Koganei PA Solenoid valve Instruction manual

BK-UV002 Ver.1.0
Air Valve
SOLENOID VALVES PA PB SERIES
INSTRUCTION MANUAL Ver.1.0
Handling Instructions and Precautions
Solenoid
Internal circuit
Method for Switching from Double to Single
● DC24V
●For the PA series
●For the PB series
Rotate the end covers on the PA□ F6 and PA
□ A6 models (2-position double solenoid
valves) 180 degrees to use them as single
solenoid valves (this change is not possible on
3-position valves). Note that the PA□ F5 and
PA□ A5 models (2-position single solenoid
valves) are designed specifically for use as
single solenoid valves, and cannot be used as
double solenoid valves.
Change the switching pin on the PB□ C6
model (2-position double solenoid valve) to
use as a single solenoid valve (this change is
not possible on the 3-position valve).
Note that the PB□ C5 model (2-position single
solenoid valve) is designed specifically for use
as a single solenoid valve, and cannot be
used as a double solenoid valve.
●Single solenoid
(Connector interior)
Color of lead wire: Black 14
（SA）
Color of lead wire: Red COM
14
（SA）
（Red）
●Double solenoid
(Connector interior)
Color of lead wire: Black 14
（SA）
14
（SA）
（Red）
Color of lead wire: Red COM
（Green）
12
（SB）
Color of lead wire: White 12
（SB）
Note:Since there is no polarity, the valve can be
used for either ＋COM or −COM.
Switching from double solenoid valves
(at shipping) to single solenoid valves
As shown in the illustration below, a D
marked on the end cover on the model label
surface side means that the unit is set for a
double solenoid function. To convert to the
single solenoid valve function, use a Phillips
screwdriver to remove the end cover, rotate it
180 degrees, and set the mark to S. The
recommended tightening torque for the end
cover mounting screw is as shown below.
● AC100V, 200V
(Connector interior)
Color of lead wire: Black 14
（SA）
Color of lead wire: Red COM
As shown in the illustration below, use a
Phillips screwdriver to remove the female
thread block or plate of the unit’s front surface
output port 4(A) and 2(B), then remove the
end cover, remove the switching pin from the
lower level hole and insert it in the upper level
hole, to convert to the single solenoid function.
The recommended mounting screw tightening
torque for the end cover and the female thread
block or plate are as shown below.
Switching pin insert
for double solenoid
Model label
●Single solenoid
Switching from double solenoid valves
(at shipping) to single solenoid valves
Switching pin insert
for single solenoid
Switching
pin
14
（SA）
（Red）
●Double solenoid
(Connector interior)
Color of lead wire: Black 14
（SA）
14
（SA）
（Red）
End cover
Mounting screw
Color of lead wire: Red COM
End cover
qEnd cover mounting screw
（Green）
12
（SB）
Female thread block (plate)
wMounting screw
Color of lead wire: White 12
（SB）
Cautions: 1. Do not apply megger between the
pins.
2. Leakage current inside the circuit
could result in failure of the solenoid
valve to return, or in other erratic
operation. Always use it within the
range of the allowable leakage current
in electrical specifications listed on
p.671, 685. If circuit conditions, etc.
cause the current leakage to exceed
the allowable leakage current, consult
us.
3. For double solenoid valves,
avoid energizing both solenoids
simultaneously.
End cover rotated
180 degrees
D
Double solenoid condition
S
Single solenoid condition
Recommended tightening torque for mounting
screws: 88.3N･cm {9.0kgf･cm} [7.8in･lbf]
Cautions: 1. Do not remove the end cover except
when switching between single and
double solenoids.
2. When mounting the end cover,
confirm that the gasket is attached
before proceeding with the mounting.
Recommended tightening torques for mounting
screws
q End cover mounting screw : 39.2N･cm {4.0kgf･cm}
[3.5in･lbf]
w Mounting screw
: 137.3N･cm {14.0kgf･cm}
[12.2in･lbf]
Cautions: 1. Do not remove the end cover except
when switching between the single
and double solenoids.
2. When mounting the end cover and the
female thread block or plate, confirm
that the gasket is attached before
proceeding with the mounting.
DIN Connector
Pilot air switching method (PB series only)
Change the switching pins on the PB□ G and
PB□ V models (external pilot positive pressure
valves and vacuum valves) to use as an internal
pilot positive pressure valve. Note that the PB□
model (internal pilot valve) is for internal pilot use
only, and cannot be used as an external pilot
positive pressure or vacuum valve.
Switching from double solenoid valves
(at shipping) to single solenoid valves
As shown in the illustration below, use a Phillips
screwdriver to remove the female thread block or
plate of the unit’s top surface side outlet port 4(A)
and 2(B), and then remove the switching pin
from its position (lower level) for the external pilot
specification and insert it in the position (upper
level) for the internal pilot specification, to
convert to the internal pilot specification. The
recommended mounting screw tightening torque
for the female thread block or plate is as shown
below.
Plate or female thread block
Mounting screw
Wiring instructions
●Installation
Confirm the installation of the pilot valve
gasket, and then firmly tighten the mounting
screws to the recommended torque below.
Lastly, firmly close the solenoid cover.
Recommended tightening torque for
mounting screws: 14.7N･cm {1.5kgf･cm}
[1.3in･lbf]
Manual override
●Manual override (for both locking and
non-locking types)
To lock the manual override, use a small
screwdriver to open the manual override
cover. In that position, press it all the way
down and turn it 90 degrees in the clockwise
direction to lock. When in the lock position,
turning the manual override 90 degrees in the
counterclockwise direction releases a spring
on the manual override, returns it to the
normal position, and releases the lock. When
the manual override is not turned, this type
acts just like the non-locking type.
Pilot switching pin
Manual override
cover
12
B
14
A
Manual
override
14 (SA) side
Switching pin insert
for external pilot
Terminal cover
Terminal body
Screwdriver
(blade width of
about 4mm
[0.16in.])
Cover mounting screw Note
Note: The appropriate tightening torque for the cover
mounting screw is 29.4N･cm {3kgf･cm}
[2.6in･lbf ].
Cable
(Outer diameter 4〜7mm
[0.16〜0.27in.])
Cable gland
Screwdriver
(blade width
of about 3mm
[0.12in.])
Terminal w
Terminal
body
Terminal e
Washer
PUSH
Switching pin insert
for internal pilot
Remove the cover mounting screw and lift the
terminal cover off from the solenoid valve.
Use a screwdriver, etc. to press hard against
the head of the terminal body from the
mounting hole of the terminal cover, and
remove the terminal body.
Pass a cable gland, washer, and cable gasket
over the cable, insert it via the wiring outlet of
the terminal cover, and connect lead wires to
the terminal body (screwdriver blade width of
about 3mm [0.12in.]).
Cable gasket
TURN
Manual override
12 (SB) side
Terminal q
Terminal cover
Lead wire
Override operation portion
Inner diameterφ3.5 [0.138in.]
Depth 8 [0.31in.]
Terminal e
Terminal q
Recommended tightening torque for
mounting screws: 137.3N･cm {14.0kgf･cm}
[12.2in･lbf]
〈 Terminal internal wiring connections〉
〉
Caution: When mounting the female thread block or
plate, confirm that the gasket is attached
before proceeding with the mounting.
Pilot valve replacement
●Removal
Hand-open the solenoid cover at q and use a
small screwdriver to remove the mounting
screws w mounting the pilot valve in place.
Use pliers to hold and pull out the pilot valve’s
flange e, and then remove the pilot valve.
w Mounting screw
e
Terminal w
Terminal body
(solenoid side)
Solenoid cover
Pilot valve
14 (SA) side
LED:Red
q
Pilot valve
12 (SB) side
LED: Green
Caution: The maximum height of the cover when
open is 48mm [1.89in.] from the top
surface. Ensure enough space for
maintenance, etc.
Cautions: 1. The PA/PB series valves are pilot type
solenoid valves. As a result, the
manual override cannot switch the
main valve without air supplied from
the 1(P) or X(P2) port.
2. Always release the lock of the manual
overrides before commencing normal
operation.
3. Do not attempt to operate the manual
override with a pin or other object
having an extremely fine tip. It could
damage the manual override button.
4. Caution should be exercised to avoid
rotating the manual override too far. It
could damage the button.
5. If operating the solenoid valve’s
manual override for maintenance, etc.,
check before restarting operations that
the solenoid valve’s manual override
has returned to the normal position,
and that the main valve is in the
required position for switching.
6. The maximum height of the cover
when open is 8.4mm [0.331in.] from
the top surface of the cover.
Terminal No.
Internal wiring connections
q
SOL.14 (SA) side
w
SOL.12 (SB) side
e
COM.
Ground
Caution: Because the cable has no polarity, it can
be used for either ＋COM or −COM.
Handling Instructions and Precautions
Manifold
Valve mounting and removal
Port isolator (PB series settings only)
●For PA series
Installation of a port isolator at port 1(P)
between the stations of a split-type manifold
isolates the air path between the station where
the port isolator is installed and a station with a
smaller stn. No.
●Port isolator for port 1(P) (Type: PB-SP)
Can supply 2 different types of pressure.
2. Installation using a bottom-surface nut
qInsert a hexagon nut into the manifold’s T
groove.
wUse a screw to tighten from the bottom of the
mounting plate. Ensure that a suitable length
screw is used, and mount it with particular
attention for the tightening torque. In addition,
use a washer if necessary to prevent looseness.
9 or less
When removing the valve body from a sub-base or
manifold, loosen the valve mounting screws (2
places), and lift in the direction of the arrow (see
illustration below). To mount, follow the above
procedure in reverse. The recommended tightening
torque for the valve mounting screws is as shown
below.
Port isolator for
port 1(P)
PB-SP
Gasket
PA-GS1
Caution: For later installing of other port isolators,
the manifold must be disassembled and
then reassembled. See the disassembly
diagram on p.669.
Nameplate
Recommended tightening torque for mounting screws:
176.5N・cm {18.0kgf・cm} [15.6in・lbf]
●For PB series
When removing the valve, use a hexagonal bar
wrench to loosen the valve mounting screws A and
B by 2〜4 rotations. Move the mounting screw B
(which includes screws on both sides, and a tie rod)
in the direction of the arrow, move the valve until a
gap of about 1mm opens up on each side of the
valve, and then lift the valve in the direction of the
large arrow. Be careful when loosening the
mounting screws A and B, since the valve could fall
at that time, for example, in an upside down
manifold mounting. To assemble, follow the above
procedure in reverse. The recommended tightening
torque for the valve mounting screws is shown
below.
The nameplate is attached to the other side from
that of the female thread block. For attaching or
removing, flex it so that it fits the grooves on the
upper and lower side of the plate, as shown in the
illustration.
Since the nameplate can be attached to either the
top surface or front surface, make a careful
selection to conform with the valve piping
specifications that require combinations on the front
and top surface piping.
qHexagon nut (M5×0.8)
Nut thickness 5mm or less
wScrew (M5×0.8)
29.5
26
3. Installation using a DIN rail
Insert into the grooves in the sequence of q and w
below.
Push in the direction of e, and align with the center of
the DIN rail.
rInsert a hexagon nut into the manifold’s T groove.
tUse a screw to tighten from the top of the manifold.
Always use a steel DIN rail. Do not use an aluminum
rail, as it would not be sufficiently strong, causing
deflection to loose products or dents in the rail that
could lead to defects.
Ensure that a suitable length screw is used, and mount
it with particular attention for the tightening torque. In
addition, use a double nut, etc., on the top surface of
the manifold if necessary for the prevention of
looseness.
w
Nameplate
q
Plate
e
tScrew (M5×0.8)
29.5
26
21 or more
Female thread
block
Manifold installation methods
Mounting screw B
1. Installation using a top-surface bolt
Use a bolt to tighten from the top of the manifold.
Care must be exercised when mounting to use a
sufficiently long screw, and mount it with
particular attention for the tightening torque. In
addition, use a washer if necessary to prevent
looseness.
Screw (M5×0.8)
Recommended tightening torque for mounting screws:
411.9N・cm {42.0kgf・cm} [36.5in・lbf]
26
29.5
42.5
Recommended tightening torque for mounting screws:
284.4N・cm {29.0kgf・cm} [25.2in・lbf]
●Precaution for installation of PA series
manifolds (PAM□F, PAM□A, PAM□B)
While the manifold has an M3 groove, be
aware that this groove is not for use in
manifold installation. Use this groove when
binding lead wires, as a space for securing
bands of binding wires.
1.5
24
Caution: Although the flow path for the PA and PB double
solenoid specifications (F6, A6, C6) is set to the
1(P)→ 2(B) at shipping from the factory,
conditions during shipping could cause the stem
to move and the position to shift. When applying
air to the system for the first time, confirm that it
is safely set by running a preliminary check on
switching, using electricity or manually. Beware
that air could suddenly blow out from the OUT
port.
Nut thickness 4mm or less
DIN rail (steel)
3.3
Mounting
screw A
rHexagon nut (M5×0.8)
5
3
5.6
●Installing the PA series F type manifold
(PAM□F)
Dimensions of M3 nut groove
(cannot be used for securing the manifold in place)
Safe block
Piping
Individual air supply and exhaust spacer
(Available in PB series only)
Use an individual air supply and exhaust spacer
when individually supplying and exhausting air for a
certain 1 station on the same manifold. Installation
of the individual air supply and exhaust spacer
allows control from the spacer installation position
of the air supply and exhaust to the next smaller
stn. number valve. Note that a dedicated valve
(PB24□Z-□-Z) is required when using this spacer,
and take particular caution on product selection.
When used in combination with a 3-position exhaust
center valve on the same manifold, the safe block can
ensure cylinder intermediate stop and hold its position for
long periods without being affected by air leaks between
the spool and valve body. In addition, when used in
combination with a 2-position valve, the safe block can be
used to prevent falls at the end of cylinder stroke when
residual pressure on the supply side is exhausted.
Wiring
D-sub connector
The D-sub connector can change the wiring outlet
orientation between the top surface and side surface.
During cylinder operation
4（A）
Cylinder pressure
（P2）
2（B）
Insert from the back
〈Top surface outlet〉
〈Side surface outlet〉
4（A）
2（B）
Air supply pressure（P1）
During check valve operation
4（A）
2（B）
Individual air supply and
exhaust side spacer
●Port position for air supply and
exhaust (individual air supply and
exhaust spacer)
1. For front surface piping
3, 5（R）
Exhaust port
Cable specification
2（B）
Cautions: 1. Set the cylinder load so that the pressure on the
cylinder side 2(B) and 4(A) ports is less than
double the supply side pressure and also does not
exceed the allowable pressure range.
2. When exhausting residual pressure on the cylinder
side, use a small screwdriver, etc., to push the
residual pressure exhaust manual override, as
shown in the diagram below. Caution should be
exercised to guard against the possibility of
workpieces falling or moving when the residual
pressure is exhausted.
3. When a safe block is used in combination with a 3position closed center valve or pressure center
valve, it does not ensure a cylinder’s intermediate
stop and position holding, but prevents workpieces
from falling.
For top surface piping
2. For top surface piping
3, 5（R）
Exhaust port
4（A）
Air supply pressure（P1）
For front surface piping
In the case of cable specification, the shape of the
cable ends is shown in the diagram below.
φ3.9 [0.154in.]
Red: COM
Station No.
Cable 3-leads of AWG24
White: 12 (SB) side solenoid
(cannot be used with single solenoids)
Black: 14 (SA) side solenoid
Because the cable has no polarity, it can be
used for either ＋COM or −COM.
Residual pressure exhaust manual override
1（P）
Air supply port
1. Single solenoid (C5 type)
Connection polarity
Positive Negative
common common
12
P2
4A
P
1
R2
3
2B
4A
2B
5
R1
1
P
Safe block
Color of
lead wire
−
＋
Black
＋
−
Red
Circuit diagram
SA
COM
Internal
circuit
1（P）
Air supply port
Recommended tightening torque for mounting
screws: 58.8N・cm {6.0kgf・cm} [5.2in・lbf]
Safe block
Residual pressure exhaust manual override
2. Double solenoid (C6,C7,C8,C9 type)
4. To lock the residual pressure exhaust manual
override, push the manual override all the way
down and rotate it 90 degrees in the clockwise
direction. When in the locked state, rotate the
manual override 90 degrees in the counterclockwise direction; a spring returns the manual
override to its normal position, and the lock is
released. When the manual override is not turned,
this type acts just like the non-locking type.
5. Always release the lock of the manual override
before commencing normal operation.
6. Do not attempt to operate the manual override with
a pin or other object having an extremely fine tip. It
could damage the manual override button.
7. Caution should be exercised to avoid rotating the
manual override too far. It could damage the
button.
8. When the residual pressure exhaust manual
override is operated for maintenance, etc., ensure
that the manual override has returned to its normal
position before restarting operations.
Connection polarity
Positive Negative
common common
Color of
lead wire
−
＋
Black
＋
−
Red
−
＋
White
Circuit diagram
SA
COM
SB
Internal circuit
PB24□Z-□-Z
Dedicated valve
Cylinder pressure
（P2）
Pin No. (Terminal No.) and Corresponding Solenoids (for plug-in type)
The examples below are for reference in showing the relationships between the pin No. (terminal No.) and the corresponding solenoids
for the plug-in type manifold. All the examples of show cases in which maximum controlled solenoids are used.
●D-sub connector (25 pins)
［Wiring specification D-sub connector (maximum number of control pins: 20)］
Example 1
PBM12P-DUL
stn. 1
2
3
4
5
6
stn.1〜4 PB24C5-T2-B-D4
stn.5〜11 PB24C6-T2-B-D4
stn.12 PB-BPMD
7
8
9
（Top View）
1
2
3
4
5
6
7
8
9
10 11 12 13
14 15 16 17 18 19 20 21 22 23 24 25
10 11 12
Number of unit: 12
Single solenoid
Example 2
Double solenoid
PBM10P-DUL
stn. 1
2
3
4
5
6
Wiring specification: -DUL
Pin no.
Wiring connection specification:
Blank (packed wiring)
Valve no. 1A 2A 3A 4A 5A 5B 6A 6B 7A 7B
8
9
2
3
4
5
6
7
8
9 10 11 12 13
Pin no.
14 15 16 17 18 19 20 21 22 23 24 25
Valve no.
8A 8B 9A 9B 10A 10B 11A 11B 12A 12B COM COM
Block-off plate
stn.1〜4 PB24C5-T2-B-D-D4
stn.5〜9 PB24C6-T2-B-D4
stn.10 PB-BPMD
7
1
（Top View）
1
2
3
4
5
6
7
8
9
10 11 12 13
14 15 16 17 18 19 20 21 22 23 24 25
10
Number of unit: 10
Single solenoid
Wiring specification: -DUL
Pin no.
Wiring connection specification:
When all single solenoids are
specified as -D (double wiring)
Valve no. 1A 1B 2A 2B 3A 3B 4A 4B 5A 5B
1
2
3
4
5
6
7
8
9 10 11 12 13
Pin no.
14 15 16 17 18 19 20 21 22 23 24 25
Valve no.
6A 6B 7A 7B 8A 8B 9A 9B 10A 10B COM COM
Double solenoid
Block-off plate
●Terminal block box (21 terminals with M3 screw)
［Wiring specification terminal block box (maximum number of control pins: 20)］
Example 1
PBM13P-TL
stn. 1
2
3
4
stn.1〜6 PB24C5-T2-B-D4
stn.7〜12 PB24C6-T2-B-D4
stn.13 PB-BPMD
5
6
7
8
9
（Top View）
3
1
10 11 12 13
5
4
2
7
6
9
8
11
13
15
17
19 COM
10
12
14
16
18
20
5
7
9
11 13 15 17 19 COM
Number of unit: 13
Wiring specification: -TL
Wiring connection specification:
Blank (packed wiring)
Single solenoid
Pin no.
1
Valve no.
1A 3A 5A 7A 8A 9A 10A 11A 12A 13A COM
3
Pin no.
2
4
6
8
10 12 14 16 18 20
Valve no.
2A 4A 6A 7B 8B 9B 10B 11B 12B 13B
Double solenoid
Block-off plate
Example 2
PBM10P-TL
stn. 1
2
3
4
stn.1〜6 PB24C5-T2-B-D-D4
stn.7〜9 PB24C6-T2-B-D4
stn.10 PB-BPMD
5
6
7
8
9
（Top View）
3
1
2
10
5
4
7
6
9
8
11
13
15
17
19 COM
10
12
14
16
18
20
5
7
9
11 13 15 17 19 COM
Number of unit: 10
Wiring specification: -TL
Wiring connection specification:
When all single solenoids are
specified as -D (double wiring)
Single solenoid
Pin no.
1
Valve no.
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
3
Pin no.
2
Valve no.
1B 2B 3B 4B 5B 6B 7B 8B 9B 10B
4
6
8
10 12 14 16 18 20
Block-off plate
Double solenoid
Notes: 1. The valve No.1A, 1B, 2A, 2B… numerals show the stn. numbers in order, while the letters A and B show the A and B sides of the solenoid.
2. The stn. numbers are counted from the left, 1, 2…, with the solenoid on top and the valve in front.
3. When selecting the wiring connection specification -D for the single solenoid, the wiring base side of the specified station becomes a double solenoid wiring connection.
Serial Transmission Manifold, Specifications
General Specifications
Voltage
DC24V ±10%
Operating temperature range
5〜50°C [41〜122°F]
Vibration resistance
49.0m/s2 {5.0G} (Conforms to JIS C 0911)
Shock resistance
98.1m/s2 {10.0G} (Conforms to JIS C0912)
●For details of specifications, see the user’s manuals (see below).
Serial Transmission Block, Terminal Block (LED) Names
●For UNI-WIRE® System
●For Mitsubishi Electric MELSECNET/MINI-S3
●For OMRON SYSBUS Wire System
Transmission block specification: -01 (16 outputs), -02 (8 outputs)
Transmission block specification: -11
Transmission block specification: -21
7 8
5 6
24V
0V
4
5
6
7
D
8
G
SD
24V
0V
RDA
RD
4
G
3
1
2
3
4
5
6
0 1 E
5 6
D
2
9
OFF
RDB
4
3
2 3
0 1 E
2 3
9
7 8
×10
3
ON
1
T/R
RUN ERR
ADDRESS
×1
PWR RUN ERR
POWER SEND
Dip switch for various settings
Rotary switch for station setting
OFF
ON
ON
SDA
O
N
Address setting switch
SDB
TERM
SG
FG
24V
＋
0V
E.C. MODE switch
LED indicator
LED indicator
Description
Indicator
Description
PWR
•Lights up when power is turned on
POWER
•Lights up when power is turned on
•Flashes during voltage drops or
when over current (a short circuit)
RUN
•Lights up for normal data communication with master station
SD
•Flashes during sending data
•Flashes during normal transmission
•Lights up or shuts off during faulty transmission
Remarks
※The UNI-WIRE® System is a serial parallel transmission
system developed jointly by NKE and KURODA
PRECISION INDUSTRIES. For details of the UNIWIRE System, see the NKE or KURODA PRECISION
INDUSTRIES catalog, user’s manual, etc.
● Number of outputs per block
16 solenoids (transmission block specification: -01)
8 solenoids (transmission block specification: -02)
● Related materials: User’s manual, document No.
HV017
FG
24V
0V
End station setting switch
LED indicator
Indicator
SEND
−
RD
•Flashes during receiving data
ERR
•Lights up when data receiving error occurs,
shuts off for normal communication
Indicator
Description
• Lights up when transmission is normal, and the PC
RUN
is in operations mode or monitor mode
•Flashes during normal transmission
•Lights up during standby or faulty transmission
•Shuts off during faults (during watchdog timer fault)
T／R
ERR
Remarks
● Master station unit: SYSMAC-C (CV) series
Remarks
● Master station: MELSEC-A series
AJ71PT32-S3, AJ71T32-S3, A2CCPU/A2CJCPU,
A1SJ71PT32-S3, link sub-stations up to a maximum of 64
stations, and link I/O numbers up to a maximum of 512.
※For details, see the Mitsubishi Electric’s sequencer
MELSEC-A series catalog, user’s manual, etc.
● Number of outputs per block
Maximum of 16 solenoids
※Since the block is equivalent to 2 stations, if substations are entirely composed of the blocks, the
maximum becomes 32 units.
C200H-RM201, C500-RM201
※For details, see the OMRON’s programmable controller
SYSMAC C(CV) series catalog, user’s manual, etc.
● Number of outputs per block
Maximum of 16 solenoids
● Related materials: User’s manual, document No.
HV019
● Related materials: User’s manual, document No.
HV018
●For OMRON B7A Link Terminal
●For KOYO ELECTRONICS INDUSTRIES SA Bus
Transmission block specification: -31 (standard type), -32 (high speed type) Transmission block specification: -41 (16 outputs), -42 (8 outputs)
Output selector switch for faults
Transmission block specification: -51 (16 outputs), -52 (8 outputs)
Switch for address setting and output
processing setting during error occurrence
Station setting switch
1 2 3 4 5 6 7 8
POWER ERROR
ON
PWR ERR
LOAD
OFF
●For SUNX S-LINK
POWER SEND
ON
HOLD
1
24V
ERR
SIG
L+
0V
L-
SHLD
LED indicator
LED indicator
G
L24V
D
0V
2
3
24V
4
5
6
G
7
8
D
0V
24V
LED indicator
Indicator
Description
Indicator
Description
Indicator
Description
PWR
•Lights up when power is turned on
POWER
•Lights up when power is turned on
POWER
•Lights up when power is turned on
ERR
•Lights up during faulty transmission
ERROR
•Lights up during faulty transmission or other faults
SEND
•Flashes during normal transmission
•Lights up or shuts off during faulty transmission
Remarks
Remarks
● Connection method: 1 to 1
※For details of the SA Bus system, see the KOYO
ELECTRONICS INDUSTRIES catalog, user’s
manual, etc.
Remarks
● Number of outputs per block
● Number of outputs per block
(Transmission block spec.) Standard type (-31) High speed type (-32)
Transmission delay time
Max.31ms
Max.5ms
Transmission distance
Max.500m
Max.100m
※For details of the B7A Link Terminal, see the
OMRON catalog, user’s manual, etc.
● Number of outputs per block
Maximum of 16 solenoids
● Error output specifications
Output mode: NPN open collector
Rated load voltage: DC24V
Output current: Sink current MAX. 40mA
● Related materials: User’s manual, document No.
HV020
※For details of the S-LINK System, see the SUNX
catalog, user’s manual, etc.
16 solenoids (transmission block specification: -41)
8 solenoids (transmission block specification: -42)
16 solenoids (transmission block specification: -51)
8 solenoids (transmission block specification: -52)
● Related materials: User’s manual, document No.
● Related materials: User’s manual, document No.
HV021
HV022
●For Mitsubishi Electric MELSEC I/O LINK
Transmission block specification: -61
●For Fuji Electric FA Components
& Systems T Link Mini
●For KEYENCE KZ-R
Transmission block specification: -81
Transmission block specification: -71
24V
0V
POWER/ERROR
3
S2
SD
FG
24V
0V
S＋
LED indicator
RUN
7 8 9A
Description
Indicator
Description
PW
•Lights up when power is turned on
•Lights up when receiving data transmitted
from master unit is normal
PWR
•Lights up when power is turned on
ALM
•Lights up during faulty transmission
SD
•Lights up during sending data to master unit
RD
•Lights up during receiving data from master unit
ERR.
•Lights up when faulty data transmitted from master unit
● 16 remote I/O unit connection stations, for a maximum
of 128 inputs/outputs
※For details, see Mitsubishi Electric’s sequencer catalog,
user’s manual, etc.
24V
0V
Error retention switch
Indicator
Description
POWER/
ERROR
•Green: Lights up for normal
communications state
•Orange: Lights up when communications state is poor
(can also light up when
address settings are
incorrect)
•Red:
Lights up during faulty
operation, or when
transmission is cut off
Remarks
※For details of the T Link Mini, see the Fuji Electric
FA Components & Systems catalog, user ’s
manual, etc.
● Number of outputs per block
Remarks
FG
LED indicator
Indicator
RUN
0 1 E
S−
ON/OFF switch for terminal resistance
LED indicator
9
ERROR MODE
HOLD
CLEAR
OFF
S1
ADDRESS
0 1 E
7 8
7 8
5 6
FG
4
DG
9
2 3
ON
RD
3
7 8
0 1 E
2 3
BCDE
9
2 3
DATA
3
3456
SD
PWR ALM
E
2
F01
5 6
3
4
ST. NO.
RUN ERR.
Address setting switch
5 6
PW
Station setting switch
ADDRESS
×10
×1
4
Station setting switch
Maximum of 16 solenoids
● Related materials: User’s manual, document No.
HV024
Remarks
※For details of the KZ-R, see the KEYENCE
catalog, user’s manual, etc.
● Number of outputs per block
Maximum of 16 solenoids
※Since the block is equivalent to 4 stations, if substations are entirely composed of the blocks, a
maximum of 4 units can be connected to 1 master unit.
● Number of outputs per block
Maximum of 16 solenoids
● Related materials: User’s manual, document No.
HV025
● Related materials: User’s manual, document No.
HV023
●For OMRON CompoBus/S
●For Mitsubishi Electric CC-Link
●For OPCN-1 (former JPCN-1)
Transmission block specification: -A1 (16 outputs), -A2 (8 outputs)
Transmission block specification: -B1
Transmission block specification: -C1
3
O
N
6
8
4
6
8
8
4
4
6
1
2
3
4
5
6
2
SD
CLEAR
2
2
HOLD
＋24C ＋24V
BDL
BS−
24G
FG
＋24V （FG）
SLD
DG
DB
Indicator
PWR
COMM
ERR
State
Lights up
Shuts off
Lights up
Shuts off
Lights up
Shuts off
Indicator
Description
•During power supply
PW
•Lights up when power is turned on
Green
•Power not supplied
L RUN
•Lights up when normal data is received
from master station
Yellow
Red
Description
•During normal communication
•Communication fault, or standby
SD
•Lights up during sending data
•Communication fault occurred
RD
•Lights up during receiving data
•During normal communication, or standby
Remarks
※For details about CompoBus/S, see the Omron catalog,
user’s manual, etc.
● Number of outputs per block
16 solenoids (transmission block specification: -A1)
8 solenoids (transmission block specification: -A2)
● Related materials: User’s manual, document No.
HV026
L ERR.
•Lights up during transmission errors, and
shuts off when time is over
Lights up during station number setting error
or transmission speed setting error
Remarks
※For details of the CC-Link, see the Mitsubishi Electric
catalog, user’s manual, etc.
● Number of outputs per block
16 solenoids (transmission block specification: -B1)
※Since the block occupies 1 station, if the block is
entirely composed of remote I/O stations, a maximum
of 64 units can connect to 1 master station.
● Related materials: User’s manual, document No.
HV027
F01
E
2
1
H
L
ON
0V
FG
SG
ALRM
OFF
＋24V
0C
B
A
Switch for setting terminal resistance (TERM)
LED indicator
LED indicator
Color
3
DA
HOLD/CLEAR switch
LED indicator
E
RD
＋24C
BS＋ BDH
F01
3456
0
3456
0
2
×10
0
2
STATION NO.
×1
PW L RUN L ERR.
BCDE
B RATE
PWR COMM ERR
Station setting switch(STN) Transmission speed setting switch (RATE)
Fuse
PWR COMM
BCDE
Station setting switch
7 8 9A
Transmission speed setting switch
7 8 9A
Dip switch for various settings
Indicator
PWR
COMM
ALRM
State
Lights up
Shuts off
Lights up
Shuts off
Lights up
Shuts off
Color
Green
Green
Red
Description
•Normal power
•Abnormal power
•Normal communications
•Communication fault
•Communication fault or setting fault
•Normal
Remarks
※For details of the OPCN-1, see JIS3511: 1999 (JEMF3008: 1999) Programmable Controller Field Network
Standard (level 1).
● Specifications
Compatibility class: TYPE-S52U
Communication function: Initial setting service, input/output
service, reset service
Transmission speed (transmission distance is a reference value):
125kbps (1km), 250kbps (800m),
500kbps (480m), 1Mbps (240m)
Number of outputs:
16 points/1 unit
Station setting: 01H〜7FH (Number of connecting stations can reach to a
maximum of 31 slave units for 1 master station)
● Related materials: User’s manual, document No.
HV028
■ For specifications and handling details, see the above-listed user’s manuals (document Nos. HV017〜HV029).
Solenoid Valves PB Series Disassembly Diagram
●Non-plug-in type
End block (right side)
Gasket
Connection rod for addition
Gasket
Connection rod
End block (left side)
Mounting screw
411.9N･cm {42.0kgf･cm} [36.5in･lbf ]
※Wiring-related parts are omitted.
●Plug-in type
Serial transmission block
Cover mounting screw
58.8N･cm {6.0kgf･cm} [5.2in･lbf]
Gasket
(for IP65 or equivalent)
Terminal block box
Wiring base assembly
Gasket
(for IP65 or equivalent)
End block (right side)
Gasket
Connection rod for addition
Gasket
Connection rod
End block (left side)
Mounting screw
411.9N･cm {42.0kgf･cm} [36.5in･lbf]
D-sub connector
Wiring block mounting screw
78.5N･cm {8.0kgf･cm} [6.9in･lbf]
※Wiring-related parts are omitted.
SOLENOID VALVES
SERIES
Specifications
Basic Models and Valve Functions
Basic model
Item
For direct piping, F type Manifold
PA24□F5
PA24□F6
PA24□F7, PA24□F8, PA24□F9
For sub-base piping
For A type and B type Manifolds
PA24□A5
PA24□A6
PA24□A7, PA24□A8, PA24□A9
Number of positions
3 positions
2 positions
Number of ports
5
Double solenoid Note
Single solenoid
Valve function
Closed center, Exhaust center, Pressure center
Remark: For the specifications and order codes, see p.675〜677.
Note: 2-position double solenoid valve can be switched to a single solenoid valve. For details, see p.665.
Specifications
For direct piping
Basic model For F type Manifold
Item
PA24□F5
PA24□F6
For sub-base piping
PA24□A5
For A type and B type Manifolds
PA24□A6
Media
PA24□F7
PA24□F7G
PA24□F8 PA24□F5G PA24□F6G PA24□F8G PA24□F5V PA24□F6V PA24□F7V
PA24□F9
PA24□F9G
PA24□A7
PA24□A7G
PA24□A8 PA24□A5G PA24□A6G PA24□A8G PA24□A5V PA24□A6V PA24□A7V
PA24□A9
PA24□A9G
Air
External pilot type (for positive pressure)
Internal pilot type
Operation type
Effective area〔Cv〕Note1
Port size Note2
Rc1/4, 3/8
Lubrication
Not required
0.2〜1.0MPa {2〜10.2kgf/cm2}
[29〜145psi.]
Main valve
Operating pressure range
External pilot
Proof pressure Note4
Response time
Note5
0〜1.0MPa {0〜10.2kgf/cm2}
[0〜145psi.]
0.2MPa〜−100kPa {2kgf/cm2〜−750.1mmHg}
[29psi.〜−29.53in.Hg]
0.2〜1.0MPa {2〜10.2kgf/cm2}Note3
[29〜145psi.]
0.2〜0.5MPa {2〜5.1kgf/cm2}Note7
[29〜73psi.]
1.5 {15.3} [218]
MPa {kgf/cm2} [psi.]
ON/OFF
ms
Maximum operating frequency
Hz
Minimum time to energize for self holding Note6
ms
45/25
25/30
25/35
45/25
25/35
45/25
50
50
25/30
25/35
50
5〜50 [41〜122]
1373 {140.0}
1373 {140.0}
m/s2 {G}
25/30
5
Operating temperature range (Atmosphere or media) °C [°F]
Shock resistance
External pilot type (for vacuum)
25
〔1.4〕
, 36
〔2.0〕
mm2
Pilot valve axial direction


 294.2 {30.0} 
294.2 {30.0}
Pilot valve axial direction


 294.2 {30.0} 
Mounting direction
1373 {140.0}
294.2 {30.0}
Pilot valve axial direction


 294.2 {30.0} 
294.2 {30.0}
Any
IP65 or equivalent (optional)
Environmental protection
Notes: 1. For details, see the effective area on p.672.
2. For details, see the port size on p.672.
3. When the main valve is 0.2〜1.0MPa [29〜145psi.], set the external pilot pressure to the same pressure as the main valve or larger, and at 1.0MPa [145psi.] or smaller.
4. The proof pressure is the pressure at which no damage, rupture, or external leaking can occur when maintained for 1 minute; it is not supposed to be used continuously.
5. The value when air pressure is at 0.5MPa [73psi.]. The 3-position shows the value when the valve is switched from the neutral position.
A maximum of 5ms should be added to the response time for AC specifications, depending on the timing of the switching phase.
6. For a double solenoid
7. The recommended value. Can be used up to a maximum of 1.0MPa [145psi.].
Solenoid Specifications
Item
Rated voltage
Operating voltage range
V
Rated frequency
Hz
DC24V Note
AC200V Note
AC100V Note
21.6〜26.4
90〜110
180〜220
（24±10％）
（100±10％）
（200±10％）
50
60
50
60
Current (when rated voltage is applied) mA（r.m.s）
42
11
6.5
Power consumption
1.0W
1.1VA
1.3VA
2.0
1.0
1.0
Allowable leakage current
mA
Insulation resistance
MΩ
Wiring type and lead wire length
mm [in.]
Color of lead wire
Color of LED indicator
Surge suppression (Standard equipment)
Over 100 (value at DC500V megger)
Grommet type, cabtyre cable (300 [11.8], 1000 [39], 3000 [118]), and DIN connectors
Red (COM), Black (14SA side), White (12SB side)
Red (14SA side), Green (12SB side)
Bridge diode
Notes: 1. Since AC-coils already have built-in bridge diodes, the starting current value is virtually identical to the energizing current value.
2. For long continuous energizing in AC-coils, consult us.
3. For both AC- and DC-coils, provide heat radiation measures to ensure that the ambient temperature (when used in a control box, the temperature inside the box) always
remains within the specified temperature range.
Safe Block Specifications
Effective Area〔Cv〕
mm2
Valve port size
Basic model
-02
（Rc1/4）
PA24HF5, PA24HF6
PA24HA5, PA24HA6
PA24HF7
PA24HA7
PA24HF8
PA24HA8
PA24HF9
PA24HA9
PA24F5, PA24F6, PA24F7
PA24F8, PA24F9
PA24A5, PA24A6, PA24A7
PA24A8, PA24A9
28
〔1.6〕
36
〔2.0〕
28
〔1.6〕
32
〔1.8〕
Effective area〔Cv〕
Basic model
-03
（Rc3/8）
PA24□-H
Response time (ON/OFF)
mm2
ms
22
〔1.2〕
40/40
（
1 P）
→4
（A）
,2
（B）
32
〔1.8〕
（
4 A）
,2
（B）
→5
（R1）
,3
（R2）36
〔2.0〕
（
1 P）
→4
（A）
,2
（B）
36
〔2.0〕
28
〔1.6〕
（
4 A）
,2
（B）
→5
（R1）
,3
（R2）32
〔1.8〕
28
〔1.6〕
22
〔1.2〕
25
〔1.4〕
Port Size
●Solenoid valves
●Sub-base piping specifications
PR
Basic model
（
1 P）
PR
X
（P2）
Rc1/4
M5×0.8
PA24□A□-02-25
Rc1/4
Rc1/4
Rc1/4
M5×0.8
M5×0.8
Rc1/4
M5×0.8
PA24□A□-03-25
Rc3/8
Rc3/8
Rc3/8
M5×0.8
M5×0.8
PA24□A□-04-25
Rc1/2
Rc1/2
Rc1/2
M5×0.8
M5×0.8
3 R2）
,（
5 R1）
（
4 A）
,（
2 B） （
Basic model
（
1 P）
PA24□F□-02
Rc1/4
Rc1/4
PA24□F□-03
Rc3/8
Rc3/8
Remark: Set the tightening torque for the screws of the solenoid valve PR
portion at 29.4N・cm {3kgf・cm} [2.6in・lbf] or less (only when -N is
selected).
Remark: The PR and X(P2) ports are available for the external pilot
specifications (for positive pressure and vacuum) only.
The pilot exhaust of internal pilot type is collected to 5(R1).
●Manifold
Manifold model
（
1 P）
PAM□F
PAM□F-04
（
4 A）
,（
2 B）（
3 R2）
,（
5 R1）
（
4 A）
,（
2 B）
X（P2）
PR
（
3 R2）
,（
5 R1）
-02
-03
Rc3/8
（Rc1/4）
（Rc3/8）
Rc3/8
Rc1/2
（Rc1/4）
（Rc3/8）
Rc1/2
PAM□A
Rc1/2
Rc1/4
Rc3/8
Rc1/2
Rc1/8
PAM□B
Rc1/2
Rc1/4
Rc3/8
Rc1/2
Rc1/8
PAM□FG
Rc3/8
（Rc1/4）
（Rc3/8）
Rc3/8
Rc1/8
Rc1/8
PAM□FG-04
Rc1/2
（Rc1/4）
（Rc3/8）
Rc1/2
Rc1/8
Rc1/8
PAM□AG
Rc1/2
Rc1/4
Rc3/8
Rc1/2
Rc1/8
Rc1/8
PAM□BG
Rc1/2
Rc1/4
Rc3/8
Rc1/2
Rc1/8
Rc1/8
Remark: The positions of the 4(A) and 2(B) piping ports ( ) are on the solenoid valve side.
Remark: The pilot exhaust of PAM□F and PAM□F-04 is collected to 5(R1).
Mass
●Direct piping specification, F type manifold specifications
g [oz.]
Note 1
Solenoid valve single unit (Port size)
Basic model
-02
（Rc1/4）
Mass calculation of each
unit
-03
（Rc3/8）
PA24□F7
PA24□F5
（n=number of units）
PA24□F6
PA24□F8
PA24□F7
PA24□F5
PA24□F6
PA24□F8
PA24□F9
PAM□F
(80×n)＋90
PAM□F-04
(80×n)＋270 [(2.82×n)＋9.52]
[(2.82×n)＋3.17]
203 [7.16]
215 [7.58]
Calculation example: PBM4F
〜 3 PA24F5-03-G1 D4
stn.1〜
stn.4
PA-BP
（80×4）
＋90＋
（197×3）
＋54＝1055g [37.21oz.]
241 [8.50]
Block-off plate
PA-BP
PA24□F9
197 [6.95]
209 [7.37]
235 [8.29]
54 [1.90]
Notes: 1. For the wiring specification of DIN connector (-39), add 12g [0.42oz.] to the
above, and for the cabtyre cable (-G3), add 3g [0.11oz.].
2. The wiring specifications assume a lead wire length of 300mm [11.8in.].
3. Plug R3/8: 14g [0.49in.], R1/2: 21g [0.74oz.]
●Sub-base piping specification, A type and B type manifold specifications
g [oz.]
Additional mass（n=number of units）
Solenoid valve single unit Note1
Basic model
Mass calculation of
each unit
PA24□A7
（n=number of units） PA24□A5 PA24□A6 PA24□A8
PA24□A9
PA24□A□
Port size specification
Ported manifold
-02
-03
Block-off
Piping block
-04
-B2
-B3
（Rc1/4） （Rc3/8） （Rc1/2） （Rc1/4） （Rc3/8）
Safe block
plate
-H
PA-BP
82 [2.89]
54 [1.90]
200 [7.05] 190 [6.70] 260 [9.17]
PAM□A
(200×n)＋380 [(7.05×n)＋13.40] 212 [7.48] 224 [7.90] 250 [8.82] 20×n [0.71×n] 10×n [0.35×n]
55×n [1.94×n] 46×n [1.62×n]
PAM□B
(200×n)＋390 [(7.05×n)＋13.76]
20×n [0.71×n] 10×n [0.35×n]
55×n [1.94×n] 46×n [1.62×n]
Calculation example: PAM4A-B3
〜 3 PA24A5-G1 D4
stn.1〜
stn.4
PA-BP
（200×4）
＋380＋
（212×3）
＋
（46×3）
＋54＝2008g [70.83oz.]
Notes: 1. For the wiring specification of DIN connector (-39), add 12g
[0.42oz.] to the above, and for the cabtyre cable (-G3), add 3g
[0.11oz.].
2. The wiring specifications assume a lead wire length of 300mm
[11.8in.].
3. Plug R1/2: 21g [0.74oz.]
Cylinder Operating Speed
PA24HF5-03
PA24HA5-03-25
PA24F5-03
PA24A5-03-25
Measurement conditions
1200
1200
●Air pressure: 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length:
φ7.5×1000mm [39in.]
●Fitting: Quick fitting (Model: NTS10-03)
Load
●Load ratio＝
（％）
Cylinder theoretical thrust
●Cylinder stroke: 300mm [11.8in.]
1000
φ50
φ63
800
600
400
φ80
φ100
200
φ125
φ140
10 20
30 40
50
60
Load ratio
70
Delay time
Delay time
φ50
φ63
800
600
400
φ80
φ100
200
φ125
φ140
0
10 20
30 40
50
60
Load ratio
70
%
1mm/s = 0.0394in./sec.
Delay time
ｓ1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1000
%
φ140
φ125
φ100
φ80
φ63
φ50
10 20
30 40
50
60
Load ratio
Delay time
0
Maximum operating speed
Maximum operating speed
mm/s 1500
1400
Maximum operating speed
Maximum operating speed
mm/s 1500
1400
70
ｓ1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
φ140
φ125
φ100
φ80
φ63
φ50
10 20
30 40
50
60
Load ratio
%
70
%
Flow Rate
PA24 □
PA24H □
MPa 1.0
MPa 1.0
Supply pressure
MPa
Valve outlet pressure
0.8
0.9
0.7
0.7
0.6
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.1
0
0.8
1.0
0.8
0.6
0.2
0.1
500 1000 1500 2000 2500 3000
Flow rate R/min（ANR）
How to read the graph
When the supply pressure is 0.5MPa [73psi.]
and the flow rate is 1220R/min [43.1ft.3/min.]
(ANR), the valve outlet pressure becomes
0.4MPa [58psi.]
Supply pressure
MPa
0.9
Valve outlet pressure
0.9
0.7
0.9
0.6
0.7
0.5
0.6
0.5
0.4
0.4
0.3
0.3
0.2
0.1
0
1.0
0.8
0.2
0.1
1000
2000
3000
4000
5000
Flow rate R/min（ANR）
1MPa = 145psi.
1R/min = 0.0353ft.3/min.
Operating Principles and Symbols
5-port, 2-position
Single solenoid 14
（SA）
（
4 A）
（
2 B）
Double solenoid 14
（SA）
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
（
5 R1）
（
1 P）
（
3 R2）
P2注1 12
（SB）
PA24□F5
PA24□F6
Housing
Cover
Base
Piston
Adaptor
Major parts and materials
Valve body
5（R1）
4（A）
Stem
1
（P）
Materials
Body
Aluminum alloy (Anodized)
Stem
Aluminum alloy
Cover
2（B）
Valve
Lip seal
Parts
3（R2）
Base
Housing
Plastic
Adaptor
※Schematic diagram shows double solenoid (de-energizing
Lip seal
Synthetic rubber
Piston
Plastic
Body
Aluminum alloy (Anodized)
Manifold Block-off plate
Mild steel (Nickel-plated)
condition after energizing solenoid 12(SB)).
Seal
Synthetic rubber
5-port, 3-position
〔Both solenoid 14(SA) and 12(SB) are de-energized.〕
Closed center 14
（SA）
PA24□F7
（SA）
Exhaust center 14
PA24□F8
（
4 A）
（
2 B）
P2注1 12
（SB）
4（A）
1
（P）
3（R2）
5（R1）
4（A）
1
（P）
2（B）
1
（P）
2（B）
3（R2）
（
5 R1）
（
1 P）
（
3 R2）
P2注1 12
（SB）
5（R1）
4（A）
2（B）
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
P2注1 12
（SB）
5（R1）
14
（SA）
PA24□F9
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
Pressure center
3（R2）
PA Series Manifold Order Codes
Model
q
w
e
r
t
Number of units
Manifold type
Pilot
specification
Air supply and
exhaust block
Manifold outlet
specification
Manifold model
F type manifold
（Direct piping type）
A type manifold
(Side piping type)
F
PAM
2
･
･
･
16
A
B type manifold
(Bottom piping type)
q Number of units
K
2
3
2 units
B
Blank
Blank
G
-04
G
r Air supply and exhaust block size
K
G
※F type manifold only
Blank Rc3/8
Rc1/2
w Manifold type
K
B
B type manifold
(Bottom piping type)
※See next page.
stn.2 PA24□□-□-□-□……
-04
A type manifold
(Side piping type)
y Mounted valve
K
stn.1 PA24□□-□-□-□……
16 16 units
A
stn.1
･
･
･
stn.□
-02
-03
-B2
-B3
Blank
3 units
F type manifold
(Direct piping
type)
-02
-03
-B2
-B3
Blank
⁝
F
y
Mounted valve
⁝
⁝
Note: For the stn. No., enter the valve
specifications in the order of the
required stations, or 1, 2, ..., from
the left when the valve is viewed
from the top.
t
K Manifold outlet specifications
-02 Manifold thread port Rc1/4
-03 Manifold thread port Rc3/8
stn. 1 2 3 4 …
※When using a block-off plate to
block, enter PA-BP.
-B2 Piping block Rc1/4
-B3 Piping block Rc3/8
※For A type and B type manifolds only
e Pilot specification
K
Blank Internal pilot manifold
G
External pilot manifold
Manifold Order Code Examples
●F type manifold (Direct piping type)
4 units DC24V
●A type manifold (Side piping type)
4 units DC24V
PAM4F
PAM4A-03
stn.1 PA24F5-02-G2-D4
stn.2 PA24F5-03-G2-D4
stn.3 PA24F6-03-G2-D4
stn.4 PA24F7-03-G2-D4
stn.1〜 2 PA24A5-G1-D4
stn.3
PA24A6-G1-D4
stn.4
PA24A7-G1-D4
PA Series Valve Order Codes (for valve single unit/manifold mounting)
q
w
e
r
t
y
Model
Valve
specification
Operation
type
Number
of ports
Piping
size
PR port
-02
-03
Blank
Blank
-32
-33
-34
Blank
F5
F6
F7
● Valve single unit
● For F type manifold
●For Sub-base piping
PA24
PA24H
●For A type manifold
●For B type manifold
F8
F9
Blank
A5
A6
A7
A8
A9
q Model
K
PA24
Standard type
（Effective area 25mm2〔Cv: 1.4〕）
（Effective area 36mm2〔Cv: 2.0〕）
F6
F7
F8
F9
A5
A6
A7
A8
A9
Blank
-02
-03
-04
-25
!1
!2
Environmental
protection
Voltage
-39
-G1
-G2
-G3
Blank
Blank
-1L
-3L
-P
-D4
-A1
-A2
i Wiring specification
K
Blank Internal pilot type
-39
G
External pilot type (for positive pressure) Note
V
External pilot type (for vacuum) Note
DIN connector
-G1 Grommet type
straight connector
-G2 Grommet type
L connector
-G3 Cabtyre Cable
Blank Standard (5-port valve)
5-port double solenoid
direct piping（single unit）/
for F type manifold
5-port 3-position
（
4 A）
（
2 B）
closed center
direct piping（single unit）/
for F type manifold
（
5 R1）
（
1 P）
（
3 R2）
5-port 3-position
（
4 A）
（
2 B）
exhaust center Note
direct piping（single unit）/
for F type manifold
（
5 R1）
（
1 P）
（
3 R2）
5-port 3-position
（
4 A）
（
2 B）
pressure center Note
direct piping（single unit）/
for F type manifold
（
5 R1）
（
1 P）
（
3 R2）
-32
3-port valve (Rc1/4) Note
-33
3-port valve (Rc3/8) Note
-34
Note
3-port valve (Rc1/2)
(Available for sub-base piping only)
Note: When the 5-port valve used as a 3-port
valve, plugs are supplied.
t Piping size
K
※Direct piping and sub-base piping only
Blank Without sub-base
5-port 3-position
（
4 A）
（
2 B）
exhaust center Note
sub-base piping/
for A and B type manifolds
（
5 R1）
（
1 P）
（
3 R2）
5-port 3-position
（
4 A）
（
2 B）
pressure center Note
sub-base piping/
for A and B type manifolds
（
5 R1）
（
1 P）
（
3 R2）
-1L
-3L
[11.8in.]
Lead wire 1000mm
[39in.]
Lead wire 3000mm
[118in.]
Note: Available for wiring specifications -G1, -G2,
and -G3 only.
!0 Safe block
K
※A type and B type manifolds only
-03
Rc3/8
-H
Rc1/2
y PR port
K
（
5 R1）
（
1 P）
（
3 R2）
Blank Lead wire 300mm
Blank Without safe block
(Available for sub-base piping only)
5-port 3-position
（
4 A）
（
2 B）
closed center
sub-base piping/
for A and B type manifolds
※Except DIN connector
Rc1/4
-04
5-port double solenoid
sub-base piping/
for A and B type manifolds
o
K Lead wire length
-02
Note: For the direct piping type, the 3(R2)
and 5(R1) ports become Rc1/4.
5-port single solenoid
sub-base piping/
for A and B type manifolds
Note: Not available for vacuum (V)
!0
Safe
block
-H
r Number of ports
K
5-port single solenoid
direct piping（single unit）/
for F type manifold
o
Lead wire
length
Blank
Note: The single unit valve is not compatible with
the external pilot type (for positive pressure,
and for vacuum). For use as a single unit,
select the sub-base piping specification.
w Valve specification
K
i
-N
e Operation type
K
PA24H Large flow rate type
F5
G
V
u
Wiring
Sub-base specification
※Direct piping (single unit) only
Blank No threads
-N
With female threads
（M5×0.8）
u Sub-base
K
※Sub-base piping only
Blank Without sub-base
(With 1 gasket,
2 mounting screws)
With safe block Note
Note: When ordering a manifold, the safe block
is available provided the manifold outlet
specifications are -B2 and -B3 (with piping block).
The safe block cannot be used with external pilot
types (for positive pressure and for vacuum).
!1 Environmental protection
K
Blank Standard
-P
IP65
or equivalent
Note: DIN connector (-39) is compatible with IP65
as the standard.
!2 Voltage
K
-D4 DC24V
-25
With sub-base
-A1 AC100V
-A2 AC200V
Additional Parts Order Codes for PA Series Manifold
Safe block
Piping block
(With 1 gasket, 2 mounting screws)
Block-off plate
Can be mounted at the same station where the
valve is installed (with 2 mounting screws).
PA -B2 Piping block Rc1/4
-B3 Piping block Rc3/8
PA-BP - F For F type manifold
- A For A type manifold
- B For B type manifold
PA -H
Replacement of pilot valve
Pilot valves are available as replacements. The
valves for 14 (SA) and 12 (SB) are distinguished
from the LED color. The 14 (SA) LED is red, and
the 12 (SB) LED is green. Select
the required type (a gasket and 2
mounting screws are supplied).
PA -D4 14 (SA) pilot valve, DC24V
-A1 14 (SA) pilot valve, AC100V
-A2 14 (SA) pilot valve, AC200V
-D4B 12 (SB) pilot valve, DC24V
-A1B 12 (SB) pilot valve, AC100V
-A2B 12 (SB) pilot valve, AC200V
Safe block
Notes: 1. Safe blocks can be
mounted only on A type
or B type manifolds,
and the manifold outlet
specifications are -B2
or -B3.
2. The piping block is not
included.
(with 1 gasket)
Gasket (for valve mounting)
(With 2 mounting screws)
PA -GS1 Gasket for F type
manifold
-GS2 Gasket for A type and B type
manifolds and sub-base piping
PA Series Dimensions of Single Valve Unit (mm)
20
（300） 43
17
1.5
8.4
1.4
23.8
Grommet type L connector
27.4
5（R1）
23
57
25
43
1（P）
3（R2）
2（B）
14
30.5
43
87
23
4（A）
135
Manual override
cover
When manual override
cover is open
26 （Rc3/8）
C 14A
21
PR port
(internal pilot exhaust port)
-N: M5×0.8
29
8
7.5
3
LED indicator
Manual override
23 （Rc1/4）
PA24□F5-G2
D
S
2-Rc1/4
5.5
3-Rc3/8［Rc1/4］
(Both sides)
37
3
18.6
2-φ4.2 counterboreφ7.6 Depth 3.5
(for manifold mounting)
26
D
15
S
2-φ5.4 counterboreφ9.4 Depth 6
Mounting hole
20
（300） 43
17
1.5
8.4
1.4
23.8
Grommet type L connector
27.4
5（R1）
23
57
25
43
1（P）
3（R2）
2（B）
14
30.5
43
87
23
4（A）
135
Manual override
cover
When manual override
cover is open
26 （Rc3/8）
12B C 14A
21
PR port
(internal pilot exhaust port)
-N: M5×0.8
29
8
7.5
3
LED indicator
Manual override
23 （Rc1/4）
PA24□F6-G2
2-M4×0.7 Depth 5〜11
Mounting thread
S
D
2-Rc1/4
5.5
3-Rc3/8［Rc1/4］
(Both sides)
37
3
18.6
2-φ4.2 counterboreφ7.6 Depth 3.5
(for manifold mounting)
26
2-φ5.4 counterboreφ9.4 Depth 6
Mounting hole
S
15
D
（300） 43
17
1.5
8.4
1.4
23.8
27.4
5（R1）
57
25
112
1（P）
68
2（B）
39
3（R2）
55.5
68
23
23
4（A）
2-Rc1/4
5.5
3-Rc3/8［Rc1/4］
(Both sides)
37
26
18.6
2-φ4.2 counterboreφ7.6 Depth 3.5
(for manifold mounting)
15
2-φ5.4 counterboreφ9.4 Depth 6
Mounting hole
For wiring specifications other than the grommet type L connector,
see p.679.
2-M4×0.7 Depth 30〜36
Mounting thread
160
Manual override
cover
When manual override
cover is open
26 （Rc3/8）
12B C 14A
29
PR port
(internal pilot exhaust port)
-N: M5×0.8
21
7.5
3
LED indicator
Manual override
23 （Rc1/4）
Grommet type L connector
20
8
PA24□F7-G2
PA24□F8-G2
PA24□F9-G2
2-M4×0.7 Depth 5〜11
Mounting thread
PA Series Dimensions of Single Valve Unit (mm)
PA24□A5-□-25
43 （300）
Grommet type L connector
8.4
1.5
27.4
LED indicator
Manual override
25
（
3 R2）
14
11
6
29
2（B）
41.5
75
57
25
（
1 P）
91
（
5 R1）
4（A）
25
135
8
Manual override
cover
PR
20
M5×0.8 external pilot exhaust port
(for external pilot specification)
17
1.4
21
23.8 10.6
2
S
13
5-Rc1/4（3/8）
2-φ5.4
Mounting hole
18.6
13
34
5
44
37
When manual override
cover is open
24
（62）
S
D
17
P2
14
M5×0.8 external pilot air supply port
(for external pilot specification)
●For Rc1/2 (common to all types)
17
M5×0.8 external pilot exhaust port
(for external pilot specification)
8
15
28
6
28
17
5-Rc1/2
37
42
28
28
PR
20
25
32
（70）
25
M5×0.8 external pilot supply port
(for external pilot specification)
Wiring Specifications
●DIN connector: -39
34
10
12
49
153
1
7
mPm
17
135
135
1
56
9
27
φ14
φ7
18
43
（300）
（300）
7.5
15.5
43
8
18
●Cabtyre cable: -G3
135
●Grommet type straight connector: -G1
PA24□A6-□-25
43 （300）
8.4
23.8 10.6
1.4
1.5
27.4
LED indicator
Manual override
75
（
3 R2）
14
11
6
29
（
2 B）
41.5
25
57
25
（P）
1
91
（
5 R1）
（
4 A）
25
135
8
Manual override
cover
PR
20
M5×0.8 external pilot exhaust port
(for external pilot specification)
17
21
Grommet type L connector
2
D
13
5-Rc1/4（3/8）
2-φ5.4
Mounting hole
18.6
13
34
When manual override
cover is open
5
44
37
24
（62）
D
S
17
P2
14
M5×0.8 external pilot air supply port
(for external pilot specification)
PA24□A7-□-25
PA24□A8-□-25
PA24□A9-□-25
43 （300）
1.5
LED indicator
8
Manual override
PR
20
M5×0.8 external pilot exhaust port
(for external pilot specification)
17
1.4
27.4
Grommet type L connector
8.4
10.6
21
23.8
Manual override
cover
25
（
3 R2）
27
39
11
6
29
（
2 B）
41.5
25
160
75
57
25
（P）
1
91
（
5 R1）
（
4 A）
5-Rc1/4（3/8） 13
18.6
2-φ5.4
Mounting hole
34
5
13
When manual override
cover is open
37
24
（62）
44
17
P2
14
M5×0.8 external pilot air supply port
(for external pilot specification)
Wiring Specifications
●DIN connector: -39
7.5
10
12
153〔178〕
17
1
56
9
135〔160〕
1
mPm
7
φ14
φ7
18
43
27
（300）
135〔160〕
（300）
34
15.5
43
8
18
●Cabtyre cable: -G3
135〔160〕
●Grommet type straight connector: -G1
49
The figures in parentheses〔
〕are for the 3-position case.
PA Series Dimensions of Manifold (mm)
PAM□F
Direct piping type
47
P
（7）
〔
（10）
〕
PR
23
4（A）
4（A）
4（A）
5（R1）
43
（
1 P）
（
1 P）
3（R2）
P2
（25）
13.2
PR
4（A）
5（R1）
26
160
25.5
26
25.5
42.5
4-φ5.4
Mounting
hole
2（B）
S
2（B）
S
2（B）
3（R2）
2（B）
91
8.2
Manual override
cover
153
LED indicator
135
〔17〕
26
mPm
2-Rc1/8 pilot exhaust port
[for external pilot specification]
(with 1 plug)
24
26
（Pitch）〔29〕
29.5
（18）
24
10.5
13
6-Rc3/8
(with 3 plugs)
Unit Dimensions
L〔L1〕
〔10〕 7
19
P2
D
23.8
23.6
stn.1 stn.2 stn.3 stn.4 stn.5
●Groove details
PA24F6-03-39
PA24HF5-03-G2
3.3
PA24F7-02-G1
S
S
37
62
〔L1〕
82
13
100
86
106
14
124
110
130
15
148
134
154
16
172
158
178
17
196
182
202
18
220
206
226
19
244
230
250
10
268
254
274
11
292
278
298
12
316
302
322
13
340
326
346
14
364
350
370
15
388
374
394
16
412
398
418
Note: The figures in parentheses〔 〕
are for the external pilot
specification.
〔17〕
（62）
24
Groove for M5 nut
(for manifold mounting)
D
8.6
Groove for M3 nut
(cannot be used to mount
the manifold in place)
〔10〕
D
5.6
5
P
76
S
2
PA-BP
Block-off plate
L
12
2-Rc1/8 external pilot port
〔10〕 (for external pilot specification)
(with 1 plug)
D
3
5
5.5
1.5
8.1
PA24F5-02-G1
Number of units
PAM□F-04
Direct piping type
48
4-φ5.4
Mounting
hole
PR
4（A）
5（R1）
46
1（P）
（
1 P）
3（R2）
2（B）
（22）
P2
S
19
2（B）
S
2（B）
3（R2）
2（B）
94
4（A）
33
23
32
4（A）
29
4（A）
5（R1）
26
156
138
PR
P2
D
23.8
23.6
19
stn.1 stn.2 stn.3 stn.4 stn.5
PA24F6-03-39
PA24HF5-03-G2
PA24F5-02-G1
PA24F7-02-G1
S
PA-BP
Block-off plate
〔29〕
〔18〕
1
27
Number of units
L
P
12
114
102
120
108
13
138
126
144
132
14
162
150
168
156
15
186
174
192
180
16
210
198
216
204
17
234
222
240
228
18
258
246
264
252
19
282
270
288
276
10
306
294
312
300
11
330
318
336
324
12
354
342
360
348
13
378
366
384
372
14
402
390
408
396
15
426
414
432
420
16
450
438
456
〔L1〕〔P1〕
444
Note: The figures in parentheses〔 〕are for the
external pilot specification.
2-Rc1/8 external pilot port
(for external pilot specification)
(with 1 plug)
D
〔29〕
D
（63）
S
D
160
Manual override
cover
S
6-Rc3/8
(with 3 plugs)
32
（6）
24
45〔48〕
（Pitch）
〔29〕
LED indicator
〔18〕
45.5
24
91
mPm
P〔P1〕
10.5
6
〔29〕
（18）
20
14
2-Rc1/8 pilot exhaust port
[for external pilot specification]
(with 1 plug)
14.5
Unit Dimensions
L〔L1〕
PAM□A-0□
83
Side piping type
2-Rc1/8 pilot exhaust port
(with 1 plug)
L
55
LED indicator
49
Manual override
cover
P
24
L
P
2
87
60
3
111
84
4
135
108
5
159
132
6
183
156
7
207
180
8
231
204
9
255
228
10
279
252
11
303
276
12
327
300
13
351
324
38
14
375
348
46
15
399
372
53
16
423
396
（18）
mPm
39.4
10.5
4-φ6.4
Mounting
hole
154
95
160
52
（24）
S
25.5
6
21
P2
13
30
3（R2）
10
136
16
30
5（R1）
44.5
PR
1（P）
A→
2-Rc1/8 external pilot port
(for external pilot specification)
(with 1 plug)
Unit Dimensions
（13.5）
24 31.5
（Pitch）
Number of units
44.2
6-Rc1/2
(with 3 plugs)
43
13.5
S
23.8
23.6
Stn.1 Stn.2 Stn.3 Stn.4
PA24A5-G1
●Viewed from A
PAM□B-0□ (for bottom piping type)
2-Rc3/8（Rc1/4）
Per each
station
PA24A6-39
PA-BP
Block-off plate
D
3
30
3.3
2（B）
4（A）
4（A）
6.5
2（B）
14.5
3
25
60
1.5
（98）
61
2（B）
（95）
2（B）
（13）
13 26.5
4（A）
D
4（A）
S
26
37
S
PA24A7-G2
5.6
Dimensions of groove for M3 nut (2:1)
(cannot be used to mount the manifold)
3
24
Note: The side piping type and bottom piping type cannot be selected on the same manifold. Select either piping type for the manifold.
PAM□A-B□
83
Side piping type
2-Rc1/8 pilot exhaust port
(with 1 plug)
L
55
LED indicator
49
Manual override
cover
P
24
（13.5）
24 31.5
（Pitch）
L
P
2
87
60
3
111
84
4
135
108
5
159
132
6
183
156
7
207
180
8
231
204
9
255
228
10
279
252
11
303
276
12
327
300
13
351
324
14
375
348
46
15
399
372
53
16
423
396
（18）
mPm
4-φ6.4
Mounting
hole
95
136
52
25.5
D
12
（24）
S
6
21
P2
13
30
10
3（R2）
1（P）
A→
160
30
5（R1）
44.5
PR
154
16
10.5
6-Rc1/2
(with 3 plugs)
2-Rc1/8 external pilot port
(for external pilot specification)
(with 1 plug)
Unit Dimensions
Number of units
44.2
39.4
43
13.5
23.8
38
23.6
Stn.1 Stn.2 Stn.3 Stn.4
PA24A5-G1
●Viewed from A
PAM□B-B□ (for bottom piping type)
PA24A6-39
S
PA24A7-G2
PA-BP
Block-off plate
D
24
2（B）
4（A）
4（A）
60
（98）
61
2（B）
17.5 25
30.5
31.5
（13）
2（B）
25
2（B）
D
4（A）
S
4（A）
（95）
37
2-Rc3/8（Rc1/4）
Per each
station
Note: The side piping type and bottom piping type cannot be selected on the same manifold. Select either piping type for the manifold.
PA Series Dimensions of Manifold with Safe Blocks (mm)
PAM□A
PAM□B
Side piping type
Bottom piping type
24
31.5
（Pitch）
79
136
195
3（R2）
1（P）
A→
5（R1）
136
PR
160
49
P2
42.3
S
Residual pressure exhaust manual override
Safe block
32.3 10
49
（98）
（147）
Safe block
7
Residual pressure exhaust
manual override
23.8
For PA24□A7, A8, A9
（3-position）
For PA24□A5, A6
（2-position）
●Viewed from A
37
S
60
4（A）
4（A）
4（A）
2（B）
2（B）
2（B）
4（A）
Residual pressure exhaust manual override
7
（95）
（98）
D
2（B）
SOLENOID VALVES
SERIES
Specifications
Basic models and valve functions
Basic model
PB24□C7
PB24□C5
PB24□C6
PB24□C8
Item
PB24□C9
Number of positions
3 positions
2 positions
Number of ports
5
Double solenoid Note
Single solenoid
Valve function
Closed center, Exhaust center, Pressure center
Remark: For the specifications and order codes, see p.689〜692.
Note: 2-position double solenoid valve can be switched to a single solenoid valve. For details, see p.665.
Specifications
Basic model
PB24□C7G
PB24□C7
PB24□C5
PB24□C6
Item
PB24□C8 PB24□C5G PB24□C6G PB24□C8G PB24□C5V PB24□C6V PB24□C7V
PB24□C9G
PB24□C9
Air
Media
External pilot type (for positive pressure)
Internal pilot type
Operation type
Effective area〔Cv〕Note1
Port size Note2
Rc1/4, 3/8
Lubrication
Not required
0.2〜1.0MPa {2〜10.2kgf/cm2}
[29〜145psi.]
Main valve
Operating pressure range
External pilot
Proof pressure Note4
0〜1.0MPa {0〜10.2kgf/cm2}
[0〜145psi.]
0.2MPa〜−100kPa {2kgf/cm2〜−750.1mmHg}
[29psi.〜−29.53in.Hg]
0.2〜1.0MPa {2〜10.2kgf/cm2}Note3
[29〜145psi.]
0.2〜0.5MPa {2〜5.1kgf/cm2}Note7
[29〜73psi.]
1.5 {15.3} [218]
MPa {kgf/cm2} [psi.]
Response time Note5 ON/OFF
ms
Maximum operating frequency
Hz
Minimum time to energize for self holding Note6
ms
40/25
25/25
35/45
40/25
35/45
40/25
50
50
25/25
35/45
50
5〜50 [41〜122]
1373 {140.0}
1373 {140.0}
m/s2 {G}
25/25
5
Operating temperature range (Atmosphere or media) °C [°F]
Shock resistance
External pilot type (for vacuum)
25
〔1.4〕
, 36
〔2.0〕
mm2
Pilot valve axial direction


 294.2 {30.0} 
294.2 {30.0}
Pilot valve axial direction


 294.2 {30.0} 
Mounting direction
1373 {140.0}
294.2 {30.0}
Pilot valve axial direction


 294.2 {30.0} 
294.2 {30.0}
Any
IP65 or equivalent (optional) available
Environmental protection
Notes: 1. For details, see the effective area on p.686.
2. For details, see the port size on p.686.
3. When the main valve is 0.2〜1.0MPa [29〜145psi.], set the external pilot pressure to the same pressure as the main valve or larger, and at 1.0MPa [145psi.] or smaller.
4. The proof pressure is the pressure at which no damage, rupture, or external leaking can occur when maintained for 1 minute; it is not supposed to be used continuously.
5. The value when air pressure is at 0.5MPa [73psi.]. The 3-position shows the value when the valve is switched from the neutral position.
A maximum of 5ms should be added to the response time for AC specifications, depending on the timing of the switching phase.
6. For a double solenoid
7. The recommended value. Can be used up to a maximum of 1.0MPa [145psi.].
Solenoid Specifications
Item
Rated voltage
Operating voltage range
V
Rated frequency
Hz
DC24V Note
AC200V Note
AC100V Note
21.6〜26.4
90〜110
180〜220
（24±10％）
（100±10％）
（200±10％）
50
60
50
60
Current (when rated voltage is applied) mA（r.m.s）
42
11
6.5
Power consumption
1.0W
1.1VA
1.3VA
2.0
1.0
1.0
Allowable leakage current
mA
Insulation resistance
MΩ
Wiring type and lead wire length
mm [in.]
Color of lead wire
Color of LED indicator
Surge suppression (Standard equipment)
Over 100 (value at DC500V megger)
Grommet type, cabtyre cable (300 [11.8], 1000 [39], 3000 [118]), and DIN connectors
Red (COM), Black (14SA side), White (12SB side)
Red (14SA side), Green (12SB side)
Bridge diode
Notes: 1. Since AC-coils already have built-in bridge diodes, the starting current value is virtually identical to the energizing current value.
2. For long continuous energizing in AC-coils, consult us.
3. For both AC- and DC-coils, provide heat radiation measures to ensure that the ambient temperature (when used in a control box, the temperature inside the box) always
remains within the specified temperature range.
Port Size
Effective Area〔Cv〕
mm2
Valve port size
Basic model
-□1
（Rc1/8）-□2
（Rc1/4）
PB24HC5
22
〔1.2〕
32
〔1.8〕
36
〔2.0〕
PB24HC7
22
〔1.2〕
28
〔1.6〕
32
〔1.8〕
PB24HC8
22
〔1.2〕
28
〔1.6〕
PB24HC9
22
〔1.2〕
28
〔1.6〕
PB24C5, PB24C6
PB24C7, PB24C8
PB24C9
18
〔1.0〕
22
〔1.2〕
PB24HC6
（
4 A）
,（
2 B）
（
1 P）
-□3
（Rc3/8）
Rc1/2
（
1 P）
→4
（A）
,2
（B）
-□1
-□2
-□3
Rc1/8
Rc1/4
Rc3/8
（
3 R2）
,（
5 R1）
X
（P2）
Rc1/2
Rc1/8
32
〔1.8〕
（
4 A）
,2
（B）
→5
（R1）
,3
（R2）36
〔2.0〕
（
1 P）
→4
（A）
,2
（B）
36
〔2.0〕
（
4 A）
,2
（B）
→5
（R1）
,3
（R2）32
〔1.8〕
25
〔1.4〕
Notes: 1. Caution should be exercised that the effective area is reduced by
about 10% when using a front-surface piping block.
2. In the case of 2 or more valve units, the effective area could be
reduced by about 5%, depending on the flow path.
Safe Block Specifications
Response time (ON/OFF)
Effective area
〔Cv〕
Basic model
PB24□-H
mm2
ms
22
〔1.2〕
40/40
Mass
●Non-plug-in type manifold
g [oz.]
Basic mass
Additional mass with options
Mass calculation of each unit（n=number of units）
wPort size
qValve model Note1
PB24□C5
PB24□C6
268 [9.45]
Additional
mass
PB24□C7
PB24□C8
PB24□C9
310 [10.93]
-□1
-□2
-□3
（Rc1/8）
（Rc1/4）
（Rc3/8）
61 [2.15]
55 [1.94]
46 [1.62]
（mass per 1 unit）
Block-off
plate
-H
PB-BPN
-Z
（Rc1/8）
-Z
（Rc1/4）
-Z
（Rc3/8）
82 [2.89]
152 [5.36]
180 [6.35]
176 [6.21]
168 [5.93]
450
[15.87]
（q＋w）
×n
Calculation example: PBM5N
〜 5 PB24C5-T3-39-H-D4
stn.1〜
（268＋12＋46）
×5＋450＋
（82×5）
＝2490g [87.83oz.]
Individual air supply and exhaust spacer
Safe block
Notes: 1. For the wiring specification of DIN connector (-39), add 12g [0.42oz.], and
add 3g [0.11oz.] for the cabtyre cable (-G3).
2. The wiring specifications assume a lead wire length of 300mm [11.8in.].
3. Plug R1/8: 3g [0.11oz.], R1/2: 21g [0.74oz.]
●Plug-in type and serial transmission type manifold
g [oz.]
Basic mass（n=number of units）
Mass calculation of each unit
qValve model
PB24□C5
PB24□C6
wPort size
PB24□C7
PB24□C8
PB24□C9
270 [9.52] 312 [11.01]
-□1
-□2
-□3
Cable Note
-U□
-E□
（q＋w）
×n
55 [1.94]
（mass per 1 unit）
Wiring specification
（Rc1/8） （Rc1/4） （Rc3/8）
61 [2.15]
Additional mass with options
Additional mass
＋
46 [1.62] （15×n）
585
[(0.53×n）
＋
20.63]
Calculation example: PBM5P-TL
〜 5 PB24HC5-T3-B-D4
stn.1〜
（270＋46）
×5＋880＝2460g [86.77oz.]
Terminal
block box
D-sub
-T□
-D□
S
-H
880
[31.04]
765
[26.98]
960
[33.86]
82
[2.89]
Serial
Block-off
Safe block
transmission
plate
Individual air supply and exhaust side spacer
-Z
-Z
-Z
PB-BP□ （Rc1/8） （Rc1/4） （Rc3/8）
157
[5.54]
180
[6.35]
176
[6.21]
Notes: 1. The cable specifications assume a cable length of 700mm [27.6in.].
2. Plug R1/8: 3g [0.11oz.], R1/2: 21g [0.74oz.]
168
[5.93]
Cylinder Operating Speed
PB24HC5-□3
PB24C5-□3
Measurement conditions
mm/s 1500
1400
1200
1200
●Air pressure: 0.5MPa {5.1kgf/cm2} [73psi.]
●Piping inner diameter and length:
φ7.5×1000mm [39in.]
●Fitting: Quick fitting (Model: NTS10-03)
Load
●Load ratio＝
（％）
Cylinder theoretical thrust
●Cylinder stroke: 300mm [11.8in.]
1000
φ50
φ63
800
600
400
φ80
φ100
200
φ125
φ140
0
10 20
30 40
50
60
Delay time
φ50
φ63
800
600
400
φ80
φ100
200
φ125
φ140
10 20
30 40
50
60
Load ratio
%
Delay time
70
%
1mm/s = 0.0394in./sec.
Delay time
ｓ1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1000
0
70
Load ratio
φ140
φ125
φ100
φ80
φ63
φ50
10 20
30 40
50
60
Delay time
Maximum operating speed
Maximum operating speed
Maximum operating speed
Maximum operating speed
mm/s 1500
1400
70
Load ratio
ｓ1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
φ140
φ125
φ100
φ80
φ63
φ50
10 20
30 40
50
60
Load ratio
%
70
%
Flow Rate
PB24 □
PB24H □
MPa 1.0
MPa 1.0
Supply pressure
MPa
Valve outlet pressure
0.8
0.9
0.7
0.7
0.6
0.5
0.5
0.4
0.4
0.3
0.3
0.2
0.1
0
0.8
1.0
0.8
0.6
0.2
0.1
500 1000 1500 2000 2500 3000
Flow rate R/min（ANR）
How to read the graph
When the supply pressure is 0.5MPa
[73psi.] and the flow rate is 1220R/min
[43.1ft.3 /min.] (ANR), the valve outlet
pressure becomes 0.4MPa [58psi.]
Supply pressure
MPa
0.9
Valve outlet pressure
0.9
0.7
0.9
0.6
0.7
0.5
0.6
0.5
0.4
0.4
0.3
0.3
0.2
0.1
0
1.0
0.8
0.2
0.1
1000
2000
3000
4000
5000
Flow rate R/min（ANR）
1MPa = 145psi.
1R/min = 0.0353ft.3/min.
Operating Principles and Symbols
5-port, 2-position
Single solenoid 14
（SA）
（
4 A）
（
2 B）
Double solenoid 14
（SA）
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
PB24□C5
（
5 R1）
（
1 P）
（
3 R2）
PB24□C6
P2注1 12
（SB）
P2注1
Housing
Cover
Base
Piston
Exhaust valve
Adaptor
Valve body
5（R1）
Stem
5（R1）
Plate
（
1 P）
Parts
（
1 P）
Lip seal
3（R2）
Major parts and materials
3（R2）
Double & Single
Switching pin
Stem
Aluminum alloy
Base
Plastic
Housing
Adaptor
2（B）
4（A）
Aluminum die-casting
Cover
Female thread
block
2（B）
Materials
Body
Switching pin
4（A）
〔De-energized〕 〔De-energizing condition after energizing solenoid 12 (SB)〕
Lip seal
Synthetic rubber
Piston
Plastic
Exhaust valve
Synthetic rubber
5-port, 3-position
〔Both solenoid 14 (SA) and 12 (SB) are de-energized.〕
Closed center 14
（SA）
PB24□C7
（SA）
Exhaust center 14
PB24□C8
（
4 A）
（
2 B）
PB24□C9
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
P2注1 12
（SB）
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
5（R1）
5（R1）
（
1 P）
（
1 P）
（
1 P）
3（R2）
3（R2）
3（R2）
4（A）
2（B）
4（A）
（
5 R1）
（
1 P）
（
3 R2）
P2注1 12
（SB）
P2注1 12
（SB）
5（R1）
2（B）
Pressure center 14
（SA）
2（B）
4（A）
PB Series Manifold Order Codes
q
Number of
units
Model
w
Manifold type
e
r
Wiring specification
Transmission block
specification
t
y
Wiring position Environmental
protection
(transmission block)
Manifold model
Non-plug-in
type
N
Plug-in type
1
･
･
･
16
PBM
Serial
transmission
type
P
Blank
-P
-01
-02
-11
-21
-31
-32
r
K
-41
-42
-51
-52
-61
-71
-81
-A1
-A2
-B1
-C1
-D1
Transmission block specification ※Serial transmission type only
1 unit Note: The maximum number of units that
2 units
⁝
16 16 units
can be controlled varies according
to the number of solenoids. For
details, see p.693. When used with
an individual air supply and exhaust
spacer, the number of valve units
and the number of individual air
supply/exhaust spacers determines
the total number of units. For
details, see the order code
examples on p.691.
w Manifold type
K
N
-UL -DUL -TL
-UR -DUR -TR
-EL -DEL
-ER -DER
S
q Number of units
K
1
2
u
Mounted valve
P
Plug-in type
S
Serial transmission type
-01 For UNI-WIRE System (16 outputs)
-02 For UNI-WIRE System (8 outputs)
-11 For Mitsubishi Electric MELSECNET/MINI-S3
(maximum of 12 units)
-UR Cable outlet at top surface on right
(maximum of 12 units)
-EL Cable outlet at side surface on left
-ER Cable outlet at side surface on right
IP 65 or
equivalent Note
Note: Plug-in type can be set for terminal block
box specifications only. The non-plug-in
type is compatible with IP65 or equivalent as standard. Both types require
selection of -P for the valve side.
u Mounted valve
K
-32 For OMRON B7A Link Terminal (High speed)
※See next page.
-41 For KOYO ELECTRONICS INDUSTRIES SA Bus (16 outputs)
stn.1 PB24□□-□-□-□……
-42 For KOYO ELECTRONICS INDUSTRIES SA Bus (8 outputs)
stn.2 PB24□□-□-□-□……
-61 For Mitsubishi Electric MELSEC I/O LINK
-UL Cable outlet at top surface on left
Environmental protection ※Plug-in type/Serial transmission type
-31 For OMRON B7A Link Terminal (Standard)
-51 For SUNX S-LINK (16 outputs)
※Plug-in type only
-P
y
K
-P
-52 For SUNX S-LINK (8 outputs)
e Wiring specification
K
Blank
-R
Blank Standard
-21 For OMRON SYSBUS Wire System
Non-plug-in type
Blank
stn.1
･
･
･
stn.□
⁝
For the stn. number, enter the valve
⁝ Note: specifications
for the required stations,
numbering them 1,2,... from the left, as
viewed with the solenoid on top.
stn. 1 2 3 4 …
-71 For Fuji Electric FA Components & Systems T Link Mini
-81 For KEYENCE KZ-R
※For the block-off plate, see p.691.
-A1 For OMRON CompoBus/S (16 outputs)
-A2 For OMRON CompoBus/S (8 outputs)
-B1 For Mitsubishi Electric CC-Link
-C1 For OPCN-1 (former JPCN-1)
-D1 For DeviceNet (CompoBus/D)
Note: For details, see p.695〜697.
-DUL D-sub connector at top surface
on left side mounting Note
-DUR D-sub connector at top surface
on right side mounting Note
t Wiring position
K
※Serial transmission type only
Blank Left-side mounting
-DEL D-sub connector at side surface
on left side mounting Note
-DER D-sub connector at side surface
on right side mounting Note
-TL
Terminal block box on left side
mounting Note
-TR
Terminal block box on right side
mounting Note
Note: For pin (terminal) locations, see p.693.
-R
Right-side mounting
Manifold Order Code Example
●Serial transmission type, 4 units, DC24V
PBM4S-B1-P
stn.1 PB24C5-T2-B-P-D4
stn.2 PB24C5-D-T3-B-P-D4
stn.3 PB24C6-T3-B-P-D4
stn.4 PB24C7-T3-B-P-D4
PB Series Mounted Valve Order Codes
(cannot be used as a single valve unit)
q
Model
w
e
Valve
Operation
type
specification
r
Number
of ports
i
o
!2
!3
Lead wire
length
Safe
block
Individual air
supply and
exhaust spacer
!1
Piping
Wiring
Wiring connection
specification specification specification
t
Port
isolator
Environmental
protection
Voltage
-39
-G1
-G2
-G3
Blank
Blank
Blank
Blank
Blank
-H
-Z
-SP
-P
●Non-plug-in type
●Plug-in type
(cable specification)
C5
C6
C7
C8
C9
PB24
PB24H
●Plug-in type
Blank
G
V
Z
GZ
VZ
Blank
-31
-32
-33
(D-sub connector,
terminal block box)
●Serial
transmission type
-T1
-T2
-T3
-U1
-U2
-U3
y
u
!0
-1L
-3L
Blank
-D
Blank
-1L
-3L
-D4
-A1
-A2
Blank
-B
-D
●Various types of block-off plates are available as options. For details, see p.691.
q Model
K
t Piping specification
K
PB24
-T1 Front surface piping Rc1/8
Blank Without safe block
-T2 Front surface piping Rc1/4
-H
-T3 Front surface piping Rc3/8
Note: Cannot be used with external pilot types
(for positive pressure and for vacuum).
Standard type
(Effective area 25mm2〔Cv: 1.4〕)
PB24H Large flow rate type
2
(Effective area 36mm〔Cv:
2.0〕)
w Valve specification
K
C5
5-port
single solenoid
C6
5-port
double solenoid
-U1 Top surface piping Rc1/8
-U2 Top surface piping Rc1/4
-U3 Top surface piping Rc3/8
y Wiring specification
K
C7
5-port 3-position
closed center
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
C8
5-port 3-position
exhaust centerNote
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
C9
5-port 3-position
pressure centerNote
（
4 A）
（
2 B）
（
5 R1）
（
1 P）
（
3 R2）
Note: Not available for vacuum (V)
-39
DIN connector
-G1 Grommet type
straight connector
V
External pilot type (for vacuum)
Z
Internal pilot type with individual air supply
and exhaust spacer Note
GZ
External pilot type with individual air supply and
exhaust spacer (for positive pressure) Note
VZ
External pilot type with individual air supply and
exhaust spacer (for vacuum) Note
Note: Dedicated valves for use with individual air supply
and exhaust spacers.
Note: For details, see the order code examples on p.691.
r Number of ports
K
-B
※Plug-in type/serial transmission type
-32
Note
3-port valve (Rc1/4)
-33
3-port valve (Rc3/8)Note
Note: When the 5-port valve is used as a 3-port
valve, plugs are supplied.
!1 Port isolator
K
With port isolator
for P port
Note: Port isolator can be mounted in only 1 location
(1 station) in the manifold. Port isolator is
installed between the specified station and the
station to its immediate left (the smaller stn.
no.) at shipping.
!2 Environmental protection
K
Blank Standard
Blank Packed wiring: Wiring connection with each
mounted valve.
-D
Double wiring: Provides wiring connections for
a double solenoid even when the
specification is for a single
solenoid.
i Lead wire length
K
※Except DIN-type connector
Blank Lead wire 300mm
3-port valve (Rc1/8)Note
Note: Always enter -Z when selecting dedicated
valves for the manifolds.
For details, see the order code examples on
p.691.
-SP
Always enter -B for D-sub connector,
terminal block box and serial
transmission types.
u Wiring connection spec.
K
Blank Standard (5-port valve)
-31
With individual air supply and exhaust spacer Note
-G2 Grommet type
-G3 Cabtyre cable
External pilot type (for positive pressure)
Blank Without individual air supply and exhaust spacer
Blank Without port isolator
Blank Internal pilot type
G
With safe block Note
!0 Individual air supply and exhaust spacer
K
-Z
※No cable specification entry
L connector
e Operation type
K
o Safe block
K
-1L
-3L
[11.8in.]
(700mm
[27.6in.])
Lead wire 1000mm [39in.]
(1500mm [59in.])
Lead wire 3000mm [118in.]
(3000mm [118in.])
Note: Not available in wiring specification -39. The
figures within parentheses ( ) are for plug-in type
cable specification. The cable length shows the
distance from each valve.
-P
IP65 or equivalent Note
Note: The DIN connector (-39) is compatible with
IP65 or equivalent as standard. In the case
where the IP65 or equivalent is used, select -P
for both the manifold order code and the valve
order code.
!3 Voltage
K
-D4 DC24V
-A1 AC100V Note
-A2 AC200V Note
Note: Not available in serial transmission type.
Order code examples when using the individual air supply and exhaust spacer
Not functional as an individual air supply and
exhaust spacer alone. It works when used in
combination with the dedicated valve (PB24
□ Z). Since the spacer is added as part of the
total number of valve units, take consideration
of the maximum number of units allowed in
the manifold. In the mounting case at right,
the station configuration is stn.1〜stn.3., but
the number of units in the manifold is counted
as 4 units. For the air supply and exhaust port
positions, see p.668.
〈Mounting example〉
PB24C6Z-T3-Z-D4 (Dedicated valve)
Individual air supply and exhaust spacer
Note: Occupies 1 station space on the right side
of the dedicated valve.
Order Code Example
●Plug-in type cable specification
4 units DC24V
Num stn.1
ber stn.2
1 of un stn.3
its
2
3
4
PBM4P-EL
stn.1 PB24C5-T2-D4
stn.2 PB24C5-T3-D4
stn.3 PB24C6Z-T3-Z-D4
PB Series Manifold Options Order Codes
Block-off plate
PB-BP q
w
e
Non-plug-in type
When valves are expected to be installed in the future, use these as mounted on a manifold.
Note that this configuration is different from the conventional plate type block-off plates, and it is the block
shape.
For instructions for mounting and removal, see the valve mounting and removal on p.667.
For D-sub connector, terminal block box, serial transmission type
〈Mounting example〉
qSpecification
N
M
K
K1
K3
Cable specification (700mm [27.6in.])
Cable specification (1500mm [59in.])
Cable specification (3000mm [118in.])
Order Code Example
wWiring connection specification Note eEnvironmental protection Note
S Single wiring
D Double wiring
●Plug-in type cable specification
4 units DC24V
Blank Standard
-P
IP65 or equivalent
PBM4P-EL
(Note: Except non-plug-in type) (Note: Non-plug-in type is
compatible with IP65 or
equivalent as standard)
When used in combination with individual air supply and exhaust spacer
PB-BP q
w -Z e
r
stn.1 PB24C5-T2-D4
stn.2 PB24C5-T3-D4
stn.3 PB24C6-T3-D4
stn.4 PB-BPKD
t
qSpecification
wWiring connection specification Note ePiping direction
N Non-plug-in type
M For D-sub connector, terminal block box,
K
PB-BP □□
Block-off plate
T Front surface piping
U Top surface piping
S Single wiring
D Double wiring
serial transmission type
(Note: Except non-plug-in type)
Cable specification (700mm
[27.6in.])
rPiping size
K1 Cable specification (1500mm
[59in.])
K3 Cable specification (3000mm
1 Rc1/8
2 Rc1/4
3 Rc3/8
[118in.])
tEnvironmental protection Note
Blank Standard
-P
IP65 or equivalent
(Note: Non-plug-in type is compatible with IP65 or
equivalent as standard)
Additional Parts Order Codes for PB Series
Replacement of pilot valve
Pilot valves are available as replacements.
The valves for 14 (SA) and 12 (SB) are
distinguished from the LED color. The 14
(SA) LED is red, and the 12 (SB) LED is
green. Select the required type (a gasket
and 2 mounting screws are supplied).
PB -D4 14 (SA) pilot valve, DC24V
-A1 14 (SA) pilot valve, AC100V
-A2 14 (SA) pilot valve, AC200V
-D4B 12 (SB) pilot valve, DC24V
-A1B 12 (SB) pilot valve, AC100V
-A2B 12 (SB) pilot valve, AC200V
Port isolator
Only 1 port isolator can be used on the same manifold.
PB -SP Port isolator for P port
Block-off plate (single unit)
PB-BP q
qEnvironmental protection Note
Blank Standard
Plate
PB -P
-P
Plate
（with 1 gasket）
IP65 or equivalent
(Note: Non-plug-in type is compatible with IP65 or
equivalent as standard)
PB Series Additional Parts Order Codes
Safe block (single part)
Can be mounted on the same
valve station.
Dustproof conduit cap (IP67)
Serial transmission block (single part)
PB -FS1 Dustproof conduit cap (G1/2) for
YS4 q
serial transmission block
Applicable cable outer diameter
φ8.5 [0.335in.]〜φ12.5 [0.492in.]
PB-H q w
(with 2 mounting screws) Note
qPiping direction wValve specification
T Front surface piping
U Top surface piping
-FT2 Dustproof conduit cap (G3/4) for
terminal block
Applicable cable outer diameter
φ16.5 [0.650in.]〜φ18.5 [0.728in.]
2 2-position
3 3-position
(Notes: 1. Mounting screw length will vary according
to the specification.
2. Piping block is not included.)
Individual air supply and exhaust spacer (single part)
Wiring block (single part)
PB q
w
e
Cannot function as an individual air
supply and exhaust spacer alone. It
functions only when used in combination with the special dedicated valve
□ Z). Since the spacer requires
(PB24□
additional 1 station from the existing
units, pay attention to the maximum
number of units allowed on the
manifold.
qSpecification
PB-Z q w e
-01
qPiping direction
wPiping size
T Front surface piping
U Top surface piping
1 Rc1/8
2 Rc1/4
3 Rc3/8
eEnvironmental protection Note
-TL For left-side mounting of terminal block box
-TR For right-side mounting of terminal block box
-DL For left-side mounting of D-sub connector
-DR For right-side mounting of D-sub connector
wTotal number of coils used (enter only for D-sub connector)
⁝
-20
eEnvironmental protection
Note
Blank Standard
-P
IP65 or equivalent (Note: Available in -TL and -TR only)
Blank Standard
-P
IP65 or equivalent
(Note: Available only for the terminal block box and serial
transmission type. The non-plug-in type is
compatible with IP65 or equivalent as standard.)
Cable assembly
PB q
w
qSpecification
PB -K1L Cable assembly length for D-sub
-K3L Cable assembly length for D-sub
Cable 3000mm [118in.]
-K5L Cable assembly length for D-sub
Cable 5000mm [197in.]
-EN End block for non-plug-in
type
(one set of left and right)
-EK End block for cable
specification
(one set of left and right)
-ETL End block for left-side
mounting of D-sub connector,
terminal block box and serial
transmission
(one set of left and right)
-ETR End block for right-side
mounting of D-sub connector,
terminal block box and serial
transmission
(one set of left and right)
e
qTransmission block specifications
01
02
11
21
31
32
41
42
51
52
61
71
81
A1
A2
B1
C1
D1
For UNI-WIRE System (16 outputs)
For UNI-WIRE System (8 outputs)
For Mitsubishi Electric MELSECNET/MINI-S3
For OMRON SYSBUS Wire System
For OMRON B7A Link Terminal (Standard)
For OMRON B7A Link Terminal (High speed)
For KOYO ELECTRONICS INDUSTRIES SA Bus (16 outputs)
For KOYO ELECTRONICS INDUSTRIES SA Bus (8 outputs)
For SUNX S-LINK (16 outputs)
For SUNX S-LINK (8 outputs)
For Mitsubishi Electric MELSEC I/O LINK
For Fuji Electric FA Components & Systems T Link Mini
For KEYENCE KZ-R
For OMRON CompoBus/S (16 outputs)
For OMRON CompoBus/S (8 outputs)
For Mitsubishi Electric CC-Link
For OPCN-1 (former JPCN-1)
For DeviceNet (CompoBus/D)
wMounting position eEnvironmental protection
L Left-side mounting Blank Standard
R
Right-side mounting -P
IP65 or equivalent
For details, see p.697.
Cable 1500mm [59in.]
End block set
w
Wiring base assembly
Use this when adding plug-in type or serial
transmission type valves. Includes a plug-in base
and relating lead wires and cables.
Connection rod
Use when adding or subtracting valve units.
Example: To add 2 valve units, enter PB-RZ-02.
To subtract 2 units from the 6-unit
manifold, enter PB-RS-04, and replace
the connection rods for 6 units with the
one for 4 units.
PB q
w
qParts content
wNumber of unit
-RZ Connection rod
-01
for expansion
PB-V q w e
-RS Connection rod
qWiring specification
Valve-side nameplate
T1 For adding to 8 units or less of terminal block box or serial transmission type
T2 For adding to 9 units or more of terminal block box or serial transmission type
D1 For adding to 8 units or less of D-sub connector specification
D2 For adding to 9 units or more of D-sub connector specification
K1 For adding cable specification (700mm [27.6in.])
K2 For adding cable specification (1500mm [59in.])
K3 For adding cable specification (3000mm [118in.])
⁝
-16
A plastic sheet used for sticking seals to, or placing
paper on, and showing the name of the valve
function. For mounting, insert it so that it fits into
the upper and lower grooves.
PB-M q
wEnvironmental protection Note
wWiring connection specification
Nameplate (valve side)
40 [1.57]×(Pitch 24 [0.94]×
No. of units) mm [in.]
Transparent
qNumber of units
Blank Standard
Blank Single wiring
-01
-P
IP65 or equivalent
(Note: Available only for the terminal block box and serial
transmission type. The non-plug-in type is
compatible with IP65 or equivalent as standard.)
Piping block (single part)
PB -B1 Piping block Rc1/8
-B2 Piping block Rc1/4
-B3 Piping block Rc3/8
（with 1 gasket）
D
Double wiring
eEnvironmental protection Note
Blank Standard
-P
IP65 or equivalent (Note: Available in -T1 and -T2 only)
⁝
-16
Nameplate for terminal block box
PB -MT Nameplate
(for terminal block
box) 71×83mm
[2.80×3.27in.]
Transparent
PB Series Plug-In Type Pin (Terminal) Locations by Wiring Specification (Top View)
●D-sub connector JIS-specified pin locations
●Terminal block box (21 terminals, M3 screw)
(maximum number of control pins: 20)
(maximum number of control pins: 20)
3
1
1
2
3
4
5
6
7
8
9
10 11 12 13
2
5
4
7
6
9
8
11
10
13
12
15
14
19 COM
17
16
18
20
14 15 16 17 18 19 20 21 22 23 24 25
1〜20 : Control terminals
COM : Common terminal
1〜10, 14〜23: Control pins
24, 25: COM pins (shorted within the wiring block)
Cautions: 1. Since the DC24V specification has no polarity, it
can be used for either positive common or negative
common.
2. For the mounting screw, use M2.6.
Cautions: 1. Set the tightening torque for the terminal screw (M3) at 49.0N･cm
{5.0kgf･cm} [4.3in･lbf] or less.
2. Use crimping terminals of 6.2mm [0.244in.] or less for both the
round terminal and the Y-shaped terminal.
●A dedicated cable assembly is available.
For details, see p.697.
6.2 or below
Detailed Diagrams for Wiring Systems
6.2 or below
※ For the relationship between the pin No. (terminal No.) and the corresponding solenoids,
see p.694.
●D-sub connector
●Terminal block box
24,25（COM）
COM
1
1
Solenoid
Solenoid
1〜10
14〜23
n
20
Solenoid
Solenoid
At-a-glance Guide for Maximum Number of Control Solenoids in Plug-in Type & Serial Transmission Type Manifolds
This is an at-a-glance guide for the maximum number of control solenoids by wiring specifications for the plug-in and serial transmission types.
When ordering a manifold, ensure that the number of solenoid valves does not exceed the maximum number of control solenoids in the table below.
Cautions: 1. For the cable outlet on top surface types, the maximum number of the units for the valve and block-off plate is 12 units, due to the cable bending space.
2. The individual air supply and exhaust spacer occupies 1 unit space. Ensure that the total number of units does not exceed 16 units.
最大連数
Wiring specification &
transmission block specification
結線仕様
Maximum number of
control solenoids ダブル配線
（-D） 詰め配線
（無記入）
-U□：Cable top surface outlet type
24
12連
12連
-E□：Cable side surface outlet type
32
16連
16連
-D□□：D-sub connector（25P）
20
10連
-T□：Terminal block box（21 terminals）
20
10連
-01：For UNI-WIRE System (16 outputs)
16
8連
-02：For UNI-WIRE System (8 outputs)
8
4連
-11：For Mitsubishi Electric MELSECNET/MINI-S3
16
8連
-21：For OMRON SYSBUS Wire System
16
8連
-31：For OMRON B7A Link Terminal (Standard)
16
8連
-32：For OMRON B7A Link Terminal (High speed)
16
8連
-41：For KOYO ELECTRONICS INDUSTRIES SA Bus (16 outputs)
16
8連
-42：For KOYO ELECTRONICS INDUSTRIES SA Bus (8 outputs)
8
4連
-51：For SUNX S-LINK (16 outputs)
16
8連
-52：For SUNX S-LINK (8 outputs)
8
4連
-61：For Mitsubishi Electric MELSEC I/O LINK
16
8連
-71：For Fuji Electric FA Components & Systems T Link Mini
16
8連
-81：For KEYENCE KZ-R
16
8連
-A1：For OMRON CompoBus/S (16 outputs)
16
8連
-A2：For OMRON CompoBus/S (8 outputs)
8
4連
-B1：For Mitsubishi Electric CC-Link
16
8連
-C1：For OPCN-1 (former JPCN-1)
16
8連
-D1：For DeviceNet (CompoBus/D)
16
8連
シングルソレノイド、ダブル
ソレノイド、ブロックプレート
の搭載数により異なります。
制御するソレノイドの数が
最大制御ソレノイド点数以
下になるように連数を指定
してください。
なお、全体の連数が16連
を超える指定はできません。
Serial Transmission Block, Terminal Block (LED) Names
●For DeviceNet (OMRON CompoBus/D)
Transmission block specification: -D1
Dip switch for various settings
NS
1
2
3
4
5
6
7
8
9
0
O
N
MS
Communication connector
Power supply connector
LED indicator
Indicator
State
Lights up
Color
Green
•No setting state
Flashing
MS
Lights up
Red
•Serious breakdown
Flashing
•Minor breakdown
Shuts off
•No power supply
Lights up
Green
Flashing
NS
Description
•Normal state
Lights up
•Communication connection completed
•No communication connection
Red
•Serious communication fault
Flashing
•Minor communication fault
Shuts off
•No power supply
Remarks
※Conforms to DeviceNet (CompoBus/D)
● Number of outputs per block
Maximum of 16 solenoids
● Related materials: User’s Manual, Document No.HV029
Cable Assembly
● Cable assembly for D-sub
PB-K1L (Cable length L: 1500mm [59in.])
PB-K3L (Cable length L: 3000mm [118in.])
PB-K5L (Cable length L: 5000mm [197in.])
L
（300）
M2.6×0.45
25
24
23
22
21
20
19
18
17
16
15
14
Label
（20）
AWG28
13
12
11
10
9
8
7
6
5
4
3
2
1
（Connector no.）
(B side)
(A side)
A side
B side
Connector No.
q
w
e
r
t
y
u
i
o
!0
Label No.
1
2
3
4
5
6
7
8
9
10
!1
!2
!3
!4
!5
!6
!7
!8
!9
@0
@1
@2
@3
11
12
13
14
15
16
17
18
19
20 COM COM
@4
@5
PB Series Dimensions of Non-Plug-In Type (mm)
PBM□N
Front surface piping
41
6
24
24
（Pitch）
46
20
LED indicator
10.5
（18）
mPm
（6）
P
Rc1/8 external pilot port
(with 1 plug)
7
Unit Dimensions
L
13
Manual override
cover
6.5
4-R3.25
12
P2
4A
4A
P
1
40
28
77.5
39
139
4A
5
R1
41
27
C
L
O
S
E
28
7
88
42
163
4A
R2
3
2B
2B
2B
2B
1
P
7
O
P
E
N
20
6.5
20
PB-M□
(Nameplate)
16
Number of units
L
1
92
P
80
2
116
104
3
140
128
4
164
152
5
188
176
6
212
200
7
236
224
8
260
248
9
284
272
10
308
296
11
332
320
12
356
344
13
380
368
14
404
392
15
428
416
16
452
440
Stn.1 Stn.2 Stn.3 Stn.4
PB24C5-T2-G2
PB24HC6-T3-39 PB24C7-T3-G1
R2
3
1
P
P
1
5
R1
8-Rc1/2
(with 5 plugs)
28
6
20
2（B）port
17
37
25
60
18
63.6
PB24C5-T2-G1
20
4（A）port
34
PBM□N
Top surface piping
41
6
Number of units
L
1
92
80
LED indicator
2
116
104
Manual override
cover
3
140
128
4
164
152
5
188
176
6
212
200
7
236
224
8
260
248
9
284
272
10
308
296
11
332
320
12
356
344
13
380
368
4（A）port
14
404
392
2（B）port
15
428
416
16
452
440
24
46
24
（Pitch）
20
10.5
（18）
mPm
（6）
P
Rc1/8 external pilot port
(with 1 plug)
7
Unit Dimensions
L
13
4-R3.25
6.5
20
12
4A
4A
3
5
2B
2B
2B
2B
1
28
39
R2
1
R1
P
41
31.5
P
27
25
88
77.5
C
L
O
S
E
28
4A
132
135.6
4A
7
42
159.6
P2
O
P
E
N
20
20
16
Stn.1 Stn.2 Stn.3 Stn.4
PB24C5-U2-G2
PB24HC6-U3-39 PB24C7-U3-G1
P
1
1
P
5
R1
28
3
8-Rc1/2
(with 5 plugs)
20
PB-M□
(Nameplate)
20
34
17
37
R2
6
40
60
PB24C5-U2-G1
67
6.5
P
PB Series Dimensions of Plug-In Type (mm)
PBM□P-UL
Cable outlet type
Top surface piping
2
4-G3/4
Cable top surface outlet at the left (-UL)
37
With 3 wiring outlets
External pilot port
(with 1 plug)
18
17
2
P
6
24
LED indicator
Rc1/8
L
Manual override
cover
24
（Pitch）
Unit Dimensions
46
17
18
4-R3.25
6.5
001
002
Number of unit
12
4A
4A
4A
4A
R2
3
5
2B
2B
2B
2B
1
R1
P
41
1
27
P
28
39
159.6
135.6
132
77.5
31.5
25
C
L
O
S
E
28
7
42
99.5
P2
O
P
E
N
20
20
4（A）port
6.5
16
2（B）port
Stn.1 Stn.2 Stn.3 Stn.4
PB24C5-U2
P
80
2
116
104
3
140
128
4
164
152
5
188
176
6
212
200
7
236
224
8
260
248
9
284
272
10
308
296
11
332
320
12
356
344
13
380
368
14
404
392
15
428
416
16
452
440
6
R2
3
P
1
1
P
5
R1
PB-M□
(Nameplate)
20
28
1
92
37
P
PB24C7-U3
17
3
L
1
Note: Cable top surface outlets
accommodates maximum of 12
units.
PB24HC6-U3
PB24C5-U2
40
R2
67
●Side surface left outlet: -EL
60
8-Rc1/2
(with 5 plugs)
Number of units
20
34
PBM□P-UL
Cable outlet type
Front surface piping
37
With 3 wiring outlets
2
4-G3/4
L
Cable top surface outlet at the left (-UL)
24
LED indicator
Rc1/8
External pilot port
(with 1 plug)
18
2
P
17
Manual override
cover
Unit Dimensions
6
24
（Pitch）
46
17
18
4-R3.25
6.5
001
002
Number of unit
4A
4A
4A
4A
P
1
40
28
77.5
39
132
139
163
12
5
R1
41
27
C
L
O
S
E
28
7
42
R2
3
2B
2B
2B
2B
1
P
7
O
P
E
N
20
6.5
20
PB-M□
(Nameplate)
16
Stn.1 Stn.2 Stn.3 Stn.4
PB24C5-T2
1
PB24C7-T3
6
R2
3
1
P
P
1
5
R1
20
2（B）port
4（A）port
20
34
28
P
PB24C5-T2
L
1
92
P
80
2
116
104
3
140
128
4
164
152
5
188
176
6
212
200
7
236
224
8
260
248
9
284
272
10
308
296
11
332
320
12
356
344
13
380
368
14
404
392
15
428
416
16
452
440
Note: Cable top surface outlets
accommodates maximum of 12
units.
17
3
18
R2
8-Rc1/2
(with 5 plugs)
63.6
60
25
●Side surface left outlet: -EL
PB24HC6-T3
37
99.5
P2
Number of units
PBM□P-TL
Terminal block box
Front surface piping
Unit Dimensions
4
1
L2
LED indicator
-P：IP65
External pilot port
(with 1 plug)
Rc1/8
4-R3.25
L1
P
Manual override
cover
24
6
24
（Pitch）
46
4
6.5
2
6
Standard
Standard
2
12
P2
4A
4A
2B
2B
2B
2B
1
P
41
28
39
3
R1
-P：IP65
7
O
P
E
N
6
O
S
E
R2
5
27
1
40
P
PB-MT: Nameplate
（Option）71×83
L1
L2
1
92
166
P
80
2
116
190
104
3
140
214
128
4
164
238
152
5
188
262
176
6
212
286
200
7
236
310
224
8
260
334
248
9
284
358
272
10
308
382
296
11
332
406
320
12
356
430
344
13
380
454
368
14
404
478
392
15
428
502
416
16
452
526
440
4A
114
77.5
132
139
163
4A
Number of units
20
20
PB-M□
(Nameplate)
Stn.1 Stn.2 Stn.3 Stn.4
74
PB24C5-T2-B
20
PB24HC6-T3-B
PB24C5-T2-B
PB24C7-T3-B
3
1
P
P
1
5
R1
1
37
60
R2
18 25
17 28
37
60
63.6
6
32
（Width across
flats）
2-G3/4
(Cable outlet port)
8-Rc1/2
(with 5 plugs)
2（B）port
20
20
4（A）port
34
PBM□P-DEL
D-sub connector
Front surface piping
L2
2
LED indicator
L1
Manual override cover
P
Rc1/8 External pilot port
(with 1 plug)
24
Unit Dimensions
6
24
（Pitch）
46
6.5
4-R3.25
P2
12
4A
4A
4A
3
2B
2B
2B
2B
1
28
R1
P
41
5
7
O
P
E
N
9
O
S
E
R2
1
27
P
40
39
114
77.5
132
139
57
163
4A
20
20
PB-M□
(Nameplate)
Stn.1 Stn.2 Stn.3 Stn.4
PB24C5-T2-B
51
7 9
PB24C5-T2-B
PB24HC6-T3-B
PB24C7-T3-B
6
R2
3
1
P
P
1
5
R1
8-Rc1/2
(with 5 plugs)
20
2（B）port
4（A）port
20
34
18 25
17 28
37
60
63.6
46
1
60
（67）
Top surface and left side mounting case
-DUL
Number of units
L1
L2
1
92
138
P
80
2
116
162
104
3
140
186
128
4
164
210
152
5
188
234
176
6
212
258
200
7
236
282
224
8
260
306
248
9
284
330
272
10
308
354
296
11
332
378
320
12
356
402
344
13
380
426
368
14
404
450
392
15
428
474
416
16
452
498
440
PB Series Dimensions of Serial Transmission Type (mm)
PBM□S
Front surface piping
5
Rc1/8
External pilot port
(with 1 plug)
L2
2
LED indicator
L1
Manual override
cover
P
24
Unit Dimensions
6
24
（Pitch）
46
4
Standard
4A
4A
4A
2B
2B
2B
2B
1
R1
P
-P：IP65
41
28
39
3
5
7
O
P
E
N
9
O
S
E
R2
1
27
P
40
114
4A
YS401 L
142649
24V OV
77.5
G
132
12
ADDRESS
1 2 4 8 163264128
D
139
P2
L1
L2
1
92
166
P
80
2
116
190
104
3
140
214
128
4
164
238
152
5
188
262
176
6
212
286
200
7
236
310
224
8
260
334
248
9
284
358
272
10
308
382
296
11
332
406
320
12
356
430
344
13
380
454
368
14
404
478
392
15
428
502
416
16
452
526
440
SEND
24V OV
163
POWER
G
40
D
MADE IN JAPAN
6.5
4-R3.25
Number of units
20
20
PB-M□
(Nameplate)
Serial transmission block
(Panel design varies according to transmission block specifications.)
74
Stn.1 Stn.2 Stn.3 Stn.4
26
PB24C5-T2-B
PB24C5-T2-B
PB24HC6-T3-B
PB24C7-T3-B
3
1
P
P
1
5
R1
8-Rc1/2
(with 5 plugs)
20
2（B）port
4（A）port
20
34
18 25
17 28
37
60
63.6
R2
1
53
79
6
PB Series Dimensions of Mounted Valve (mm)
Remark: Diagrams show the wiring specification grommet type L connector: -G2.
5-port, 2-position
PB24□C5
PB24□C6
18
25
60
63.6
1.4
1.5
56
（300） 43
●Piping specification: Front surface piping（-T□）
21
24
139
●Piping specification: Top surface piping（-U□）
2-Rc3/8（Rc1/4, 1/8）
135.6
67
25
60
75.5
24
5-port, 3-position
PB24□C7
PB24□C8
PB24□C9
18
25
60
63.6
1.4
1.5
21
24
163
●Piping specification: Top surface piping（-U□）
2-Rc3/8（Rc1/4, 1/8）
159.6
25
60
75.5
67
56
（300） 43
●Piping specification: Front surface piping（-T□）
24
PB Series Dimensions of Options (mm)
●Block-off plate（PB-BP□）
●Individual air supply and exhaust spacer（PB-Z□）
24
（Pitch）
46
24
（Pitch）
12
1
R2
3
2B
PB-Z□
Individual air supply
and exhaust spacer
4A
5
R1
P
1
1
P
R2
3
2B
24
5
R1
1
P
3
1
P
P
1
5
R1
60
R2
63.6
24
60
P
12
P2
PB-BP
Block-off plate
4A
R2
3
1
P
P
1
5
R1
63.6
P2
46
1（P）port
3, 5（R）port
Piping specification: Front surface piping（-T□）
1
R2
3
2B
2B
5
R1
1
P
4A
132
135.6
4A
P
1
R2
3
2B
2B
5
R1
1
P
61.3
159.6
132
4A
37.3
P
12
P2
4A
186
Piping specification: Top surface piping（-U□）
12
P2
210
●Safe block
7
Residual pressure exhaust
manual override
For PB24□C7, C8, C9
（3 positions）
For PB24□C7, C8, C9
（3 positions）
Residual pressure exhaust
manual override
7
60
R2
3
1
P
60
63.6
114
For PB24□C5, C6
（2 positions）
For PB24□C5, C6
（2 positions）
37.3
●Safe block
P
1
5
R2
3
1
P
P
1
5
R1
R1
2（B）port
4（A）port
●Dustproof conduit cap: For serial transmission（-FS1）
●Dustproof conduit cap: For terminal block box（-FT2）
D
POWER
G
12
P2
12
4A
D
ADDRESS
1 2 4 8 163264128
24V OV
SEND
MADE IN JAPAN
P2
G
1
R2
3
2B
2B
P
1
R2
3
4A
4A
2B
2B
29.5 6
（MAX）
36.5
（MAX）
YS401 L
142649
24V OV
P
4A
26
Applicable cable outer diameter
φ8.5〜12.5
20
Applicable cable outer diameter
φ16.5〜18.5
">