Koganei G010 - Solenoid valve G010 series Instruction manual

BK-UV002 Ver.1.0
Air Valve
SOLENOID VALVES G010 SERIES
INSTRUCTION MANUAL Ver.1.0
Handling Instructions and Precautions
Piping Precautions
Use the piping shown below for the manifold, as well.
2-, 3-port valves valve functions and connection port configurations
Positive pressure specifications
Normally
open
（NO）
2(A)
2(A)
De-energized
1(P)
3(R) (plug)
2-port
Normally
closed
（NC）
Vacuum specifications
Energized
1(P) (plug)
3(R)
Normally
closed
（NC）
2(A)
Normally
open
（NO）
2(A)
1(P)
3(R)
3-port
3-port
2-port
De-energized
1(P)
3(R)
Normally
closed
（NC）
2(A)
Normally
open
（NO）
2(A)
Normally
closed
（NC）
2(A)
Normally
open
（NO）
2(A)
Energized
1(P) (vacuum pump, etc.)
3(R) (plug)
1(P) (plug)
3(R) (vacuum pump, etc.)
1(P) (vacuum pump, etc.)
(atmospheric air and
3(R)
positive pressure)
(atmospheric air and
positive pressure)
3(R) (vacuum pump, etc.)
1(P)
Caution: Normally closed (NC) and normally open (NO) valves cannot be mounted together on the same manifold.
About the 2-, 3-port valves
The G010 series can be divided, by the types of gaskets used
on the valves, into 3-port and 2-port valves.
When replacing the valve, pay attention to the gasket shape
and mounting direction.
G□010□E1 (For 3-port)
G□010□E1-2 (For NC, 2-port)
G□010□E1-2-11 (For NO, 2-port)
3(R) 2(A) 1(P)
No hole in the 3(R) port section.
Gasket has holes in three places.
No hole in the 1(P) port section.
Solenoid
Manual override
Plug connector
Locking type
Internal circuit
＜Standard type, low current type＞
●DC5V, DC6V, DC12V, DC24V
Solenoid with LED indicator (Surge suppression)
●Positive common
LED indicator
（Light Emitting Diode）
Lead wire: Red（＋）
（COM）
Lead wire: Black（−）
LED indicator: Red
●Negative common (Made to order)
Attaching and removing plug connector
To lock the manual override, use a small
screwdriver to push down on the manual
override all the way and turn it clockwise.
When locked, turning the manual override in
the counterclockwise direction releases a
spring on the manual override, returns it to the
original position, and releases the lock.
When the manual override is not turned, this
type acts just like the non-locking type, the
valve is energized as long as the manual
override is pushed down, and it returns to the
rest position upon release.
Use fingers to insert the connector into the
pin, push it in until the lever claw latches
onto the protruded section of the connector
housing, and complete the connection.
To remove the connector, squeeze the lever
along with the connector, lift the lever claw
up from the protruded section of the
connector housing, and pull it out.
Connector housing
Protruded section
Pin
LED indicator
（Light Emitting Diode）
Lever
Lead wire: Red（＋）
RN
TU
（COM）
Plug connector
Lead wire: Black（−）
Indication of polarity（DC）
LED indicator: Red
Contact
●AC100V, AC200V
Solenoid with LED indicator (Surge suppression)
H
US
P
−
Lead wire（AC）
Yellow: AC100V
White: AC200V
C
＋
Indication of polarity（DC）
（COM）
Crimping of connecting lead wire and contact
Lead wire（AC）
Yellow: AC100V
White: AC200V
＜Large flow type＞
●DC12V, DC24V
Solenoid with LED indicator (Surge suppression)
●Positive common
Lead wire: Red（＋）
Cautions: 1. Always release the lock of the locking
type before commencing normal
operation.
2. Do not attempt to operate the manual
override with a pin or other object
having an extremely fine tip. It could
damage the manual override button.
To crimp lead wires into contacts, strip off
4mm [0.16in.] of the insulation from the end
of the lead wire, insert it into the contact,
and crimp it. Be sure to avoid catching the
insulation on the exposed wire crimping
section.
Insulation crimp tab
Exposed wire
crimping section
Exposed wire 4mm
Solenoid
ia
Timer
circuit
（COM）
Contact
Hook
is
Insulation
（Maximum outer diameter:φ1.5）
Lead wire: Black（−）
Lead wire
Applied wire
AWG＃24〜＃30
LED indicator: Red
●Negative common (Made to order)
Attaching and removing contact and connector
Lead wire: Red（＋）
Solenoid
（COM）
ia
Timer
circuit
is
Lead wire: Black （−）
LED indicator: Red
ia: Starting current
is: Steady-state current
Operating principles of large flow type
The large flow type uses a timer circuit, as
shown above, that achieves power savings
by switching to holding operations mode
after a certain period of time to operate at
about 1/3 of the starting power consumption.
●Power waveform
Solenoid
valves
Power
consumption
ON
OFF
3.2W
Reduced
power consumption
1.1W
Start-up time
Start-up time (Standard time)
DC12V
48ms
DC24V
27ms
Cautions: 1. Do not apply megger between the
lead wires.
2. The DC solenoid will not short circuit
even if the wrong polarity is applied,
but the valve will not operate.
3. Leakage current inside the circuit
could result in failure of the solenoid
valve to return, or in other erratic
operation. Always use it within the
range of the allowable leakage
current. If circuit conditions, etc. cause
the current leakage to exceed the
maximum allowable leakage current,
consult us.
4. The large flow type will not operate if
the supply voltage is increased slowly.
Always apply the appropriate voltage.
Insert the contact with lead wire into a plug
connector □ hole until the contact hook
latches on the connector and is secured to
the plug connector. Confirm that the lead
wire cannot be easily pulled out.
To remove it, insert a tool with a fine tip
(such as a small screwdriver) into the
rectangular hole on the side of the plug
connector to push up on the hook, and then
pull out the lead wire.
Cautions: 1. Do not pull hard on the lead wire. It
could result in defective contacts,
shorted lines, etc.
2. If the pin is bent, use a small
screwdriver, etc. to gently
straighten out the pin, and then
complete the connection to the plug
connector.
3. For crimping of connecting lead
wire and contact, always use a
dedicated crimping tool.
Contact: Model 706312-2MK
Manufactured by Sumiko Tech, Inc.
Crimping tool: Model F1
(for 706312-2MK)
Manufactured by Sumiko Tech, Inc.
Handling Instructions and Precautions
Lead wire for common wiring
(only lead wire)
Common pre-wired lead wire assembly
Using the lead wire for common wiring, provided as
additional parts, saves wiring work.
Using the common pre-wired lead wire assembly, provided as
additional parts, saves wiring work.
Order code
Order code
CR1652W −
G010-COM
Common specifications
Blank
Positive common
M
Negative common
Lead wire length
Blank
300mm [11.8in.]
1
1000mm [39in.]
3
3000mm [118in.]
1. Wiring example of DC positive side
and AC common terminal
（−） （−） （−） （−） （−） （−）
COM（＋）
Outlet position of common wiring
S
The type PS is stn.1 side, the type PL is final stn. side.
E
The type PS is final stn. side, the type PL is stn.1 side.
Lead wire for
common wiring
Number of wiring units
2：2 units
〜
20：20 units
Connector
Connector housing
Common pre-wired lead wire assembly
Shows polarity in DC case
2. Wiring example of DC negative side
common terminal
1. For CR1652W–6E□
2. For CR1652W–6E□M
（＋） （＋） （＋） （＋） （＋） （＋）
（−） （−） （−） （−） （−） （−）
COM（＋）
COM（−）
（＋） （＋） （＋） （＋） （＋） （＋）
COM（−）
Lead wire for
common wiring
Lead wire assembly
for common wiring
Lead wire assembly
for common wiring
Connector
Connector
Connector
Connector housing
3. For CR1652W–6S□
4. For CR1652W–6S□M
（−）（−） （−） （−） （−） （−）
Cautions: 1. The diagrams show the straight
connector configuration.
2. Since the COM terminal is connected
to a crossover terminal inside the
connector housing, the connector
cannot be switched between a positive
common and a negative common
wiring by changing the connectors.
（＋） （＋） （＋） （＋） （＋） （＋）
COM（＋）
COM（−）
Lead wire assembly
for common wiring
Lead wire assembly
for common wiring
Connector
Connector
Caution: Since the COM terminal is connected to a crossover terminal inside
the connector housing, the connector
cannot be switched between a
positive common and a negative
common wiring by changing the
connectors.
Number of valves which can be energized
simultaneously with common wiring
DC5,6V
E1
6
G010
LE1
12
HE1
−
DC12V
12
20
4
DC24V
20
20
8
AC100V
20
−
−
AC200V
20
−
−
Model
Voltage
Fittings
Recommended fittings
G
（V）
010□E1‐21
Connection port
2(A) port
1(P), 3(R) port
TS4-M3M
TS3-M3M
TSH4-M3M
TSH3-M3M
TL4-M3M
TL3-M3M
─
For urethane tube
BF4BU-M3
BF3BU-M3
BF4BU-M3
BF3BU-M3
For nylon tube
BF4-M3
BF4-M3
2(A) port
1(P), 3(R) port
TS4-M5M
TSH4-M5M
TL4-M5M
TLL4-M5M
TS4-M5M
TSH4-M5M
TL4-M5M
TLL4-M5M
For urethane tube
BF4BU
BF3BU
BF4BU
BF3BU
For nylon tube
BF4
BF4
Fitting
Quick fitting
TAC fitting
GA
（V）
010□E1‐25
Connection port
Fitting
Quick fitting
TAC fitting
SOLENOID VALVES
SERIES
Specifications
Basic Models and Functions
G010E1(-11)
GV010E1(-11)
(standard)
Item
For A type manifold Note2
For direct piping, F type manifold Note1
Basic model
G010LE1(-11)
GV010LE1(-11)
(low current)
GA010E1(-11)
GAV010E1(-11)
(standard)
G010HE1(-11)
GV010HE1(-11)
(large flow)
Number of positions
GA010LE1(-11)
GAV010LE1(-11)
(low current)
GA010HE1(-11)
GAV010HE1(-11)
(large flow)
2 positions
Number of ports
2, 3 ports
Valve function
Normally closed (NC, standard) or normally open (NO, option)
Remark: For optional specifications and order code, see p. 45〜46.
Notes: 1. When using the G010□E1, GV010□E1 as a single unit, select it with a mounting base.
2. When using the GA010□E1, GAV010□E1 as a single unit, select it with a sub-base.
Specifications (Positive Pressure)
Direct piping, F type manifold
Basic model
G010E1
(standard)
Item
G010LE1
(low current)
A type manifold
G010HE1
(large flow)
GA010E1
(standard)
Direct acting type
Operation type
Note 1
Effective area〔Cv〕
mm2
1
（P）
→2
（A）
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
2
（A）
→3
（R）
0.3〔0.017〕
0.2〔0.011〕
0.6〔0.033〕
0.3〔0.017〕
0.2〔0.011〕
0.6〔0.033〕
M3×0.5
Port size Note 2
M5×0.8
Not required
Lubrication
Operating pressure range
0〜0.7 {0〜7.1} [0〜102]
MPa {kgf/cm 2} [psi.]
1.05 {10.7} [152]
MPa {kgf/cm 2} [psi.]
Response time Note3 ON/OFF
ms
Maximum operating frequency
Hz
5/10
4/8
3/6
Shock resistance
DC12V,DC24V
AC100V,
（AC200V）
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
（DC5V,DC6V）
DC12V,DC24V
AC100V,
（AC200V）
Direct piping, F type manifold
Basic model
G010E1-11
(standard)
Item
G010LE1-11
(low current)
DC24V
GA010E1-11
(standard)
GA010LE1-11
(low current)
GA010HE1-11
(large flow)
Air
Direct acting type
Operation type
（A）
→1
（P）
Note 1 2
Effective area〔Cv〕
mm2 3
（R）
→2
（A）
0.3〔0.017〕
0.15〔0.008〕
0.55〔0.031〕
0.3〔0.017〕
0.15〔0.008〕
0.55〔0.031〕
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
M3×0.5
Port size Note 2
M5×0.8
Not required
Lubrication
Operating pressure range
MPa {kgf/cm 2} [psi.]
0〜0.7 {0〜7.1} [0〜102]
0〜0.5 {0〜5.1} [0〜73]
Response time Note 3 ON/OFF
ms
Hz
0〜0.7 {0〜7.1} [0〜102]
0〜0.5 {0〜5.1} [0〜73]
1.05 {10.7} [152]
MPa {kgf/cm 2} [psi.]
Maximum operating frequency
4/8
5/10
3/6
4/8
5/10
3/6
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
5
5〜50 [41〜122]
Operating temp. range (atmosphere and media) °C [°F] Note4
1373.0 {140.0} (Axial direction 196.2 {20.0})
m/s2 {G}
（DC5V,DC6V）
DC12V,DC24V
AC100V,
（AC200V）
Air supply port
（DC12V）
DC12V,DC24V
A type manifold
G010HE1-11
(large flow)
Media
Mounting direction
（DC5V,DC6V）
Any
Mounting direction
Rated voltage Note 5
3/6
5〜50 [41〜122]
（DC5V,DC6V）
Shock resistance
5/10
1373.0 {140.0} (Axial direction 196.2 {20.0})
m/s2 {G}
Rated voltage Note 5
4/8
5
Operating temp. range (atmosphere and media) °C [°F] Note4
Proof pressure
GA010HE1
(large flow)
Air
Media
Proof pressure
GA010LE1
(low current)
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
（DC5V,DC6V）
DC12V,DC24V
AC100V,
（AC200V）
Any
3(R) port
Notes: 1. For details, see the effective area on p.43.
2. For details, see the port size on p.43.
3. Values when air pressure is 0.5MPa {5.1kgf/cm2} [73psi.]. Due to switching phase timing, add a maximum of 5ms to the AC response time.
4. Provide heat radiation measures to ensure that the ambient temperature (or when used in a control box, the internal temperature of the box) always
remains within the temperature range specifications.
And for long-time continuous energizing, consult us.
5. Values in parentheses ( ) are for made to order items. See the corresponding table of solenoid options/voltage on p.50.
Specifications (Vacuum)
Basic model
Direct piping, F type manifold
GV010E1
(standard)
Item
GV010LE1
(low current)
A type manifold
GV010HE1
(large flow)
GAV010E1
(standard)
GAV010LE1
(low current)
GAV010HE1
(large flow)
Air
Media
Direct acting type
Operation type
Note 1
Effective area〔Cv〕
mm2
1
（P）
→2
（A）
0.3〔0.017〕
0.15〔0.008〕
0.55〔0.031〕
0.3〔0.017〕
0.15〔0.008〕
0.55〔0.031〕
2
（A）
→3
（R）
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
M3×0.5
Port sizeNote 2
M5×0.8
Not required
Lubrication
Operating pressure range
MPa {kgf/cm2} [psi.]
Proof pressure
−100kPa〜0 {−750.1mmHg〜0} [−29.53in.Hg〜0]
1(P) port
3(R) port
0〜0.5 {0〜5.1} [0〜73]
0〜0.4 {0〜4.1} [0〜58]
Response time Note 3 ON/OFF
ms
Maximum operating frequency
Hz
5/10
4/8
3/6
4/8
5/10
3/6
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
5〜50 [41〜122]
1373.0 {140.0} (Axial direction 196.2 {20.0})
m/s2 {G}
（DC5V,DC6V）
DC12V,DC24V
Rated voltage Note 5
0〜0.4 {0〜4.1} [0〜58]
5
Operating temp. range (atmosphere and media) °C [°F] Note4
Shock resistance
0〜0.5 {0〜5.1} [0〜73]
1.05 {10.7} [152]
MPa {kgf/cm 2} [psi.]
AC100V,
（AC200V）
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
（DC5V,DC6V）
DC12V,DC24V
AC100V,
（AC200V）
Mounting direction
Any
Air supply port
Vacuum
1(P) port
Positive pressure
3(R) port
Basic model
Direct piping, F type manifold
GV010E1-11
(standard)
Item
GV010LE1-11
(low current)
A type manifold
GV010HE1-11
(large flow)
GAV010E1-11
(standard)
GAV010LE1-11
(low current)
GAV010HE1-11
(large flow)
Air
Media
Direct acting type
Operation type
Note 1
Effective area〔Cv〕
mm2
2
（A）
→1
（P）
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
0.2〔0.011〕
0.1〔0.006〕
0.45〔0.025〕
3
（R）
→2
（A）
0.3〔0.017〕
0.2〔0.011〕
0.6〔0.033〕
0.3〔0.017〕
0.2〔0.011〕
0.6〔0.033〕
M3×0.5
Port sizeNote 2
M5×0.8
Not required
Lubrication
Operating pressure range
MPa {kgf/cm2} [psi.]
Proof pressure
1(P) port
0〜0.5 {0〜5.1} [0〜73]
0〜0.4 {0〜4.1} [0〜58]
ms
Maximum operating frequency
Hz
5/10
4/8
3/6
5/10
3/6
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
5〜50 [41〜122]
1373.0 {140.0} (Axial direction 196.2 {20.0})
m/s2 {G}
（DC5V,DC6V）
DC12V,DC24V
Rated voltage Note 5
4/8
5
Operating temp. range (atmosphere and media) °C [°F] Note4
AC100V,
（AC200V）
（DC5V,DC6V）
（DC12V）
DC12V,DC24V
DC24V
Mounting direction
Air supply port
0〜0.4 {0〜4.1} [0〜58]
1.05 {10.7} [152]
MPa {kgf/cm 2} [psi.]
Response time Note 3 ON/OFF
Shock resistance
0〜0.5 {0〜5.1} [0〜73]
−100kPa〜0 {−750.1mmHg〜0} [−29.53in.Hg〜0]
3(R) port
（DC5V,DC6V）
DC12V,DC24V
AC100V,
（AC200V）
Any
Vacuum
3(R) port
Positive pressure
1(P) port
Notes: 1. For details, see the effective area on p.43.
2. For details, see the port size on p.43.
3 Values when air pressure is 0.5MPa {5.1kgf/cm2} [73psi.]. Due to the switching phase timing, add a maximum of 5ms to the AC
response time.
4. Provide heat radiation measures to ensure that the ambient temperature (or when used in a control box, the internal temperature
of the box) always remains within the temperature range specifications.
And for long-time continuous energizing, consult us.
5. Values in parentheses ( ) are for made to order items. See the corresponding table of solenoid options/voltage on p.50.
Mass
Solenoid Valve Mass
g [oz.]
Manifold Mass
g [oz.]
Basic model
Mass
Manifold model
Mass calculation of each unit (n=number of units)
Block-off plate
G（V）010E1
14.6 [0.515] (16.8 [0.593])Note1
G010M□F
(7×n) ＋9 [(0.247×n) ＋0.317]
1 [0.035]
G（V）010LE1
14.6 [0.515] (16.8 [0.593])Note1
G010M□A
(7×n) ＋9 [(0.247×n) ＋0.317]
1 [0.035]
G（V）010HE1
15.3 [0.540] (17.5 [0.617])Note1
G010MH□F
(7.2×n) ＋33 [(0.254×n) ＋1.164]
1 [0.035]
GA（V）010E1
14.2 [0.501] (26.2 [0.924])Note2
G010MH□A
(7.2×n) ＋33 [(0.254×n) ＋1.164]
1 [0.035]
GA（V）010LE1
14.2 [0.501] (26.2 [0.924])Note2
GA（V）010HE1
14.8 [0.522] (26.8 [0.945])Note2
Notes: 1. Figures in parentheses ( ) are the mass with mounting base: -21.
2. Figures in parentheses ( ) are the mass with sub-base: -25.
Solenoid Specifications
Rated voltage
DC5V
DC6V
DC12V
DC24V
4.5〜5.5
(5±10%)
5.4〜6.6
(6±10%)
10.8〜13.2
(12±10%)
21.6〜26.4
(24±10%)
200
168
84
42
Item
V
G(A)(V)010LE1 G(A)(V)010E1
Operating voltage range
Current (when rated voltage is applied) mA(r.m.s)
1.0W
Power consumption
21
Starting mA
267
133
Holding mA
92
100
84
11
8
1.1VA
1.6VA
0.5W
Power consumption
Current (when rated
voltage is applied)
1.0
mA
Allowable leakage current
G(A)(V)010HE1
180〜220
(200±10%)
1.0
42
Current (when rated voltage is applied) mA(r.m.s)
AC200V Note
90〜110
(100±10%)
2.0
mA
Allowable leakage current
AC100V Note
46
Starting W
Power consumption
3.2
Holding W
1.1
Allowable leakage current
mA
10
5
Start-up time (standard time)
ms
48
27
Over 100
MΩ
Insulation resistance
Grommet type: 300mm [11.8in.], Plug connector type: 300mm [11.8in.]
Wiring type and lead wire length
Red (＋), Black (−)
Color of lead wire
Yellow
White
Red
Color of LED indicator
Flywheel diode
Surge suppression (as standard)
Bridge diode
Note: Since the AC types have built-in bridge diodes, the starting current value and energizing current value are virtually the same. In addition, the rated
frequencies are 50Hz and 60Hz. Specification values are the same for both.
Effective Area〔Cv〕
mm 2
Standard (Single valve)
Basic model
Remarks
G010E1（-11）
（
1 P）
→2
（A）0.2
〔0.011〕
（
2 A）
→3
（R）0.3
〔0.017〕
（
2 A）
→1
（P）0.3
〔0.017〕
（
3 R）
→2
（A）0.2
〔0.011〕
G010LE1（-11）
2 A）
→1
（P）0.15〔0.008〕
（
1 P）
→2
（A）0.1〔0.006〕 （
3 R）
→2
（A）0.1〔0.006〕
（
2 A）
→3
（R）0.2〔0.011〕 （
G010HE1（-11）
（
1 P）
→2
（A）0.45〔0.025〕 （
2 A）
→1
（P）0.55〔0.031〕
（
2 A）
→3
（R）0.6〔0.033〕 （
3 R）
→2
（A）0.45〔0.025〕
GV010E1（-11）
2 A）
→1
（P）0.2〔0.011〕
（
1 P）
→2
（A）0.3〔0.017〕 （
3 R）
→2
（A）0.3〔0.017〕
（
2 A）
→3
（R）0.2〔0.011〕 （
GV010LE1（-11）
2 A）
→1
（P）0.1〔0.006〕
（
1 P）
→2
（A）0.15〔0.008〕 （
3 R）
→2
（A）0.2〔0.011〕
（
2 A）
→3
（R）0.1〔0.006〕 （
GV010HE1（-11）
2 A）
→1
（P）0.45〔0.025〕
（
1 P）
→2
（A）0.55〔0.031〕 （
3 R）
→2
（A）0.6〔0.033〕
（
2 A）
→3
（R）0.45〔0.025〕 （
GA010E1（-11）
2 A）
→1
（P）0.3〔0.017〕
（
1 P）
→2
（A）0.2〔0.011〕 （
3 R）
→2
（A）0.2〔0.011〕
（
2 A）
→3
（R）0.3〔0.017〕 （
GA010LE1（-11）
（
1 P）
→2
（A）0.1〔0.006〕 （
2 A）
→1
（P）0.15〔0.008〕
（
2 A）
→3
（R）0.2〔0.011〕 （
3 R）
→2
（A）0.1〔0.006〕
GA010HE1（-11）
（
1 P）
→2
（A）0.45〔0.025〕 （
2 A）
→1
（P）0.55〔0.031〕
（
2 A）
→3
（R）0.6〔0.033〕 （
3 R）
→2
（A）0.45〔0.025〕
GAV010E1（-11）
（
1 P）
→2
（A）0.3〔0.017〕 （
2 A）
→1
（P）0.2〔0.011〕
（
2 A）
→3
（R）0.2〔0.011〕 （
3 R）
→2
（A）0.3〔0.017〕
GAV010LE1（-11）
（
1 P）
→2
（A）0.15〔0.008〕 （
2 A）
→1
（P）0.1〔0.006〕
（
2 A）
→3
（R）0.1〔0.006〕 （
3 R）
→2
（A）0.2〔0.011〕
GAV010HE1（-11）
（
1 P）
→2
（A）0.55〔0.031〕 （
2 A）
→1
（P）0.45〔0.025〕
（
2 A）
→3
（R）0.45〔0.025〕 （
3 R）
→2
（A）0.6〔0.033〕
● For the case with quick fitting TSH4M3M attached to the 1(P) and 2(A)
ports on the mounting base.
● Same values as for the case with
quick fitting TSH4-M3M attached to
the 2(A) port on F type manifold.
● For the case with quick fitting TSH4M5M attached to the 1(P) and 2(A)
ports on the mounting sub-base.
Remark: Figures in parentheses ( ) are for the normally open (NO) type.
Port Size
Solenoid Valve Port Size (With Base)
Basic model
G（V）010E1- 21
G（V）010LE1- 21
G（V）010HE1- 21
GA（V）010E1- 25
GA（V）010LE1- 25
GA（V）010HE1- 25
Port
（
1 P）
,3
（R）
（
2 A）
Location of piping ports
Mounting base
Valve
Port size
M3×0.5
Manifold Port Size
Manifold model
G010M□F
M3×0.5
G010M□A
1（P）,2（A）,3（R）
Sub-base
M5×0.8
G010MH□F
G010MH□A
Port
Location of piping ports
Port size
（
1 P）
,3
（R）
Manifold
M5×0.8
（
2 A）
Valve
M3×0.5
M5×0.8
（
1 P）
,3
（R）
（
2 A）
Manifold
M3×0.5
（
1 P）
,3
（R）
Manifold
Rc1/8
（
2 A）
Valve
M3×0.5
（
1 P）
,3
（R）
（
2 A）
Manifold
Rc1/8
M5×0.8
Flow Rate
1（P）→2（A）
〔3（R）→2（A）〕
0.5
0.4
0.3
0.3
0.2
0.1
0
0.2
0.1
G010E1〔-11〕
GA010E1〔-11〕
0.5
0.4
0.3
0.3
0.2
0.2
0.1
0.1
0
2 4 6 8 10121416182022242628
0.5
0.4
G010LE1〔-11〕
GA010LE1〔-11〕
2
4
Supply pressure
0.6
0.5
0.4
0.3
0.2
0.2
0.1
0.1
0
G010E1〔-11〕
GA010E1〔-11〕
Valve outlet pressure
Valve outlet pressure
0.7
0.3
0.3
0.2
0.2
0.1
0.1
2
G010LE1-11
GA010LE1-11
4
Supply pressure
0.5
0.6
0.4
0.5
0.4
0.3
0
2 4 6 8 10121416182022242628
0.7
0.2
0.1
0.1
2
4
Flow rate R/min
（ANR）
G010LE1
GA010LE1
6
0.6
0.4
0.5
0.4
0.3
0.3
0.2
0.2
0.1
0.1
0
8 10 12 14 16 18
Flow rate R/min
（ANR）
0.5
0.5
0.4
0.4
0.3
0.2
0.1
0.3
0.2
0.1
G010HE1〔-11〕
GA010HE1〔-11〕
MPa
0.6
0.5
0.4
0.5
0.4
0.3
0.3
0.2
0.1
0
5 10 15 20 25 30 35 40 45 50 55
Flow rate R/min
（ANR）
Supply pressure
MPa 0.7
MPa
0.6
0
8 10 12 14 16 18
0.7
0.6
G010HE1
GA010HE1
5 10 15 20 25 30 35 40 45 50 55
2（A）→1（P）
Supply pressure
MPa 0.7
MPa
0.2
0.7
0.5
Flow rate R/min
（ANR）
0.6
0.3
6
MPa
0.6
1（P）→2（A）
〔3（R）→2（A）〕
MPa 0.7
MPa
0.4
0.4
0.3
2（A）→3（R）
0.6
0.5
0.6
0.5
0.4
0
8 10 12 14 16 18
0.7
0.5
Flow rate R/min
（ANR）
Flow rate R/min
（ANR）
2（A）→3（R）
〔2（A）→1（P）〕
MPa 0.7
6
MPa
0.6
Supply pressure
MPa 0.7
Valve outlet pressure
0.6
0.4
0.6
Valve outlet pressure
0.5
Valve outlet pressure
Valve outlet pressure
0.7
0.6
Supply pressure
MPa 0.7
MPa
0.7
MPa
0.6
2（A）→3（R）
2（A）→1（P）
Supply pressure
MPa 0.7
Valve outlet pressure
Supply pressure
Valve outlet pressure
1（P）→2（A）
〔3（R）→2（A）〕
MPa 0.7
0.2
0.1
G010HE1-11
GA010HE1-11
5 10 15 20 25 30 35 40 45 50 55
Flow rate R/min
（ANR）
Flow rate R/min
（ANR）
Note: 0.6MPa [73psi.] and 0.7MPa [102psi.] are not
available for G010HE1-11, GA010HE1-11.
1MPa = 145psi., 1R/min = 0.0353ft.3/min.
How to read the graph (for G□010E1, 1(P)→2(A))
When the supply pressure is 0.5MPa [73psi.] and flow rate is 10R/min [0.35ft.3/min.]
(ANR), the valve outlet pressure becomes 0.39MPa [57psi.].
Figures in brackets〔 〕indicate the normally open (NO) type.
Air Supply Time and Exhaust Time
How to read the graph
Exhaust time:
Time required for chamber interior to convert from atmospheric
pressure state to vacuum state.
Air supply time: Time required for chamber interior to convert from –100kPa
[–29.53in.Hg] to atmospheric pressure state.
Measurement conditions
Digital
memory
scope
Pressure sensor
q
Primary tank
(13.6R
[0.480ft.3])
w
q and w are quick fittings.
TSH4-M5M
Chamber
GAV010E1-25
0.25R[0.0088ft.3]
GAV010E1-11-25
GAV010LE1-25
0.5R [0.0177ft.3]
GAV010LE1-11-25
1.0R [0.0353ft.3]
GAV010HE1-25
GAV010HE1-11-25
GAV010E1 Air supply time
GAV010E1-11 Exhaust time
GAV010E1-11 Air supply time
kPa −101.3
kPa −101.3
kPa −101.3
kPa −101.3
−76.0
−76.0
GAV010E1
Exhaust time
−50.7
500cc
250cc
−50.7
−25.3
−25.3
250cc
−50.7
500cc
1
2
3
4
Time
500cc
−50.7
250cc
−25.3
−25.3
1000cc
1000cc
0
Vacuum
250cc
1000cc
−76.0
−76.0
500cc
Vacuum
Vacuum
Vacuum
1000cc
0
5
1
2
3
4
Time
s
0
5
0
1
2
s
3
4
Time
5
1
2
3
4
Time
s
GAV010LE1 Exhaust time
GAV010LE1 Air supply time
GAV010LE1-11 Exhaust time
GAV010LE1-11 Air supply time
kPa −101.3
kPa −101.3
kPa −101.3
kPa −101.3
−76.0
−76.0
−76.0
−76.0
250cc
−50.7
250cc
−25.3
1
2
3
−50.7
250cc
−25.3
−25.3
1000cc
1000cc
0
500cc
500cc
500cc
−25.3
−50.7
Vacuum
250cc
1000cc
500cc
Vacuum
−50.7
Vacuum
Vacuum
1000cc
4
Time
0
5
1
2
3
4
Time
s
0
5
1
2
s
3
4
Time
0
5
1
2
3
4
Time
s
GAV010HE1 Exhaust time
GAV010HE1 Air supply time
GAV010HE1-11 Exhaust time
GAV010HE1-11 Air supply time
kPa −101.3
kPa −101.3
kPa −101.3
−76.0
−76.0
1000cc
−50.7
500cc
−25.3
−25.3
−76.0
500cc
−50.7
Vacuum
−50.7
1000cc
Vacuum
Vacuum
Vacuum
250cc
250cc
500cc
1000cc
−25.3
1000cc
−50.7
500cc
−25.3
250cc
250cc
0
1
2
3
Time
–100kPa = –29.53in.Hg,
5
s
kPa −101.3
−76.0
5
s
4
5
0
1
3
Time
s
250cc = 0.0088ft.3,
2
500cc = 0.0177ft.3,
4
5
s
1000cc = 0.0353ft.3
0
1
2
3
Time
4
5
s
0
1
2
3
Time
4
5
s
G010 Series Solenoid Valve Order Codes
■ 2-, 3-port valve
■ 2-, 3-port valve
Number of ports
■ Mounting base
3-port
Blank
2（A）
Normally closed
(NC)
1（P）
3（R）
■ Wiring type
Without mounting
base
Without sub-base
● Lead wire length:
300mm [11.8in.] is standard.
Grommet type with
LED indicator
Blank
Blank
-11
Normally open
(NO)
Blank
Note: For the piping,
see table on
p.37.
2-port
2（A）
■ Sub-base
Valve function
With mounting
base
Blank
Straight connector
with LED indicator
With sub-base
1（P）
-2
-21
-25
● Attached to a
valve body at
shipping.
●Attached to a
valve body at
shipping.
-PS
L connector with
LED indicator
Positive pressure
-PL
Positive pressure
Vacuum
Direct piping
Vacuum
Sub-base piping
Basic model
Voltage
2-, 3-port
standard type
G010E1
DC12V, DC24V, AC100V
2-, 3-port
low current type
G010LE1
DC12V, DC24V
2-, 3-port
large flow type
G010HE1
2-, 3-port
standard type
GV010E1
2-, 3-port
low current type
GV010LE1
DC12V, DC24V
2-, 3-port
large flow type
GV010HE1
DC24V
2-, 3-port
standard type
GA010E1
DC12V, DC24V, AC100V
2-, 3-port
low current type
GA010LE1
DC12V, DC24V
2-, 3-port
large flow type
GA010HE1
2-, 3-port
standard type
GAV010E1
2-, 3-port
low current type
GAV010LE1
DC12V, DC24V
2-, 3-port
large flow type
GAV010HE1
DC24V
-11 Note 2
-2
-11 Note 2
-2
-PS
-PL
-21 Note 1
-PS
-PL
-25 Note 1
DC24V
DC12V, DC24V, AC100V
DC24V
DC12V, DC24V, AC100V
Notes: 1. If using the solenoid valve as a single unit, always select it either with mounting base or with sub-base.
2. Normally closed (NC) and normally open (NO) valves cannot be mounted togther on the same manifold.
Made to Order (After the wiring order code, enter the codes below.)
Straight connector
with LED indicator
Negative common
L connector with
LED indicator
Negative common
Lead wire length
Voltage specifications
●G□010E1：DC5V, DC6V, AC200V
●G□010LE1：DC5V, DC6V
-1L
-3L
-MS
Straight connector
with LED indicator
Without connector, contact
and lead wire
Negative common
-MSX
-ML
Straight connector
with LED indicator
Without connector, contact
and lead wire
Positive common
-PSX
●G□010HE1：DC12V
● For plug connector
● Length -1L: 1000 [39in.]
(mm) -3L: 3000 [118in.]
● For AC110V〜120V, AC220V〜240V
specifications, consult us.
L connector with
LED indicator
Without connector, contact
and lead wire
Negative common
L connector with
LED indicator
Without connector, contact
and lead wire
Positive common
Straight connector
with LED indicator
Connector,
contact included.
Without lead wire.
Negative common
-MLX
-PLX
-MSN
Straight connector
with LED indicator
Connector,
contact included.
Without lead wire.
Positive common
-PSN
L connector with
LED indicator
Connector,
contact included.
Without lead wire.
Negative common
L connector with
LED indicator
Connector,
contact included.
Without lead wire.
Positive common
-MLN
-PLN
G010 Series Manifold Order Codes
■ 2-, 3-port valve
■ 2-, 3-port valve
■ Wiring type
Number of ports
Valve function
● Lead wire length:
300mm [11.8in.] is standard.
3-port
Blank
Grommet type
2（A）
1（P）
Normally closed
（NC）
3（R）
Blank
-11
Normally open
（NO）
2-port
-PS
Blank
L connector with
LED indicator
Note: For the piping,
see table on
p.37.
2（A）
Straight connector
with LED indicator
1（P）
-2
Manifold model
Number of units
Station
P, R port (M5×0.8) type
F
G010M
stn.□
⁝
2
⁝
20
stn.□
A
P, R port (Rc1/8) type
F
G010MH
stn.□
⁝
2
⁝
20
stn.□
A
●Valve mounting location from the left-hand side when
facing the 2(A) port (□: 1〜20)
Additional Parts (To be ordered separately)
Mounting base
G010-21
● For direct piping
(With gasket)
Mounting base
G010H-21
● For direct piping.
For G010HE1-11,
GV010HE1 only
(With gasket).
Sub-base
G010-25
● For sub-base
piping
(With gasket)
-PL
Basic model
Voltage
-G010E1
DC12V, DC24V, AC100V
-G010LE1
DC12V, DC24V
-G010HE1
DC24V
-GV010E1
DC12V, DC24V, AC100V
-GV010LE1
DC12V, DC24V
-GV010HE1
-GA010E1
-2
-11
-PS
-PL
DC24V
DC12V, DC24V, AC100V
-GA010LE1
DC12V, DC24V
-GA010HE1
DC24V
-GAV010E1
DC12V, DC24V, AC100V
-GAV010LE1
DC12V, DC24V
-GAV010HE1
DC24V
-G010E1
DC12V, DC24V, AC100V
-G010LE1
DC12V, DC24V
-G010HE1
DC24V
-GV010E1
DC12V, DC24V, AC100V
-GV010LE1
DC12V, DC24V
-GV010HE1
-2
-11
-GA010E1
-PS
-PL
DC24V
DC12V, DC24V, AC100V
-GA010LE1
DC12V, DC24V
-GA010HE1
DC24V
-GAV010E1
DC12V, DC24V, AC100V
-GAV010LE1
DC12V, DC24V
-GAV010HE1
DC24V
●Specify the valve type for each station.
●Enter -BP when closing a station with a block-off plate without mounting a valve.
●Normally closed (NC) and normally open (NO) valves cannot be mounted together
on the same manifold.
Lead wire for common
wiring
Common pre-wired lead
wire assembly
G010-COM
CR1652W- □
● For -PS, -PL, -MS,
-ML
(Set of 10 pcs.）
● For details, see
p.39.
Block-off plate
G010-BP
Operating Principles and Symbols
3-port
Normally
closed (NC)
Spring holder
Solenoid
Manual override
Poppet
Flapper spring
（
2 A）
Sealed cap
（
1 P）
（
3 R）
Column
Major Parts and Materials
Normally
open (NO)
Materials
Parts
Body
（
2 A）
（
3 R）
（
1 P）
（
3 R）
Body
（
1 P）
Valve
Plunger spring
Overspring
Plunger
Base
Poppet
Manifold
Plastic
Poppet
Synthetic rubber
Plunger
Column
Magnetic stainless
steel
Base
Aluminum alloy（anodized）
Body
Aluminum alloy（anodized）
Block-off plate
Plastic
Seal
Synthetic rubber
Corresponding Table of Mounting Valve/Manifold
Base piping
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
G010MH□A
G010MH□F
G010M□A
●
●
●
●
●
●
●
●
●
●
●
●
-25
Standard
Small flow
Large flow
Standard
Small flow
Large flow
Standard
Small flow
Large flow
Standard
Small flow
Large flow
Applicable manifolds
(Sub-base)
1.0W
0.5W
3.2W（1.1W）Note2
1.0W
0.5W
3.2W（1.1W）Note2
1.0W
0.5W
3.2W（1.1W）Note2
1.0W
0.5W
3.2W（1.1W）Note2
-21
G010E1
G010LE1
G010HE1
GV010E1
GV010LE1
GV010HE1
GA010E1
GA010LE1
GA010HE1
GAV010E1
GAV010LE1
GAV010HE1
(Mounting base)
Flow rate
-11 Note 1
Power
(Normally open, NO)
Basic model
-2
Direct piping
(2-port)
Piping
configuration
Valve options
G010M□F
Valve specifications
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
2(A) port
（M3） M3 （M3） M5
1(P), 3(R) port
M5 M5 Rc1/8 Rc1/8
●: Selectable or mountable
Notes: 1. Care should be taken when ordering, since the initial settings for the normally closed (NC) and normally open
(NO) valves cannot be changed later on.
Normally closed (NC) and normally open (NO) valves cannot be mounted together on the same manifold.
2. Values in parentheses ( ) in power column are for holding state.
Dimensions of Direct Piping Solenoid Valve (mm)
G010E1
7
G010E1(-11)-21
(DC5V, DC6V, DC12V, DC24, AC100V)
G010LE1(-11)-21
G010HE1-21
GV010E1(-11)-21
GV010LE1(-11)-21 2-φ2.2 thru hole
4
GV010HE1-11-21
（300）
（25.6）
6
LED indicator
19.6
10
32
1
8.5
10.25
7
15
2-M3×0.5
(Connection port)
G010HE1-11-21
GV010HE1-21
3.9
（18.7）
6
6
18
（
1 P）
（
3 R）
（33）
Manual
override
Mounting base (-21)
M3×0.5
(2(A) port)
17.6
7
(DC24V)
4
2-φ2.2 thru hole
（25.6）
6
（300）
LED indicator
19.6
10
34
（20.7）
15
7
17.6
M3×0.5
(2(A) port)
G010E1̲ 2
7
2-φ2.2 thru hole
4
（25.6）
6
LED indicator
（300）
10
19.6
Manual
override
2-M3×0.5
(Connection port)
7
M3×0.5
(2(A) port)
1
15
17.6
10.25
8.5
（17）
18
6
（
3 R）
6
（
1 P）
3.9
37
Mounting base (-21)
（38）
G010E1(-11)-21 (AC200V)
GV010E1(-11)-21
1
2-M3×0.5
(Connection port)
12.25
10.5
5.9
6
H
8
3（R）
20
1（P）
（35）
Manual
override
Mounting base (-21)
Dimensions of Sub-base Piping Solenoid Valve (mm)
GA010E1
GA010E1(-11)-25
(DC5V, DC6V, DC12V, DC24V, AC100V)
GA010LE1(-11)-25
GA010HE1-25
GAV010E1(-11)-25
GAV010LE1(-11)-25
GAV010HE1-11-25
LED indicator
10
2-M5×0.8
(Connection
port)
2-φ3.4 thru hole
(Mounting hole)
4
5.5
10
8
（3）
17
20
Sub-base (-25)
(DC24V)
（300）
LED indicator
19.6
10
2-M5×0.8
(Connection
port)
2-φ3.4 thru hole
(Mounting hole)
17
20
GA010E12
(AC200V)
（300）
LED indicator
10
2-M5×0.8
(Connection
port)
2-φ3.4 thru hole
(Mounting hole)
Manual
override
8
（3）
17
20
13
5.5
7
15
Sub-base (-25)
10.25
8.5
4
（17）
9.5
20
（
2 A）
11.5
12
37
M5×0.8
(Connection port)
4
19.6
（
3 R）
（33.6）
5.5
13
（
3 R）
10
8
（3）
Sub-base (-25)
14
（
1 P）
34
10.5
5.5
7
15
GA010E1(-11)-25
GAV010E1(-11)-25
12.25
12
H
（
1 P）
2
11.5
5.5
Manual
override
4
9.5
20
（
2 A）
（20.7）
M5×0.8
(Connection port)
4
（33.6）
14
（
3 R）
7
15
GA010HE1-11-25
GAV010HE1-25
（
1 P）
32
8.5
12
（18.7）
9.5
20
（
2 A）
11.5
5.5
Manual
override
10.25
M5×0.8
(Connection port)
13
（300）
19.6
4
（33.6）
14
10
Dimensions of Connector (mm)
Options
G010E1PL
●Solenoid with straight
connector (AC200V): -PS
●Solenoid with L connector
(AC200V): -PL
●Solenoid with straight
connector: -PS
G010E1L2
G010E1PS
G010E1P2
19.6
14
19.6
Made to order connectors are the
same dimensions in the drawings.
R
R
14
（30.2）
R
（30.2）
19.6
Code
Model
（48.1）
(Overall length of valve)
（16.5）
(To the bottom of the valve)
37 (Overall length of valve)
32
(To the bottom of the valve)
（43.1）
(Overall length of valve)
（16.8）
(To the bottom of the valve)
32 (Overall length of valve)
19.6
37
R
(To the bottom of the valve)
●Solenoid with L
connector: -PL
R
Blank
300
- 1L
1000
- 3L
3000
Corresponding Table of Solenoid Options/Voltage
Connector specifications
-PS
-PL
-MS
-ML
-PSX
-PLX
-MSX
-MLX
-PSN
-PLN
-MSN
-MLN
G(A)010LE1〔-11〕
G(A)V010LE1〔-11〕
(low current type)
(grommet)
G(A)010E1〔-11〕
G(A)V010E1〔-11〕
(standard type)
Voltage
specifications
DC5V
△
△
△
△
△
△
△
△
△
△
△
△
△
DC6V
△
△
△
△
△
△
△
△
△
△
△
△
△
DC12V
●
●
●
△
△
△
△
△
△
△
△
△
△
DC24V
●
●
●
△
△
△
△
△
△
△
△
△
△
AC100V
●
●
●
△
△
△
△
AC200V
△
△
△
△
△
△
△
DC5V
△
△
△
△
△
△
△
△
△
△
△
△
△
DC6V
△
△
△
△
△
△
△
△
△
△
△
△
△
DC12V
●
●
●
△
△
△
△
△
△
△
△
△
△
Blank
Basic valve models
DC24V
●
●
●
△
△
△
△
△
△
△
△
△
△
G(A)010HE1〔-11〕
G(A)V010HE1〔-11〕
(large flow type)
DC12V
△
△
△
△
△
△
△
△
△
△
△
△
△
DC24V
●
●
●
△
△
△
△
△
△
△
△
△
△
Lead wire length options
same for all basic models
-1L
△
△
△
△
△
△
△
△
△
△
△
△
-3L
△
△
△
△
△
△
△
△
△
△
△
△
●: Standard specifications △: Made to order
Dimensions of F Type Manifold (for Direct Piping with Positive Pressure Solenoid Valves) (mm)
G010MF
G010M□F (1(P), 3(R) port: M5×0.8)
G010E1
For the piping, see the table on p.37.
2‐φ3.2
(Mounting hole)
G010LE1-PS
G010HE1-PL
LED indicator
3
−
3.5
4.5
9
C
＋
Ｌ
（
3 R） （
1 Ｐ）
43.6
32.5
15.3
8.2
Block-off plate
(-BP)
（
1 Ｐ） （
3 R）
20
Manual override
H
P
4‐M5×0.8
(Both sides)
With 2 plugs
（3.5）
L
M3×0.5 (2(A) port)
Stn.1
Unit dimensions
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
Stn.3
Stn.4
10.2 (Pitch)
14
Number of units
12
13
14
15
16
17
18
19
20
―
44.2
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
Stn.2
12
33.6
Number of units
2
3
4
5
6
7
8
9
10
11
mm
G010M□F (1(P), 3(R) port: M5×0.8)
G010LE1-11
2‐φ3.2
(Mounting hole)
G010E1-11-PS
G010HE1-11-PL
4‐M5×0.8
(Both sides)
3
−
Ｌ
C
＋
（
3 R） （
1 Ｐ）
32.5
45.1 (For HE1)
43.6 (For E1, LE1)
Block-off plate
(-BP)
（1.5）
15.3
8.2
4.5
9
Manual override
（
1 Ｐ） （
3 R）
20
LED indicator
H
3.5
P
（3.5）
L
M3×0.5 (A port)
Stn.1
Unit dimensions
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
14
Number of units
12
13
14
15
16
17
18
19
20
―
33.6
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
12
44.2
Number of units
2
3
4
5
6
7
8
9
10
11
mm
For optional wiring, see p.50.
Stn.2
With 2 plugs
Stn.3
Stn.4
10.2 (Pitch)
Dimensions of F Type Manifold (for Direct Piping with Vacuum Solenoid Valves) (mm)
G010M□F (1(P), 3(R) port: M5×0.8)
GV010LE1
For the piping, see the table on p.37.
2‐φ3.2
(Mounting hole)
GV010E1-PS
GV010HE1-PL
3
−
4‐M5×0.8
(Both sides)
Ｌ
C
＋
（
3 R） （
1 Ｐ）
32.5
45.1 (For HE1)
43.6 (For E1, LE1)
Block-off plate
(-BP)
（1.5）
15.3
8.2
4.5
9
Manual override
（
1 Ｐ） （
3 R）
20
LED indicator
H
3.5
P
With 2 plugs
（3.5）
L
M3×0.5 (2(A) port)
Stn.1
Unit dimensions
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
Stn.4
33.6
Number of units
12
13
14
15
16
17
18
19
20
―
Stn.3
10.2 (Pitch)
14
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
Stn.2
12
44.2
Number of units
2
3
4
5
6
7
8
9
10
11
mm
G010MF
G010M□F (1(P), 3(R) port: M5×0.8)
GV010E1-11
GV010E1-11-PS
2‐φ3.2
(Mounting hole)
GV010E1-11-PL
LED indicator
3
−
3.5
4.5
9
C
＋
（
3 R） （
1 Ｐ）
32.5
15.3
8.2
Block-off plate
(-BP)
（
1 Ｐ） （
3 R）
20
43.6
Manual override
P
4‐M5×0.8
(Both sides)
（3.5）
L
M3×0.5 (2(A) port)
Stn.1
Unit dimensions
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
33.6
Number of units
12
13
14
15
16
17
18
19
20
―
14
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
12
44.2
Number of units
2
3
4
5
6
7
8
9
10
11
mm
For optional wiring, see p.50.
Stn.2
With 2 plugs
Stn.3
Stn.4
10.2 (Pitch)
Dimensions of F Type Manifold (for Direct Piping with Positive Pressure Solenoid Valves) (mm)
G010MHF
G010MH□F (1(P), 3(R) port: Rc1/8)
G010E1
For the piping, see the table on p.37.
G010LE1-PS
2‐φ3.2
(Mounting hole)
G010HE1-PL
LED indicator
（
3 R）
15.8
With 2 plugs
（8.5）
M3×0.5 (2(A) port)
Stn.3
Stn.2
Stn.1
Stn.4
10.2 (Pitch)
17
15.2
34.8
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
45.4
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
H
P
mm
Number of units
12
13
14
15
16
17
18
19
20
―
（
1 Ｐ）
36.8
8.5
29
23
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
＋
L
4‐Rc1/8
(Both sides)
Unit dimensions
C
（
3 R）
9.2
−
Ｌ
8.5
7.2
Number of units
2
3
4
5
6
7
8
9
10
11
（
1 Ｐ）
47.9
Manual override
Block-off plate
(-BP)
G010MH□F (1(P), 3(R) port: Rc1/8)
G010HE1-11
G010HE1-11-PS
2‐φ3.2
(Mounting hole)
G010HE1-11-PL
LED indicator
（
3 R）
15.8
（
1 Ｐ）
36.8
8.5
45.4
34.8
15.2
29
23
For optional wiring, see p.50.
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
17
Stn.2
With 2 plugs
（8.5）
P
Stn.1
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
＋
M3×0.5 (2(A) port)
mm
Number of units
12
13
14
15
16
17
18
19
20
―
C
H
L
4‐Rc1/8
(Both sides)
Unit dimensions
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
H
（
3 R）
9.2
−
H
8.5
7.2
Number of units
2
3
4
5
6
7
8
9
10
11
（
1 Ｐ）
47.9
Manual override
Block-off plate
(-BP)
Stn.3
Stn.4
10.2 (Pitch)
Dimensions of F type Manifold (for Direct Piping with Vacuum Solenoid Valves) (mm)
G010MHF
G010MH□F (1(P), 3(R) port: Rc1/8)
GV010HE1
For the piping, see the table on p.37.
GV010HE1-PS
2‐φ3.2
(Mounting hole)
GV010HE1-PL
LED indicator
（
3 R）
15.8
（
1 Ｐ）
36.8
8.5
29
23
With 2 plugs
（8.5）
M3×0.5 (2(A) port)
Stn.4
10.2 (Pitch)
15.2
34.8
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
Stn.3
Stn.2
Stn.1
17
45.4
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
＋
P
mm
Number of units
12
13
14
15
16
17
18
19
20
―
C
H
L
4‐Rc1/8
(Both sides)
Unit dimensions
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
H
（
3 R）
9.2
−
H
8.5
7.2
Number of units
2
3
4
5
6
7
8
9
10
11
（
1 Ｐ）
47.9
Manual override
Block-off plate
(-BP)
G010MH□F (1(P), 3(R) port: Rc1/8)
GV010HE1-11
GV010HE1-11-PS
2‐φ3.2
(Mounting hole)
GV010HE1-11-PL
LED indicator
（
3 R）
15.8
15.2
34.8
45.4
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
17
For optional wiring, see p.50.
Stn.2
With 2 plugs
（8.5）
P
Stn.1
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
H
M3×0.5 (2(A) port)
mm
Number of units
12
13
14
15
16
17
18
19
20
―
（
1 Ｐ）
36.8
8.5
29
23
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
＋
L
4‐Rc1/8
(Both sides)
Unit dimensions
C
H
（
3 R）
9.2
−
H
8.5
7.2
Number of units
2
3
4
5
6
7
8
9
10
11
（
1 Ｐ）
47.9
Manual override
Block-off plate
(-BP)
Stn.3
Stn.4
10.2 (Pitch)
Dimensions of A Type Manifold (for Manifold Piping with Positive Pressure Solenoid Valves) (mm)
G010MA
G010M□A (1(P), 3(R) port: M5×0.8)
GA010E1
For the piping, see the table on p.37.
2‐φ3.2
(Mounting hole)
GA010LE1-PS
GA010HE1-PL
LED indicator
3
−
3.5
4.5
9
Stn. 1
Stn. 2
With 2 plugs
（3.5）
Stn. 3
Stn. 4
（
2 A）
5
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
14
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
33.6
mm
Number of units
12
13
14
15
16
17
18
19
20
―
44.2
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
H
10.2 (Pitch)
12
Number of units
2
3
4
5
6
7
8
9
10
11
＋
P
L
4‐M5×0.8
(Both sides)
Unit dimensions
C
Ｌ
（
3 R） （
1 Ｐ）
32.5
8.2
15.3
Block-off plate
(-BP)
（
1 Ｐ） （
3 R）
20
43.6
Manual override
M3×0.5 (Connection port)
G010M□A (1(P), 3(R) port: M5×0.8)
GA010LE1-11
2‐φ3.2
(Mounting hole)
GA010E1-11-PS
GA010HE1-11-PL
43.6 (For E1, LE1)
（1.5）
4‐M5×0.8
(Both sides)
3
Block-off plate
(-BP)
−
Ｌ
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
（
2 A）
5
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
33.6
mm
Number of units
12
13
14
15
16
17
18
19
20
―
14
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
M3×0.5 (Connection port)
For optional wiring, see p.50.
Stn. 2
With 2 plugs
（3.5）
P
L
Stn. 1
44.2
Number of units
2
3
4
5
6
7
8
9
10
11
＋
H
3.5
12
Unit dimensions
C
（
3 R） （
1 Ｐ）
32.5
45.1 (For HE1)
8.2
15.3
4.5
9
Manual override
（
1 Ｐ） （
3 R）
20
LED indicator
Stn. 3
Stn. 4
10.2 (Pitch)
Dimensions of A Type Manifold (for Manifold Piping with Vacuum Solenoid Valves) (mm)
G010MA
G010M□A (1(P), 3(R) port: M5×0.8)
GAV010LE1
For the piping, see the table on p.37.
2‐φ3.2
(Mounting hole)
GAV010E1-PS
GAV010HE1-PL
43.6 (For E1, LE1)
（1.5）
4‐M5×0.8
(Both sides)
3
Block-off plate
(-BP)
−
Ｌ
3.5
Stn. 2
Stn. 3
Stn. 4
10.2 (Pitch)
mm
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
（
2 A）
5
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
14
Number of units
12
13
14
15
16
17
18
19
20
―
33.6
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
With 2 plugs
（3.5）
P
L
Stn. 1
44.2
Number of units
2
3
4
5
6
7
8
9
10
11
＋
H
12
Unit dimensions
C
（
3 R） （
1 Ｐ）
32.5
45.1 (For HE1)
8.2
15.3
4.5
9
Manual override
（
1 Ｐ） （
3 R）
20
LED indicator
M3×0.5 (Connection port)
G010M□A (1(P), 3(R) port: M5×0.8)
GAV010E1-11
2‐φ3.2
(Mounting hole)
GAV010E1-11-PS
GAV010E1-11-PL
LED indicator
3
−
3.5
4.5
9
Stn. 1
12
mm
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
（
2 A）
5
L
136.2
146.4
156.6
166.8
177
187.2
197.4
207.6
217.8
―
14
Number of units
12
13
14
15
16
17
18
19
20
―
33.6
P
L
34.2 27.2
44.4 37.4
54.6 47.6
64.8 57.8
68
75
85.2 78.2
95.4 88.4
105.6 98.6
115.8 108.8
119
126
44.2
Number of units
2
3
4
5
6
7
8
9
10
11
M3×0.5 (Connection port)
For optional wiring, see p.50.
＋
Stn. 2
With 2 plugs
（3.5）
P
L
4‐M5×0.8
(Both sides)
Unit dimensions
C
（
3 R） （
1 Ｐ）
32.5
8.2
15.3
Block-off plate
(-BP)
（
1 Ｐ） （
3 R）
20
43.6
Manual override
Stn. 3
Stn. 4
10.2 (Pitch)
Dimensions of A Type Manifold (for Manifold Piping with Positive Pressure Solenoid Valves) (mm)
G010MHA
G010MH□A (1(P), 3(R) port: Rc1/8)
GA010E1
For the piping, see the table on p.37.
2‐φ3.2
(Mounting hole)
GA010LE1-PS
GA010HE1-PL
（
3 R）
Stn. 1
mm
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
（8.5）
Stn. 2
Stn. 3
Stn. 4
10.2 (Pitch)
17
（
2 A）
5
15.2
Number of units
12
13
14
15
16
17
18
19
20
―
With 2 plugs
L
45.4
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
H
34.8
Number of units
2
3
4
5
6
7
8
9
10
11
＋
P
4‐Rc1/8
(Both sides)
Unit dimensions
C
（
1 Ｐ）
36.8
15.8
23
8.5
7.2
9.2
−
Ｌ
（
3 R）
8.5
29
Manual override
Block-off plate
(-BP)
（
1 Ｐ）
47.9
LED indicator
M5×0.8 (Connection port)
G010MH□A (1(P), 3(R) port: Rc1/8)
GA010HE1-11
2‐φ3.2
(Mounting hole)
GA010HE1-11-PS
GA010HE1-11-PL
15.8
（
3 R）
P
Stn. 1
mm
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
（
2 A）
5
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
15.2
Number of units
12
13
14
15
16
17
18
19
20
―
34.8
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
17
45.4
Number of units
2
3
4
5
6
7
8
9
10
11
For optional wiring, see p.50.
＋
H
M5×0.8 (Connection port)
Stn. 2
With 2 plugs
（8.5）
Ｌ
4‐Rc1/8
(Both sides)
Unit dimensions
C
（
1 Ｐ）
36.8
8.5
H
8.5
7.2
9.2
−
H
（
3 R）
23
29
Manual override
Block-off plate
(-BP)
（
1 Ｐ）
47.9
LED indicator
Stn. 3
Stn. 4
10.2 (Pitch)
Dimensions of A Type Manifold (for Manifold Piping with Vacuum Solenoid Valves) (mm)
G010MHA
G010MH□A (1(P), 3(R) port: Rc1/8)
GAV010HE1
For the piping, see the table on p.37.
2‐φ3.2
(Mounting hole)
GAV010HE1-PS
GAV010HE1-PL
15.8
（
3 R）
P
Stn. 1
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
Stn. 2
Stn. 3
Stn. 4
（
2 A）
5
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
（8.5）
34.8
Number of units
12
13
14
15
16
17
18
19
20
―
With 2 plugs
10.2 (Pitch)
17
15.2
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
mm
45.4
Number of units
2
3
4
5
6
7
8
9
10
11
＋
H
Ｌ
4‐Rc1/8
(Both sides)
Unit dimensions
C
（
1 Ｐ）
36.8
8.5
H
8.5
7.2
9.2
−
H
（
3 R）
23
29
Manual override
Block-off plate
(-BP)
（
1 Ｐ）
47.9
LED indicator
M5×0.8 (Connection port)
G010MH□A (1(P), 3(R) port: Rc1/8)
GAV010HE1-11
2‐φ3.2
(Mounting hole)
GAV010HE1-11-PS
GAV010HE1-11-PL
（
2 A）
5
P
129.2
139.4
149.6
159.8
170
180.2
190.4
200.6
210.8
―
15.2
L
146.2
156.4
166.6
176.8
187
197.2
207.4
217.6
227.8
―
34.8
mm
Number of units
12
13
14
15
16
17
18
19
20
―
For optional wiring, see p.50.
H
（
3 R）
15.8
17
45.4
P
L
44.2 27.2
54.4 37.4
64.6 47.6
74.8 57.8
68
85
95.2 78.2
105.4 88.4
115.6 98.6
125.8 108.8
119
136
＋
P
Stn. 1
Number of units
2
3
4
5
6
7
8
9
10
11
C
M5×0.8 (Connection port)
Stn. 2
Plug
（8.5）
Ｌ
4‐Rc1/8
(Both sides)
Unit dimensions
H
（
1 Ｐ）
36.8
8.5
8.5
7.2
9.2
−
H
（
3 R）
23
29
Manual override
Block-off plate
(-BP)
（
1 Ｐ）
47.9
LED indicator
Stn. 3
Stn. 4
10.2 (Pitch)
">