Koganei BTAL Single acting non-rotating pull type Instruction manual

BK-UC003 Ver.1.0
Air Cylinder
MULTI MOUNT CYLINDER
INSTRUCTION MANUAL Ver.1.0
Handling Instructions and Precautions
Replacement of mounting brackets
Sensor switches
●Rod side mounting bracket
Remove the rod end nut, loosen the rod cover (mounting bracket) mounting screws, and
remove the rod cover (mounting bracket). Assemble the replacement mounting bracket by
reversing the order of procedures for removal.
For non-rotating cylinders, loosen the setscrew for plate and remove the plate assembly, and
remove the rod cover (mounting bracket). For assembly, align and assemble the guide pin
holes of the mounting bracket and the cylinder body, insert the plate assembly, and tighten
and secure the setscrew for plate against the piston rod. In this case, retract the piston rod in
the fully retracted position at the head side stroke end, maintain a clearance of about 0.5mm
[0.020in.] between the plate and rod bushing, and secure the plate assembly in place.
Head cover mounting screw
Spring
Procedure for finding the best
sensing position
●Setting the head side stroke end
1. Push piston rod to the fully retracted
position.
2. Install a sensor switch in a holder without
tightening a mounting screw all the way,
move the switch from head side to rod side
until it turns ON (for ZC130□, ZC153□ and
CS11T□, when the LED lights up), then
move the switch 1 notch (= 1mm [0.039in.])
for ZC130□ and ZC153□, or 2 notches (=
2mm [0.079in.]) for CS5T□ and CS11T□
toward the rod side, and tighten the
mounting screw.
Sensor holder
Mounting
screw
Head cover
Rod bushing
Setscrew for plate
Moving
Head cover
1 notch ＝1mm [0.039in.]
Main body
Spring holder
Rod cover
Rod cover mounting screw
Plate assembly
Rod end nuts
The diagram shows a non-rotating single acting
push type cylinder.
●Head side mounting bracket
Loosen the head cover (mounting bracket) mounting screws and remove the head cover
(mounting bracket). Assemble the replacement mounting bracket by reversing the order of
procedures for removal.
Cautions: 1. To increase the mounting accuracy of the side mounting, assemble so that the rod cover
and head cover do not protrude from the cylinder body, and mount so that the cylinder body
contacts tightly to the device.
2. Use the supplied mounting screws, or when using commercial screws, use the sizes shown
in the table below to secure mounting brackets in place.
●Setting the rod side stroke end
Conduct the same procedure as the head
side, but on the reversed way.
1. Pull piston rod to the fully extended position.
2. Install a sensor switch in a holder without
tightening a mounting screw all the way,
move the switch from rod side to head side
until it turns ON, then move the switch 1
notch (=1mm [0.039in.]) for ZC130□ and
ZC153□, or 2 notches (= 2mm [0.079in.])
for CS5T□ and CS11T□ toward head side,
and tighten the mounting screw.
●Caution when installing cylinder with sensor
switch
Model marking surface
Bore size mm [in.]
Screw size
Length of below head mm [in.]
6 [0.236]
M2.6×0.45
6 [0.236]
10 [0.394]
M3×0.5
8 [0.315]
16 [0.630]
M4×0.7
8 [0.315]
Sensing surface
3. Refer to the figures in the table below for the tightening torque of the non-rotating cylinder’s
setscrew for plate, and for the size of the Allen wrench used.
Bore size mm [in.]
Tightening torque N·cm [in·lbf]
Hexagonal bar spanner nominal size mm [in.]
6 [0.236]
49 [4.37]
1.27 [0.050]
10 [0.394]
98.1 [8.68]
1.5 [0.059]
16 [0.630]
137.3 [12.2]
2 [0.079]
In the ZC type
sensor switches,
the opposite
side from the
model marking
surface is the
sensing surface
side. Mount it
so that the
cylinder magnet
comes to the
sensing surface
side.
General precautions
Piping
Lubrication
1. In applications with high load ratio or high
speed, use an externally mounted stopper
to prevent direct shock to the cylinder.
2. Use the cylinder body’s 4-M3 × 0.5 female
thread only for mounting a sensor switch or
shield plate.
The product can be used without lubrication, if
lubrication is required, use Turbine Oil Class 1
(ISO VG32) or equivalent.
Avoid using spindle oil or machine oil.
Media
Piping
Always thoroughly blow off (use compressed
air) the tubing before connecting it to the
cylinder. Entering chips, sealing tape, rust,
etc., generated during piping work could result
in air leaks or other defective operation.
Atmosphere
1. If using in locations subject to dripping
water, dripping oil, etc., or to large amounts
of dust, use a cover to protect the unit.
2. The product cannot be used when the
media or ambient atmosphere contains any
of the substances listed below.
Organic solvents, phosphate ester type
hydraulic oil, sulphur dioxide, chlorine gas,
or acids, etc.
1. Use air for the media. For the use of any
other media, consult us.
2. Air used for the cylinder should be clean air
that contains no deteriorated compressor
oil, etc. Install an air filter (filtration of a
minimum 40 µm) near the cylinder or valve
to remove collected liquid or dust. In
addition, drain the air filter periodically.
MULTI MOUNT CYLINDERS
Standard Cylinders
Symbols
●Double acting type (BDA)
●Single acting push type (BSA)
Specifications
Bore size mm [in.]
6 [0.236]
Item
●Single acting pull type (BTA) ● Double acting double rod type
(BDAD)
Media
pressure range
MPa
N [lbf.]
Pressure
Air pressure MPa [psi.]
Bore size Piston rod Operation
area
diameter
2
0.2
0.1
0.3 0.4 0.5 0.6 0.7
mm
mm [in.] mm [in.]
type
[in.2] [15] [29] [44] [58] [73] [87] [102]
28.2
5.6 8.5 11.3 14.1 16.9 19.7
Push side [0.0437] − [1.26] [1.91] [2.54] [3.17] [3.80] [4.43]
Double
acting type
21.2
4.2 6.4 8.5 10.6 12.7 14.8
Pull side
[0.0329] − [0.94] [1.44] [1.91] [2.38] [2.85] [3.33]
6
3
[0.236] [0.118]
28.2
1.7 4.6 7.4 10.2 13 15.8
Single acting push type
[0.0437] − [0.38] [1.03] [1.66] [2.29] [2.92] [3.55]
21.2
Single acting pull type
[0.0329]
Double
acting type
10
5
[0.394] [0.197]
16
6
[0.630] [0.236]
−
−
2.5 4.6 6.7 8.8 10.9
[0.56] [1.03] [1.51] [1.98] [2.45]
[psi.]
0.1〜0.7
[15〜102]
0.08〜0.7
[12〜102]
Single acting
push type
0.2〜0.7
[29〜102]
0.15〜0.7
[22〜102]
0.15〜0.7
[22〜102]
Single acting
pull type
0.3〜0.7
[44〜102]
0.2〜0.7
[29〜102]
0.2〜0.7
[29〜102]
Double acting
double rod type
0.2〜0.7
[29〜102]
0.15〜0.7
[22〜102]
0.1〜0.7
[15〜102]
Proof pressure
1.03 [149]
MPa [psi.]
Operating temperature range
0〜60 [32〜140]
°C [°F]
50〜500 [2.0〜19.7]
Operating speed range mm/s [in./sec.]
Rubber bumper
Not required
Cushion
(If lubrication is required,
use Turbine Oil Class 1 [ISO VG32] or equivalent.)
Lubrication
Port size
M5×0.8
+1 +0.039
]
0[ 0
78.5
7.9 15.7 23.6 31.4 39.3 47.1 55
[0.1217] [1.78] [3.53] [5.31] [7.06] [8.83] [10.59] [12.36]
Pull side
58.9
5.9 11.8 17.7 23.6 29.5 35.3 41.2
[0.0913] [1.33] [2.65] [3.98] [5.31] [6.63] [7.94] [9.26]
Operation Type, Bore Size, and Stroke
7.9 15.8 23.6 31.5 39.3 47.2
− [1.78] [3.55] [5.31] [7.08] [8.83] [10.61]
58.9
Single acting pull type [0.0913]
9.9 15.8 21.7 27.5 33.4
4
− [0.90] [2.23] [3.55] [4.88] [6.18] [7.51]
201 20.1 40.2 60.3 80.4 100.5 120.6 140.7
Push side [0.312]
[4.52] [9.04] [13.56] [18.07] [22.59] [27.11] [31.63]
Double
acting type
172 17.2 34.4 51.6 68.8 86 103.2 120.4
Pull side
[0.267] [3.87] [7.73] [11.60] [15.47] [19.33] [23.20] [27.07]
201
Single acting push type [0.312]
18.6 38.7 58.8 78.9 99 119.1
− [4.18] [8.70] [13.22] [17.74] [22.26] [26.77]
172
[0.267]
12.8 30 47.2 64.4 81.6 98.8
− [2.88] [6.74] [10.61] [14.48] [18.34] [22.21]
Single acting pull type
Stroke
mm
Standard strokes
10
5, 10, 15, 20, 25, 30
16
6
Single acting push type
Single acting pull type
10
5, 10, 15
16
6
Double acting
double rod type
10
16
N [lbf.]
Zero stroke
Bore size
6
Double acting type
Spring Return Force (Only for Single Acting Type)
Item
mm [in.]
mm
Operation type
Note: For the double acting double rod type, see the double acting type pull
side.
End of stroke
5
10
15
5, 10, 15
2.9 [0.65]
2.5 [0.56]
2.0 [0.45]
3.9 [0.88]
10 [0.394]
6.9 [1.55]
4.9 [1.10]
2.9 [0.65]
7.8 [1.75]
16 [0.630]
17.7 [3.98] 13.7 [3.08] 9.8 [2.20]
21.6 [4.86]
6 [0.236]
0.15〜0.7
[22〜102]
Push side
78.5
[0.1217]
Bore size mm [in.]
Double acting
type
Stroke tolerance
Single acting push type
16 [0.630]
Air
Operating
Cylinder Thrust
10 [0.394]
5, 10, 15, 20, 25, 30
Double acting type
Single acting push type
Single acting pull type
Double acting double rod type
Page where dimensions are
shown
101
Page where dimensions are
shown
104
Page where dimensions are
shown
107
Page where dimensions are
shown
110
BDA
BSA
BTA
BDAD
Mass
g [oz.]
Mass of side mount
Operation Bore size
type
mm [in.]
Double acting type
6
[0.236]
10
[0.394]
Single acting pull type
Single acting push type
16
[0.630]
6
[0.236]
10
[0.394]
16
[0.630]
6
[0.236]
10
[0.394]
16
[0.630]
Stroke
mm
Standard
cylinder
Cylinder
with
magnet
5
21 [0.74] 24 [0.85]
10
24 [0.85] 27 [0.95]
15
27 [0.95] 30 [1.06]
20
30 [1.06] 33 [1.16]
25
33 [1.16] 36 [1.27]
30
36 [1.27] 39 [1.38]
5
37 [1.31] 43 [1.52]
10
41 [1.45] 47 [1.66]
15
45 [1.59] 51 [1.80]
20
49 [1.73] 55 [1.94]
25
53 [1.87] 59 [2.08]
30
57 [2.01] 63 [2.22]
5
79 [2.79] 92 [3.25]
10
86 [3.03] 99 [3.49]
15
93 [3.28] 106 [3.74]
20
100 [3.53] 113 [3.99]
25
107 [3.77] 120 [4.23]
30
114 [4.02] 127 [4.48]
5
25 [0.88] 28 [0.99]
10
28 [0.99] 31 [1.09]
15
31 [1.09] 34 [1.20]
5
43 [1.52] 49 [1.73]
10
47 [1.66] 53 [1.87]
15
51 [1.80] 57 [2.01]
5
90 [3.17] 103 [3.63]
10
97 [3.42] 110 [3.88]
15
104 [3.67] 117 [4.13]
5
27 [0.95] 30 [1.06]
10
30 [1.06] 33 [1.16]
15
33 [1.16] 36 [1.27]
5
46 [1.62] 52 [1.83]
10
50 [1.76] 56 [1.98]
15
54 [1.90] 60 [2.12]
5
100 [3.53] 113 [3.99]
10
107 [3.77] 120 [4.23]
15
114 [4.02] 127 [4.48]
Additional mass
With 1 sensor switch
Double (Only for cylinder with magnet type)
rod
ZC130□ ZC153□ CS5T□ CS11T□
Rod side mounting bracket
Head side mounting bracket
Foot A
mount
Flange A
mount
Flange B
mount
Foot A
mount
Flange A
mount
Flange B
mount
4 [0.14]
20 [0.71]
10 [0.35]
1 [0.04]
1 [0.04]
15 [0.53]
5 [0.18]
5 [0.18]
8 [0.28]
20 [0.71]
16 [0.56]
2 [0.07]
2 [0.07]
24 [0.85]
8 [0.28]
8 [0.28]
16 [0.56]
20 [0.71]
33 [1.16]
4 [0.14]
4 [0.14]
53 [1.87] 17 [0.60] 17 [0.60]
−
20 [0.71]
10 [0.35]
1 [0.04]
1 [0.04]
15 [0.53]
5 [0.18]
5 [0.18]
−
20 [0.71]
16 [0.56]
2 [0.07]
2 [0.07]
24 [0.85]
8 [0.28]
8 [0.28]
−
20 [0.71]
33 [1.16]
4 [0.14]
4 [0.14]
53 [1.87] 17 [0.60] 17 [0.60]
−
20 [0.71]
10 [0.35]
1 [0.04]
1 [0.04]
15 [0.53]
5 [0.18]
5 [0.18]
−
20 [0.71]
16 [0.56]
2 [0.07]
2 [0.07]
24 [0.85]
8 [0.28]
8 [0.28]
−
20 [0.71]
33 [1.16]
4 [0.14]
4 [0.14]
53 [1.87] 17 [0.60] 17 [0.60]
Calculation example: To add 2 sensor switches to the cylinder with magnet, double acting type BDAS10×20,
55＋(20×2)＝95g [3.35oz.]
Remark: There are 2 types of sensor switch lead wire lengths.
A: 1000mm [39in.], B: 3000mm [118in.]
Order Codes for Standard Cylinders
■ Cylinder
specification
■ System
■ Mounting type ■ Sensor switch
(Made to order)
(Rod side)
Side mount
Blank:
Standard
specifications
NCU:
Non-ion
specification
●With
Blank
countermeasure
for non generating
copper ion
Foot A mount
●Made to order
Blank:
Standard
cylinderNote1
S : Cylinder with
magnet
-1A
Flange A mount
■ Number of
sensor switches
■ Lead wire
length
No sensor switch
A : 1000mm
[39in.]
B : 3000mm
[118in.]
No sensor switch
Blank
Blank
With ZC130
With 1 sensor
switch
With CS5T
-ZC130
-CS5T
1
●Solid state type
●With indicator lamp
●DC10〜28V
●2-lead wire
●Reed switch type
●Without indicator
lamp
●DC5〜28V
AC85〜115V
With ZC153
With CS11T
With 2 sensor
switches
-3A
Flange B
mount Note2
-3B
BDA
Single acting push type
BSA
Single acting pull type
BTA
Double acting
double rod type
BDAD
-ZC153
-CS11T
●Solid state type
●With indicator lamp
●DC4.5〜28V
●3-lead wire
●Reed switch type
●With indicator lamp
●DC10〜28V
Bore size × Stroke
Basic type
Double acting type
2
×
S
Notes: 1. The magnet for the sensor switch is not built-in.
Always use the cylinder with magnet when
using the sensor switch.
2. Two sensor switches cannot be installed on a
cylinder with flange B mount.
Mount 1 sensor switch on the head side when
the flange B mount is used on the rod side, and
mount 1 sensor switch on the rod side when the
flange B mount is used on the head side.
-1A
-3A
-3B
-NCU
-ZC130
-ZC153
-CS5T
-CS11T
A
B
1
2
● For the order codes of
sensor switches only, see
p.126.
● In the 5mm [0.197in.]
cylinder strokes, 1 sensor
switch installation is
standard for CS5T and
CS11T. When mounting 2
units, use the solid state
type.
● For details, see p.1544.
● See table for operation type, bore
size and stroke.
● Order the head side mounting bracket
separately.
Cannot be ordered as already assembled the
mount on the cylinder.
● For the order codes of mounting brackets only,
see p.125.
Remark: For the cylinder joint and cylinder rod end
mounted on the piston rod end, see p.1568.
● In the 5mm [0.197in.] cylinder strokes, 1 sensor switch installation is standard for the reed switch type (CS5T, CS11T).
Additional Parts (To be ordered separately)
Mounting brackets
Shield plate
Operation Type, Bore Size, and Stroke
Operation type
Bore size
Double acting
type
10
Standard strokes
6
5, 10, 15, 20, 25, 30
16
● Side mount ● Foot A mount ● Flange A
(Head cover)
mount
● Flange B
mount
● The photographs above show head side mounting brackets.
● For the order codes, see p.125.
● Comes with 2 mounting screws.
● For cylinder with
magnet.
● For the order code, see
p.128.
● Comes with 2 mounting
screws.
Single acting
push type
Single acting
pull type
10
Double acting
double rod type
10
6
5, 10, 15
16
6
16
5, 10, 15, 20, 25, 30
mm
Inner Construction and Major Parts
●Double acting type
BDA
w
i
r !1
!2
q
o
●Single acting push type
BSA
!5
!7
!3 y e
t
!4
●Single acting pull type
BTA
u
●Cylinder with magnet double acting type
BDAS
!8
!0
!6
!7
!5
Major Parts and Materials
No.
●Double acting double rod type
BDAD
!9
Parts
Materials
Standard specification
Non-ion specification
q
q
Body
Aluminum alloy (anodized)
w
w
Rod cover Note
PBT
Aluminum alloy (black anodized)
e
e
Head cover Note
PBT
Aluminum alloy (black anodized)
r
r
Rod bushing
Oil impregnated bronze
t
t
Piston rod
Stainless steel
y
y
Piston
Brass
u
u
Piston seal
Synthetic rubber (NBR)
i
i
Rod end nut
Steel (electric nickel plated)
o
o
Seal case
Brass
!0
!0
Cap
Polyacetal
←
!1
!1
Rod seal
Synthetic rubber (NBR)
←
!2
!2
O-ring
Synthetic rubber (NBR)
←
!3
!3
Bumper
Synthetic rubber (NBR)
←
!4
!4
Spring
Steel (zinc plated)
!5
!5
Spring holder
Brass
Aluminum
!6
!6
Collar
Brass
Aluminum
!7
!7
Filter
Foamed metal
!8
!8
Support
Brass
!9
!9
Magnet
←
Special steel
←
Aluminum
←
←
Special steel
←
←
Aluminum
φ6: Sintered alloy magnet
φ10 ·φ16: Plastic magnet
←
Note: Only the foot A mount is steel (black zinc plated).
Flange A and flange B mounts are aluminum alloy (black anodized).
Seals
Parts
Bore size
mm [in.]
Rod seal
Piston seal
O-ring
6 [0.236]
NY-6×3×2
COP-6L
8.4×6×1.2
10 [0.394]
NY-8×5×2
COP-10L
10×7.6×1.2
16 [0.630]
NY-9×6×2
COP-16L
16×13×1.5
Dimensions of Double Acting Type (mm)
● Side mount BDA
Bore size × Stroke
BDA- Bore size
φV
Piston rod diameter
N
N
1.6
D＋Stroke
2-M5×0.8
φ10, φ16
φ10, φ16
A＋Stroke
B
T
C＋Stroke
1
I
G
11
U
G
R
H
Q
Y
S
O
J
K
2-P
φL
W
4-M3×0.5 (Both sides)
Z
M＋Stroke
X
φ6
T
φ6
10
Type
Code
R
Q
10
S
I
Standard cylinder Cylinder with magnet
A
C
D
M
B
G
H
I
Bore
mm [in.]
6 [0.236]
38 28
8
12 43 33 13 17 10
5
7
5.5 1.8 M3×0.5
10 [0.394] 43 30
7
13 48 35 12 18 13
6
10
7
2.4 M4×0.7
16 [0.630] 48 33
8
15 53 38 13 20 15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
A
C
D
M
J
K
L
Q
R
S
10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15
7
20 12
8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18
8
24 14 10.5 5
6 –0
–0.05
N
O
P
T
U
V
3
6
W
6.5
X
Y
Z
26 12 16
30 16 17
7.5 33 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Double Acting Type (mm)
● Foot A mount BDA
Bore size × Stroke -1A
BDA- Bore size
MULTI-1A
φV
Piston rod diameter
N
N
1.6
D＋Stroke
2-M5×0.8
φ6
φ10, φ16
A＋Stroke
T
B
T
10
I
C＋Stroke
1
I
U
G
G
H
φL
K
G
G
AH
AH
AC
AC
O
10
J
4-M3×0.5 (Both sides)
AF
11＋W
AG
AF
2-φAP
AD
AA＋Stroke
AB
Standard cylinder
Cylinder with magnet
Bore
mm [in.]
A
C
D
AA
A
C
D
AA
6 [0.236]
38
28
8
32
43
33
13
10 [0.394] 43
30
7
34
48
35
16 [0.630] 48
33
8
38
53
38
Type
Code
B
G
H
I
J
K
L
N
O
T
37
10
5
7
5.5 1.8 M3×0.5
6 –0
–0.05
12
39
13
6
10
7
2.4 M4×0.7
10
14
12
13
43
15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19
8 –0
–0.05 11.5 15
U
V
3
14 10.5 5
20
6
W
AB AC AD AF AG AH AP
6
26
13
6
9
16
9
31
14
8
10
19
7.5 10 41.5 17
12
12
25 4.5
6.5
3.5
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Double Acting Type (mm)
● Flange A mount BDA
Bore size × Stroke -3A
BDA- Bore size
MULTI-3A
φV
Piston rod diameter
N
N
1.6
D＋Stroke
2-M5×0.8
φ6
φ10, φ16
A＋Stroke
T
B
T
10
I
C＋Stroke
1
I
U
G
G
H
BH
BH
BC
BC
O
10
J
K
φL
BG
BG
4-M3×0.5 (Both sides)
2-φAP
AF
● Flange B mount BDA
BB
2-φAP
AF
11＋W
Bore size × Stroke -3B
BDA- Bore size
MULTI-3B
φV
N
N
D＋Stroke
1.6
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋Stroke
B
T
T
2-φAP
2-φAP
C＋Stroke
1
I
I
G
U
G
H
O
S
BI
S
BI
J
K
BF
BF
BE
Type
Code
φL
BE
BB
4-M3×0.5 (Both sides)
11＋W
Standard cylinder Cylinder with magnet
B
G
H
I
N
O
S
T
13
10
5
7
5.5 1.8 M3×0.5 6 –0
–0.05 10
14
20
12
35
12
13
6
10
7
2.4 M4×0.7 8 –0
–0.05 11.5 15
24
14 10.5 5
38
13
15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19
33
20
Bore
mm [in.]
A
C
D
A
C
D
6 [0.236]
38
28
8
43
33
10 [0.394] 43
30
7
48
16 [0.630] 48
33
8
53
J
K
L
U
V
3
6
W
6.5
AF AP BB BC BE BF BG BH
6
8
3.5
15 27.5 24
18
19 31.5 26
20
7.5 12 4.5 22
42
36
3.5
14
16
28 4.5 21
BI
5
6
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Single Acting Push Type (mm)
● Side mount BSA
Bore size × Stroke
BSA- Bore size
φV
Piston rod diameter
0.8
N
M5×0.8
φ10, φ16
φ10, φ16
A＋Stroke
B
T
C＋Stroke
1
I
G
11
U
G
R
H
Q
Y
S
O
J
K
2-P
φL
W
4-M3×0.5 (Both sides)
Z
M＋Stroke
X
φ6
T
φ6
10
Type
Code
R
Q
10
S
I
Standard cylinder Cylinder with magnet
A
B
G
H
I
Bore
mm [in.]
6 [0.236]
43 33 17 48 38 22 10
5
7
5.5 1.8 M3×0.5
10 [0.394] 48 35 18 53 40 23 13
6
10
7
2.4 M4×0.7
16 [0.630] 53 38 20 58 43 25 15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
C
M
A
C
M
J
K
L
Q
R
S
10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15
7
20 12
8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18
8
24 14 10.5 5
6 –0
–0.05
N
O
P
T
U
V
3
6
W
6.5
X
Y
Z
26 12 16
30 16 17
7.5 33 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Single Acting Push Type (mm)
● Foot A mount BSA
Bore size × Stroke -1A
BSA- Bore size
MULTI-1A
φV
N
0.8
Piston rod diameter
M5×0.8
φ6
φ10, φ16
A＋Stroke
T
B
T
10
C＋Stroke
1
I
I
U
G
G
H
φL
K
G
G
AH
AH
AC
AC
O
10
J
4-M3×0.5
(Both sides)
AF
11＋W
AG
AF
2-φAP
AD
AA＋Stroke
AB
Type
Code
Standard cylinder Cylinder with magnet
B
G
H
I
42
10
5
7
40
44
13
6
10
43
48
15
7
12
Bore
mm [in.]
A
C
AA
A
C
AA
6 [0.236]
43
33
37
48
38
10 [0.394] 48
35
39
53
16 [0.630] 53
38
43
58
J
K
L
N
O
T
5.5 1.8
M3×0.5
7
2.4
8
3.2
U
V
6 –0
–0.05
10
14
12
M4×0.7
8 –0
–0.05
11.5 15
14 10.5 5
M5×0.8
10 –0
–0.05
12.5 19
20
3
6
W
AB AC AD AF AG AH AP
6
26
13
6
9
16
9
31
14
8
10
19
7.5 10 41.5 17
12
12
25 4.5
6.5
3.5
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Single Acting Push Type (mm)
● Flange A mount BSA
Bore size × Stroke -3A
BSA- Bore size
MULTI-3A
φV
Piston rod diameter
0.8
N
M5×0.8
φ6
φ10, φ16
A＋Stroke
T
B
T
10
C＋Stroke
1
I
I
U
G
G
H
BH
BH
BC
BC
O
10
J
K
φL
BG
BG
4-M3×0.5 (Both sides)
2-φAP
AF
● Flange B mount BSA
BB
2-φAP
AF
11＋W
Bore size × Stroke -3B
BSA- Bore size
MULTI-3B
N
φV
0.8
Piston rod diameter
M5×0.8
φ6
φ10, φ16
A＋Stroke
B
T
T
2-φAP
2-φAP
C＋Stroke
1
I
I
U
G
G
H
O
S
BI
S
BI
J
K
BF
BE
Type
Code
φL
BF
BB
BE
4-M3×0.5 (Both sides)
11＋W
Standard cylinder Cylinder with magnet
B
G
H
I
38
10
5
7
53
40
13
6
10
58
43
15
7
12
Bore
mm [in.]
A
C
A
C
6 [0.236]
43
33
48
10 [0.394] 48
35
16 [0.630] 53
38
J
N
O
S
T
6 –0
–0.05
10
14
20
12
M4×0.7
8 –0
–0.05
11.5 15
24
14 10.5 5
M5×0.8
10 –0
–0.05
12.5 19
33
20
K
L
5.5 1.8
M3×0.5
7
2.4
8
3.2
U
V
3
6
W
6.5
AF AP BB BC BE BF BG BH
6
8
3.5
15 27.5 24
18
19 31.5 26
20
7.5 12 4.5 22
42
36
3.5
14
16
28 4.5 21
BI
5
6
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Single Acting Pull Type (mm)
● Side mount BTA
Bore size × Stroke
BTA- Bore size
N
0.8
φV
Piston rod diameter
M5×0.8
φ10, φ16
φ10, φ16
A＋
（Stroke×2）
C＋Stroke
B＋Stroke
T
I
1
H
G
U
11
G
R
Q
Y
S
O
J
K
φL
2-P
W
Z
4-M3×0.5 (Both sides)
M＋Stroke
X＋Stroke
φ6
T
φ6
10
R
Type
Code
Q
10
S
I
Standard cylinder Cylinder with magnet
A
B
G
H
I
Bore
mm [in.]
6 [0.236]
43 33 17 48 38 22 10
5
7
5.5 1.8 M3×0.5
10 [0.394] 48 35 18 53 40 23 13
6
10
7
2.4 M4×0.7
16 [0.630] 53 38 20 58 43 25 15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
C
M
A
C
M
J
K
L
Q
R
S
10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15
7
20 12
8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18
8
24 14 10.5 5
6 –0
–0.05
N
O
P
T
U
V
3
6
W
6.5
X
Y
Z
26 12 16
30 16 17
7.5 33 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Single Acting Pull Type (mm)
● Foot A mount BTA
Bore size × Stroke -1A
BTA- Bore size
MULTI-1A
N
0.8
φV
Piston rod diameter
M5×0.8
φ6
φ10, φ16
（Stroke×2）
A＋
T
H
I
I
C＋Stroke
B＋Stroke
T
10
1
U
G
G
AC
AC
O
10
J
AH
AH
φL
G
K
G
4-M3×0.5 (Both sides)
AF
11＋W
AG
AF
2-φAP
AD
AB＋Stroke
Standard cylinder
Cylinder with magnet
Bore
mm [in.]
A
C
AA
A
C
AA
6 [0.236]
43
33
37
48
38
10 [0.394] 48
35
39
53
16 [0.630] 53
38
43
58
Type
Code
B
G
H
I
42
10
5
7
40
44
13
6
10
43
48
15
7
12
J
K
L
5.5 1.8
M3×0.5
7
2.4
8
3.2
AA＋Stroke
N
O
T
U
V
6 –0
–0.05
10
14
12
M4×0.7
8 –0
–0.05
11.5 15
14 10.5 5
M5×0.8
10 –0
–0.05
12.5 19
20
3
6
W
AB AC AD AF AG AH AP
6
26
13
6
9
16
9
31
14
8
10
19
7.5 10 41.5 17
12
12
25 4.5
6.5
3.5
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Single Acting Pull Type (mm)
● Flange A mount BTA
Bore size × Stroke -3A
BTA- Bore size
MULTI-3A
φV
N
0.8
Piston rod diameter
M5×0.8
φ6
φ10, φ16
A＋
（Stroke× 2 ）
T
B＋Stroke
T
10
I
C＋Stroke
H
I
1
G
U
G
φL
BH
BH
BC
BC
O
10
J
K
2-φAP
AF
BG
BG
4-M3×0.5 (Both sides)
● Flange B mount BTA
BB＋Stroke
2-φAP
AF
11＋W
Bore size × Stroke -3B
BTA- Bore size
MULTI-3B
φV
N
0.8
Piston rod diameter
M5×0.8
φ6
φ10, φ16
A＋
（Stroke× 2 ）
T
2-φAP
2-φAP
C＋Stroke
B＋Stroke
T
H
I
1
G
U
G
I
O
S
BI
S
BI
J
φL
BF
BF
BE
Type
Code
K
4-M3×0.5 (Both sides)
11＋W
BB＋Stroke
BE
Standard cylinder Cylinder with magnet
B
G
H
I
38
10
5
7
40
13
6
10
7
Bore
mm [in.]
A
C
A
C
6 [0.236]
43
33
48
10 [0.394] 48
35
53
16 [0.630] 53
38
58
43
15
7
12
N
O
S
T
6 –0
–0.05
10
14
20
12
M4×0.7
8 –0
–0.05
11.5 15
24
14 10.5 5
M5×0.8
10 –0
–0.05
12.5 19
33
20
K
L
5.5 1.8
M3×0.5
2.4
8
J
3.2
U
V
3
6
W
6.5
AF AP BB BC BE BF BG BH
6
8
3.5
15 27.5 24
18
19 31.5 26
20
7.5 12 4.5 22
42
36
3.5
14
16
28 4.5 21
BI
5
6
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Double Acting Double Rod Type (mm)
● Side mount BDAD
Bore size × Stroke
BDAD- Bore size
N
φV
N
D＋Stroke
1.6
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋
（Stroke× 2 ）
T
B
T
10
1
I
I
B＋Stroke
C＋Stroke
G
11
U
G
1
H
O
Y
S
S
10
J
Y
Z
K
2-P
4-M3×0.5 (Both sides) φL
W
M＋Stroke
Z
X
Type
Code
Standard cylinder Cylinder with magnet
A
C
D
M
B
G
H
I
Bore
mm [in.]
6 [0.236]
48 28
8
12 53 33 13 17 10
5
7
5.5 1.8 M3×0.5
10 [0.394] 56 30
7
13 61 35 12 18 13
6
10
7
2.4 M4×0.7
16 [0.630] 63 33
8
15 68 38 13 20 15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 33 20
A
C
D
M
J
K
L
6 –0
–0.05
N
O
P
S
T
10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 20 12
U
V
3
8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 24 14 10.5 5
6
W
6.5
X
26 12 16
30 16 17
7.5 33 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Double Acting Double Rod Type (mm)
● Foot A mount BDAD
Bore size × Stroke -1A
BDAD- Bore size
MULTI-1A
D＋Stroke
N
φV
N
1.6
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋
（Stroke× 2 ）
T
10
1
I
I
B＋Stroke
C＋Stroke
B
T
G
U
G
1
H
AH
AH
AC
AC
O
10
J
G
K
G
4-M3×0.5 (Both sides) φL
AF
11＋W
AG
AF
2-φAP
AD
（Stroke× 2 ）
AA＋
AB
Standard cylinder
Cylinder with magnet
Bore
mm [in.]
A
C
D
AA
A
C
D
AA
6 [0.236]
48
28
8
42
53
33
13
10 [0.394] 56
30
7
47
61
35
16 [0.630] 63
33
8
53
68
38
Type
Code
B
G
H
I
J
K
L
N
O
T
47
10
5
7
5.5 1.8 M3×0.5
6 –0
–0.05
12
52
13
6
10
7
2.4 M4×0.7
10
14
12
13
58
15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19
8 –0
–0.05 11.5 15
U
V
3
14 10.5 5
20
6
W
AB AC AD AF AG AH AP
6
26
13
6
9
16
9
31
14
8
10
19
7.5 10 41.5 17
12
12
25 4.5
6.5
3.5
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Double Acting Double Rod Type (mm)
● Flange A mount BDAD
Bore size × Stroke -3A
BDAD- Bore size
MULTI-3A
N
φV
N
D＋Stroke
1.6
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋
（Stroke× 2 ）
T
B
T
10
1
I
I
C＋Stroke
B＋Stroke
G
U
G
1
H
BH
BH
BC
BC
O
10
J
K
2-φAP
AF
BG
BG
4-M3×0.5 (Both sides) φL
● Flange B mount BDAD
BB
2-φAP
AF
11＋W
Bore size × Stroke -3B
BDAD- Bore size
MULTI-3B
N
φV
N
D＋Stroke
1.6
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋
（Stroke× 2 ）
B
T
T
2-φAP
2-φAP
C＋Stroke
1
I
I
G
B＋Stroke
U
G
1
H
O
BI
S
S
BI
J
K
BF
Type
Code
BB
BF
BE
4-M3×0.5 (Both sides) φL
11＋W
BE
Standard cylinder Cylinder with magnet
B
G
H
I
N
O
S
T
13
10
5
7
5.5 1.8 M3×0.5 6 –0
–0.05 10
14
20
12
35
12
13
6
10
7
2.4 M4×0.7 8 –0
–0.05 11.5 15
24
14 10.5 5
38
13
15
7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19
33
20
Bore
mm [in.]
A
C
D
A
C
D
6 [0.236]
48
28
8
53
33
10 [0.394] 56
30
7
61
16 [0.630] 63
33
8
68
J
K
L
U
V
3
6
W
6.5
AF AP BB BC BE BF BG BH
6
8
3.5
15 27.5 24
18
19 31.5 26
20
7.5 12 4.5 22
42
36
3.5
14
16
28 4.5 21
BI
5
6
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
MULTI MOUNT CYLINDERS
Non-rotating Cylinders
Symbols
● Double acting type (BDAL)
● Single acting push type
(BSAL)
Specifications
Bore size mm [in.]
6 [0.236]
Item
● Single acting pull type (BTAL) ● Double acting double rod
type (BDADL)
Media
16 [0.630]
Air
Operating
pressure range
Cylinder Thrust
10 [0.394]
MPa
[psi.]
Double acting
type
0.2〜0.7
[29〜102]
0.15〜0.7
[22〜102]
0.1〜0.7
[15〜102]
Single acting
push type
0.25〜0.7
[36〜102]
0.2〜0.7
[29〜102]
0.15〜0.7
[22〜102]
Single acting
pull type
0.35〜0.7
[51〜102]
0.25〜0.7
[36〜102]
0.2〜0.7
[29〜102]
Double acting
double rod type
0.2〜0.7
[29〜102]
0.15〜0.7
[22〜102]
0.1〜0.7
[15〜102]
N [lbf.]
Pressure
Air pressure MPa [psi.]
Operation
area
mm2 0.1 0.2 0.3 0.4 0.5 0.6 0.7
type
[in.2] [15] [29] [44] [58] [73] [87] [102]
28.2
5.6 8.5 11.3 14.1 16.9 19.7
Push side [0.0437] − [1.26] [1.91] [2.54] [3.17] [3.80] [4.43]
Double
Bore size Piston rod
diameter
mm [in.] mm [in.]
acting type
6
3
[0.236] [0.118]
21.2
[0.0329]
4.2 6.4 8.5 10.6 12.7 14.8
− [0.94] [1.44] [1.91] [2.38] [2.85] [3.33]
28.2
Single acting push type
[0.0437]
5.6 8.5 11.3 14.1 16.9 19.7
− [1.26] [1.91] [2.54] [3.17] [3.80] [4.43]
Pull side
Single acting pull type
Double
acting type
10
5
[0.394] [0.197]
−
−
6.4 8.5 10.6 12.7 14.8
[1.44] [1.91] [2.38] [2.85] [3.33]
Push side
78.5
7.9 15.7 23.6 31.4 39.3 47.1 55
[0.1217] [1.78] [3.53] [5.31] [7.06] [8.83] [10.59] [12.36]
Pull side
58.9
5.9 11.8 17.7 23.6 29.5 35.3 41.2
[0.0913] [1.33] [2.65] [3.98] [5.31] [6.63] [7.94] [9.26]
Non-rotating accuracy
Stroke tolerance
Stroke
mm
Standard strokes
10
5, 10, 15, 20, 25, 30
16
6
Single acting push type
Single acting pull type
10
5, 10, 15
16
6
Double acting
double rod type
10
16
End of stroke
5
10
15
5, 10, 15
3.9 [0.88]
2.9 [0.65]
2.0 [0.45]
4.9 [1.10]
10 [0.394]
6.9 [1.55]
4.9 [1.10]
2.9 [0.65]
9.8 [2.20]
16 [0.630]
17.7 [3.98] 13.7 [3.08] 9.8 [2.20]
21.6 [4.86]
6 [0.236]
Bore size
6
N [lbf.]
Zero stroke
+1 +0.039
]
0 [+ 0
mm [in.]
mm
Spring Return Force (Only for Single Acting Type)
Item
±1°
Operation Type, Bore Size, and Stroke
172 17.2 34.4 51.6 68.8 86 103.2 120.4
Pull side
[0.267] [3.87] [7.73] [11.60] [15.47] [19.33] [23.20] [27.07]
Note: For the double acting double rod type, see the double acting type pull side.
±1.5°
M5×0.8
Double acting type
Single acting pull type
±2°
Port size
201 20.1 40.2 60.3 80.4 100.5 120.6 140.7
Push side [0.312]
[4.52] [9.04] [13.56] [18.07] [22.59] [27.11] [31.63]
34.4 51.6 68.8 86 103.2 120.4
− [7.73] [11.60] [15.47] [19.33] [23.20] [27.07]
(If lubrication is required,
use Turbine Oil Class 1 [ISO VG32] or equivalent.)
Lubrication
Operation type
172
[0.267]
50〜500 [2.0〜19.7]
Rubber bumper
Not required
11.8 17.7 23.6 29.5 35.3 41.2
− [2.65] [3.98] [5.31] [6.63] [7.94] [9.26]
40.2 60.3 80.4 100.5 120.6 140.7
− [9.04] [13.56] [18.07] [22.59] [27.11] [31.63]
0〜60 [32〜140]
Cushion
58.9
Single acting pull type [0.0913]
201
Single acting push type [0.312]
1.03 [149]
°C [°F]
Operating speed range mm/s [in./sec.]
15.7 23.6 31.4 39.3 47.1 55
− [3.53] [5.31] [7.06] [8.83] [10.59] [12.36]
Bore size mm [in.]
MPa [psi.]
Operating temperature range
78.5
[0.1217]
Single acting push type
Double
acting type
16
6
[0.630] [0.236]
21.2
[0.0329]
Proof pressure
5, 10, 15, 20, 25, 30
Double acting type
Single acting push type
Single acting pull type
Double acting double rod type
Page where dimensions are
shown
117
Page where dimensions are
shown
119
Page where dimensions are
shown
121
Page where dimensions are
shown
123
BDAL
BSAL
BTAL
BDADL
Mass
g [oz.]
Mass of side mount
Operation Bore size
type
mm [in.]
Double acting type
6
[0.236]
10
[0.394]
Single acting pull type
Single acting push type
16
[0.630]
6
[0.236]
10
[0.394]
16
[0.630]
6
[0.236]
10
[0.394]
16
[0.630]
Stroke
mm
Standard
cylinder
Cylinder
with
magnet
5
31 [1.09] 34 [1.20]
10
34 [1.20] 37 [1.31]
15
37 [1.31] 40 [1.41]
20
40 [1.41] 43 [1.52]
25
43 [1.52] 46 [1.62]
30
46 [1.62] 49 [1.73]
5
51 [1.80] 57 [2.01]
10
55 [1.94] 61 [2.15]
15
59 [2.08] 65 [2.29]
20
63 [2.22] 69 [2.43]
25
67 [2.36] 73 [2.57]
30
71 [2.50] 77 [2.72]
5
104 [3.67] 117 [4.13]
10
111 [3.92] 124 [4.37]
15
118 [4.16] 131 [4.62]
20
125 [4.41] 138 [4.87]
25
132 [4.66] 145 [5.11]
30
139 [4.90] 152 [5.36]
5
35 [1.23] 38 [1.34]
10
38 [1.34] 41 [1.45]
15
41 [1.45] 44 [1.55]
5
57 [2.01] 63 [2.22]
10
61 [2.15] 67 [2.36]
15
65 [2.29] 71 [2.50]
5
115 [4.06] 128 [4.51]
10
122 [4.30] 135 [4.76]
15
129 [4.55] 142 [5.01]
5
37 [1.31] 40 [1.41]
10
40 [1.41] 43 [1.52]
15
43 [1.52] 46 [1.62]
5
60 [2.12] 66 [2.33]
10
64 [2.26] 70 [2.47]
15
68 [2.40] 74 [2.61]
5
125 [4.41] 138 [4.87]
10
132 [4.66] 145 [5.11]
15
139 [4.90] 152 [5.36]
Additional mass
Double
rod
With 1 sensor switch
(including mounting bracket)
Rod side mounting bracket
Head side mounting bracket
Foot A Note Flange A
mount
ZC130□ ZC153□ CS5T□ CS11T□ mount
Flange B
mount
Foot A
mount
Flange A
mount
Flange B
mount
4 [0.14]
20 [0.71]
10 [0.35]
1 [0.04]
1 [0.04]
15 [0.53]
5 [0.18]
5 [0.18]
8 [0.28]
20 [0.71]
16 [0.56]
2 [0.07]
2 [0.07]
24 [0.85]
8 [0.28]
8 [0.28]
16 [0.56]
20 [0.71]
33 [1.16]
4 [0.14]
4 [0.14]
53 [1.87] 17 [0.60] 17 [0.60]
−
20 [0.71]
−
1 [0.04]
1 [0.04]
15 [0.53]
5 [0.18]
5 [0.18]
−
20 [0.71]
−
2 [0.07]
2 [0.07]
24 [0.85]
8 [0.28]
8 [0.28]
−
20 [0.71]
−
4 [0.14]
4 [0.14]
53 [1.87] 17 [0.60] 17 [0.60]
−
20 [0.71]
−
1 [0.04]
1 [0.04]
15 [0.53]
5 [0.18]
5 [0.18]
−
20 [0.71]
−
2 [0.07]
2 [0.07]
24 [0.85]
8 [0.28]
8 [0.28]
−
20 [0.71]
−
4 [0.14]
4 [0.14]
53 [1.87] 17 [0.60] 17 [0.60]
Note: Can be installed only on the opposite the rod side with the non-rotation plate of a double rod cylinder.
Calculation example: To add 2 sensor switches to the cylinder with magnet, double acting type BDALS10×20,
69＋(20×2)＝109g [3.84oz.]
Remark: There are 2 types of sensor switch lead wire lengths.
A: 1000mm [39in.], B: 3000mm [118in.]
Order Codes for Non-rotating Cylinders
■ Cylinder
specification
■ System
■ Mounting type ■ Sensor switch
(Made to order)
(Rod side)
Side mount
Blank:
Standard
specifications
NCU:
Non-ion
specification
●With
Blank
countermeasure
for non generating
copper ion
Flange A mount
●Made to order
Blank:
Standard
cylinder Note1
S : Cylinder with
magnet
-3A
Flange B
mountNote2
■ Number of
Sensor switches
■ Lead wire
length
No sensor switch
A : 1000mm
[39in.]
B : 3000mm
[118in.]
No sensor switch
Blank
Blank
With ZC130
With 1 sensor
switch
With CS5T
-ZC130
-CS5T
1
●Solid state type
●With indicator lamp
●DC10〜28V
●2-lead wire
●Reed switch type
●Without indicator
lamp
●DC5〜28V
AC85〜115V
With ZC153
With CS11T
With 2 sensor
switches
-3B
2
-ZC153
-CS11T
●Solid state type
●With indicator lamp
●DC4.5〜28V
●3-lead wire
Bore size × Stroke
Basic type
Double acting type
BDAL
Single acting push type
BSAL
Single acting pull type
BTAL
Double acting
double rod type
BDADL
●Reed switch type
●With indicator lamp
●DC10〜28V
×
S
Notes: 1. The magnet for the sensor switch is not built in.
Always use the cylinder with magnet when using
the sensor switch.
2. Two sensor switches cannot be mounted on a
cylinder with flange B mount.
Mount 1 sensor switch on the head side when the
flange B mount is used on the rod side, and
mount 1 sensor switch on the rod side when the
flange B mount is used on the head side.
-ZC130
-ZC153
-CS5T
-CS11T
-3A
-3B
-NCU
A
B
1
2
● For the order codes of
sensor switches only, see
p.126.
● Order the head side mounting bracket
● In the 5mm [0.197in.]
separately.
cylinder strokes, 1 sensor
Cannot be ordered as already assembled
switch installation is
the mount on the cylinder.
standard for CS5T and
● For the order codes of mounting brackets
CS11T. When mounting 2
only, see p.125.
units, use the solid state
Remark: For the cylinder joint and cylinder rod end
type.
mounted on the piston rod end, see p.1568.
● For details, see p.1544.
● In the 5mm [0.197in.] cylinder strokes, 1 sensor switch is standard for the reed switch type (CS5T, CS11T).
● See table for operation type, bore
size and stroke.
Additional Parts (To be ordered separately)
Mounting brackets
Shield plate
Operation Type, Bore Size, and Stroke
Operation type
Bore size
Double acting
type
10
Standard strokes
6
5, 10, 15, 20, 25, 30
16
● Side mount ● Foot A mount ● Flange A
(Head cover)
mount
● Flange B
mount
● The photographs above show head side mounting brackets.
● For the order codes, see p.125.
● Comes with 2 mounting screws.
● For cylinder with magnet.
● For the order code, see
p.128.
● Comes with 2 mounting
screws.
Single acting
push type
Single acting
pull type
10
Double acting
double rod type
10
6
5, 10, 15
16
6
16
5, 10, 15, 20, 25, 30
mm
Inner Construction and Major Parts
●Double acting type
BDAL
r w
i
@0
!1
!2
q
@1 o
●Single acting push type
BSAL
!5
!7
!3 y e
t
!4
●Single acting pull type
BTAL
u
●Cylinder with magnet double acting type
BDALS
!8
!0
!6
Major Parts and Materials
!7
!5
No.
●Double acting double rod type
BDADL
!9
Parts
Materials
Standard specification
Non-ion specification
q
q
Body
Aluminum alloy (anodized)
←
w
w
Rod cover Note
Aluminum alloy (black anodized)
e
e
Head cover Note
PBT
←
Aluminum alloy (black anodized)
r
r
Rod bushing
Oil impregnated bronze
t
t
Piston rod
Stainless steel
y
y
Piston
Brass
u
u
Piston seal
Synthetic rubber(NBR)
i
i
Rod end nut
Steel (electric nickel plated)
o
o
Seal case
Brass
!0
!0
Cap
Polyacetal
←
!1
!1
Rod seal
Synthetic rubber (NBR)
←
!2
!2
O-ring
Synthetic rubber (NBR)
←
!3
!3
Bumper
Urethane rubber
←
!4
!4
Spring
Steel (zinc plated)
!5
!5
Spring holder
Brass
Aluminum
!6
!6
Collar
Brass
Aluminum
!7
!7
Filter
Foamed metal
!8
!8
Support
Brass
!9
!9
Magnet
@0
@0
Plate
Brass (electric nickel plated)
@1
@1
Guide pin
Stainless steel
Special steel
←
Aluminum
←
←
Special steel
←
←
Aluminum
φ6: Sintered alloy magnet
φ10, φ16: Plastic magnet
←
Steel (nickel plated)
←
Note: Only the foot A mount is steel (black zinc plated).
Seals
Parts
Bore size
mm [in.]
Rod seal
Piston seal
O-ring
6 [0.236]
NY-6×3×2
COP-6L
8.4×6×1.2
10 [0.394]
NY-8×5×2
COP-10L
10×7.6×1.2
16 [0.630]
NY-9×6×2
COP-16L
16×13×1.5
Dimensions of Non-rotating Double Acting Type (mm)
● Side mount BDAL
Bore size × Stroke
φV
BDAL- Bore size
N
N
D＋Stroke
1.6
Piston rod diameter
2-M5×0.8
φ10, φ16
φ10, φ16
A＋Stroke
B
T
C＋Stroke
1
G
6
4-M3×0.5 (Both sides)
E
I
U
11
G
R
H
Q
Y
XZ
CD
S
O
CE
J
CF
CG
K
2-P
W
Z
M＋Stroke
YZ
φCP
X＋Stroke
φ6
T
φ6
10
I
Q
XZ
CD
S
10
CE
R
φCP
CF
CG
YZ
Type
Code
Bore
mm [in.]
Standard cylinder Cylinder with magnet
A
C
D
M
X
A
C
D
M
B
X
E
G
6 [0.236] 43 28 8 12 27 48 33 13 17 32 15 7.5 5
H
I
J
K
L
N
O
P
Q
R
S
T
7 5.5 1.8 M3×0.5 6 –0
–0.05 10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15 7 20 12
U
V W Y
3
10 [0.394] 48 30 7 13 31 53 35 12 18 36 18 10.5 6 10 7 2.4 M4×0.7 8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18 8 24 14 10.5 5
16 [0.630] 53 33 8 15 35 58 38 13 20 40 20 12.5 7 12 8 3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
Code
Bore
mm [in.]
CD
CE
CF
CG
CP
XZ
YZ
6 [0.236]
7.5
7.5
3.5
5.5
2.5
9.5
11
10 [0.394]
9
8.5
4
6.5
3
11.5
13
16 [0.630]
12.5
9
6
9.5
4
16
19
6.5
Z
12 16
16 17
6 7.5 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Double Acting Type (mm)
● Flange A mount BDAL
Bore size × Stroke -3A
BDAL- Bore size
MULTI-3A
φV
Piston rod diameter
N
D＋Stroke
1.6
N
2-M5×0.8
φ6
φ10, φ16
A＋Stroke
T
B
T
10
I
C＋Stroke
E
I
1
G
G
U
H
XZ
BC
BH
BH
XZ
BC
O
10
J
K
BG
BG
11＋W
2-φAP
AF
YZ
BB
YZ
● Flange B mount BDAL
4-M3×0.5 (Both sides)
6
2-φAP
AF
Bore size × Stroke -3B
BDAL- Bore size
MULTI-3B
φV
N
N
D＋Stroke
1.6
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋Stroke
B
T
T
2-φAP
2-φAP
C＋Stroke
1
E
I
I
G
U
G
H
O
S
BI
XZ
XZ
S
BI
J
YZ
YZ
BF
BE
Type
Code
K
BF
6
BE
BB
4-M3×0.5 (Both sides)
11＋W
Standard cylinder Cylinder with magnet
N
O
S
T
D
A
G
H
I
6 [0.236]
43 28
8
48 33 13 15 7.5
5
7
5.5 1.8 M3×0.5
10 [0.394] 48 30
7
53 35 12 18 10.5 6
10
7
2.4 M4×0.7
16 [0.630] 53 33
8
58 38 13 20 12.5 7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 33 20
D
J
L
C
C
B
K
A
E
Bore
mm [in.]
6 –0
–0.05 10 14 20 12
U
V
3
8 –0
–0.05 11.5 15 24 14 10.5 5
6
W AF AP BB BC BE BF BG BH BI XZ YZ
6.5
6
8
3.5
20 27.5 24 18
24 31.5 26 20
3.5
14
16
7.5 12 4.5 27 42 36 28 4.5 21
5
6
9.5 11
11.5 13
16 19
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Single Acting Push Type (mm)
● Side mount BSAL
Bore size × Stroke
BSAL- Bore size
φV
N
0.8
Piston rod diameter
M5×0.8
φ10, φ16
φ10, φ16
A＋Stroke
B
T
C＋Stroke
1
G
6
4-M3×0.5 (Both sides)
E
I
U
11
G
R
H
Q
Y
XZ
CD
S
O
CE
J
φCP
CF
CG
K
W
2-P
Z
M＋Stroke
YZ
X＋Stroke
φ6
T
φ6
10
I
Q
XZ
CD
S
10
CE
R
φCP
CF
CG
YZ
Type
Code
Standard cylinder Cylinder with magnet
A
E
G
Bore
mm [in.]
6 [0.236]
48 33 17 32 53 38 22 37 15 7.5
C
X
M
A
C
M
X
B
H
I
J
K
N
O
P
Q
R
S
T
U
V
5
7
5.5 1.8 M3×0.5 10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15
7
20 12
10 [0.394] 53 35 18 36 58 40 23 41 18 10.5 6
10
7
2.4 M4×0.7 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18
8
24 14 10.5 5
16 [0.630] 58 38 20 40 63 43 25 45 20 12.5 7
12
8
3.2 M5×0.8 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
Code
Bore
mm [in.]
CD
CE
CF
CG
CP
XZ
YZ
6 [0.236]
7.5
7.5
3.5
5.5
2.5
9.5
11
10 [0.394]
9
8.5
4
6.5
3
11.5
13
16 [0.630]
12.5
9
6
9.5
4
16
19
3
6
W
6.5
Y
Z
12 16
16 17
7.5 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Single Acting Push Type (mm)
● Flange A mount BSAL
Bore size × Stroke -3A
BSAL- Bore size
MULTI-3A
φV
Piston rod diameter
0.8
N
M5×0.8
φ6
φ10, φ16
A＋Stroke
T
B
T
10
I
C＋Stroke
E
I
1
G
G
U
H
XZ
BC
BH
BH
XZ
BC
O
10
J
K
BG
BG
11＋W
2-φAP
AF
YZ
AF
BB
YZ
● Flange B mount BSAL
4-M3×0.5 (Both sides)
6
2-φAP
Bore size × Stroke -3B
BSAL- Bore size
MULTI-3B
φV
N
0.8
Piston rod diameter
M5×0.8
φ6
φ10, φ16
A＋Stroke
B
T
T
2-φAP
2-φAP
C＋Stroke
1
E
I
I
U
G
G
H
O
S
BI
XZ
XZ
S
BI
J
YZ
YZ
BF
BE
Type
Code
K
BF
6
BE
BB
11＋W
4-M3×0.5 (Both sides)
Standard cylinder Cylinder with magnet
Bore
mm [in.]
A
C
A
C
6 [0.236]
B
E
G
H
I
J
K
N
O
S
T
U
V
48
33
53
38
15 7.5
5
7
5.5 1.8 M3×0.5 10
14
20
12
10 [0.394] 53
35
58
40
18 10.5 6
10
7
2.4 M4×0.7 11.5 15
24
14 10.5 5
3
16 [0.630] 58
38
63
43
20 12.5 7
12
8
3.2 M5×0.8 12.5 19
33
20
6
W
6.5
AF AP BB BC BE BF BG BH
6
8
3.5
20 27.5 24
18
24 31.5 26
20
7.5 12 4.5 27
42
36
3.5
14
16
28 4.5 21
BI
5
6
XZ YZ
9.5 11
11.5 13
16
19
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Single Acting Pull Type (mm)
● Side mount BTAL
Bore size × Stroke
BTAL- Bore size
φV
Piston rod diameter
0.8
N
M5×0.8
φ10, φ16
φ10, φ16
（Stroke×2）
A＋
C＋Stroke
B＋Stroke
T
1
E
I
G
U
11
G
R
H
Q
Y
XZ
CD
S
O
CE
J
CF
CG
6
K
4-M3×0.5 (Both sides)
φL
W
2-P
M＋Stroke
YZ
φCP
Z
X＋
（Stroke×2）
φ6
T
φ6
10
I
φCP
Q
XZ
CD
S
10
CE
R
CF
CG
YZ
Type
Code
Standard cylinder Cylinder with magnet
A
E
G
Bore
mm [in.]
6 [0.236]
48 33 17 32 53 38 22 37 15 7.5
C
X
M
A
C
M
X
B
H
I
J
K
L
N
O
P
Q
R
S
T
U
V
5
7
5.5 1.8 M3×0.5
6 –0
–0.05 10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15
7
20 12
10 [0.394] 53 35 18 36 58 40 23 41 18 10.5 6
10
7
2.4 M4×0.7
8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18
8
24 14 10.5 5
16 [0.630] 58 38 20 40 63 43 25 45 20 12.5 7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
Code
Bore
mm [in.]
CD
CE
CF
CG
CP
XZ
YZ
6 [0.236]
7.5
7.5
3.5
5.5
2.5
9.5
11
10 [0.394]
9
8.5
4
6.5
3
11.5
13
16 [0.630]
12.5
9
6
9.5
4
16
19
3
6
W
6.5
Y
Z
12 16
16 17
7.5 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Single Acting Pull Type (mm)
● Flange A mount BTAL
Bore size × Stroke -3A
BTAL- Bore size
MULTI-3A
φV
Piston rod diameter
0.8
N
M5×0.8
φ6
φ10, φ16
A＋
（Stroke×2）
T
B＋Stroke
T
10
I
C＋Stroke
E
I
1
G
G
U
H
XZ
BC
BH
BH
XZ
BC
O
10
J
2-φAP
AF
BG
BG
K
YZ
2-φAP
AF
φL
6
● Flange B mount BTAL
11＋W
BB＋Stroke
YZ
4-M3×0.5 (Both sides)
Bore size × Stroke -3B
BTAL- Bore size
MULTI-3B
φV
N
0.8
Piston rod diameter
M5×0.8
φ6
φ10, φ16
（Stroke×2）
A＋
T
2-φAP
2-φAP
C＋Stroke
B＋Stroke
T
E
I
I
1
G
U
G
H
O
S
BI
XZ
XZ
S
BI
J
YZ
YZ
BF
BE
Type
Code
K
11＋W
φL
6
BF
BB＋Stroke
BE
4-M3×0.5 (Both sides)
Standard cylinder Cylinder with magnet
A
E
G
H
I
Bore
mm [in.]
6 [0.236]
48 33 53 38 15 7.5
5
7
5.5 1.8 M3×0.5
10 [0.394] 53 35 58 40 18 10.5 6
10
7
2.4 M4×0.7
16 [0.630] 58 38 63 43 20 12.5 7
12
8
3.2 M5×0.8 10 –0
–0.05 12.5 19 33 20
C
A
C
B
J
K
L
N
O
S
T
6 –0
–0.05 10 14 20 12
U
V
3
8 –0
–0.05 11.5 15 24 14 10.5 5
6
W AF AP BB BC BE BF BG BH BI XZ YZ
6.5
6
8
3.5
20 27.5 24 18
24 31.5 26 20
3.5
14
16
7.5 12 4.5 27 42 36 28 4.5 21
5
6
9.5 11
11.5 13
16 19
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Double Acting Double Rod Type (mm)
● Side mount BDADL
Bore size × Stroke
BDAL- Bore size
N
φV
Piston rod diameter
N
1.6
D＋Stroke
2-M5×0.8
φ10, φ16
φ10, φ16
（Stroke× 2）
A＋
B
T
F＋Stroke
C＋Stroke
1
E
I
U
G
11
G
1
R
H
Q
Y
XZ
CD
S
O
CE
J
φCP
CF
CG
4-M3×0.5 (Both sides)
6
K
W
φL
2-P
Z
M＋Stroke
YZ
X＋Stroke
φ6
T
φ6
10
I
Q
XZ
CD
S
10
CE
R
φCP
CF CG
YZ
Type
Code
Bore
mm [in.]
Standard cylinder
Cylinder with magnet
A
A
C
D
M
X
C
D
M
B
X
E
F
G
6 [0.236] 53 28 8 12 27 58 33 13 17 32 15 7.5 10 5
H
I
J
K
L
N
O
P
Q
R
S
T
7 5.5 1.8 M3×0.5 6 –0
–0.05 10 14 φ3.5 Counterboreφ6 Depth4.2 (Both sides) 15 7 20 12
U
V W Y
3
10 [0.394] 61 30 7 13 31 66 35 12 18 36 18 10.5 13 6 10 7 2.4 M4×0.7 8 –0
–0.05 11.5 15 φ3.5 Counterboreφ6 Depth3.2 (Both sides) 18 8 24 14 10.5 5
16 [0.630] 68 33 8 15 35 73 38 13 20 40 20 12.5 15 7 12 8 3.2 M5×0.8 10 –0
–0.05 12.5 19 φ4.5 Counterboreφ7.6 Depth4.2 (Both sides) 25 12 33 20
Code
Bore
mm [in.]
CD
CE
CF
CG
CP
XZ
YZ
6 [0.236]
7.5
7.5
3.5
5.5
2.5
9.5
11
10 [0.394]
9
8.5
4
6.5
3
11.5
13
16 [0.630]
12.5
9
6
9.5
4
16
19
6.5
Z
12 16
16 17
6 7.5 24 18
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
Dimensions of Non-rotating Double Acting Double Rod Type (mm)
● Flange A mount BDADL
Bore size × Stroke -3A
BDADL- Bore size
MULTI-3A
N
D＋Stroke
φV
Piston rod diameter
1.6
N
2-M5×0.8
φ6
φ10, φ16
A＋（Stroke×2）
T
B
T
10
I
F＋Stroke
C＋Stroke
E
I
1
G
U
G
1
H
XZ
BC
BH
BH
XZ
BC
O
10
J
φL
2-φAP
AF
BG
BG
K
YZ
● Flange B mount BDADL
11＋W
4-M3×0.5 (Both sides)
6
2-φAP
AF
BB
YZ
Bore size × Stroke -3B
BDADL- Bore size
MULTI-3B
N
N
D＋Stroke
1.6
φV
Piston rod diameter
2-M5×0.8
φ6
φ10, φ16
A＋（Stroke×2）
B
T
T
2-φAP
2-φAP
I
F＋Stroke
C＋Stroke
E
I
1
G
G
U
1
H
O
S
BI
XZ
XZ
S
BI
J
YZ
YZ
BF
BE
Type
K
φL
BB
BE
Standard cylinder Cylinder with magnet
E
I
J
K
A
C
D
A
F
G
H
Bore
mm [in.]
6 [0.236]
53 28
8
58 33 13 15 7.5 10
5
7 5.5 1.8 M3×0.5
10 [0.394] 61 30
7
66 35 12 18 10.5 13
6
10
7 2.4 M4×0.7
16 [0.630] 68 33
8
73 38 13 20 12.5 15
7
12
8 3.2 M5×0.8 10 –0
–0.05 12.5 19 33 20
Code
11＋W
4-M3×0.5 (Both sides)
6
BF
C
D
B
L
N
O
S
T
6 –0
–0.05 10 14 20 12
U
V
3
8 –0
–0.05 11.5 15 24 14 10.5 5
W AF AP BB BC BE BF BG BH BI XY YZ
6.5
6
8
3.5
20 27.5 24 18
24 31.5 26 20
3.5
14
16
6 7.5 12 4.5 27 42 36 28 4.5 21
5
6
9.5 11
11.5 13
16 19
Note: The 4-M3 × 0.5 female thread (for sensor switch mounting) in the drawing should not be used for mounting the cylinder. Moreover, it is not available in the
cylinder body of a standard 5mm [0.197in.] stroke cylinder.
MOUNTING BRACKETS
Rod Side Mounting Bracket,
Head Side Mounting Bracket
Mounting Bracket Model (Order Codes)
Head side
Rod side
Mounting
location
●How to read the codes
Bor
Mounting
es
ize
brackets
mm
[in.
]
Cylinder model
Side mount
Foot A mount
6 [0.236]
DB60A
DB61A
DB63A
DB63B
10 [0.394]
D100A
D101A
D103A
D103B
16 [0.630]
D160A
D161A
D163A
D163B
6 [0.236]
LB60A
−
LB63A
LB63B
10 [0.394]
L100A
−
L103A
L103B
16 [0.630]
L160A
−
L163A
L163B
6 [0.236]
BB60A
BB61A
BB63A
BB63B
All types except
10 [0.394]
double rod type
16 [0.630]
B100A
B101A
B103A
B103B
B160A
B161A
B163A
B163B
BDA□
BSA□
BTA□
BDAD□
BDAL□
BSAL□
BTAL□
BDADL□
Flange A mount Flange B mount
Mount type
0A
Side mount
1A
Foot A mount
3A
Flange A mount
3B
Flange B mount
Bore size
B6
φ6 [0.236in.]
10
φ10 [0.394in.]
16
φ16 [0.630in.]
Applicable cylinder
D — BDA □, BSA □, BTA □, and BDAD □
(for rod side)
L — BDAL □, BSAL □, BTAL □, and
BDADL □ (for rod side)
B — All types except double rod type
(for head side)
Remarks: 1. All mounting brackets come with 2 mounting screws.
2. Order separately for all head side mounting brackets.
3. For the order codes of rod side mounting brackets assembled with cylinders, see p.99 and 115.
4. No rod side foot A mount for the non-rotating cylinder is available. For non-rotating double rod cylinders, however,
a separately ordered foot A mount can be installed on the rod side opposite the non-rotation plate.
5. A rod bushing is assembled into the rod side mounting bracket.
Dimensions of Head Side Mounting Bracket (mm)
Flange A mount: -3A
MULTI-1A
●φ6
T
●φ6
T
10
G
R
BH
BC
10
R
BG
G
AG
T
G
φBJ
AC
10
Q
BH
φBJ
BE
10
Q
R
BH
AF
AI
AF
●φ10,16
2-φAP
●φ10,16
●φ10,16
BE
T
T
G
R
BH
2-φAP
BF
2-φAP
AD
G
MULTI-3B
φBJ
G
Q
●φ6
Flange B mount: -3B
MULTI-3A
S
Foot A mount: -1A
R
R
BH
AG
AF
AI
AF
Code
G
Q
S
Q
BF
2-φAP
2-φAP
AD
Bore
size mm [in.]
φBJ
BC
Q
G
BG
AC
φBJ
Q
φBJ
BH
T
G
R
S
T
AC
AD
AF
2-φAP
AG
AI
AP
BC
BE
BF
BG
BH
BJ
2 +0.05
0
2 +0.05
0
2 +0.05
0
8 +0.1
0
6 [0.236]
5
15
7
20
12
26
13
6
9
4
3.5
27.5
24
18
3.5
10 [0.394]
6
18
8
24
14
31
14
8
10
4
3.5
31.5
26
20
3.5
16 [0.630]
7
25
12
33
20
41.5
17
12
12
5
4.5
42
36
28
4.5
Remark: For the side mount (head cover), see the cylinder dimensions.
12 +0.1
0
18 +0.1
0
SENSOR SWITCHES
Solid State Type, Reed Switch Type
Order Codes (for Sensor Switches Only)
Sensor switches
Solid state type
DC10〜28V
with indicator lamp
Solid state type
DC4.5〜28V
with indicator lamp
Option
Lead wire length
With sensor holder
ZC130
ZC153
Reed switch type DC5〜28V
without indicator lamp AC85〜115V
CS5T
Reed switch type
DC10〜28V
with indicator lamp
CS11T
A
B
-BDAS6
-BDAS10
-BDAS16
Moving Sensor Switch
● Loosening mounting screw allows the sensor switch to be
moved freely in the cylinder’s axial direction.
● Tighten the mounting screw with a tightening torque of
19.6N·cm [1.73in·lbf] or less.
●φ6
Mounting screw
Sensor switch
Sensor holder
●A :1000mm [39in.]
●B :3000mm [118in.]
★ Order codes of sensor holders only
Forφ6 cylinder — C1-BDAS6
●-BDAS6 : For φ 6 cylinder
Forφ10 cylinder — C1-BDAS10
●-BDAS10 : For φ 10 cylinder
Forφ16 cylinder — C1-BDAS16
●-BDAS16 : For φ 16 cylinder
● For sensor switch details, see p.1544.
●φ10,16
Mounting screw
Sensor switch
Sensor holder
Minimum Cylinder Strokes When Using
Sensor Switches
mm [in.]
Bore size
Solid state type sensor switch Reed switch type sensor switch
Mounting 2 pcs. Mounting 1 pc. Mounting 2 pcs. Mounting 1 pc.
6 [0.236]
10 [0.394]
5
5
10
5
16 [0.630]
Remark: Two sensor switches cannot be mounted on a cylinder with flange
B mount.
Mount 1 sensor switch on the head side when the flange B mount
is used on the rod side, and mount 1 sensor switch on the rod side
when the flange B mount is used on the head side.
Sensor Switch Operating Range, Response Differential, and Maximum Sensing Location
● Operating range: R
The distance the piston travels in one direction, while the
switch is in the ON position.
● Response differential: C
The distance between the point where the piston turns the
switch ON, and the point where the switch is turned OFF as
the piston travels in the opposite direction.
mm [in.]
Bore size
Sensor switch
Magnet
R
CS5T□,CS11T□
ZC130□,ZC153□
Operating range Response differential Operating range Response differential
6 [0.236]
2.0〜3.0
[0.079〜0.118]
0.3 [0.012]
or less
4.8〜7.2
[0.189〜0.283]
1.3 [0.051]
or less
10 [0.394]
2.0〜3.0
[0.079〜0.118]
0.3 [0.012]
or less
5.8〜8.3
[0.228〜0.327]
2.0 [0.079]
or less
16 [0.630]
2.5〜4.0
[0.098〜0.157]
0.3 [0.012]
or less
7.5〜9.4
[0.295〜0.370]
2.5 [0.098]
or less
C (Response differential)
ON
OFF
R
ON
OFF
C (Response differential)
Maximum sensing location
Remark: The above table shows reference values.
Mounting Location of End of Stroke Detection Sensor Switch
●Cylinder with magnet
●Double rod cylinder with magnet
Connection port
Y
●Non-rotating cylinder with magnet
●Non-rotating double rod cylinder
X
Sensor switch model marking
7.5
Y
X
■Double acting type (Including double rod cylinders)
Bore size
7.5
mm [in.]
Sensor switch model
Mounting
location ZC130□, ZC153□
CS11T□
Bore size
Mounting
location
mm [in.]
Sensor switch model
ZC130□,ZC153□
CS5T□
CS11T□
6 [0.236]
X
13.0 [0.512]
11.5 [0.453]
15 [0.591]
6 [0.236]
X
6.0 [0.236]
4.5 [0.177]
8 [0.315]
10 [0.394]
Y
8.0 [0.315]
6.5 [0.256]
10 [0.394]
10 [0.394]
Y
1.0 [0.039]
−0.5 [−0.020]
3 [0.118]
X
14.0 [0.551]
12.5 [0.492]
16 [0.630]
X
7.0 [0.276]
5.5 [0.217]
9 [0.354]
Y
9.0 [0.354]
7.5 [0.295]
11 [0.433]
Y
2.0 [0.079]
0.5 [0.020]
4 [0.157]
16 [0.630]
CS5T□
■Double acting type (Including double rod cylinders)
■Single acting push type
mm [in.]
16 [0.630]
■Single acting push type
mm [in.]
Sensor switch model
Mounting
Bore size
location ZC130□, ZC153□
CS5T□
CS11T□
Sensor switch model
Mounting
Bore size
location ZC130□, ZC153□
CS5T□
6 [0.236]
X
8.0 [0.315]
6.5 [0.256]
10 [0.394]
6 [0.236]
X
1.0 [0.039]
−0.5 [−0.020]
3 [0.118]
10 [0.394]
Y
8.0 [0.315]
6.5 [0.256]
10 [0.394]
10 [0.394]
Y
1.0 [0.039]
−0.5 [−0.020]
3 [0.118]
X
9.0 [0.354]
7.5 [0.295]
11 [0.433]
X
2.0 [0.079]
0.5 [0.020]
4 [0.157]
Y
9.0 [0.354]
7.5 [0.295]
11 [0.433]
Y
2.0 [0.079]
0.5 [0.020]
4 [0.157]
16 [0.630]
■Single acting pull type
mm [in.]
Sensor switch model
Mounting
Bore size
location ZC130□, ZC153□
CS5T□
6 [0.236]
X
13.0 [0.512]
11.5 [0.453]
10 [0.394]
Y
13.0 [0.512]
X
Y
16 [0.630]
16 [0.630]
■Single acting pull type
CS11T□
mm [in.]
CS11T□
Sensor switch model
Mounting
Bore size
location ZC130□, ZC153□
CS5T□
CS11T□
15 [0.591]
6 [0.236]
X
6.0 [0.236]
11.5 [0.453]
8 [0.315]
11.5 [0.453]
15 [0.591]
10 [0.394]
Y
6.0 [0.236]
11.5 [0.453]
8 [0.315]
14.0 [0.551]
12.5 [0.492]
16 [0.630]
X
7.0 [0.276]
12.5 [0.492]
9 [0.354]
14.0 [0.551]
12.5 [0.492]
16 [0.630]
Y
7.0 [0.276]
12.5 [0.492]
9 [0.354]
16 [0.630]
Remarks: 1. The above tables give reference values for the standard strokes. For the procedure to find-out the best position, see p.129.
2. The above figures show the piping connection port when it has been turned to face upward.
3. Use the distance between the cylinder mounting hole and the rod cover to confirm the mounting location of the double rod cylinder’s end of stroke
detection sensor switch.
4. Mount the sensor switch so that the surface showing the sensor switch model marking faces up.
Dimensions of Sensor Switch Mounting (mm)
●φ6
MULTI-SW
●φ10
20
7.5
7.5
5.5
4.5
1
5.5
33
35
1
10.5
24
26
10
12.5
12.5
14.5
1
20
1
22
1
10
14
6.5
1
12
●φ16
15.5
17.5
Precautions for Mounting Cylinders with Magnet
When mounting 2 or more Multi Mount
Cylinders with sensor switches in close
proximity, use the conditions shown to
the right.
With shield plate
Without shield plate
R
R
R
Bore size
mm [in.]
Shield plate
Shield plate
6 [0.236]
25mm [0.984] or longer
23mm [0.906] or longer
22mm [0.866] or longer
10 [0.394]
29mm [1.142] or longer
31mm [1.220] or longer
25mm [0.984] or longer
16 [0.630]
35mm [1.378] or longer
39mm [1.535] or longer
31mm [1.220] or longer
Remark: Aside from the above, there are no particular restrictions on mounting.
Shield Plate Type (Order Codes)
R
Ope
Applicable shield plate type
ratio
Str
oke n type
Double acting type, Double acting double rod type Single acting push/pull type
m
Bore
m
5, 10, 15
20, 25, 30
5, 10
15
size mm [in.]
6 [0.236]
BS061
BS062
BS061
BS062
10 [0.394]
BS101
BS102
BS101
BS102
16 [0.630]
BS161
BS162
BS161
BS162
Remarks: 1. All shield plates come with 2 mounting screws.
2. Order all shield plates separately.
MULTI-SE
">