type：-83
1（P）
3（R2）
5（R1）
A
30
46
2-Rc 1/8
Dimensions of Manifold for 2-, 3-port Valves (mm)
111M-F
111M□F
Unit dimensions
L
P
3.5
Manual override
Non-locking type: Standard
Locking protruding type: -83
3.5
16
16
8.5 15
16
Approximately
300
16
15 8.5
43
24
18
11
8
4
4-Rc1/8
（with 2 plugs）
14 6
7
23
21
15
30
2（A） 2（A）
20.5
8.5
1（P） 3（R）
74.7
2-φ4.2
Mounting hole
M5×0.8
3
111E1
Block-off plate
(-BP)
Model
L
P
111M2F
48
41
3F
64
57
4F
80
73
5F
96
89
6F
112
105
7F
128
121
8F
144
137
9F
160
153
10F
176
169
11F
192
185
12F
208
201
13F
224
217
14F
240
233
15F
256
249
16F
272
265
17F
288
281
18F
304
297
19F
320
313
20F
336
329
stn.1 stn.2
111M-A
111M□A
Unit dimensions
L
P
3.5
53
24
3.5
16
16
16
8.5 15
Manual override
Non-locking type: Standard
Locking protruding type: -83
Approximately
300
28
22.5
16
8
16
15 8.5
A111E1
Block-off plate
(-BP)
Rc1/8
8
2（A） 2（A）
19
16
stn.1 stn.2
2（A）
3（R）
P
41
3A
64
57
4A
80
73
5A
96
89
6A
112
105
7A
128
121
8A
144
137
4-Rc1/8
（with 2 plugs）
9A
160
153
13.5
29
36.5
1（P）
PR
42
39
16
5.2
A111E1
L
48
2-M5×0.8
（with 1 plug）
74.7
4-φ4.2
Mounting hole
Model
111M2A
10A
176
169
11A
192
185
12A
208
201
13A
224
217
14A
240
233
15A
256
249
16A
272
265
17A
288
281
18A
304
297
19A
320
313
20A
336
329
111M□AJ
16
16
8.5 15
3.5
16
Unit dimensions
53
24
28
22.5
16
8
16
15 8.5
Model
L
111M2AJ
48
41
3AJ
64
57
4-Rc1/8
（with 2 plugs）
-J4: 6.8
-J6: 7.5
5.2
1（P）
16
3（R）
42
PR
74.7
4-φ4.2
Mounting hole
39
2-M5×0.8
（with 1 plug）
13.5
29
36.5
3.5
Manual override
Non-locking type: Standard
Locking protruding type: -83
Approximately
300
L
P
A111E1
A111E1
Quick fitting
Block-off plate
(-BP)
2（A）
4AJ
80
73
5AJ
96
89
6AJ
112
105
7AJ
128
121
8AJ
144
137
9AJ
160
153
10AJ
176
169
11AJ
192
185
12AJ
208
201
13AJ
224
217
14AJ
240
233
15AJ
256
249
16AJ
272
265
17AJ
288
281
8
2（A） 2（A）
P
19
16
stn.1 stn.2
Options
304
297
320
313
20AJ
336
329
Made to Order
-J41 (For φ4 tube, 2(A) or 4(A) port with fitting)
●Solenoid with DIN connector: -39
φ14.8
6.5
φ6
-J61 (For φ6 tube, 2(A) or 4(A) port with fitting)
13
（2.4）
1
（P）3
（R）
2（A）
34
10
1.8
43
●Solenoid with LED indicator: -L
R
-J41: 8.8
-J61: 9.5
（34.5）
C
●Solenoid with straight connector: -PSL
110-PSL□
（44.1）
Quick fitting
54
M12×1.25
PRNote
2（A）
110-PSL□
（27） 7.5
●Locking protruding type manual override: -83
110-ROCK
●With quick fitting (2-, 3-port):
20.5
18AJ
19AJ
34
Note : PR is on the A port side.
LED indicator
-J42 (For φ4 tube, 4(A), 2(B) ports with fittings)
Approximately
300
28.2
●With quick fittings (5-port):
24.5
A
36
10
-J62 (For φ6 tube, 4(A), 2(B) ports with fittings)
LED indicator
●Solenoid with L connector: -PLL
110-PLL□
PRNote
Quick fitting
●Built-in interface unit: -FA
300
LED indicator
Note：PR is on the side with the 4(A), 2(B) ports.
D'
43
30.5
-J42: 8.8
-J62: 9.5
D
1.8
20
29
5
B
1.8
44
3（R2）
2（B）
2（B）
44.5
20.5
y
5（R1）
5
4（A）
1（P）
R
4（A）
LED indicator
Remark: Valves with quick fittings do not have 2-φ3.2 side mounting holes. Moreover, the quick fittings are
the following types:
TSK4-M8M (for φ4 tube), TSK6-M8M (for φ6 tube)
Model
Code
A
B
C
D
D'
111E1, A111E1
82.5
75.5
90.6
77
77.2
110-4E1, 110-4KE2, 113-4KE2, A110-4E1
88.5
81.5
96.6
83
83.2
110-4E2, A110-4E2
134
120
150.2
123
133.4
113-4E2, A113-4E2
146
132
162.2
135
135.4
mm
R(lead wire length)
-PSL, -PLL : 300
Made to order -1L : 1000, -3L : 3000
Dimensions of Manifold for Combination Mounting of 2-, 3-, 5-port Valves (mm)
110M-F
110M□F
L
P
3.5
Manual override
Non-locking type: Standard
Locking protruding type: -83 8.5
16
Approximately
300
3.5
16
16
15
16
15
Unit dimensions
43
24
4-φ4.2
Mounting hole
18
11
8
3
14
（S2）
14
（S2）
L
P
48
41
3F
64
57
4F
80
73
5F
96
89
4（A） 4（A）
3（R2）
41
7
2（B）
69.2
2（B）
15
5
2（B）
23
13
20
32
16
30
46
5（R1）
1（P）
5
4（A）
33
31
59.2
61.2
6-Rc1/8
（with 3 plugs）
4（A）
21.5
Model
110M2F
M5×0.8
12
（S1）
3
3
12
（S1）
3
110-4E1
110E1, 110E1-11
110-4E2
113-4E2
Block-off plate
(-BP)
Example of combination mounting
with twin solenoid valves
L
stn.1 stn.2 stn.3 stn.4 stn.5
Manual override
Non-locking type: Standard
Locking protruding type: -83
16
8.5
3.5
P
3.5
16
24
32
31
15
16
6F
112
105
7F
128
121
8F
144
137
9F
160
153
10F
176
169
11F
192
185
12F
208
201
13F
224
217
14F
240
233
15F
256
249
16F
272
265
17F
288
281
18F
304
297
19F
320
313
20F
336
329
15
M5×0.8
2（B）
3
2（B）
3
−
stn.1 stn.2 stn.3
stn.5
−
46
15
2（B）
30
4（A）
16
16.5 10
4（A） 4（A） 4（A）
1.5
52.5
82
36
14（S2）12（S1）14（S2）12（S1）
stn.7
4-φ4.2
Mounting hole
110M-FE
110M□FE
3.5
Manual override
Non-locking type: Standard
Locking protruding type: -83 8.5
Approximately
300
L
P
16
3.5
16
16
15
50
24
16
4-φ4.2
Mounting hole
15
14
（S2）
14
（S2）
25
19.5
12
4-M5×0.8
8.4 （with 2 plugs）
4
6-Rc1/8
2（B）
2（B）
2（B）
16
50
69.2
41
5
21.5
4（A）
M5×0.8
12
（S1）
3
3
110-4E1
110E1, 110E1-11
3
12
（S1）
110-4E2
113-4E2
Block-off plate
(-BP)
stn.1 stn.2 stn.3 stn.4 stn.5
For options and made to order, see p.310.
20
32
45
60
4（A）
30
4（A）
PR2 1（P）PR1
3（R2）
5（R1）
4（A）
33
5
31
61.2
59.2
（with 3 plugs）
Unit dimensions
Model
L
110M2FE
48
P
41
3FE
64
57
4FE
80
73
5FE
96
89
6FE
112
105
7FE
128
121
8FE
144
137
9FE
160
153
10FE
176
169
11FE
192
185
12FE
208
201
13FE
224
217
14FE
240
233
15FE
256
249
16FE
272
265
17FE
288
281
18FE
304
297
19FE
320
313
20FE
336
329
110M-A
110M□A
L
P
3.5
16
Manual override
Non-locking type: Standard
Locking protruding type: -83
16
8.5
Approximately
300
2-φ4.2
Mounting
hole
3.5
16
15
16
15
60
24
Unit dimensions
35
29.5
15
13
4-M5×0.8
（with 2 plugs）
14
（S2）
14
（S2）
3・5（R）
1（P）
24.5
42
38
2-Rc1/8
（with 1 plug）
7.5
69.2
41
21.5
32.5
PR2
50
53
PR1
33
31
59.2
61.2
2-Rc1/4
（with 1 plug）
12
（S1）
12
（S1）
A110-4E1
A110-4E2
A110E1, A110E1-11
A113-4E2
Block-off plate
(-BP)
2-Rc1/8
Plug B when mounting A110E1
Plug A when mounting A110E1-11
19.5
2（B）2（B）
7.5
4（A）
5
Model
L
P
110M2A
48
41
3A
64
57
4A
80
73
5A
96
89
6A
112
105
7A
128
121
8A
144
137
9A
160
153
10A
176
169
11A
192
185
12A
208
201
13A
224
217
14A
240
233
15A
256
249
16A
272
265
17A
288
281
18A
304
297
19A
320
313
20A
336
329
2（B）
4（A）
4（A）
3
stn.1 stn.2 stn.3 stn.4 stn.5
110M-A
110M□AJ
L
P
16
16
15
16
35
29.5
15
13
2-φ4.2
Mounting hole
15
14
（S2）
14
（S2）
2-Rc1/4
（with 1 plug）
2-Rc1/8
（with 1 plug）
PR2
41
69.2
Plug
For 2-, 3-port valve mounting
A110-4E2
A110E1, A110E1-11
A113-4E2
Block-off plate
(-BP)
2-Quick fittings (per each station)
Plug B when mounting A110E1
Plug A when mounting A110E1-11
20.5
2（B）2（B）
6.5
4（A）
5
2（B）
4（A）
4（A）
3
stn.1 stn.2 stn.3 stn.4 stn.5
For options and made to order, see p.310.
1（P）
PR1
33
50
53
32.5
-J4: 6.8
-J6: 7.5
12
（S1）
3・5（R）
61.2
59.2
31
21.5
-J4: 16.7
-J6: 21.1
12
（S1）
A110-4E1
Unit dimensions
4-M5×0.8
（with 2 plugs）
42
38
8.5
60
24
7.5
16
Manual override
Non-locking type: Standard
Locking protruding type: -83
Approximately
300
3.5
24.5
3.5
Model
L
110M2AJ
48
P
41
3AJ
64
57
4AJ
80
73
5AJ
96
89
6AJ
112
105
7AJ
128
121
8AJ
144
137
9AJ
160
153
10AJ
176
169
11AJ
192
185
12AJ
208
201
13AJ
224
217
14AJ
240
233
15AJ
256
249
16AJ
272
265
17AJ
288
281
18AJ
304
297
19AJ
320
313
20AJ
336
329
Dimensions of Manifold for Combination Mounting of Tandem Solenoid and 2-, 3-, 5-port Valves (mm)
110M□A
L
P
Manual override 8.5
Approximately
300
3.5
16
16
16
A C B
DC24V
A B
A B
B
A
B
PR2
PR1
Unit dimensions
4-M5×0.8
（with 2 plugs）
2-Rc1/4
（with 1 plug）
2-Rc1/8
（with 1 plug）
7.5
32
1（P）
50
53
15.5
21.5
32.5
31
34.5
A
62
59.2
A C B
DC24V
35
29.5
15
13
2-φ4.2
Mounting hole
15
15
98.8
52.8
3・5（R）
16
24.5
42
38
3.5
A110-4E1
A110-4ME2-81-PLL
A110E1, A110E1-11
A113-4ME2-81-PLL
Block-off plate
(BP)
2-Rc1/8 (per each station)
Plug B when mounting A110E1
Plug A when mounting A110E1-11
19.5
2（B）2（B）
7.5
4（A）
2（B）
L
P
48
41
3A
64
57
4A
80
73
5A
96
89
6A
112
105
7A
128
121
8A
144
137
9A
160
153
10A
176
169
11A
192
185
12A
208
201
13A
224
217
14A
240
233
15A
256
249
16A
272
265
17A
288
281
18A
304
297
19A
320
313
20A
336
329
4（A）
4（A）
5
Model
110M2A
3
stn.1 stn.2 stn.3 stn.4 stn.5
110M□AJ
L
P
16
Model
L
P
110M2AJ
48
41
3AJ
64
57
4AJ
80
73
5AJ
96
89
6AJ
112
105
7AJ
128
121
8AJ
144
137
9AJ
160
153
10AJ
176
169
11AJ
192
185
12AJ
208
201
13AJ
224
217
14AJ
240
233
15AJ
256
249
16AJ
272
265
A113-4ME2-81-PLL
17AJ
288
281
Block-off plate
(BP)
18AJ
304
297
19AJ
320
313
20AJ
336
329
16
16
2-φ4.2
Mounting
hole
15
59.2
15
A C B
DC24V
A B
A B
B
A
B
PR2
4-M5×0.8
（with 2 plugs）
2-Rc1/4
（with 1 plug）
2-Rc1/8
（with 1 plug）
-J4: 7
-J6: 7.5
-J4: 17
-J6: 21.4
7.5
PR1
1（P）
50
53
15.5
32
32.5
21.5
31
34.5
A
A C B
DC24V
35
29.5
15
13
3・5（R）
8.5
Unit dimensions
98.8
52.8
62
16
Manual override
Approximately
300
3.5
24.5
42
38
3.5
Plug
For 2-, 3-port valve mounting
A110-4E1
A110-4ME2-81-PLL
A110E1, A110E1-11
2-Quick fittings（per each station）
Plug B when mounting A110E1
Plug A when mounting A110E1-11
20.5
2（B）2（B）
6.5
4（A）
5
2（B）
4（A）
4（A）
3
stn.1 stn.2 stn.3 stn.4 stn.5
Cylinder Operating Speed and Flow Rate
●Measurement conditions
●Measurement conditions
●Air pressure：0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length: φ2.5 [0.10in.]×1000mm [39in.]
●Fitting：Quick fitting TS4-M5
Load
(%)
●Load ratio =
Load
Cylinder theoretical thrust
●Cylinder stroke:150mm [5.91in.]
●Air pressure：0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length：φ4 [0.16in.]×1000mm [39in.]
●Fitting：Quick fitting TS6-01
Load
●Load ratio =
(%)
Cylinder theoretical thrust
●Cylinder stroke:150mm [5.91in.]
Load
Air-piloted valve A110-4A-25
Cylinder
Air-piloted valve 110-4A
Cylinder
0.5MPa
0.5MPa
Flow rate
110 series
MPa
0.7
0.6
Fitting TS6-01
Maximum operating speed
Maximum operating speed
Maximum operating speed
800
600
400
φ20 [0.787in.]
φ25 [0.984in.]
φ32 [1.260in.]
φ40 [1.575in.]
200
0.2
10
20
30
40
50
Load ratio
60
600
100
200
300
400
Flow rate R/min(ANR)
φ20 [0.787in.]
φ25 [0.984in.]
φ32 [1.260in.]
φ40 [1.575in.]
φ50 [1.969in.]
400
200
Operating Principles and Major Parts
0.2
0.1
When the supply pressure is 0.5MPa [73psi.]
and the flow rate is 210R/min [7.41ft.3/min.]
(ANR), the valve outlet pressure becomes
0.4 MPa [58psi.].
800
70
%
0.3
How to read the graph
1000
0
0
0.4
0.3
1MPa = 145psi., 1R/min = 0.0353 ft.3/min.
mm/s
1200
1000
0.5
0.4
0
Maximum operating speed
mm/s
1200
Supply pressure
（MPa）
0.6
0.5
0.1
Fitting TS4-M5
0.7
10
20
30
40
50
Load ratio
60
70
%
1mm/s = 0.0394in./sec.
5-port, 2-position
Pilot connection port
110-4A
110-4A2
Piston
Stem
Normal state
Operating state
(Condition with pilot air applied to 12(PB), and then released)
14
（PA）
Body
5
（R1）
4
（A）
5（R1）
5（R1）
4（A）
4（A）
1（P）
1（P）
2（B）
2（B）
3（R2）
Spring
Parts
Materials
Body
Aluminum alloy
（anodized）
Stem
Lip seal
Synthetic rubber
Mounting base Mild steel (zinc plated)
Sub-base
Aluminum alloy (anodized)
2（B）
3（R2）
3（R2）
Lip seal
End cover
Major Parts and Materials
1（P）
12
（PB）
SOLENOID VALVES 110 SERIES
A110-4A-25
Valve outlet pressure
110-4A
Dimensions of Air-piloted 5-port, 2-position Valve (mm)
110-4A
110-4A2
M5×0.8
Pilot connection port
24
15
12
7.5
10
1（P）
2（B）
12（PB）
2-φ3.2
Mounting hole
3
3
5.5
5.5
5
2-M2.6 Depth 2.5
Mounting thread
10
2-φ2.8 Counterboreφ5.4
Depth 3
Mounting hole
3（R2）
9
25
2（B）
10
9
5
5
21.5
5.5
9
5.5
5
50
1（P）
3
4（A）
2（B）
3（R2）
3
5（R1）
5
9
10
5
9
46.5
4（A）
4（A）
2（B）
12
14（PA）
5（R1）
5
4（A）
24
5-M5×0.8
Connection port
5
5-M5×0.8
Connection port
7.5
5
15
2-M5×0.8
Pilot connection port
2-φ2.8 Counterboreφ5.4
Depth 3
Mounting hole
5
2-φ3.2
Mounting hole
9
12（PB）
4.5
4.5
Options
●Mounting base : -21
●With quick fittings: -J42（For φ4 tube, 4(A), 2(B) ports with fittings）
-J43（For φ4 tube, 1(P), 4(A), 2(B) ports with fittings）
-J62（For φ6 tube, 4(A), 2(B) ports with fittings）
-J63（For φ6 tube, 1(P), 4(A), 2(B) ports with fittings）
The drawing shows the -J43 specification.
1.6
5
4（A）
2-M5×0.8
5（R1）
5
51.5
Quick fitting
4（A）
1（P）
5
2（B）
3（R2）
2（B）
2-φ4.5
Mounting hole
1.8
-J42,-J43: 8.8
-J62,-J63: 9.5
-J43: 8.8
-J63: 9.5
9
24
9
1.8
4.5
4.5
14
14
40
●Speed controller : -70
●Muffler : -75
（20.5）
4
14
φ8
9.2
3.5
M5×0.8
8
Width across flats
M5×0.8
Dimensions of Air-piloted 5-port, 2-position Valve (mm)
A110-4A
M5×0.8
A110-4A2
2-M5×0.8
24
15
Pilot connection port
7.5
Pilot connection port
15
24
12
7.5
12
9
25
9
21.5
50
46.5
9
9
14（PA）
12（PB）
5.5
2-φ2.8 Counterboreφ5.4 Depth 3
2-φ2.8 Counterboreφ5.4 Depth 3
Mounting hole
5.5
5.5
5.5
12（PB）
Options
2-M5×0.8
PR
●Sub-base : -25
7.5
17.5
5.5
12
12
11
17.5
20
25
50
11.4
(21)
10
Width across flats
R1/8
23
15
2-φ3.2
Mounting
hole
30
●Speed controller : -70
3（R2）
PR2
7.5
5.5
15
1（P）
17.5
9
55
27.5
6.5
2（B）
23
PR1
9
6.5
4（A）
5（R1）
5-Rc1/8
Connection port
PC Board Manifold 110 Series Specifications
Manifold Basic Models and Specifications
port manifold with
1(P), 3(R2), 5(R1) manifolds All port manifold All
quick fittings
Number 8 stations
of units 16 stations
110M8FP
110M8AP
110M8AJP
110M16FP
110M16AP
110M16AJP
2-, 3-port
110E1
A110E1
5-port, single solenoid
110-4E1
A110-4E1
110-4E2
A110-4E2
110-4KE2
A110-4KE2
113-4E2
A113-4E2
113-4KE2
A113-4KE2
Item
Type of
5-port,
mounting valve double solenoid
5-port, 3-position
Flow Rate
MPa
0.7
Valve outlet pressure
Manifold function
Basic model
0.6
Connector for flat cable (AWG 28)Note1: With short clip (standard)
With long clip (optional)Note2
Wiring type
Positive common (standard)
Negative common (optional: -CM)Note 2
Common wiring
Operating temperature range (atmosphere and media) °C [°F]
5〜50 [41〜122]
m/s2 {G}
Shock resistance
294.2 {30.0}
Mounting direction
Any
0.4
0.1
110-4E1 110-4E2 110-4KE2 113-4E2 113-4KE2
AP, AJP type manifolds A110E1 A110-4E1 A110-4E2 A110-4KE2 A113-4E2 A113-4KE2
Item
0
MPa
Internal pilot type
4.2〔0.23〕
Lubrication
3.8〔0.21〕
Not required
Operating pressure range MPa{kgf/cm2}[psi.]
0.15〜0.7 {1.5〜7.1} [22〜102]
2
1.05 {10.7} [152]
Proof pressure MPa{kgf/cm }[psi.]
Response timeNote ON/OFF
ms
Maximum operating frequency
Hz
Minimum time to energize for self holding
ms
15/20 or below
20 or below
─
15/30 or below
0.4
0.3
0.2
0.1
50
DC12V
Allowable leakage current
mA
Insulation resistance
MΩ
DC24V
10.8〜13.2
（12±10％）
21.6〜26.4
（24±10％）
140
（1.7W）
75
（1.8W）
8
4
Color of lead wire
300
400
Port
Location of piping ports
1
（P）
Manifold
Rc1/8
（
4 A）
,（
2 B）
Valve
M5×0.8Note
3 R2）
（
,（
5 R1）
Manifold
Rc1/8
（
4 A）
,（
2 B）
110M□AP
3, 5
（R）
Port size
Rc1/8
Manifold
PR
Rc1/4
M5×0.8
1
（P）
Rc1/8
（
4 A）
,（
2 B）
Quick fitting for
φ4 orφ6
Manifold
3, 5
（R）
Rc1/4
PR
M5×0.8
Note : When the mounting valve is a female thread
specification, the ports are this size. For the built-in
quick fitting type, quick fittings for φ4 are installed.
Red (＋), Black (−)
Color of LED indicator
200
1
（P）
110M□AJP
Over 100
113-4E2
113-4KE2
A113-4E2
A113-4KE2
Manifold Connection Port Size
Plug connector type
Straight connector -PSL: With dedicated lead wire for PC board connection, with connector
Wiring type
100
0.4
1MPa = 145psi., 1R/min = 0.0353ft.3/min.
Flywheel diode incorporated for surge suppression
Current (when rated voltage is applied) mA
400
Flow rate R/min(ANR)
110M□FP
DC V
0.3
0.2
0.1
─
Manifold model
Operating voltage range
300
Supply pressure
（MPa）
0.7
0.6
0.5
0.5
Solenoid Specifications
Type
200
0.6
0
Note: Values when air pressure is 0.5MPa {5.1kgf/cm2} [73psi.]. The values for □110-4E2
are when switching from the opposite position, while the valves for □113-4E2 are
those of the closed center valve, when switching from the neutral position.
Rated voltage
100
0.7
5
Item
0.2
0.1
When the supply pressure is 0.5MPa [73psi.] and the flow rate
is 210R/min [7.41ft.3/min.] (ANR), the valve outlet pressure
becomes 0.4 MPa [58psi.].
Valve outlet pressure
Operation type
mm2
0.3
Flow rate R/min(ANR)
1MPa = 145psi., 1R/min = 0.0353ft.3/min.
Air
Media
Effective area〔Cv〕
110E1
110-4E1
110-4E2
110-4KE2
A110E1
A110-4E1
A110-4E2
A110-4KE2
0.4
0.3
0.2
Supply
pressure
（MPa）
How to read the graph
Solenoid Valve Specifications
110E1
0.6
0.5
0.5
Notes: 1. For details about specifications, see the specifications of the connector for the flat
cable.
2. For order codes, see p.324.
Basic model FP type manifold
0.7
Red
Mass
Manifold
model
Specifications of Connector for Flat Cable
Item
Order code
Blank
-LC
Header
Box type, with short clip
(Part number:
3662-5002SCSC)
Box type, with long clip
(Part number:
3662-5002LCSC)
Socket Note
Open end type,
with nose
(Part number:
7910-6500SC)
Strain relief Note
─
Included
(Part number:
3448-7910J)
110M8FP
Standard
MIL-C-83503
conformity
(made by
Sumitomo 3M
Ltd.)
Remark: Regarding the units with center slots (grooves), note that there is no key groove for
the prevention of erroneous insertion.
Note: Included at shipping.
110M16FP
110M8AP
110M16AP
g [oz.]
Manifold
mass
Mounting valve mass
Blockoff
□110E1 □110-4E1 □110-4E2 □113-4E2 plate
240 [8.47]
80
80
125
145
6
450 [15.87] [2.82] [2.82] [4.41] [5.11] [0.21]
590 [20.81]
85
85
130
150
11
1120 [39.51] [3.00] [3.00] [4.59] [5.29] [0.39]
590＋(7×n1)＋(4×n2)
[20.81 ＋(0.25×n1)＋
(0.14×n2)]
85
85
130
150
11
1120＋(7×n1)＋(4×n2) [3.00] [3.00] [4.59] [5.29] [0.39]
110M16AJP [39.51＋(0.25×n1)＋
(0.14×n2)]
110M8AJP
Remark: n1 is the total number of stations with -J4, while n2 is
the total number with -J6.
PC Board Manifold 110 Series Order Codes
■ Common wiring ■ Connector
Positive common
With short clip
■ 2-, 3-port valve
Number of ports
3-port
A
■ 3-position valve ■ Port fitting
■ Manual
Valve function
specifications
override
P
4（A）
With long clip
Blank
2-port
-J41
Blank
Exhaust center
4（A）
A
P
Straight connector
with LED indicator
1（P）
●A port of 110E1
Negative common
Quick fittings
for φ4 tube
3（R2）
R
Blank
Non-locking type
5（R1）
2（B）
Blank
Quick fittings
for φ4 tube
Closed center
■ Manifold
■ Wiring type
Connection port
-J4
Blank
Locking protruding
type
-PSL
Quick fittings
for φ6 tube
5（R1）
1（P）
2（B）
3（R2）
-CM
-LC
-2
-13
Valve function
Normally closed (NC)
Pressure center
A
4（A）
P
-J42
-83
-J6
●A, B ports of
5-port
5（R1）
1（P）
2（B）
3（R2）
R
Blank
-14
Normally open
（NO）
P
A
R
-11
Manifold model
Number of units
Station
Basic model
PC board manifold
for combination mounting of 2-, 3-, 5-port valves
-110E1
Voltage
-2,-11
-J41
-110-4E1
FP
-CM
-LC
stn.□ -110-4E2
⁝
stn.□ -110-4KE2
-J42
-113-4E2
110M
-A110E1
DC12V
DC24V
-PSL
DC12V
DC24V
-2,-11
-A110-4E1
AP
AJP
-CM
-LC
stn.□ -A110-4E2
⁝
stn.□ -A110-4KE2
-A113-4E2
-A113-4KE2
●Mounting position from
Remark : □110E1 is 3-port,
the left-hand side when
and normally closed
facing the 4(A), 2(B) ports.
（NC）as the
●Since the twin solenoid valve requires
standard.
2 stations per valve to mount, the
For □113-4E2, a
second station (solenoid S1 side)
closed center is
should be blank.
standard.
●When selecting □110-4E2 or □113-4E2,
always enter -BP for the next station.
-83
●Specify the valve model for each station.
●Enter -BP when closing a station with a block-off
plate without mounting a valve.
●□110-4E2 and □113-4E2 cannot be used for
the last station.
●When mounting □ 110-4E2 or □ 113-4E2,
always enter -BP for the next station.
Made to Order
Block-off plate
AJP type manifold
AJP
F
A
For FP type manifold
For AP, AJP type manifolds
-J4
-J6
-13
-14
Additional Parts (To be ordered separately)
●110 M F -BP
-PSL
-13
-14
-113-4KE2
8
16
-83
●For the AJP type
manifold only.
Dimensions (mm)
110M8FP
110M16FP
Unit dimensions
8 10
D
10 8
105
129
（Only for 16 units）
Model
L
P
D
110M8FP
144
137
108
110M16FP
272
265
236
Option dimensions
Connector for flat cable
With short clip : Standard
With long clip : -LC
L
P
3.5
16
8.5
Model
A
Short clip
12.5
Long clip
15.5
3.5
16
16
15
56
16
15
34
8.5
21
Manual override
A
Non-locking type: Standard
Locking protruding type: -83
4（A）
4（A）
3
2（B）
2（B） 2（B）
2（B）
2（B）
7
2（B）
68
78.5
3
2（B）
15
21.5
16.5 10
1.5
2（B）
3
4-φ4.2
Mounting
hole
12（S1）
M5×0.8
12（S1）
110-4E1
110-4E2
110E1,110E1-11
113-4E2
3
Block-off plate
（-BP）
Options
●Locking protruding type manual override: -83
●With quick fittings: -J41 (A port with fitting)
-J42 (A, B ports with fittings)
The drawing shows the -J42 specification.
PR
6.5
5
2（B）
1.8
1.8
-J42, -J43: 8.8
-J62, -J63: 9.5
5（R1）
1（P）
4（A）
2（B）
3（R2）
4（A）
5
φ6
Quick fitting
46
Note: PR is on the side with the 4(A), 2(B) ports.
71.5
4（A）
32
4（A）
23
4（A）
5（R1）
4（A）
3（R2）
4（A）
148
4（A）
1（P）
68
4（A）
16
30
46
4（A）
69.5
14（S2）
14（S2）
11
14
6-Rc1/8
（with 3 plugs）
Dimensions (mm)
110M8AP
110M16AP
Unit dimensions
8 10
D
105
10 8
129
（Only for 16 units）
Model
L
P
D
110M8AP
144
137
108
110M16AP
272
265
236
Option dimensions
Model
A
Short clip
12.5
Long clip
15.5
Connector for flat cable
With short clip: Standard
With long clip: -LC
L
P
3.5
16
3.5
16
16
15
8.5
73
16
15
34
8.5
4-M5×0.8
（with 2 plugs）
38
2-Rc1/4
（with 1 plug）
Manual override
A
Non-locking type: Standard
Locking protruding type: -83
12（S1）
2-φ4.2
Mounting
hole
12（S1）
A110-4E1
A110E1, A110E1-11
A110-4E2
A113-4E2
Block-off plate
（-BP）
4（A） 4（A）
4（A）
5
3
Option
●Locking protruding type manual override: -83
φ6
6.5
2-Rc1/8（per each station）
Plug B when mounting A110E1
Plug A when mounting A110E1-11
22.5
2（B）
3
10.5
2（B） 2（B）
32.5
38
42
24.5
78.5
PR2
PR1
1（P）3・5（R）
16
18
7.5
5
68
78.5
21.5
32.5
50
53
148
68
14（S2）
69.5
14（S2）
2-Rc1/8
（with 1 plug）
Dimensions (mm)
110M8AJP
110M16AJP
Unit dimensions
D
8 10
105
Model
L
P
D
110M8AJP
144
137
108
110M16AJP
272
265
236
10 8
129
（Only for 16 units）
Option dimensions
Connector for flat cable
With short clip: Standard
With long clip: -LC
L
P
3.5
16
A
12.5
B
Long clip
15.5
Quick fitting forφ4 tube
─
6.8
16.7
Quick fitting for φ6 tube
─
7.5
21.1
73
16
15
8.5
34
─
4-M5×0.8
（with 2 plugs）
38
2-Rc1/4
（with 1 plug）
Manual override
A
Non-locking type: Standard
Locking protruding type: -83
12（S1）
2-φ4.2
Mounting
hole
12（S1）
Plug
For 2, 3-port valve mounting
A110-4E1
A110E1, A110E1-11
A110-4E2
A113-4E2
4（A）
4（A）
4（A）
5
3
φ6
2-Quick fittings (per each station)
Plug B when mounting A110E1
Plug A when mounting A110E1-11
23.5
2（B）
3
9.5
2（B） 2（B）
●Locking protruding type manual override: -83
38
42
24.5
78.5
PR2
PR1
1
（P）3・5（R）
16
18
32.5
Block-off plate
（-BP）
Option
7.5
68
78.5
C B 5
21.5
32.5
50
53
148
68
14（S2）
69.5
14（S2）
6.5
C
─
3.5
16
16
15
8.5
Model
Short clip
2-Rc1/8
（with 1 plug）
">