Koganei Solenoid Valve JE Series Instruction manual

BK-UV002 Ver.1.0
Air Valve
SOLENOID VALVES JC JE SERIES
INSTRUCTION MANUAL Ver.1.0
Handling Instructions and Precautions
Plug connector
Solenoid
Internal circuit
● DC12V, DC24V
(Standard type)
Solenoid with LED indicator and surge suppression
Lead wire
（＋）
Red
（Red）
Attaching and removing plug connector
Side mounting precautions (JE series)
Use fingers to insert the connector into the
pin, push it in until the lever claw latches onto
the protruded section of the connector
housing, and complete the connection.
To remove the connector, squeeze the lever
along with the connector, lift the lever claw up
from the protruded section of the connector
housing, and pull it out.
When using a JE series single solenoid valve
unit in a side mounting, as shown in the
diagram below, mounting base -22 for the side
mounting is required, because the fitting
interferes with the mounting surface. The
TS6-M5 and TL6-M5 quick fitting standard
types for the 6mm tube cannot be mounted.
Use the hexagon socket straight fitting or the
quick fitting mini type instead.
Lead wire
Black（−）
Protruded section
Pin
Housing
● DC24V
(Low current, quick response types)
Solenoid with LED indicator and surge suppression
Lever
Connector
assembly
Lead wire
Red（＋）
Lead wire
Black（−）
（Red）
Indication of
polarity (DC)
Connector
Contact
Timer
circuit
Manual override
Non-locking type
Cautions: 1. Do not apply megger between the
pins.
2. Leakage current inside the circuit
could result in failure of the solenoid
valve to return to the rest position or
other erratic operation. Always use it
at less than the allowable leakage
current shown in the solenoid specifications on p.235, and 249. If circuit
conditions, etc. cause the leakage
current to exceed the maximum
allowable leakage current, consult
us.
3. For the double solenoid configuration, avoid energizing both solenoids
simultaneously.
4. The standard housing type is colored
blue, while the low current type is
light blue, and the quick response
type is white.
5. The low current and quick response
types will not activate when the
power supply voltage is raised too
slowly. Always apply the appropriate
voltage.
Operating principles of low current
and quick response types
The low current and quick response types use
a timer circuit, as shown above, that achieves
power savings by switching to the holding
operations mode after a certain period of time
and operates at about 1/3 of the starting
power consumption.
● Power waveform for low current type
Power
consumption
Solenoid
valves
ON
0.55W
OFF
Reduced power
consumption
0.15W
Crimping of connecting lead wire and contact
To crimp lead wires into contacts, strip off
4mm [0.16in.] of the insulation from the end
of the lead wire, insert it into the contact,
and crimp it. Be sure to avoid catching the
insulation on the exposed wire crimping
section.
Exposed wire 4mm [0.16in.]
Contact
Hook
Lead wire
Equivalent to
Insulation crimp
AWG＃22〜＃28
tab
Insulation
Exposed wire
(Maximum outer diameter: φ1.7)
crimping section
To operate the manual override, press it all the
way down.
For the single solenoid, the valve works the
same as when in the energized state as long
as the manual override is pushed down, and
returns to the rest position upon release.
For the double solenoid, pressing the manual
override on the 14 (SA) side switches the
14 (SA) to the energized state, and the valve
remains in that state even after the manual
override is released. To return it to the rest
position, operate the manual override on the
12 (SB) side. This is the same for the solenoid
12 (SB).
Cautions: 1. Do not pull hard on the lead wire.
2. Always use a dedicated tool for
crimping of connecting lead wire and
contact.
Contact: Model 702062-2M
Manufactured by Sumiko Tech, Inc.
Crimping tool: Model F1-702062
Manufactured by Sumiko Tech, Inc.
PU
SH
Attaching and removing contact and connector
Insert the contact with lead wire into a plug
connector □ hole until the contact hook
latches on and is secured to the plug
connector. Confirm that the lead wire cannot
be easily pulled out.
To remove it, insert a tool with a fine tip
(such as a small screwdriver) into the
rectangular hole on the side of the plug
connector to push up on the hook, and then
pull out the lead wire.
Locking type
To lock the manual override, use a small
screwdriver to push down on the manual
override all the way down and turn it clockwise
45 degrees. When locked, turning the manual
override 45 degrees in the counterclockwise
direction returns it to its rest position, and
releases the lock. (Excluding the quick
response type)
Start-up time（200ms or below）
● Power waveform for quick response type
Power
consumption
Solenoid
valves
3W
1.1W
ON
OFF
Reduced power
consumption
Start-up time（30ms or below）
Cautions: 1. Do not pull hard on the lead wire.
It could result in defective contacts, breaking wires, etc.
2. If the pin is bent, use a small
screwdriver, etc. to gently straighten out the pin, and then complete
the connection to the plug
connector.
TURN
Handling Instructions and Precautions
Manifold
Lever type (JE series only)
Mounting on a DIN rail (A type manifold)
● Vertical mounting
To lock the manual override, push the manual
lever all the way down and turn it clockwise 90
degrees. When locked, turning the manual
lever 90 degrees in the counterclockwise
direction returns it to its rest position and
releases the lock. When the manual lever is
not turned, this type acts just like the nonlocking type, and the valve remains in the
energized state as long as the manual lever is
pushed down, and returns to the rest position
upon release.
The manual lever is equipped with a safety
plate to avoid erroneous operation. Care
should be taken that the safety plate cannot
be operated when the manual lever is locked
in place.
With the DIN rail mounting bracket option, a
mounting bracket and mounting screw are
provided. First, use the mounting screw to
temporarily secure the mounting bracket on
the manifold.
When mounting the manifold in a vertical
direction, mount it so that the release lever
is pointing downward.
Mounting screw
1
（P）
3
（R）
1
（P）
● Mounting
qApproaching from the direction shown in
the diagram, let the mounting bracket
hook latches onto the DIN rail fringe, then
press down the manifold to secure the
bracket onto the DIN rail.
ON
PUSH
KEEP
Mounting bracket
3
（R）
Manual lever
Safety plate
Caution: Caution should be taken not to drop
the manifold.
Release lever
Mounting a valve on the manifold
When mounting a valve on the manifold, the
recommended tightening torque for the
valve mounting screw is 14.7N･cm {1.5kgf･
cm} [1.30in･lbf].
（P）
1
LOCK
Locked
position
90°
（R）
3
Push down and turn
●Safety plate operation
qCheck that the manual lever is in the off
position.
wSlide the center of the safety plate in the
direction shown by the arrow until it comes
to a stop, at a distance of about 3mm
[0.12in.]. In this position, the manual lever
can no longer be pushed in.
eTo release the safety plate, slide it in the
direction opposite to that shown by the
arrow until it comes to a stop.
Manual lever
(Off position)
Safety plate
KEEP
ON
PUSH
LOCK
Slide
Cautions: 1. The JC and JE series are pilot type solenoid valves. As a result, the manual
override button or manual lever cannot
switch the main valve without air supplied from the 1(P) port.
2. Always release the lock of the manual
override button or manual lever before
commencing normal operation.
3. Do not attempt to operate the manual
override button or manual lever with a
pin or other object having an extremely
fine tip. It could damage the button.
4. For the lever type, do not apply excessive force when sliding the safety plate.
It could result in a breakdown. (Recommended force: 3N)
wTo ensure that the mounting bracket is
firmly set against the bottom of the
manifold, tighten the mounting screw to
secure the DIN rail in place.
Recommended tightening torque:
98N･cm {10kgf･cm} [8.7in･lbf]
1
（P）
Tightening
3
（R）
Caution: Since the mounting bracket cannot slide
along the DIN rail once it is set onto the
rail, make sure to set the manifold in the
appropriate position beforehand.
● Removing
qLoosen the mounting screw and lift the
manifold off and away from the mounting
bracket.
wInsert a flatblade screwdriver, etc.
underneath the mounting bracket’s
release lever, and gently pry it away to
remove the mounting bracket.
1
（P）
3
（R）
Release lever
Tube
1. Attaching and removing tubes
For tube connection, insert an appropriate
size tube until it comes into contact with the
tube stopper, and lightly pull it to check the
connection.
For tube removal, push the tube against the
tube stopper, then push the release ring and
at the same time pull the tube out.
2. Either a nylon or urethane tube can be
used.
Use tubes with an outer diameter tolerance
within ±0.1mm [±0.004in.] of the nominal
diameter, and ensure the ovalness
(difference between large diameter and
small diameter) is 0.2mm [0.008in.] or less.
(Using Koganei tubes is recommended.)
Cautions: 1. Do not use extra-soft tubes since
their pull-out strength is significantly
reduced.
2. Only use tubes without scratches on
their outer surfaces. If a scratch
occurs during repeated use, cut off
the scratched section.
3. Do not bend the tube excessively
near the fittings.The minimum
bending radius is as shown in the
table below.
4. When attaching or removing tubes,
always stop the air supply. In
addition, always confirm that air has
been completely exhausted from the
manifold.
mm [in.]
Tube size
Cautions: Spring force from the mounting bracket’s
plate could cause the bracket to pop out
during the removal operation. To ensure
safety, proceed with caution during the
operation. In addition, always use a flatbrade screwdriver, etc. when removing
the mounting bracket from the DIN rail.
Never use your fingers because of the
danger of serious injury due to the
potential strong forces.
Minimum bending radius
Nylon tube
Urethane tube
φ4
20 [0.79]
10 [0.39]
φ6
30 [1.18]
15 [0.59]
φ8
50 [1.97]
20 [0.79]
φ3
7 [0.28]
JC SERIES SPECIFICATIONS
Specifications
Basic Models and Functions
JC10□F1Note
JC10□F2Note
JC10□F3Note
JC10□F4Note
JC10□A1Note
JC10□A2Note
JC10□A3Note
JC10□A4Note
Basic model For direct piping,
F type manifolds
For base piping,
A type manifolds
Item
Number of positions
JC10□F5
JC10□F6
JC10□F7
JC10□F8
JC10□F9
JC10□A5
JC10□A6
JC10□A7
JC10□A8
JC10□A9
3 positions
2 positions
Number of ports
2, 3 ports
Valve function
Single solenoid NC, NO
5 ports
Single solenoid
Double solenoid
Closed center, Exhaust center,
Pressure center
Remark: For the optional specifications and order codes, see p.239.
Note: Valves with valve specifications F1, F2, F3, F4, A1, A2, A3, and A4 are for mounting on manifolds only, and cannot be used as single valve units.
Specifications
JC10□F1
JC10□F2
JC10□F3
JC10□F4
JC10□A1
JC10□A2
JC10□A3
JC10□A4
Basic model For direct piping,
F type manifolds
For base piping,
A type manifolds
Item
JC10□F5
JC10□F6
JC10□F7
JC10□F8
JC10□F9
JC10□A5
JC10□A6
JC10□A7
JC10□A8
JC10□A9
Media
Air
Operation type
Internal pilot type
Flow rate characteristicsNote 1
Sonic conductance C dm 3/(s・bar)
0.6
Port sizeNote 2
M5×0.8
Lubrication
Not required
Operating pressure range MPa {kgf/cm2 }[psi.]
Proof pressure
Response timeNote 3
ON/OFF
0.2〜0.7 {2〜7.1} [29〜102]
MPa {kgf/cm2 }[psi.]
ms
Maximum operating
Hz
frequency
0.25〜0.7 {2.5〜7.1} [36〜102]
1.05 {10.7} [152]
Standard type
10/20 or below
12 or below
10/30 or below
Low current type (L)
10/50 or below
12 or below
10/60 or below
Quick response type (S)
6/7 or below
6 or below
6/12 or below
50
―
Standard type
5
Low current type (L)
2
Quick response type (S)
ms
Minimum time to energize for self holdingNote 4
10
―
Operating temperature range (atmosphere and media) °C [°F]
m/s2 {G}
Shock resistance
5〜50 [41〜122]
1373.0 {140} (Axial direction 294.2 {30})
Mounting direction
1373.0 {140} (Axial direction 147.1 {15}) 1373.0 {140} (Axial direction 195.0 {20})
Any
Notes: 1. For details, see the flow rate characteristics on p.236.
2. For details, see the port size on p.237.
3. Values when air pressure is 0.5MPa [73psi.]. The values for the 3-position valves are switching time from the neutral position.
4. For double solenoid valve.
Solenoid Specifications
Rated voltage
Item
Operating voltage range
DC24V
(Standard type)
DC24V
(Low current type)
DC24V
(Quick response type)
10.8〜13.2
21.6〜26.4
21.6〜26.4
21.6〜26.4
（12±10％）
（24±10％）
（24±10％）
（24±10％）
―
Standard
type
Current (when rated voltage is applied) mA (r.m.s)
46
23
―
Power consumption
W
0.55
0.55
―
―
Low current type
Quick response type
V
DC12V
(Standard type)
Current (when rated Starting mA
voltage is applied)
Holding mA
―
―
23
125
46
Power consumption
―
―
6.3
Starting
W
―
―
0.55
3
Holding
W
―
―
0.15
1.1
Start-up time (standard time)
ms
―
―
200 or below
30 or below
Allowable leakage current
mA
2
1
0.5
4
Insulation resistance
MΩ
Color of LED indicator
Surge suppression (as standard)
Over 100 (value at DC500V megger)
Red
Flywheel diode
Flow Rate Characteristics
The test method for flow rate characteristics conforms to JIS B 8390:2000 (test method for pneumatic equipment — equipment for compressible fluids — flow rate
characteristics).
●When used as a single unit (with fittings)
Basic model
Flow path
Sonic conductance C
dm3/(s･bar)
Critical pressure ratio b
1（P）→ 4（A）
―
―
JC10□F5
1（P）→ 2（B）
―
―
JC10□F6
4（A）→ 5（R1）
―
―
2（B）→ 3（R2）
―
―
1（P）→ 4（A）
―
―
1（P）→ 2（B）
―
―
4（A）→ 5（R1）
―
―
Direct piping Note 1
JC10□F7
JC10□F8
JC10□F9
Effective area S
mm2〔Cv〕
2.80〔0.156〕
2.50〔0.139〕
2（B）→ 3（R2）
―
―
1（P）→ 4（A）
0.58
0.40
2.90〔0.161〕Note 3
JC10□A5
1（P）→ 2（B）
0.57
0.37
2.85〔0.158〕Note 3
JC10□A6
4（A）→ 5（R1）
0.51
0.29
2.55〔0.142〕Note 3
2（B）→ 3（R2）
0.61
0.26
3.05〔0.169〕Note 3
1（P）→ 4（A）
0.52
0.36
2.60〔0.144〕Note 3
1（P）→ 2（B）
0.53
0.33
2.65〔0.147〕Note 3
4（A）→ 5（R1）
0.49
0.27
2.45〔0.136〕Note 3
2（B）→ 3（R2）
0.55
0.27
2.75〔0.153〕Note 3
Flow path
Sonic conductance C
dm3/(s･bar)
Critical pressure ratio b
Effective area SNote 3
mm2〔Cv〕
Note 1
Base piping
(with sub-base)
JC10□A7
JC10□A8
JC10□A9
●When mounted on a manifold (with fittings)
Basic model
F type manifold Note 2
(direct piping type)
JC10□F1
JC10□F2
JC10□F3
JC10□F4
JC10□F5
JC10□F6
JC10□F7
JC10□F8
JC10□F9
A type manifold Note 2
(base piping type)
JC10□A1
JC10□A2
JC10□A3
JC10□A4
JC10□A5
JC10□A6
JC10□A7
JC10□A8
JC10□A9
1（P）→4（A）
0.66
0.54
3.30〔0.183〕
1（P）→2（B）
0.62
0.46
3.10〔0.172〕
4（A）→5（R1）
0.58
0.33
2.90〔0.161〕
2（B）→3（R2）
0.55
0.14
2.75〔0.153〕
1（P）→4（A）
0.56
0.41
2.80〔0.156〕
1（P）→2（B）
0.56
0.42
2.80〔0.156〕
4（A）→5（R1）
0.53
0.32
2.65〔0.147〕
2（B）→3（R2）
0.50
0.13
2.50〔0.139〕
1（P）→4（A）
0.61
0.33
3.05〔0.169〕
1（P）→2（B）
0.60
0.31
3.00〔0.167〕
4（A）→5（R1）
0.61
0.08
3.05〔0.169〕
2（B）→3（R2）
0.60
0.08
3.00〔0.167〕
1（P）→4（A）
0.54
0.29
2.70〔0.150〕
1（P）→2（B）
0.54
0.30
2.70〔0.150〕
4（A）→5（R1）
0.57
0.08
2.85〔0.158〕
2（B）→3（R2）
0.54
0.09
2.70〔0.150〕
Notes: 1. Quick fitting TSH6-M5Ms are mounted on connection ports 1(P), 2(B), and 4(A).
2. Quick fitting TSH6-M5Ms are mounted on connection ports 2(B) and 4(A).
3. Figures in effective area S are calculated based on sonic conductance C (S=5.0×C).
(Effective area S=3.0mm2〔Cv: 0.17〕)
MPa 0.7
Valve outlet pressure
0.6
0.5
0.4
0.3
0.2
0.1
0
100
200
300
400
Flow rate R/min (ANR)
1MPa = 145psi., 1R/min = 0.0353ft3/min
The graph uses flow rate calculations based on the discharge method.
● Use the flow rate as a guide.
●
Port Size
Port
（
2 B）
,（
4 A）
（
1 P）
3, （
5 R）
Direct piping
M5×0.8
M5×0.8
M3×0.5
Base piping (with sub-base)
M5×0.8
M5×0.8
M5×0.8
F type
M5×0.8
Rc1/8
Rc1/8
A type
M5×0.8
Rc1/8
Rc1/4
Port specification
Single unit
Manifold
Mass
Single Valve Unit Mass
Basic model
Mass
g [oz.]
Additional mass
-21 (with bottom mounting base)
-25 (with sub-base)
JC10□F1
JC10□F2
26 [0.92]
―
JC10□F5
26 [0.92]
4 [0.14]
JC10□F6
40 [1.41]
JC10□F3
JC10□F4
JC10□F7
JC10□F8
43 [1.52]
―
―
JC10□F9
JC10□A1
JC10□A2
JC10□A3
26 [0.92]
―
―
―
27 [0.95]
JC10□A4
JC10□A5
26 [0.92]
JC10□A6
40 [1.41]
JC10□A7
JC10□A8
43 [1.52]
JC10□A9
Manifold Mass
g [oz.]
Basic model
Mass calculation of each unit
(n = number of units)
JCM□F
(12.5×n)＋20 [(0.44×n)＋0.71]
JCM□A
(22.5×n)＋42 [(0.79×n)＋1.48]
Block-off plate
With DIN rail mounting
bracket
3 [0.11]
―
15 [0.53]
Calculation example: JCM8A
stn.1〜8 JC10A5-PS-D4
(22.5×8)＋42＋(26×8) = 430g [15.17oz.]
Operating Principles and Symbols
5-port, 2-position
Single solenoid
Double solenoid
14（SA）
4（A）
2（B）
14（SA）
4（A）
2（B）
5（R1）
1（P）
3（R2）
12
5（R1）
1（P）
3（R2）
12（SB）
JC10F5
JC10F6
De-energized
〔De-energized condition after
energizing solenoid 12 (SB)〕
Column
Plunger
Major Parts and Materials
Flapper
Piston
Solenoid
5（R1）
Manual override
2（B）
Synthetic rubber
Flapper
3（R2）
4（A）
Aluminum alloy
(anodized)
Lip seal
1（P）
5（R1）
Materials
Body
Stem
4（A）
Stem
Parts
Mounting base Mild steel (zinc plated)
Valve
1（P）
2（B）
3（R2）
Sub-base
Aluminum alloy (anodized)
Plunger
Valve body
Column
Magnetic stainless
steel
End cover
End cover
Plastic
Body
Aluminum alloy (anodized)
Lip seal
Manifold Block-off plate Mild steel (nickel plated)
Synthetic rubber
Seal
5-port, 3-position
〔Both 14 (SA) and 12 (SB) are de-energized〕
Closed center
4（A）
2（B）
JC10F7
Exhaust center
14（SA）
12（SB）
5（R1）
1（P）
3（R2）
4（A）
2（B）
JC10F8
5（R1）
4（A）
12（SB）
1（P）
4（A）
2（B）
JC10F9
12（SB）
5（R1）
4（A）
1（P）
2（B）
3（R2）
5（R1）
1（P）
3（R2）
5（R1）
4（A）
2（B）
Pressure center 14（SA）
14（SA）
1（P）
2（B）
3（R2）
3（R2）
5（R1）
1（P）
3（R2）
JC Series Single Valve Unit Order Codes
■ Sub-base
■ Manual override
■ Wiring specification
Without sub-base
Non-locking type
S type plug connector
Lead wire 300mm
Blank
Blank
With sub-base
Locking type Note4
-25
-81
-PS
S type plug connector
Lead wire 1000mm
L type plug connector
Lead wire 300mm
-PL
L type plug connector
Lead wire 1000mm
■ Valve specification
F1, A1: 2-port normally closed (NC)Note1
F2, A2: 2-port normally open (NO)Note1
-PS1
Note1
F3, A3: 3-port normally closed (NC)
F4, A4: 3-port normally open (NO)Note1
S type plug connector
Lead wire 3000mm
-PL1
L type plug connector
Lead wire 3000mm
F5, A5: 5-port 2-position, single solenoid
F6, A6: 5-port 2-position, double solenoid
F7, A7: 3-position, closed center
■ Mounting base
■ Muffler
Without mounting base
Without muffler
F8, A8: 3-position, exhaust center
-PS3
-PL3
F9, A9: 3-position, pressure center
S type plug connector
Without connector ass’y
Blank
Blank
With muffler
for direct piping Note2
With mounting base
■ Model
-PSN
JC10
Standard type
-21
With muffler
for sub-base piping Note3
JC10L
-D4
DC24V
JC10S
-D5
-GL
Quick response type
Model
Valve
specification
Mounting base
Sub-base
Muffler
Manual override
F1Note1
F2Note1
F3Note1
F4Note1
JC10
JC10L
JC10S
F5
Blank
Blank
-21
-81Note4
Blank
F6
F7
F8
F9
-75Note2
A1Note1
A2Note1
A3Note1
A4Note1
JC10
JC10L
JC10S
A5
A6
A7
A8
A9
Blank
-81Note4
Blank
Blank
-25
-75Note3
Notes: 1. Valves with valve specifications F1, F2, F3, F4, A1, A2, A3, and A4 are for mounting on
manifolds only, and cannot be used as single valve units.
2. The muffler thread for direct piping is M3×0.5 and the muffler cannot be used for sub-base piping.
3. When ordering the sub-base piping with muffler, always enter both -25 (sub-base) and -75 (muffler).
The muffler thread for sub-base piping is M5×0.8 and the muffler cannot be used for direct piping.
DC12V Note6
300mm = [11.8in.]
1000mm = [39in.]
3000mm = [118in.]
-75
Base piping
-PLN
Grommet typeNote5
Lead wire 300mm
■ Voltage
(moisture proof specification)
-75
Low current type
Direct piping
L type plug connector
Without connector ass’y
Wiring
specification
Voltage
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote5
-D4
-D5Note6
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote5
-D4
-D5Note6
4. The locking-type manual override is not available in the quick response type JC10S.
5. The grommet type is not available in the low current type JC10L and quick
response type JC10S.
6. The DC12V specification is not available in the low current type JC10L and quick
response type JC10S.
JC Series Manifold Order Codes
Left side
■ Manual override
■ Wiring specification
Non-locking type
S type plug connector
Lead wire 300mm
■ Voltage
L type plug connector
Lead wire 300mm
-D4
DC24V
Left side
-D5
Blank
Right side
Right side
DC12VNote 4
-PS
-PL
Locking typeNote2
S type plug connector
Lead wire 1000mm
■ Manifold specification ■ Mounting type
F type (direct piping type)
Direct mounting
L type plug connector
Lead wire 1000mm
■ Valve specification
F1, A1: 2-port normally closed (NC)
-81
F2, A2: 2-port normally open (NO)
-PS1
F3, A3: 3-port normally closed (NC)
F4, A4: 3-port normally open (NO)
F
Blank
A type (base piping type)
S type plug connector
Lead wire 3000mm
-PL1
L type plug connector
Lead wire 3000mm
F5, A5: 5-port 2-position, single solenoid
With DIN rail mounting
F6, A6: 5-port 2-position, double solenoid
bracket
(A type manifold only)
F7, A7: 3-position, closed center
F8, A8: 3-position, exhaust center
-PS3
-PL3
F9, A9: 3-position, pressure center
A
S type plug connector
Without connector ass’y
-DN
L type plug connector
Without connector ass’y
Mounting bracket is
included.
-PSN
-PLN
■ Model
Grommet typeNote 3
Lead wire 300mm
(moisture proof specification)
JC10
Standard type
JC10L
Low current type
-GL
JC10S
300mm = [11.8in.]
1000mm = [39in.]
3000mm = [118in.]
Quick response type
Model
Number of
units
Manifold
specification
Mounting type
Station
Model
Manifold model
F type manifold
(direct piping
type)
stn.1
・
・
・
stn.□
JC10
JC10L
JC10S
Note1
A type manifold
(base piping
type)
Manual
override
Wiring
specification
Voltage
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote3
-D4
-D5Note4
Mounting valve model
F
JCM
Valve
specification
2
・
・
・
20
F1
F2
F3
F4
F5
F6
F7
F8
F9
Blank
-81Note2
JCBP (for block-off plate)
A
Blank
-DN
stn.1
・
・
・
stn.□
Note1
JC10
JC10L
JC10S
A1
A2
A3
A4
A5
A6
A7
A8
A9
Blank
-81Note2
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote3
JCBP (for block-off plate)
Notes: 1. The valve mounting location is from the left side of the manifold.
2. The locking-type manual override is not available in the quick response type JC10S.
3. The grommet type is not available in the low current type JC10L and quick response type JC10S.
4. The DC12V specification is not available in the low current type JC10L and quick response type JC10S.
-D4
-D5Note4
JC Series Additional Parts Order Codes
Block-off plate (block-off plate and 2 mounting screws)
JCBP
Common connector assembly
EAZ -
Connector-related
EAZ Connector specification
P : Connector, lead wire length 300mm [11.8in.]
P1 : Connector, lead wire length 1000mm [39in.]
P3 : Connector, lead wire length 3000mm [118in.]
PN : Connector, without lead wire (contacts included)
Connector specification
PA ：Positive common A type, connector, lead wire length 300mm [11.8in.]
PA1 ：Positive common A type, connector, lead wire length 1000mm [39in.]
PA3 ：Positive common A type, connector, lead wire length 3000mm [118in.]
PB ：Positive common B type, connector, lead wire length 300mm [11.8in.]
PB1 ：Positive common B type, connector, lead wire length 1000mm [39in.]
PB3 ：Positive common B type, connector, lead wire length 3000mm [118in.]
PC ：Positive common C type, connector, lead wire length 300mm [11.8in.]
PC1 ：Positive common C type, connector, lead wire length 1000mm [39in.]
PC3 ：Positive common C type, connector, lead wire length 3000mm [118in.]
CPN ：Positive common, connector, without lead wire
(short bar and contacts included)
A type: EAZ-PA□ ※
DIN rail mounting bracket (with screws)
Black (−)
Red (＋)
JCZ -DN
B type: EAZ-PB□ ※
Red (＋) (For common wiring)
Black (−)
C type: EAZ-PC□ ※
Red (＋) (For common wiring)
Black (−)
Red (＋)
※Lead wire length
Blank：300mm [11.8in.]
1：1000mm [39in.]
3：3000mm [118in.]
Application example
A type B type B type B type B type C type
Dimensions of JC Series Single Valve Unit (mm)
5-port, single solenoid
JC10□F5-PL
30
（300）
10
22
2-φ2.1
(Mounting hole)
For -75
Manual override
2-φ1.7 Counterbore φ3.2
Depth 1 (Mounting hole)
65.4
PR
(Built-in muffler)
24.8
22.5
LED indicator
2-M3×0.5
2.8
12
2
（B）
9.3
13.1
3
（R2）
4
（A）
12.7 9.8
16.6
9
1
（P）
φ6
17.6
8.4 8.4
5（R1）
7.6
3-Ｍ5×0.8
14
5-port, single solenoid (with sub-base)
JC10□A5-25-PL
（46.7）
16
（300）
10
30
11
22
5
14
Manual override
24.8
2-φ3.2
(Mounting hole)
For -75
3
（R）
16.5
27
φ8
4-M5×0.8
3
1.1
2
（B）
12.3
33
1
（P）
65.4
4
（A）
20.7
PR
(Built-in muffler)
2
（30.7）
8.1
22.5
LED indicator
5
17
11
20
14
34
Options
●Locking type manual override: -81
●Grommet: -GL
●S type plug connector: -PS
19.6 （300）
24
LED indicator
LED indicator
22
28
B
(Overall length of valve)
（300）
27.5
C
4-
14
22.5
18.5
24.8
22
3
5
1.2
2
（B）
A
(Overall length of valve)
●Mounting base: -21
2-φ3.5
(Mounting hole)
mm
Code
A
B
JC10F5, JC10A5
65.4
70.4
JC10LF5, JC10LA5, JC10SF5, JC10SA5
−
70.4
Model
Remark
Overall length to the end of the valve
Dimensions of JC Series Single Valve Unit (mm)
5-port, double solenoid
JC10□F6-PL
12
30
（300）
10
22
14
24.8
22.5
LED indicator
Manual override
2-PR
(Built-in muffler)
2-φ1.7 Counterbore φ3.2
Depth 1 (Mounting hole)
3（R2）
4
（A）
9.8
9
φ6
95.6
For -75
1（P）
16.6
8.4 8.4
5（R1）
2
（B）
2-M3×0.5
2.8
42.9
2-φ2.1
(Mounting hole)
39.5
43.3
47.8
3-Ｍ5×0.8
7.6
5-port, double solenoid (with sub-base)
JC10□A6-25-PL
（46.7）
（300）
34
16
30
20
11
22
17
14
2
10
24.8
For -75
16.5
33
1
（P）
2-PR
(Built-in muffler)
4-M5×0.8
5
2-φ3.2
(Mounting hole)
（30.7）
11
8.1
3
3
（R）
φ8
27
95.6
12.3
2
（B）
20.7
4
（A）
Manual override
31.3
LED indicator
22.5
5
14
Dimensions of JC Series Single Valve Unit (mm)
5-port, 3-position
12
30
JC10□F7-PL
JC10□F8-PL
JC10□F9-PL
（300）
10
22
14
Manual override
24.8
22.5
LED indicator
2-PR
(Built-in muffler)
2-φ1.7 Counterbore φ3.2
Depth 1 (Mounting hole)
φ6
3（R2）
4
（A）
9.8
105.6
9
For -75
1（P）
16.6
8.4 8.4
5（R1）
2
（B）
3-Ｍ5×0.8
51.9
2-φ2.1
(Mounting hole)
48.5
52.3
56.8
2-M3×0.5
2.8
7.6
5-port, 3-position (with sub-base)
（46.7）
16
（300）
34
20
30
11
22
17
14
2
10
LED indicator
24.8
22.5
5
14
Manual override
2-PR
(Built-in muffler)
1
（P）
3
3
（R）
16.5
33
27
φ8
105.6
12.3
2
（B）
20.7
4
（A）
4-M5×0.8
40.3
5
For -75
8.1
JC10□A7-25-PL
JC10□A8-25-PL
JC10□A9-25-PL
11
2-φ3.2
(Mounting hole)
（30.7）
Options
●Locking type manual override: -81
●Grommet: -GL
●S type plug connector: -PS
24
19.6 （300）
22
24.8
LED indicator
Code
A
B
JC10F6, JC10A6
95.6
105.6
JC10F7〜JC10F9, JC10A7〜JC10A9
105.6
115.6
−
105.6
−
115.6
Model
JC10LF6, JC10LA6, JC10SF6, JC10SA6
JC10LF7〜JC10LF9, JC10LA7〜JC10LA9
JC10SF7〜JC10SF9, JC10SA7〜JC10SA9
Remark
Overall length to the opposite end of the solenoid
（300）
B
(Overall length of valve)
27.5
A
(Overall length of valve)
22.5
18.5
LED indicator
mm
mm
Dimensions of JC Series Manifold (mm)
Manifold for combination mounting of 2, 3, 5-port valves
JCM□F
（46.7）
(direct piping type)
（300）
L
14
30
22
9
LED indicator
10.5 (Pitch)
Manual override
M5×0.8
10
2-φ4.5 (Mounting hole)
24.8
PR
(Built-in muffler)
3（R）
3（R）
4（A）
4（A）
2（B）
2（B）
2（B）
38
4（A）
1（P）
1（P）
30.3
9
39.3
0.1
2（B）
23
12.6 9.8
14.5
31
95.6
4（A）
105.6
65.4
4-Rc1/8 (both sides)
〔Installation example〕
4
JCM6F
stn.1 JC10F3-PL-D4
stn.2 JC10F4-PL-D4
stn.3 JC10F5-PL-D4
stn.4 JC10F6-PL-D4
stn.5 JC10F7-PL-D4
stn.6 JCBP
P
stn.3
stn.4
stn.5 stn.6
14
stn.2
16
（30.7）
stn.1
（4）
Unit dimensions
Number
of units
2
L
P
38.5
30.5
3
49.0
41.0
4
59.5
51.5
5
70.0
62.0
6
80.5
72.5
7
91.0
83.0
8
101.5
93.5
9
112.0
104.0
10
122.5
114.5
11
133.0
125.0
12
143.5
135.5
13
154.0
146.0
14
164.5
156.5
15
175.0
167.0
16
185.5
177.5
17
196.0
188.0
18
206.5
198.5
19
217.0
209.0
20
227.5
219.5
Dimensions of JC Series Manifold (mm)
Manifold for combination mounting of 2, 3, 5-port valves
JCM□A
（300）
55.7
(base piping type)
L
15
30
10
22
10.5（Pitch）
10
LED indicator
PR
(Built-in muffler)
Manual override
2-φ4.5
(Mounting hole)
24.8
2-Rc1/4 (both sides)
65.4
2-Rc1/8 (both sides)
47
105.6
25
95.6
0.6
30.8
18
39.8
3.1
1（P）
17
35
3（R）
11
〔Installation example〕
5
JCM6A
stn.1 JC10A3-PL-D4
stn.2 JC10A4-PL-D4
stn.3 JC10A5-PL-D4
stn.4 JC10A6-PL-D4
stn.5 JC10A7-PL-D4
stn.6 JCBP
P
stn.1
stn.2
stn.3
（5）
stn.4
stn.5
stn.6
Plug 2(B) when mounting JC10※A1,※A3
4（A）
3.5
2.5
6.5 11
2（B）
25
（39.7）
14
2-Ｍ5×0.8 (per each station)
Plug 4(A) when mounting JC10※A2,※A4
●DIN rail mounting bracket (-DN)
（7.3）
2
（48.6）
1（P）
（5.2）
3（R）
24.5
Unit dimensions
Number
of units
2
L
P
40.5
30.5
3
51.0
41.0
4
61.5
51.5
5
72.0
62.0
6
82.5
72.5
7
93.0
83.0
8
103.5
93.5
9
114.0
104.0
10
124.5
114.5
11
135.0
125.0
12
145.5
135.5
13
156.0
146.0
14
166.5
156.5
15
177.0
167.0
16
187.5
177.5
17
198.0
188.0
18
208.5
198.5
19
219.0
209.0
20
229.5
219.5
JE SERIES SPECIFICATIONS
Specifications
Basic Models and Functions
JE12□F1Note
JE12□F2Note
JE12□F3Note
JE12□F4Note
JE12□A1Note
JE12□A2Note
JE12□A3Note
JE12□A4Note
Basic model For direct piping,
F type manifolds
For base piping,
A type manifolds
Item
Number of positions
JE12□F5
JE12□F6
JE12□F7
JE12□F8
JE12□F9
JE12□A5
JE12□A6
JE12□A7
JE12□A8
JE12□A9
3 positions
2 positions
Number of ports
2, 3 ports
Valve function
Single solenoid NC, NO
5 ports
Single solenoid
Double solenoid
Closed center, Exhaust center,
Pressure center
Remark: For the optional specifications and order codes, see p.253.
Note: Valves with valve specifications F1, F2, F3, F4, A1, A2, A3, and A4 are for mounting on manifolds only, and cannot be used as single valve units.
Specifications
JE12□F1
JE12□F2
JE12□F3
JE12□F4
JE12□A1
JE12□A2
JE12□A3
JE12□A4
Basic model For direct piping,
F type manifolds
For base piping,
A type manifolds
Item
JE12□F5
JE12□F6
JE12□F7
JE12□F8
JE12□F9
JE12□A5
JE12□A6
JE12□A7
JE12□A8
JE12□A9
Media
Air
Operation type
Internal pilot type
Flow rate characteristicsNote 1
Sonic conductance C dm 3/(s・bar)
Base piping (A type): 1.9
Direct piping (F type): M5×0.8, Base piping (A type): Rc1/8
Port sizeNote 2
Lubrication
Not required
Operating pressure range MPa {kgf/cm2 }[psi.]
Proof pressure
0.2〜0.7 {2〜7.1} [29〜102]
MPa {kgf/cm2 }[psi.]
Note 3
Response time
ON/OFF
ms
Maximum operating
Hz
frequency
1.05 {10.7} [152]
Standard type
12/28 or below
20 or below
12/30 or below
Low current type (L)
12/60 or below
20 or below
12/60 or below
Quick response type (S)
6/10 or below
8 or below
6/10 or below
50
―
Standard type
5
Low current type (L)
2
Quick response type (S)
ms
Minimum time to energize for self holdingNote 4
10
―
Operating temperature range (atmosphere and media) °C [°F]
m/s2 {G}
Shock resistance
5〜50 [41〜122]
1373.0 {140} (Axial direction 294.2 {30})
Mounting direction
1373.0 {140} (Axial direction 245.0 {25})
Any
Notes: 1. For details, see the flow rate characteristics on p.250.
2. For details, see the port size on p.251.
3. Values when air pressure is 0.5MPa [73psi.]. The values for the 3-position valves are the switching time from the neutral position.
4. For double solenoid valve.
Solenoid Specifications
Rated voltage
Item
Operating voltage range
DC24V
(Standard type)
DC24V
(Low current type)
DC24V
(Quick response type)
10.8〜13.2
21.6〜26.4
21.6〜26.4
21.6〜26.4
（12±10％）
（24±10％）
（24±10％）
（24±10％）
―
Standard
type
Current (when rated voltage is applied) mA (r.m.s)
46
23
―
Power consumption
W
0.55
0.55
―
―
Low current type
Quick response type
V
DC12V
(Standard type)
Current (when rated Starting mA
voltage is applied)
Holding mA
―
―
23
125
46
Power consumption
―
―
6.3
Starting
W
―
―
0.55
3
Holding
W
―
―
0.15
1.1
Start-up time (standard time)
ms
―
―
200 or below
30 or below
Allowable leakage current
mA
2
1
0.5
4
Insulation resistance
MΩ
Color of LED indicator
Surge suppression (as standard)
Over 100 (value at DC500V megger)
Red
Flywheel diode
Flow Rate Characteristics
The test method for flow rate characteristics conforms to JIS B 8390:2000 (test method for pneumatic equipment — equipment for compressible fluids — flow rate
characteristics).
●When used as a single unit (with fittings)
Basic model
Direct piping
Flow path
Sonic conductance C
dm3/(s･bar)
Critical pressure ratio b
Effective area S Note 5
mm2〔Cv〕
1（P）→ 4（A）
0.81
0.55
4.05〔0.225〕
JE12□F5
1（P）→ 2（B）
0.81
0.54
4.05〔0.225〕
JE12□F6
4（A）→ 5（R1）
0.75
0.44
3.75〔0.208〕
2（B）→ 3（R2）
0.76
0.43
3.80〔0.211〕
1（P）→ 4（A）
0.80
0.51
4.00〔0.222〕
1（P）→ 2（B）
0.80
0.52
4.00〔0.222〕
4（A）→ 5（R1）
0.71
0.41
3.55〔0.197〕
2（B）→ 3（R2）
0.72
0.43
3.60〔0.200〕
1（P）→ 4（A）
1.91
0.19
9.55〔0.531〕
JE12□A5
1（P）→ 2（B）
1.93
0.18
9.65〔0.536〕
JE12□A6
4（A）→ 5（R1）
1.90
0.15
9.50〔0.528〕
2（B）→ 3（R2）
1.90
0.12
9.50〔0.528〕
1（P）→ 4（A）
1.42
0.20
7.10〔0.394〕
1（P）→ 2（B）
1.49
0.21
7.45〔0.414〕
4（A）→ 5（R1）
1.37
0.18
6.85〔0.381〕
2（B）→ 3（R2）
1.28
0.14
6.40〔0.356〕
Flow path
Sonic conductance C
dm3/(s･bar)
Critical pressure ratio b
Effective area S Note 5
mm2〔Cv〕
Note 1
JE12□F7
JE12□F8
JE12□F9
Base piping Note 2
(with sub-base)
JE12□A7
JE12□A8
JE12□A9
●When mounted on a manifold (with fittings)
Basic model
F type manifold Note 3
(direct piping type)
JE12□F1
JE12□F2
JE12□F3
JE12□F4
JE12□F5
JE12□F6
JE12□F7
JE12□F8
JE12□F9
A type manifold Note 4
(base piping type)
JE12□A1
JE12□A2
JE12□A3
JE12□A4
JE12□A5
JE12□A6
JE12□A7
JE12□A8
JE12□A9
1（P）→4（A）
0.88
0.64
4.40〔0.244〕
1（P）→2（B）
0.88
0.63
4.40〔0.244〕
4（A）→5（R1）
0.90
0.20
4.50〔0.250〕
2（B）→3（R2）
0.91
0.20
4.55〔0.253〕
1（P）→4（A）
0.84
0.59
4.20〔0.233〕
1（P）→2（B）
0.85
0.59
4.25〔0.236〕
4（A）→5（R1）
0.85
0.20
4.25〔0.236〕
2（B）→3（R2）
0.85
0.21
4.25〔0.236〕
1（P）→4（A）
1.62
0.38
8.10〔0.450〕
1（P）→2（B）
1.63
0.38
8.15〔0.453〕
4（A）→5（R1）
1.82
0.10
9.10〔0.506〕
2（B）→3（R2）
1.77
0.18
8.85〔0.492〕
1（P）→4（A）
1.34
0.40
6.70〔0.372〕
1（P）→2（B）
1.37
0.24
6.85〔0.381〕
4（A）→5（R1）
1.34
0.08
6.70〔0.372〕
2（B）→3（R2）
1.26
0.17
6.30〔0.350〕
Notes: 1. Quick fitting TSH6-M5Ms are mounted on connection ports 1(P), 2(B), and 4(A).
2. Quick fitting TS8-01s are mounted on connection ports 1(P), 2(B), and 4(A).
3. Quick fitting TSH6-M5Ms are mounted on connection ports 2(B) and 4(A).
4. Quick fitting TS6-01Ms are mounted on connection ports 2(B) and 4(A).
5. Figures in effective area S are calculated based on sonic conductance C (S=5.0×C).
MPa 0.7
MPa 0.7
0.6
0.6
Valve outlet pressure
Direct piping type
(Effective area S = 4.4mm2〔Cv: 0.25〕)
Valve outlet pressure
Base piping type
(Effective area S = 9.5mm2〔Cv: 0.53〕)
0.5
0.4
0.3
0.5
0.4
0.3
0.2
0.2
0.1
0.1
0
0
200
400
600
800
1000
Flow rate R/min (ANR)
100
200
300
400
500
Flow rate R/min (ANR)
1MPa = 145psi., 1R/min = 0.0353ft3/min
Graphs use flow rate calculations based on the discharge method.
● Use the flow rate as a guide.
●
250
Port Size
Port
（
2 B）
,（
4 A）
（
1 P）
3, （
5 R）
M5×0.8
M5×0.8
M5×0.8
Base piping (with sub-base)
Rc1/8
Rc1/8
Rc1/8
F type
M5×0.8
Rc1/8
Rc1/8
A type
Rc1/8
Rc1/8
Rc1/8
Port specification
Single unit
Direct piping
Manifold
Mass
Single Valve Unit Mass
Basic model
Mass
g [oz.]
Additional mass
-21 (with bottom mounting base)
-22 (with side mounting base)
39 [1.38]
―
―
JE12□F5
36 [1.27]
6 [0.21]
JE12□F6
52 [1.83]
-25 (with sub-base)
JE12□F1
JE12□F2
JE12□F3
JE12□F4
JE12□F7
JE12□F8
55 [1.94]
―
5 [0.18]
―
JE12□F9
JE12□A1
JE12□A2
JE12□A3
39 [1.38]
―
―
―
―
―
48 [1.69]
Block-off plate
With DIN rail mounting
bracket
7 [0.25]
―
15 [0.53]
JE12□A4
JE12□A5
36 [1.27]
JE12□A6
52 [1.83]
JE12□A7
JE12□A8
55 [1.94]
JE12□A9
Manifold Mass
g [oz.]
Basic model
Mass calculation of each unit
(n = number of units)
JEM□F
(13×n)＋17 [(0.46×n)＋0.60]
JEM□A
(32×n)＋59 [(1.13×n)＋2.08]
Calculation example: JEM8A
stn.1〜8 JE12A5-PS-D4
(32×8)＋59＋(36×8) = 603g [21.27oz.]
Operating Principles and Symbols
5-port, 2-position
Single solenoid
Double solenoid
14（SA）
4（A）
2（B）
14（SA）
4（A）
2（B）
5（R1）
1（P）
3（R2）
12
5（R1）
1（P）
3（R2）
12（SB）
JE12F5
JE12F6
De-energized
〔De-energized condition after
energizing solenoid 12 (SB)〕
Column
Plunger
Major Parts and Materials
Flapper
Piston
5（R1）
Solenoid
Manual override
Aluminum alloy
(anodized)
Lip seal
1（P）
Flapper
2（B）
5（R1）
Materials
Body
Stem
4（A）
Stem
Parts
3（R2）
4（A）
Valve
1（P）
2（B）
3（R2）
Lip seal
Valve body
End cover
Synthetic rubber
Mounting base Mild steel (nickel plated)
Sub-base
Aluminum alloy (anodized)
Plunger
Column
Magnetic stainless
steel
End cover
Plastic
Body
Aluminum alloy (anodized)
Manifold Block-off plate Mild steel (nickel plated)
Synthetic rubber
Seal
5-port, 3-position
〔Both 14 (SA) and 12 (SB) are de-energized〕
Closed center
4（A）
2（B）
JE12F7
Exhaust center
14（SA）
12（SB）
5（R1）
1（P）
3（R2）
4（A）
2（B）
JE12F8
5（R1）
4（A）
12（SB）
1（P）
14（SA）
4（A）
2（B）
JE12F9
12（SB）
5（R1）
4（A）
1（P）
2（B）
3（R2）
5（R1）
1（P）
3（R2）
5（R1）
4（A）
2（B）
Pressure center
14（SA）
1（P）
2（B）
3（R2）
3（R2）
5（R1）
1（P）
3（R2）
JE Series Single Valve Unit Order Codes
■ Mounting base
Without mounting base
Blank
With mounting base
(for bottom mounting)
■ Muffler
■ Manual override
■ Wiring specification
Without muffler
Non-locking type
S type plug connector
Lead wire 300mm
Blank
Blank
-PS
With muffler
for direct pipingNote2
L type plug connector
Lead wire 300mm
-PL
Locking type Note4
S type plug connector
Lead wire 1000mm
L type plug connector
Lead wire 1000mm
■ Valve specification
F1, A1: 2-port normally closed (NC)Note1
F2, A2: 2-port normally open (NO)Note1
F3, A3: 3-port normally closed (NC)Note1
-75
-81
With muffler
for sub-base pipingNote3
Lever type (with erroneous
operation prevention mechanism)
-21
With mounting base
(for side mounting)
F4, A4: 3-port normally open (NO)Note1
S type plug connector
Lead wire 3000mm
F5, A5: 5-port 2-position, single solenoid
F6, A6: 5-port 2-position, double solenoid
F7, A7: 3-position, closed center
F8, A8: 3-position, exhaust center
-PS1
-22
-75
L type plug connector
Lead wire 3000mm
-84
Mounting base for side
mounting is supplied
with a valve.
F9, A9: 3-position, pressure center
-PL1
-PS3
■ Sub-base
S type plug connector
Without connector ass’y
Without sub-base
-PSN
Blank
-PL3
L type plug connector
Without connector ass’y
-PLN
■ Model
Grommet typeNote5
Lead wire 300mm
■ Voltage
(moisture proof specification)
With sub-base
JE12
Standard type
-D4
DC24V
JE12L
Low current type
-25
-D5
-GL
JE12S
300mm = [11.8in.]
1000mm = [39in.]
3000mm = [118in.]
Quick response type
Model
Valve
specification
Mounting base
Sub-base
Muffler
Manual override
F1Note1
F2Note1
F3Note1
F4Note1
Direct piping
JE12
JE12L
JE12S
F5
F6
F7
F8
F9
Blank
Blank
-21
-22
-81Note4
-84
Blank
-75Note2
Blank
-22
A1Note1
A2Note1
A3Note1
A4Note1
Base piping
DC12VNote6
JE12
JE12L
JE12S
Blank
A5
A6
A7
A8
A9
Blank
Blank
-25
-75Note3
Notes: 1. Valves with valve specifications F1, F2, F3, F4, A1, A2, A3, and A4 are for mounting on
manifolds only, and cannot be used as single valve units.
2. The muffler thread for direct piping is M5×0.8 and the muffler cannot be used for sub-base piping.
3. When ordering the sub-base piping with muffler, always enter both -25 (sub-base) and -75 (muffler).
The muffler thread for sub-base piping is Rc1/8 and the muffler cannot be used for direct piping.
-81Note4
-84
Wiring
specification
Voltage
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote 5
-D4
-D5Note6
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote5
-D4
-D5Note6
4. The locking-type manual override is not available in the quick response type JE12S.
5. The grommet type is not available in the low current type JE12L and quick
response type JE12S.
6. The DC12V specification is not available in the low current type JE12L and quick
response type JE12S.
JE Series Manifold Order Codes
■ Manual override
■ Wiring specification
Non-locking type
S type plug connector
Lead wire 300mm
Left side
Left side
■ Voltage
L type plug connector
Lead wire 300mm
-D4
DC24V
-D5
DC12VNote4
Blank
Right side
-PS
Right side
-PL
Locking typeNote 2
S type plug connector
Lead wire 1000mm
■ Manifold specification ■ Mounting type
F type (direct piping type)
Direct mounting
■ Valve specification
F1, A1: 2-port normally closed (NC)
F2, A2: 2-port normally open (NO)
F3, A3: 3-port normally closed (NC)
-81
Lever type (with erroneous
operation prevention mechanism)
F4, A4: 3-port normally open (NO)
F
Blank
A type (base piping type)
With DIN rail mounting
bracket
(A type manifold only)
L type plug connector
Lead wire 1000mm
-PS1
S type plug connector
Lead wire 3000mm
F5, A5: 5-port 2-position, single sol.
F6, A6: 5-port 2-position, double sol.
-PL1
L type plug connector
Lead wire 3000mm
-84
F7, A7: 3-position, closed center
F8, A8: 3-position, exhaust center
-PS3
-PL3
F9, A9: 3-position, pressure center
A
S type plug connector
Without connector ass’y
-DN
L type plug connector
Without connector ass’y
Mounting bracket is
supplied with a
manifold.
-PSN
-PLN
■ Model
Grommet typeNote 3
Lead wire 300mm
(moisture proof specification)
JE12
Standard type
300mm = [11.8in.]
1000mm = [39in.]
3000mm = [118in.]
JE12L
Low current type
-GL
JE12S
Quick response type
Model
Number of
units
Manifold
specification
Mounting type
Station
Model
Manifold model
F type manifold
(direct piping
type)
stn.1
・
・
・
stn.□
JE12
JE12L
JE12S
Note1
A type manifold
(base piping
type)
Manual
override
Wiring
specification
Voltage
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote3
-D4
-D5Note4
Mounting valve model
F
JEM
Valve
specification
2
・
・
・
20
F1
F2
F3
F4
F5
F6
F7
F8
F9
Blank
-81Note2
-84
JEBP (for block-off plate)
A
Blank
-DN
stn.1
・
・
・
stn.□
Note1
JE12
JE12L
JE12S
A1
A2
A3
A4
A5
A6
A7
A8
A9
Blank
-81Note2
-84
-PS
-PS1
-PS3
-PSN
-PL
-PL1
-PL3
-PLN
-GLNote3
-D4
-D5Note4
JEBP (for block-off plate)
Notes: 1. The valve mounting location is from the left side of the manifold.
2. The locking-type manual override is not available in the quick response type JE12S.
3. The grommet type is not available in the low current type JE12L and quick response type JE12S.
4. The DC12V specification is not available in the low current type JE12L and quick response type JE12S.
254
JE Series Additional Parts Order Codes
Block-off plate (block-off plate and 2 mounting screws)
JEBP
Common connector assembly
EAZ -
Connector-related
EAZ Connector specification
P : Connector, lead wire length 300mm [11.8in.]
P1 : Connector, lead wire length 1000mm [39in.]
P3 : Connector, lead wire length 3000mm [118in.]
PN : Connector, without lead wire (contacts included)
Connector specification
PA ：Positive common A type, connector, lead wire length 300mm [11.8in.]
PA1 ：Positive common A type, connector, lead wire length 1000mm [39in.]
PA3 ：Positive common A type, connector, lead wire length 3000mm [118in.]
PB ：Positive common B type, connector, lead wire length 300mm [11.8in.]
PB1 ：Positive common B type, connector, lead wire length 1000mm [39in.]
PB3 ：Positive common B type, connector, lead wire length 3000mm [118in.]
PC ：Positive common C type, connector, lead wire length 300mm [11.8in.]
PC1 ：Positive common C type, connector, lead wire length 1000mm [39in.]
PC3 ：Positive common C type, connector, lead wire length 3000mm [118in.]
CPN ：Positive common, connector, without lead wire
(short bar and contacts included)
A type: EAZ-PA□ ※
Black (−)
Red (＋)
DIN rail mounting bracket (with screws)
JEZ -DN
B type: EAZ-PB□ ※
Red (＋) (For common wiring)
Black (−)
C type: EAZ-PC□ ※
Red (＋) (For common wiring)
Black (−)
Red (＋)
※Lead wire length
Blank：300mm [11.8in.]
1：1000mm [39in.]
3：3000mm [118in.]
Application example
A type B type B type B type B type C type
Dimensions of JE Series Single Valve Unit (mm)
5-port, single solenoid
32
JE12□F5-PL
（300）
12
10
24
2
LED indicator
14
Manual override
PR
(Built-in muffler)
2-φ2.15 Counterbore φ3.2
Depth 1 (Mounting hole)
24.8
22.5
2-φ3.5
(Mounting hole)
80
5-M5×0.8
17.4
12
2
（B）
2.8
14
15.8
18.7
3（R2）
18.5
1（P）
11.6
4
（A）
For -75
φ8
24.5
11.6 11.6
5（R1）
2.2
2.2
9.4
18
5-port, single solenoid (with sub-base)
JE12□A5-25-PL
（300）
（49.7）
12
10
32
24
2
14
LED indicator
PR
(Built-in muffler)
24.8
22.5
Manual override
8.5
8.5
80
5-Rc1/8
5（R1）
35
For -75
40
1
（P）
31.7
47
4
（A）
23.5
1
6
3（R2）
7
φ16
15.2
2
（B）
17
18
4
（35.7）
9.1
2-φ4.5
(Mounting hole)
28
（29）
（57）
Options
（300）
LED indicator
14.3
5
2.3
25
12
●Lever type manual override: -84
2
（B）
24
LED indicator
2-φ3.5 (Mounting hole)
KEEP
ON
PUSH
27.5
5
LOCK
3.6
Code
A
B
JE12F5, JE12A5
80
85
JE12LF5, JE12LA5, JE12SF5, JE12SA5
−
85
Model
Remark
Overall length to the end of the valve
（300）
B
(Overall length of valve)
24.8
12
30
●S type plug connector: -PS
26
24
18.5
4-
R4
18
4
（A）
A
(Overall length of valve)
1.2
21.6
12.4
12
●Grommet: -GL
18.5
2-φ3.3
(Mounting hole)
2
（B）
●Locking type manual override: -81
22.5
●Mounting base: -22
(for side mounting)
24.8
●Mounting base: -21
mm
Dimensions of JE Series Single Valve Unit (mm)
5-port, double solenoid
JE12□F6-PL
32
（300）
12
10
24
LED indicator
14
Manual override
22.5
2
2-φ3.5
(Mounting hole)
2-φ2.15 Counterbore φ3.2
Depth 1 (Mounting hole)
24.8
2-PR
(Built-in muffler)
5-M5×0.8
17.4
111
11.6
49.7
49.5
2.8
14
46.8
2
（B）
55.5
3（R2）
12
1（P）
4
（A）
For -75
φ8
11.6 11.6
5（R1）
2.2
2.2
9.4
18
5-port, double solenoid (with sub-base)
JE12□A6-25-PL
（49.7）
（300）
9
32
12
10
24
2
2-φ4.5
(Mounting hole)
14
LED indicator
2-PR
(Built-in muffler)
8.5
24.8
22.5
Manual override
8.5
5-Rc1/8
5（R1）
For -75
40
1
（P）
23.5
47
35
31.7
111
4
（A）
6
3（R2）
32
4
17
18
（35.7）
28
（29）
（57）
7
φ16
15.2
2
（B）
Dimensions of JE Series Single Valve Unit (mm)
32
5-port, 3-position
12
10
24
2
LED indicator
14
Manual override
2-φ3.5
(Mounting hole)
2-φ2.15 Counterbore φ3.2
Depth 1 (Mounting hole)
24.8
2-PR
(Built-in muffler)
22.5
JE12□F7-PL
JE12□F8-PL
JE12□F9-PL
（300）
5-M5×0.8
2
（B）
2.8
14
5-port, 3-position (with sub-base)
JE12□A7-25-PL
JE12□A8-25-PL
JE12□A9-25-PL
（49.7）
2.2
2.2
9.4
18
（300）
55.8
58.7
58.5
64.5
3（R2）
17.4
11.6
120
12
1（P）
4
（A）
For -75
φ8
11.6 11.6
5（R1）
9
32
12
10
24
2
2-φ4.5
(Mounting hole)
14
LED indicator
2-PR
(Built-in muffler)
24.8
22.5
Manual override
8.5
8.5
5-Rc1/8
5（R1）
40
23.5
35
47
For -75
1
（P）
6
3（R2）
7
φ16
2
（B）
15.2
31.7
120
4
（A）
41
4
17
28
18
（35.7）
（29）
（57）
Options
●Locking type manual override: -81 ●Lever type manual override: -84
●Mounting base: -22
(for side mounting)
12.4
LED indicator
ON
PUSH
5
LOCK
25
3.6
A
(Overall length of valve)
KEEP
22.5
18.5
2.3
4
（A）
12
（300）
24.8
12
21.6
14.3
24.8
2-φ3.3
(Mounting hole)
●Grommet: -GL
●S type plug connector: -PS
26
mm
Code
A
B
JE12F7〜JE12F9, JE12A7〜JE12A9
120 130
−
121
−
130
JE12SF7〜JE12SF9, JE12SA7〜JE12SA9
Remark
111 121
JE12LF6, JE12LA6, JE12SF6, JE12SA6
JE12LF7〜JE12LF9, JE12LA7〜JE12LA9
LED indicator
Overall length to the opposite
end of the solenoid
27.5
Model
JE12F6, JE12A6
24
（300）
B
(Overall length of valve)
2
（B）
Dimensions of JE Series Manifold (mm)
Manifold for combination mounting of 2, 3, 5-port valves
JEM□F
(Direct piping type)
（48.2）
32
PR
(Built-in muffler)
24
（300）
L
LED indicator
15
Manual override
12.5 (Pitch)
9
4-φ4.5
(Mounting hole)
12
1
（P）
2
（B）
2
（B）
2
（B）
2
（B）
3
（R2）
3
（R2）
120
5
（R1）
4
（A）
17
4
（A）
46
4
（A）
1
（P）
1.5
32.5
2.2
2.2
41.5
8.5
4
（A）
14.5
11.6
5
（R1）
17.2
16.5
23
111
16.5
80
24.8
6-Rc1/8 (both sides)
〔Installation example〕
2.2
M5×0.8
4
2.2
P
（4）
15.5
18
stn.1 stn.2 stn.3 stn.4 stn.5 stn.6
（34.2）
JEM6F
stn.1 JE12F3-PL-D4
stn.2 JE12F4-PL-D4
stn.3 JE12F5-PL-D4
stn.4 JE12F6-PL-D4
stn.5 JE12F7-PL-D4
stn.6 JEBP
Unit dimensions
Number
of units
2
L
P
42.5
34.5
3
55.0
47.0
4
67.5
59.5
5
80.0
72.0
6
92.5
84.5
7
105.0
97.0
8
117.5
109.5
9
130.0
122.0
10
142.5
134.5
11
155.0
147.0
12
167.5
159.5
13
180.0
172.0
14
192.5
184.5
15
205.0
197.0
16
217.5
209.5
17
230.0
222.0
18
242.5
234.5
19
255.0
247.0
20
267.5
259.5
Dimensions of JE Series Manifold (mm)
Manifold for combination mounting of 2, 3, 5-port valves
JEM□A
(Base piping type)
（300）
（64.2）
PR
(Built-in muffler)
L
LED indicator
32
16
Manual override
24
10
12.5 (Pitch)
2-φ4.5
(Mounting hole)
12
49
21.5
120
111
24.5
36.5
27.5
14
3.5
3
（R2）
13.5
42.1
5
（R1）
1
（P）
29.5
80
83.5
24.8
6-Rc1/8 (both sides)
〔Installation example〕
JEM6A
stn.1 JE12A3-PL-D4
stn.2 JE12A4-PL-D4
stn.3 JE12A5-PL-D4
stn.4 JE12A6-PL-D4
stn.5 JE12A7-PL-D4
stn.6 JEBP
5
P
（5）
stn.1 stn.2 stn.3 stn.4 stn.5 stn.6
2
（B）
12.5
31.5
（50.2）
18
Plug 2(B) when mounting JE12※A1,※A3
9
4
（A）
Plug 4(A) when mounting JE12※A2,※A4
2-Rc1/8 (per each station)
●DIN rail mounting bracket (-DN)
（7.3）
2
Unit dimensions
21
（8.7）
3
（R2）
（48.6）
5
（R1）
1
（P）
Number
of units
2
L
P
44.5
34.5
3
57.0
47.0
4
69.5
59.5
5
82.0
72.0
6
94.5
84.5
7
107.0
97.0
8
119.5
109.5
9
132.0
122.0
10
144.5
134.5
11
157.0
147.0
12
169.5
159.5
13
182.0
172.0
14
194.5
184.5
15
207.0
197.0
16
219.5
209.5
17
232.0
222.0
18
244.5
234.5
19
257.0
247.0
20
269.5
259.5
260
">