Koganei PBSAL Single acting non-rotating push out type Instruction manual
The Koganei PBSAL is a single-acting non-rotating push-out type air cylinder designed for reliable and efficient operation. This cylinder features a variety of mounting options, including basic, single foot, double foot, and flange types. It has a robust construction with a high-quality piston seal and rod seal. The cylinder is capable of operating at a pressure range of 0.34 to 0.7 MPa and a temperature range of 0 to 60 °C. The PBSAL also includes a cushion mechanism to reduce impact noise during high-speed operations.
PDF
Download
Document
Advertisement
Advertisement
BK-UC003 Ver.1.0 Air Cylinder PEN CYLINDER INSTRUCTION MANUAL Ver.1.0 Handling Instructions and Precautions General precautions Mounting Tighten the mounting nuts to the recommended tightening torques shown below. Thread size mm Recommended tightening torque N·cm [in·lbf] M6×1 240 [21] M8×1 600 [53] M10×1 1200 [106] Piping to single acting type cylinders Piping directly to single acting type cylinders for air supply can cause the unit to exceed the speed range, and damage the cylinder. Always use a speed controller with meter-in control to ensure that the speed range can ensure the allowable kinetic energy or less. Media 1. Always thoroughly blow off (use compressed air) the tubing before piping. Entering chips, sealing tape, rust, etc., generated during piping work could result in air leaks or other defective operation. 2. Use air for the media. For the use of any other media, consult us. 3. Air used for the cylinder should be clean air that contains no deteriorated compressor oil, etc. Install an air filter (filtration of a minimum 40 µm) near the cylinder or valve to remove collected liquid or dust. In addition, drain the air filter periodically. Collected liquid or dust entering the cylinder may cause improper operation. Lubrication The product can be used without lubrication, if lubrication is required, use Turbine Oil Class 1 (ISO VG32) or equivalent. Avoid using spindle oil or machine oil. Atmosphere If using in locations subject to dripping water, dripping oil, etc., or to large amounts of dust, use a cover to protect the unit. Cylinder Thrust Select a suitable bore size considering the load and air pressure to obtain the required thrust. Since the figures in the table are calculated values, select a bore size that results in a load Load ratio (load ratio = ) of 70% or less (50% or less for high speed application). Calculated value Pull Push N [lbf.] Bore size mm [in.] Piston rod diameter mm [in.] 2.5 [0.098] 4 [0.157] 1 [0.039] 2 [0.079] 6 [0.236] 3 [0.118] 10 [0.394] 4 [0.157] 16 [0.630] 5 [0.197] Pressure area mm2 [in.2] Operation type Single acting push type Single acting push type Single acting push type Single acting pull type Push side Double acting type Pull side Single acting push type Single acting pull type Push side Double acting type Pull side Single acting push type Single acting pull type Push side Double acting type Pull side 4.9 [0.0076] 12.6 [0.0195] 28.3 [0.0439] 21.2 [0.0329] 28.3 [0.0439] 21.2 [0.0329] 78.5 [0.1217] 66 [0.102] 78.5 [0.1217] 66 [0.102] 201 [0.312] 181 [0.281] 201 [0.312] 181 [0.281] Air pressure MPa [psi.] 0.1 [15] 0.2 [29] 0.3 [44] 0.4 [58] 0.5 [73] ― ― ― 0.8 [0.18] 1.3 [0.29] ― ― ― 2.2 [0.49] 3.5 [0.79] ― ― 7.8 [1.75] 10.7 [2.41] 5.0 [1.12] ― ― 5.0 [1.12] 7.1 [1.60] 2.9 [0.65] ― 5.7 [1.28] 8.5 [1.91] 11.3 [2.54] 14.2 [3.19] ― 8.5 [1.91] 10.6 [2.38] 4.2 [0.94] 6.4 [1.44] ― 9.8 [2.20] 17.7 [3.98] 25.5 [5.73] 33.4 [7.51] ― 7.3 [1.64] 13.9 [3.12] 20.5 [4.61] 27.1 [6.09] 7.9 [1.78] 15.7 [3.53] 23.6 [5.31] 31.4 [7.06] 39.3 [8.83] 6.6 [1.48] 13.2 [2.97] 19.8 [4.45] 26.4 [5.93] 33.0 [7.42] 30.4 [6.83] 50.5 [11.35] 70.6 [15.87] 90.7 [20.39] ― 26.4 [5.93] 44.5 [10.00] 62.6 [14.07] 80.7 [18.14] ― 20.1 [4.52] 40.2 [9.03] 60.3 [13.56] 80.4 [18.07] 100.5 [22.59] 18.1 [4.07] 36.3 [8.16] 54.3 [12.21] 72.4 [16.28] 90.5 [20.34] 0.6 [87] 1.7 [0.38] 4.8 [1.08] 13.5 [3.03] 9.2 [2.07] 17.0 [3.82] 12.7 [2.85] 41.2 [9.26] 33.7 [7.58] 47.1 [10.59] 39.6 [8.90] 110.8 [24.91] 98.8 [22.21] 120.6 [27.11] 108.6 [24.41] 0.7 [102] 2.2 [0.49] 6.0 [1.35] 16.3 [3.66] 11.3 [2.54] 19.8 [4.45] 14.8 [3.33] 49.1 [11.04] 40.3 [9.06] 55.0 [12.36] 46.2 [10.39] 130.9 [29.43] 116.9 [26.28] 140.7 [31.63] 126.7 [28.48] Allowable Kinetic Energy Pen cylinders include a cushioning mechanism. This mechanism is intended to reduce as much as possible the impact of pistons with high kinetic energy when they stop at the end of the stroke. There are 2 types of cushions, as shown below. Rubber bumper (Graph 1) 50 ●Rubber bumpers (Standard equipment) 10 Load (kg) Rubber bumpers installed on both sides of the piston soften the impact at the end of the stroke, and absorb the impact noise during stopping, in response to high-frequency and high-speed operations. Note that a certain amount of rebound will occur at the end of the stroke on the cylinder with the rubber bumpers. 5 φ16 φ10 φ6 1 0.5 ●Variable cushions Use variable cushions for large load or high-speed operations that rubber bumpers cannot adequately absorb. The impact is absorbed by compressing air, when the piston stops at the end of the stroke. Since the cushioning stroke is included within the cylinder stroke, be careful to ensure that the cushioning is not performed excessively during cylinder applications of 25mm strokes or less. An excessive cushioning can result in too much time for each stroke, reducing efficiency. When operated at or below the absorbable kinetic energy shown in the table below, the cushion seal life is 1 million operations or more. The kinetic energy of load can be obtained through the formulas shown below. W Ex = m 2 E' x= 2g ' 2 2 Ex : Kinetic energy (J) E'x: Kinetic energy [ft・lbf] m : Load mass (kg) W: Load [lbf.] ' : Piston speed [ft./sec.] : Piston speed (m/s) v 0.5 50 100 500 1000 Maximum operating speed (mm/s) 1kg = 2.205 lb. 1mm/s = 0.0394 in./sec. Variable cushion (Graph 2) 500 v v g : Acceleration of gravity 32.2 [ft./sec.2] Operating speed range 100 Load (kg) v 0.1 50 φ16 10 φ10 5 ●Rubber bumper・・・・・・・・・・・・・・・・50〜750mm/s [2.0〜29.5in./sec.] ●Variable cushion ・・・・・・・・・・・・・・100〜1000mm/s [3.9〜39.4in./sec.] 1 J [ft·lbf] 0.5 Allowable kinetic energy Bore size mm [in.] With rubber bumpers 6 [0.236] 0.009 [0.0066] ― 10 [0.394] 0.015 [0.011] 0.07 [0.052] 16 [0.630] 0.04 [0.030] 0.18 [0.133] With variable cushion 50 100 500 1000 Maximum operating speed (mm/s) 1kg = 2.205 lb. 1mm/s = 0.0394 in./sec. How to read graphs From Graph 1, φ16 [0.630in.] with rubber bumpers is selected where the load is 1kg [2.2lb.] and the maximum operating speed is 90mm/s [3.54in./sec.]. From Graph 2, φ16 [0.630in.] with variable cushion is selected where the load is 2kg [4.4lb.] and the maximum operating speed is 400mm/s [15.7in./sec.]. PEN CYLINDERS Double Acting Type, Single Acting Push Type, Single Acting Pull Type Symbols ●Double acting type ●Single acting push type ●Single acting pull type Specifications Item Operation type Bore Size and Stroke Bore size mm [in.] ●Double acting type 6 [0.236] 10 [0.394] 16 [0.630] Bore size Double acting type, Single acting push type, Single acting pull type Media mm [in.] Maximum Stroke available tolerance stroke Standard strokes Note Air Mounting type Basic type, Foot type, Flange type, Clevis type (clevis type of φ10 and φ16 only) 6 Operating pressure range Note1 MPa [psi.] 0.12〜0.7 [17〜102] 10 Proof pressure MPa [psi.] Operating temperature range 0.06〜0.7 [9〜102] 1.05 [152] °C [°F] 16 0〜70 [32〜158] Operating speed range mm/s [in./sec.] Cushion 0.08〜0.7 [12〜102] Rubber bumper Lubrication Not required Port size M5×0.8 Note 2 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 Operation type Bore size Single acting push type 10 16 mm [in.] Standard strokes Note 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 Maximum available stroke 75 105 120 6 10 +1.5 +0 +0.059 [ +0 ] 200 75, 100, 125, 150, 175, 200 Single acting pull type 5, 10, 15, 20, 25, 30 16 30 Stroke tolerance +1.5 +0 +0.059 [ +0 ] +1.5 +0 +0.059 [ +0 ] Note: For non-standard strokes: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, collar packed to the next size up stroke of cylinder. Order Codes 10×30 − − − − − Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet Rod end accessory Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● For bore sizes of φ10 and φ16 only. ● As for the cylinder joints and the cylinder rod ends, order separately. Operation type DA Double acting type SA Single acting push type TA Single acting pull type Pen cylinder series Head cover piping specification Blank Axial direction piping A Lateral piping (Not available for clevis mounting type and single acting pull type) M Lateral piping with mounting thread ※ ※ -M corresponds only to φ10 and φ16 of double acting type and single acting push type. Not available for clevis mounting type. ( 150 75, 100, 125, 150 6 Notes: 1. For details of each cylinder’s operation type, see the table for the minimum operating pressure. 2. M3 × 0.5 can also be selected at φ6 only. PB 100 ●Single acting type 50〜750 [2.0〜29.5] None 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 ) Mounting type (Included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only onφ10 and φ16 of head cover -M specification double acting type and -M specification single acting push type) 1A Single foot mounting type 3 Flange mounting type 7 Clevis mounting type (with pin for bore sizes of φ10 andφ16 only) 7-7C Clevis mounting type with pin and clevis supporting bracket (For bore sizes of φ10 and φ16 only) Connection port Blank M5×0.8 (φ6, φ10, φ16) M3 M3×0.5 (φ6 only) Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Lead wire length A 1000mm [39in.] B 3000mm [118in.] Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Minimum Operating Pressure Minimum operating pressure MPa [psi.] Mounting type 6 [0.236] 0.12 [17] 1 Double foot type Included at shipping 10 [0.394] 0.08 [12] 1A Single foot type Note Included at shipping 16 [0.630] 0.06 [9] 3 Flange type Included at shipping 6 [0.236] 0.3 [44] 7 Clevis type (with pin) Assembled and shipped Clevis type with supporting bracket (with pin) Supporting bracket included at shipping Operation type Bore size mm [in.] Double acting type Single acting push type 10 [0.394] 7-7C 0.15 [22] 16 [0.630] 6 [0.236] Single acting pull type Mounting type Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. 0.35 [51] 10 [0.394] Remark Name 0.15 [22] 16 [0.630] Mass Single acting pull type Single acting push type Double acting type Operation type g [oz.] Mounting Bore type mm Basic type Additional mass Stroke mm 5 10 15 20 25 30 35 40 45 50 Mounting type 55 60 75 100 125 150 175 ‐M − − − 6 − − 10 20.3 21.5 22.6 23.8 24.9 26 27.2 28.3 29.5 30.6 31.7 32.9 34 35.2 36.3 37.4 − [0.716] [0.758] [0.797] [0.840] [0.878] [0.917] [0.959] [0.998] [1.041] [1.079] [1.118] [1.160] [1.199] [1.242] [1.280] [1.319] − 5 7 [0.25] [0.18] − 1 [0.04] 6 2 [0.07] [0.21] 16 38.5 40.3 42.1 43.9 45.7 47.5 49.3 51.1 52.9 54.7 56.5 58.3 60.1 61.9 63.7 65.5 67.3 69.1 12 18 [1.358] [1.422] [1.485] [1.549] [1.612] [1.675] [1.739] [1.802] [1.866] [1.929] [1.993] [2.056] [2.120] [2.183] [2.247] [2.310] [2.374] [2.437] [0.63] [0.42] − 2 [0.07] 8 3 [0.11] [0.28] 9.6 10.2 10.8 13.9 14.5 15 16.5 17.1 17.6 18.3 18.9 19.4 − [0.339] [0.360] [0.381] [0.490] [0.511] [0.529] [0.582] [0.603] [0.621] [0.646] [0.667] [0.684] − − − − − − − − − − 32 [1.13] 1 [0.04] − − − − 45 [1.59] 2 [0.07] − − − 0.5 [0.018] − − 6 2 [0.07] [0.21] 5 7 [0.25] [0.18] 18.9 20 21.1 24 25.1 26.2 31.4 32.5 33.6 34.8 35.9 37 10 − [0.667] [0.705] [0.744] [0.847] [0.885] [0.924] [1.108] [1.146] [1.185] [1.228] [1.266] [1.305] − − − − − 5 7 [0.25] [0.18] − 1 [0.04] 39 40.8 42.5 47.7 49.5 51.2 61 62.8 64.5 66.3 68.1 69.8 [1.376] [1.439] [1.499] [1.683] [1.746] [1.806] [2.152] [2.215] [2.275] [2.339] [2.402] [2.462] − − − − − − 12 18 [0.63] [0.42] − 2 [0.07] − − − − − − − 1 32 [1.13] [0.04] − − − − − − − − − 2 45 [1.59] [0.07] − − 16 20.9 24 25.1 27.9 29.1 30.2 35.4 36.5 37.6 38.8 39.9 41 10 Clevis [0.737] [0.847] [0.885] [0.984] [1.026] [1.065] [1.249] [1.287] [1.326] [1.369] [1.407] [1.446] − mounting type 50 51.8 53.5 58.7 60.5 62.2 72 73.8 75.5 77.3 79.1 80.8 16 (with pin) [1.764] [1.827] [1.887] [2.071] [2.134] [2.194] [2.540] [2.603] [2.663] [2.727] [2.790] [2.850] − A: 20 [0.71] B: 50 [1.76] 8 3 [0.11] [0.28] 6 11.6 12.2 12.8 15.8 16.4 16.9 − [0.409] [0.430] [0.451] [0.557] [0.578] [0.596] − − − − − − − − − − − 7 5 [0.25] [0.18] − 0.5 [0.018] − − 10 21 22.6 24.1 27 28.1 29.2 − [0.741] [0.797] [0.850] [0.952] [0.991] [1.030] − − − − − − − − − − − 7 5 [0.25] [0.18] − 1 [0.04] − − 16 41.7 43.5 45.3 50.3 52.1 53.8 − [1.471] [1.534] [1.598] [1.774] [1.838] [1.898] − − − − − − − − − − − 18 12 [0.63] [0.42] − 2 [0.07] − − − − − − − − − − − − − − − 1 32 [1.13] [0.04] − − − − − − − − − − − − − − − 2 45 [1.59] [0.07] − − 25 26.6 28.1 31.6 32.4 33.2 10 − Clevis [0.882] [0.938] [0.991] [1.115] [1.143] [1.171] mounting type 54.5 56.3 61.3 63.1 64.8 (with pin) 16 52.7 − [1.859] [1.922] [1.986] [2.162] [2.226] [2.286] Remark : Includes mounting nut and rod end nut. For the mass of the double foot bracket, add double the mass of the single foot bracket listed above. Notes: 1. With supporting bracket and pin. 2. Same for all sensor switch models (ZC253□, ZC230□, ZC201□, ZC205□). Calculation example: The mass for 2 units of ZC253A, with a double acting type cylinder with magnet with single foot bracket, bore size of 10mm, and stroke of 45mm, is 29.5+7 + 1 + 40 =77.5g [2.734oz.]. Single Acting Type Spring Return Force N [lbf.] Bore size mm ‐A 5 7 [0.25] [0.18] 6 Basic type (1 pc.) 0.5 [0.018] 12.9 13.5 14.1 14.7 15.3 15.9 16.5 17.1 17.7 18.3 18.9 19.5 − [0.455] [0.476] [0.497] [0.519] [0.540] [0.561] [0.582] [0.603] [0.624] [0.646] [0.667] [0.688] 24.3 25.5 26.6 27.8 28.9 30 31.2 32.3 33.5 34.6 35.7 36.9 38 39.2 40.3 41.4 10 − − Clevis [0.857] [0.899] [0.938] [0.981] [1.019] [1.058] [1.101] [1.139] [1.182] [1.220] [1.259] [1.302] [1.340] [1.383] [1.422] [1.460] mounting type 62.1 63.9 65.7 67.5 69.3 71.1 72.9 74.7 76.5 78.3 80.1 60.3 56.7 54.3 58.5 53.1 51.3 49.5 (with pin) 16 [1.746] [1.810] [1.873] [1.915] [2.000] [2.063] [2.127] [2.190] [2.254] [2.317] [2.381] [2.444] [2.508] [2.571] [2.635] [2.698] [2.762] [2.825] Basic type Cylinder Sensor switch Lateral piping with Note 2 200 Single foot Flange Clevis Note 1 magnet Spring return force 5St 10St 15St 20St 25St 30St 35St 40St 45St 50St 55St 60St End of stroke 6 3.0 [0.67] 2.5 [0.56] 2.0 [0.45] 2.5 [0.56] 2.3 [0.52] 2.0 [0.45] 2.7 [0.61] 2.5 [0.56] 2.4 [0.54] 2.3 [0.52] 2.2 [0.49] 2.0 [0.46] 3.5 [0.79] 10 5.1 [1.15] 4.4 [0.99] 3.7 [0.83] 4.4 [0.99] 4.0 [0.90] 3.7 [0.83] 4.6 [1.03] 4.4 [0.99] 4.2 [0.94] 4.0 [0.90] 3.8 [0.85] 3.7 [0.83] 5.9 [1.33] 16 8.5 [1.91] 7.3 [1.64] 6.1 [1.37] 7.3 [1.64] 6.7 [1.51] 6.1 [1.37] 7.6 [1.71] 7.3 [1.64] 7.0 [1.57] 6.7 [1.51] 6.4 [1.44] 6.1 [1.37] 9.8 [2.20] Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 r !0 No. o yt u w e q i w ●Clevis mounting type (-7) w Materials Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note1 Plastic magnet u u Piston seal i i Rod seal o o Bumper Note2 !0 !0 Mounting nut !1 !1 Rod end nut Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Notes: 1. For cylinders with magnets. Standard cylinders do not have a builtin magnet for the sensor switch. 2. Not available for bore size φ6. ●Lateral piping (-A) w !0 ●Lateral piping with mounting thread (-M) CS03−10ND−A00 ●Single acting push type o r !0 q !1 e PartsCS03−10ND−A00 Materials No. !2 i yt u w w ●Clevis mounting type (-7) w CS03−10ND−A00 q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note1 Plastic magnet u u Piston seal i i Bumper Note2 o o Rod end nut !0 !0 Mounting nut !1 !1 Spring Steel !2 !2 Collar Aluminum alloy Aluminum alloy (nickel plated) CS03−10ND−A00 Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Notes: 1. For cylinders with magnets. Standard cylinders do not have a builtin magnet for the sensor switch. 2. Not available for bore size φ6. ●Lateral piping (-A) w !0 ●Lateral piping with mounting thread (-M) ●Single acting pull type !1 r !0 q i No. uy t o !2 !3 e w w ●Clevis mounting type (-7) w w Parts Materials Rod cover CS03−10ND−A00 CS03−10ND−A00 Aluminum alloy (nickel plated) Head cover CS03−10ND−A00 e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note1 Plastic magnet u u Piston seal i i Rod seal o o Bumper Note2 !0 !0 Mounting nut !1 !1 Rod end nut !2 !2 Spring Steel !3 !3 Collar Aluminum alloy q q Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Notes: 1. For cylinders with magnets. Standard cylinders do not have a builtin magnet for the sensor switch. 2. Not available for bore size φ6. Dimensions of Double Acting Type (mm) Bore size × ■Basic type PBDA PBDA Stroke Bore size A+Stroke C+Stroke 28 20 15 J N M5×0.8 Note 1 (M3×0.5) 6 ●φ6 Head cover M5×0.8 M5×0.8 Note 1 (M3×0.5) φ9 6 4 φV φU1 φU G 8 □8 L K □B Width across flats I Width across flats AY ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M PBDA ●Lateral piping (-A) Bore size × Stroke -A PBDA A+3+Stroke A+3+Stroke M5×0.8 (M3×0.5) Note1 M5×0.8 φU2 9 9 4.5 4.5 8 4 φU2 L □B1 Bore mm [in.] Code □B1 A C B B1 G I J K L N U U1 U2 V AY 6 [0.236] 77 49 12 12 14.5 5.5 2.4 M3×0.5 M6×1 10 14 − 14 3 10 10 [0.394] 71 43 12 12 13 7 3.2 M4×0.7 M8×1 8.5 14 11 14 4 12 16 [0.630] 71.5 43.5 17 17 11.5 8 4 M5×0.8 M10×1 7 19 17 19 5 14 Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. Bore size × ■Single foot type PBDA PBDA -1A Stroke Bore size A+Stroke C+Stroke 28 20 15 J N 6 ●φ6 Head cover M5×0.8 4 M5×0.8 Note 1 (M3×0.5) φ9 φU1 6 AP AD AG LB L □B φV LY AT AH K Width across flats I □8 AC+Stroke AB AP AY AE M5×0.8 (M3×0.5)Note 1 G 8 AA+Stroke AF ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M-1A PBDA ●Lateral piping (-A) Bore size × Stroke -A-1A PBDA A+3+Stroke A+3+Stroke M5×0.8 (M3×0.5) Note1 9 M5×0.8 φU2 9 4.5 4.5 8 4 φU2 L □B1 □B1 Code A B C B1 G I J K L N U1 U2 V AA AB AC AD AE AF AG AH 6 [0.236] 77 12 49 12 14.5 5.5 2.4 M3×0.5 M6×1 10 − 14 3 61 21 56 5 32 22.2 7 9 10 [0.394] 71 12 43 12 13 7 3.2 M4×0.7 M8×1 8.5 11 14 4 55 21 50 5 32 22.2 7 9 16 [0.630] 71.5 17 43.5 17 11.5 8 4 M5×0.8 M10×1 7 17 19 5 58.5 19 52.5 6 42 29.2 9 14 Bore mm [in.] Code AP AT AY LB LY 6 [0.236] 4.2 1.6 10 15 16 10 [0.394] 4.2 1.6 12 15 16 16 [0.630] 5.2 2.3 14 22.5 24 Bore mm [in.] Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. Dimensions of Double Acting Type (mm) ■ Double foot type PBDA Bore size × PBDA -M-1 Stroke Bore size A+Stroke C+Stroke 28 20 15 J G 8 M5×0.8 M5×0.8 L 8 4.5 N L AP □B K Width across flats I LB φV AY AE AH AT LY 4 Width across flats B1 AD AG 9 AC+Stroke AP AB AF Code A C B B1 G I J 10 [0.394] 82 54 12 12 13 7 3.2 M4×0.7 17 17 11.5 8 4 Bore mm [in.] 16 [0.630] 82.5 54.5 K L N V AB AC AD AE AF AG AH AP AT AY LB LY M8×1 8.5 4 21 60 5 32 22.2 7 9 4.2 1.6 12 15 16 7 5 19 64.5 6 42 29.2 9 14 5.2 2.3 14 22.5 24 M5×0.8 M10×1 動フランジ形 Bore size × ■Flange type PBDA PBDA -3 Stroke Bore size A+Stroke C+Stroke M5×0.8 (M3×0.5)Note 1 28 20 15 J N ●φ6 Head cover M5×0.8 M5×0.8 Note 1 (M3×0.5) φ9 6 φU1 4 □B φV AY L K BF 6 BC BP G 8 □8 Width across flats I BB BE BT ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M-3 PBDA ●Lateral piping (-A) Bore size × Stroke -A-3 PBDA A+3+Stroke A+3+Stroke M5×0.8 (M3×0.5) Note1 M5×0.8 φU2 9 9 4.5 4.5 8 4 φU2 L □B1 □B1 Code A C B B1 G I J K L N U1 U2 V AY BB BC BE BF BP BT 6 [0.236] 77 49 12 12 14.5 5.5 2.4 M3×0.5 M6×1 10 − 14 3 10 26.4 14 32 22.2 4.2 1.6 10 [0.394] 71 43 12 12 13 7 3.2 M4×0.7 M8×1 8.5 11 14 4 12 26.4 14 32 22.2 4.2 1.6 16 [0.630] 71.5 43.5 17 17 11.5 8 4 M5×0.8 M10×1 7 17 19 5 14 25.7 20 42 29.2 5.2 2.3 Bore mm [in.] Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. Dimensions of Double Acting Type (mm) Bore size × ●Clevis mounting type PBDA Stroke PBDA -7 Bore size A+Stroke CA+Stroke 28 R CB+Stroke 15 G 8 M5×0.8 4.5 φP S φU φV φU M5×0.8 N J K □B Q L Width across flats I □B G1 Code A B G G1 I J K L N P Q R S U V CA CB 10 [0.394] 87 12 13 22 7 3.2 M4×0.7 M8×1 8.5 3.2 +0.09 +0.06 3.2+0.2 +0.1 13 8 14 4 82 67 16 [0.630] 92.5 17 11.5 27 8 4 M5×0.8 M10×1 7 5 +0.09 +0.06 6.5+0.1 +0.2 18 10 19 5 84.5 69.5 Bore mm [in.] 7 Bore size × ●Basic type PBSA Stroke PBSA Bore size A C 28 20 15 J ●φ6 Head cover M5×0.8 6 M5×0.8 Note 1 (M3×0.5) φ9 6 4 φV φU1 φU G 8 □8 L K □B Width across flats AY Width across flats I ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M PBSA ●Lateral piping (-A) Bore size × Stroke -A PBSA A+3 A+3 M5×0.8 (M3×0.5) Note1 φU2 9 Code Stroke 9 4.5 M5×0.8 4.5 Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. 8 φU2 L □B1 □B1 C A 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 6 [0.236] 72 77 82 92 97 102 122 127 132 137 142 147 44 49 54 64 69 74 94 99 104 109 114 119 10 [0.394] 71 76 81 91 96 101 116 121 126 131 136 141 43 48 53 63 68 73 88 93 98 103 108 113 16 [0.630] 76.5 81.5 86.5 96.5 101.5 106.5 121.5 126.5 131.5 136.5 141.5 146.5 48.5 53.5 58.5 68.5 73.5 78.5 93.5 98.5 103.5 108.5 113.5 118.5 Bore mm [in.] Code B B1 G I J K L U U1 U2 V AY 6 [0.236] 8 8 4.5 5.5 2.4 M3×0.5 M6×1 9 − 10.8 3 10 10 [0.394] 12 12 3 7 3.2 M4×0.7 M8×1 14 11 14 4 12 16 [0.630] 17 17 6.5 8 4 M5×0.8 M10×1 19 17 19 5 14 Bore mm [in.] Bore size × ●Single foot type PBSA -1A Stroke PBSA Bore size A C 28 20 G 8 15 J 6 φU1 φV □8 LB AP Width across flats I AD AG AC AP AB AA ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M-1A PBSA ●Lateral piping (-A) Bore size × Stroke -A-1A PBSA AF A+3 A+3 M5×0.8 (M3×0.5) Note1 φU2 9 M5×0.8 4.5 Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. Bore mm [in.] Code Stroke 6 [0.236] 10 [0.394] 16 [0.630] Bore mm [in.] M5×0.8 Note 1 (M3×0.5) φ9 6 4 L K AY AE ●φ6 Head cover M5×0.8 LY AT AH ト形 Dimensions of Single Acting Push Type (mm) 9 4.5 8 L □B1 A φU2 C □B1 AA 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 72 77 82 92 97 102 122 127 132 137 142 147 44 49 54 64 69 74 94 99 104 109 114 119 56 61 66 76 81 86 106 111 116 121 126 131 71 76 81 91 96 101 116 121 126 131 136 141 43 48 53 63 68 73 88 93 98 103 108 113 55 60 65 75 80 85 100 105 110 115 120 125 76.5 81.5 86.5 96.5 101.5 106.5 121.5 126.5 131.5 136.5 141.5 146.5 48.5 53.5 58.5 68.5 73.5 78.5 93.5 98.5 103.5 108.5 113.5 118.5 63.5 68.5 73.5 83.5 88.5 93.5 108.5 113.5 118.5 123.5 128.5 133.5 Code Stroke AC 5 10 15 20 25 30 35 40 45 50 55 60 B1 G I J K L U1 U2 V AB AD AE AF AG AH AP AT AY LB LY 6 [0.236] 51 56 61 71 76 81 101 106 111 116 121 126 8 4.5 5.5 2.4 M3×0.5 M6×1 − 10.8 3 21 5 32 22.2 7 9 4.2 1.6 10 13 16 10 [0.394] 50 55 60 70 75 80 12 3 3.2 M4×0.7 M8×1 11 14 4 21 5 32 22.2 7 9 4.2 1.6 12 15 16 16 [0.630] 57.5 62.5 67.5 77.5 82.5 87.5 102.5 107.5 112.5 117.5 122.5 127.5 17 6.5 8 4 M10×1 17 19 5 19 6 42 29.2 9 14 5.2 2.3 14 22.5 24 95 100 105 110 115 120 7 M5×0.8 Dimensions of Single Acting Push Type (mm) ■ Double foot type PBSA Bore size × -M-1 Stroke PBSA Bore size A C 28 20 M5×0.8 G 8 9 8 4.5 15 J K AY AE L LB φV AT AT AH AH LY LY 4 AP Widths across flats I Widths across flats B1 AD AG AP AP AB AA AF Bore mm [in.] Code Stroke A C AA 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 59 64 74 79 84 99 104 109 114 119 124 60 65 70 90 105 110 115 120 125 130 82 16 [0.630] 87.5 92.5 97.5 107.5 112.5 117.5 132.5 137.5 142.5 147.5 152.5 157.5 59.5 64.5 69.5 79.5 84.5 89.5 104.5 109.5 114.5 119.5 124.5 129.5 69.5 74.5 79.5 89.5 94.5 99.5 114.5 119.5 124.5 129.5 134.5 139.5 Code 87 92 102 107 112 127 132 137 142 147 152 54 10 [0.394] 80 85 B1 G I J K L V AB AD AE AF AG AH AP AT AY LB LY 10 [0.394] 12 3 7 3.2 M4×0.7 M8×1 4 21 5 32 22.2 7 9 4.2 1.6 12 15 16 16 [0.630] 17 6.5 8 4 M5×0.8 M10×1 5 19 6 42 29.2 9 14 5.2 2.3 14 22.5 24 Bore mm [in.] Bore size × ■Flange type PBSA PBSA -3 Stroke Bore size A C 28 20 8 6 ●φ6 Head cover M5×0.8 M5×0.8 Note 1 (M3×0.5) φ9 6 φU1 4 φV BC BP 15 J G AY □8 L K BF Width across flats I BB BE BT ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M-3 PBSA ●Lateral piping (-A) Bore size × Stroke -A-3 PBSA A+3 A+3 M5×0.8 (M3×0.5) Note1 φU2 9 M5×0.8 4.5 9 4.5 8 L □B1 Code Stroke φU2 □B1 C A 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 6 [0.236] 72 77 82 92 97 102 122 127 132 137 142 147 44 49 54 64 69 74 94 99 104 109 114 119 10 [0.394] 71 76 81 91 96 101 116 121 126 131 136 141 43 48 53 63 68 73 88 93 98 103 108 113 16 [0.630] 76.5 81.5 86.5 96.5 101.5 106.5 121.5 126.5 131.5 136.5 141.5 146.5 48.5 53.5 58.5 68.5 73.5 78.5 93.5 98.5 103.5 108.5 113.5 118.5 Bore mm [in.] Bore mm [in.] Code B1 G I J K L U1 U2 V AY BB BC BE BF BP BT 6 [0.236] 8 4.5 5.5 2.4 M3×0.5 M6×1 − 10.8 3 10 26.4 14 32 22.2 4.2 1.6 10 [0.394] 12 3 7 3.2 M4×0.7 M8×1 11 14 4 12 26.4 14 32 22.2 4.2 1.6 16 [0.630] 17 6.5 8 4 M5×0.8 M10×1 17 19 5 14 25.7 20 42 29.2 5.2 2.3 Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. Dimensions of Single Acting Push Type (mm) Bore size × ●Clevis mounting type PBSA -7 Stroke PBSA Bore size 7 A CA CB 23 R 8 15 G φU M5×0.8 4.5 S φP J φV φU K □B Bore mm [in.] Code Stroke L Q □B G1 Width across flats I A CA CB 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 B G G1 I J 10 [0.394] 12 3 22 7 3.2 M4×0.7 K 16 [0.630] 17 6.5 27 8 4 87 59 64 74 79 84 99 104 109 114 119 124 92.5 97.5 102.5 112.5 117.5 122.5 137.5 142.5 147.5 152.5 157.5 162.5 84.5 89.5 94.5 104.5 109.5 114.5 129.5 134.5 139.5 144.5 149.5 154.5 61.5 66.5 71.5 81.5 86.5 91.5 106.5 111.5 116.5 121.5 126.5 131.5 Bore mm [in.] 82 97 102 107 122 127 132 137 142 147 54 82 16 [0.630] Code 87 92 102 107 112 127 132 137 142 147 152 77 10 [0.394] L P Q R S U V M8×1 3.2 +0.09 +0.06 3.2 +0.2 +0.1 13 18 14 4 +0.09 +0.06 6.5 +0.2 +0.1 18 10 19 5 M5×0.8 M10×1 5 Dimensions of Single Acting Pull Type (mm) Bore size × ●Basic type PBTA Stroke PBTA Bore size A 28+Stroke C 20+Stroke 15 φU M5×0.8 (M3×0.5)Note G 8 N J ●φ6 Head cover 6 6 4 φV φU1 φ9 K □B Code Stroke □8 L Width across flats AY Width across flats I C A 5 10 15 20 25 30 5 10 15 20 25 30 6 [0.236] 87 97 107 122 132 142 54 59 64 74 79 84 10 [0.394] 86 96 106 121 131 141 53 58 63 73 78 83 16 [0.630] 86.5 96.5 106.5 121.5 131.5 141.5 53.5 58.5 63.5 73.5 78.5 83.5 Bore mm [in.] Code B G I J K L N U U1 V AY 6 [0.236] 12 14.5 5.5 2.4 M3×0.5 M6×1 10 14 − 3 10 10 [0.394] 12 13 7 3.2 M4×0.7 M8×1 8.5 14 11 4 12 16 [0.630] 17 11.5 8 4 M5×0.8 M10×1 7 19 17 5 14 Bore mm [in.] Note: For bore sizeφ6 only. Bore size × ●Single foot type PBTA -1A Stroke PBTA Bore size A C 28+Stroke 20+Stroke G 8 15 N J M5×0.8 (M3×0.5)Note ●φ6 Head cover 6 6 4 K AY AE L Width across flats I AP AD AG LB φV AT AH LY φU1 φ9 AC AB+Stroke AP □8 Width across flats B AA AF Code Stroke C A AA AC 5 10 15 20 25 30 5 10 15 20 25 30 5 10 15 20 25 30 5 10 15 20 25 30 6 [0.236] 87 97 107 122 132 142 54 59 64 74 79 84 66 71 76 86 91 96 61 66 71 81 86 91 10 [0.394] 86 96 106 121 131 141 53 58 63 73 78 83 65 70 75 85 90 95 60 65 70 80 85 90 16 [0.630] 86.5 96.5 106.5 121.5 131.5 141.5 53.5 58.5 63.5 73.5 78.5 83.5 68.5 73.5 78.5 88.5 93.5 98.5 62.5 67.5 72.5 82.5 87.5 92.5 Bore mm [in.] Code B G I J K L N U1 V AB AD AE AF AG AH AP AT AY LB LY 6 [0.236] 12 14.5 5.5 2.4 M3×0.5 M6×1 10 − 3 21 5 32 22.2 7 9 4.2 1.6 10 15 16 10 [0.394] 12 13 7 3.2 M4×0.7 M8×1 8.5 11 4 21 5 32 22.2 7 9 4.2 1.6 12 15 16 16 [0.630] 17 11.5 8 4 M5×0.8 M10×1 7 17 5 19 6 42 29.2 9 14 5.2 2.3 14 22.5 24 Bore mm [in.] Note: For bore sizeφ6 only. Dimensions of Single Acting Pull Type (mm) Bore size × ●Flange type PBTA -3 Stroke PBTA Bore size A 28+Stroke C 20+Stroke 15 N J ●φ6 Head cover 6 6 4 φU1 φ9 φV BC BP M5×0.8 (M3×0.5)Note G 8 AY K BF L □8 Width across flats B Width across flats I BB+Stroke BE Code Stroke AT C A Bore mm [in.] 5 10 15 20 25 30 5 10 15 20 25 30 6 [0.236] 87 97 107 122 132 142 54 59 64 74 79 84 10 [0.394] 86 96 106 121 131 141 53 58 63 73 78 83 16 [0.630] 86.5 96.5 106.5 121.5 131.5 141.5 53.5 58.5 63.5 73.5 78.5 83.5 Code B G I J K L N U1 V AT AY BB BC BE BF BP 6 [0.236] 12 14.5 5.5 2.4 M3×0.5 M6×1 10 − 3 1.6 10 26.4 14 32 22.2 4.2 10 [0.394] 12 13 7 3.2 M4×0.7 M8×1 8.5 11 4 1.6 12 26.4 14 32 22.2 4.2 16 [0.630] 17 11.5 8 4 M5×0.8 M10×1 7 17 5 2.3 14 25.7 20 42 29.2 5.2 Bore mm [in.] Note: For bore sizeφ6 only. Bore size × ●Clevis mounting type PBTA -7 Stroke PBTA Bore size 7 A CA 28+Stroke CB 20+Stroke 8 15 G M5×0.8 φP S N J φU φV φU K □B Q L Code Stroke □B G1 Width across flats I CA A CB 5 10 15 20 25 30 5 10 15 20 25 30 5 10 15 20 25 30 10 [0.394] 102 112 122 137 147 157 97 107 117 132 142 152 64 69 74 84 89 94 16 [0.630] 107.5 117.5 127.5 142.5 152.5 162.5 99.5 109.5 119.5 134.5 144.5 154.5 66.5 71.5 76.5 86.5 91.5 96.5 Bore mm [in.] Code B G G1 I J K L N P Q S U V 10 [0.394] 12 13 22 7 3.2 M4×0.7 M8×1 8.5 3.2 +0.09 +0.06 3.2 +0.2 +0.1 8 14 4 16 [0.630] 17 11.5 27 8 4 M5×0.8 M10×1 7 5 +0.09 +0.06 6.5 +0.1 +0.2 10 19 5 Bore mm [in.] PEN CYLINDERS φ2.5, φ4 Single Acting Push Type Symbol ●Single acting push type Bore Size and Stroke Specifications mm [in.] Bore size mm [in.] Item Operation type 2.5 [0.098] 4 [0.157] Single acting push type Media Air Mounting type Basic type Operating pressure range MPa [psi.] Proof pressure 0.34〜0.7 [49〜102] 1.05 [152] MPa [psi.] Operating temperature range 0〜60 [32〜140] 50〜300 [2.0〜11.8] °C [°F] Operating speed range mm/s [in./sec.] applications with high load ratio or high speed, use ( Inexternally ) mounted stoppers. Cushion None Lubrication Not required Minimum operating pressure MPa [psi.] Port size Operation type Standard strokes Note Bore size Single acting push type Maximum available stroke 2.5 5, 10 10 4 5, 10, 15, 20 20 Stroke tolerance +1.2 +0.047 –0.2 [ –0.008 ] Note: Because collars are used for non-standard strokes, use the figures for the length one size up from the non-standard stroke. Single Acting Type Spring Return Force N [lbf.] Spring return force 0.34 [49] Bore size mm [in.] φ4×φ2.5 2.5 [0.098] 0.6 [0.13] 0.6 [0.13] 4 [0.157] 1.5 [0.34] 1.5 [0.34] 1.5 [0.34] 1.5 [0.34] Barb fitting for nylon and urethane tubes is equipped with the head cover. 10St 5St 15St 20St − − End of stroke 1.2 [0.27] 2.8 [0.63] Remark: Cylinders with bore sizeφ2.5 are sold in packs of 5. Order Code Mass g [oz.] PB SA Bore size × Stroke Stroke mm Bore size mm [in.] 5 10 15 2.5 [0.098] 1.5 [0.053] 1.9 [0.067] − − 4 [0.157] 3.4 [0.120] 4.4 [0.155] 5.2 [0.183] 6.1 [0.215] 20 Remark: Includes a mounting nut and rod end nut (φ4 only). Single acting push type Dimensions of Single Acting Push Type (mm) Pen cylinder series Inner Construction (cannot be disassembled) φ4×φ2.5 C 1.5 3.5 5 φ3.2 4 w t φ3.5 φ1 ●Single acting push type φ2.5, φ4 Applicable tube 1.6 M2.5×0.45 r q Stroke ●Basic typeφ2.5 PBSA2.5 × A ●Basic typeφ4 PBSA4 × Stroke M4×0.7 u e y M2×0.4 1.6 4 6 5 7 3 Applicable tube φ4×φ2.5 φ5 i No. Parts Materials q q Rod cover Brass (nickel plated) w w Head cover Brass (nickel plated) e e Piston rod Stainless steel r r Spring holder Stainless steel t t Spring Steel y y Piston seal Synthetic rubber (NBR) u u Mounting nut Brass (nickel plated) i i Rod end nut Note Brass (nickel plated) Note: For bore size φ4 only. Not available for bore size φ2.5. φ3.2 Major Parts and Materials C 6 5 A Bore mm [in.] A Code C 20 5 10 15 20 5 10 15 2.5 [0.098] 26.5 35.5 − − 16.5 25.5 − − 4 [0.157] 37 46 55 64 19 28 37 46 Note: Because collars are used for non-standard strokes, use the figures for the length one size up from the non-standard stroke. PEN CYLINDERS Non-rotating Cylinders Symbols ● Non-rotating double acting type ● Non-rotating single acting push type ● Non-rotating single acting pull type Specifications Bore Size and Stroke ●Double acting type Item Operation type Bore size mm [in.] Mounting type 10 [0.394] 16 [0.630] Double acting type, Single acting push type, Single acting pull type Bore size Basic type, Foot type, Flange type, Clevis type 10 5, 10, 15, 30, 45, 60 100 Air 16 5, 10, 15, 30, 45, 60 150 Media Operating pressure range MPa [psi.] Proof pressure Standard strokes Note +1.5 +0 +0.059 [ +0 ] 0.1〜0.7 [15〜102] Note1 MPa [psi.] Operating temperature range mm [in.] Maximum Stroke available tolerance stroke ●Single acting type 1.05 [152] °C [°F] 0〜70 [32〜158] Operating speed range mm/s [in./sec.] 50〜500 [2.0〜19.7] Note2 Cushion Fixed type (rubber bumper) Lubrication Not required Port size M5×0.8 ±2° Non-rotating accuracy Operation type Bore size Single acting push type 10 Single acting pull type 10 16 16 mm [in.] Maximum available stroke Stroke tolerance 5, 10, 15, 30, 45, 60 60 [ +0.059 ] +0 5, 10, 15, 30 30 Standard strokes Note +1.5 +0 +1.5 +0 +0.059 [ +0 ] Notes: 1. Single acting push type: 0.15 〜 0.7 [22 〜 102] Single acting pull type: 0.2 〜 0.7 [29 〜 102] 2. Single acting push type and single acting pull type: 50 〜 300 [2.0 〜 11.8] Note: For non-standard strokes: Collars are added to standard stroke cylinders of the next size up. Mounting Type Single Acting Type Spring Return Force N [lbf.] Remark Mounting type Name 1A, 1 Single foot type, double foot type Included at shipping Bore size mm 3 Flange type Included at shipping 10 5.1 [1.15] 4.4 [0.99] 3.7 [0.83] 3.7 [0.83] 4.2 [0.94] 3.7 [0.83] 5.9 [1.33] 7 Clevis type (with pin) Assembled and shipped 16 8.5 [1.91] 7.3 [1.64] 6.1 [1.37] 6.1 [1.37] 7.0 [1.57] 6.1 [1.37] 9.8 [2.20] Clevis type with supporting bracket (with pin) Supporting bracket included at shipping 7-7C Spring return force 5St 10St 15St 30St 45St 60St End of stroke Order Codes PB − 10×30 − − − Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet Rod end accessory Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Operation type DAL Non-rotating double acting type SAL Non-rotating single acting push type TAL Non-rotating single acting pull type Pen cylinder series Head cover piping specification Blank Axial direction piping A Lateral piping※ M Lateral piping with mounting thread※ ※ -A, -M correspond only to double acting type and single acting push type. Not available for clevis mounting type. ( ) Mounting type (Included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only on head cover -M specification) 1A Single foot mounting type 3 Flange mounting type 7 Clevis mounting type (With pin, and non-rotating double acting type only) 7-7C Clevis mounting type with pin and clevis supporting bracket (Non-rotating double acting type only) Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Lead wire length A 1000mm [39in.] B 3000mm [118in.] Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mass g [oz.] Operation type Mounting type Basic type Double acting type Single acting push type Single acting pull type Stroke mm Bore size mm Clevis mounting type Basic type Basic type Additional mass 5 10 15 30 Cylinder Sensor switch Lateral piping Note 2 -A -M Clevis Note 1 with magnet (1 pc.) Mounting type 60 45 Single foot Flange 1 [0.04] 10 25 [0.88] 26 [0.92] 27 [0.95] 30 [1.06] 34 [1.20] 37 [1.31] 18 [0.63] 12 [0.42] 16 45 [1.59] 47 [1.66] 49 [1.73] 55 [1.94] 60 [2.12] 65 [2.29] 18 [0.63] 12 [0.42] 10 29 [1.02] 30 [1.06] 31 [1.09] 34 [1.20] 38 [1.34] 41 [1.45] − − 2 [0.07] A:20 [0.71] 3 [0.11] 8 [0.28] − 32 [1.13] 1 [0.04] B:50 [1.76] − 16 56 [1.98] 58 [2.05] 60 [2.12] 66 [2.33] 71 [2.50] 76 [2.68] − − 45 [1.59] 2 [0.07] 10 23 [0.81] 24 [0.85] 25 [0.88] 30 [1.06] 38 [1.34] 41 [1.45] 18 [0.63] 12 [0.42] − 1 [0.04] 16 45 [1.59] 47 [1.66] 49 [1.73] 58 [2.05] 73 [2.57] 78 [2.75] 18 [0.63] 12 [0.42] − 2 [0.07] 10 25 [0.88] 27 [0.95] 28 [0.99] 33 [1.16] − − 18 [0.63] 12 [0.42] − 1 [0.04] 16 48 [1.69] 50 [1.76] 51 [1.80] 61 [2.15] − − 18 [0.63] 12 [0.42] − 2 [0.07] − 2 [0.07] 6 [0.21] − − − A:20 [0.71] 2 [0.07] 6 [0.21] B:50 [1.76] 3 [0.11] 8 [0.28] A:20 [0.71] B:50 [1.76] − − − − Remark: Includes mounting nut and rod end nut. For the mass of the double foot bracket, add double the mass of the single foot bracket listed above. Notes: 1. With supporting bracket and pin. 2. Same for all sensor switch models (ZC253□, ZC230□, ZC201□, ZC205□). Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 r !0 q i Parts No. e ●Clevis mounting type (-7) ot y u w Materials q q Rod cover Aluminum alloy (nickel plated) w w Head cover Aluminum alloy (nickel plated) e e Cylinder tube r r Piston rod Stainless steel t t Piston Aluminum alloy ●Lateral piping (-A) y y Magnet Note Plastic magnet w u u Piston seal i i Rod seal o o Bumper w Synthetic rubber (NBR) !0 !0 Mounting nut Mild steel (nickel plated) Rod end nut !1 !1 Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. ●Lateral piping with mounting thread (-M) w !0 No. ●Single acting push type o r !0 q !1 e ●Lateral piping (-A) !2 i yt u w ●Lateral piping with mounting thread (-M) w !0 w Materials Parts q q Rod cover Aluminum alloy (nickel plated) w w Head cover Aluminum alloy (nickel plated) e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Bumper o o Rod end nut !0 !0 Mounting nut !1 !1 Spring Steel !2 !2 Collar Aluminum alloy Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. No. ●Single acting pull type !1 r !0 q i ou y t !3 !2 e w Parts Materials q q Rod cover Aluminum alloy (nickel plated) w w Head cover Aluminum alloy (nickel plated) e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note1 Plastic magnet u u Piston seal i i Rod seal o o Bumper Note2 !0 !0 Mounting nut !1 !1 Rod end nut !2 !2 Spring Steel !3 !3 Collar Aluminum alloy Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. Dimensions of Non-rotating Double Acting Type (mm) Bore size × ●Basic type PBDAL Stroke Cross section of the rod A+Stroke C+Stroke 28 φ10:4.2 φ16:5.2 20 15 J 6 M5×0.8 N 4 φU1 φU M5×0.8 G 8 K L Width across flats I Width across flats AY □B ●Lateral piping with mounting thread (-M) Bore size × Stroke -M PBDAL ●Lateral piping (-A) Bore size × Stroke -A PBDAL A+3+Stroke A+3+Stroke M5×0.8 9 4.5 M5×0.8 φU2 9 4.5 8 4 φU2 L □B1 Code □B1 A B B1 C I J K L N G AY U U1 U2 10 [0.394] 71.5 14 12 43 7 3.2 M4×0.7 M10×1 8.5 13 14 17 11 14 16 [0.630] 71.5 17 17 43.5 8 4 M5×0.8 M12×1 7 11.5 17 19 17 19 Bore mm [in.] Bore size × ●Clevis mounting type PBDAL -7 Stroke Cross section of the rod A+Stroke CA+Stroke CB+Stroke 15 φ10:4.2 φ16:5.2 R 5 G 8 M5×0.8 N J 4.5 S T Q φU M5×0.8 K □B L Width across flats I G1 φP1 (Hole diameter) φP2 (Pin diameter) Code A B G G1 I J K L N P1 P2 Q R S T U CA CB 10 [0.394] 87 14 13 22 7 3.2 M4×0.7 M10×1 8.5 3.2 +0.09 +0.06 3.2 +0.03 0 3.2 +0.2 +0.1 13 8 15.5 17 82 67 16 [0.630] 92.5 17 11.5 27 8 4 M5×0.8 M12×1 7 5 +0.03 0 6.5 +0.1 +0.2 18 10 21 19 84.5 69.5 Bore mm [in.] +0.09 +0.06 5 Dimensions of Non-rotating Single Acting Push Type (mm) Bore size × ●Basic type PBSAL Stroke Cross section of the rod A C 28 20 φ10:4.2 φ16:5.2 15 J 6 M5×0.8 4 φU1 φU G 8 K □B L Width across flats I Width across flats AY ●Lateral piping with mounting thread (-M) Bore size × Stroke -M PBSAL ●Lateral piping (-A) Bore size × Stroke -A PBSAL A+3 A+3 M5×0.8 M5×0.8 φU2 9 9 8 4 4.5 4.5 φU2 L □B1 Code Stroke □B1 C A 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 10 [0.394] 71 76 81 91 96 101 116 121 126 131 136 141 43 48 53 63 68 73 88 93 98 103 108 113 16 [0.630] 76.5 81.5 86.5 96.5 101.5 106.5 121.5 126.5 131.5 136.5 141.5 146.5 48.5 53.5 58.5 68.5 73.5 78.5 93.5 98.5 103.5 108.5 113.5 118.5 Bore mm [in.] Code B B1 G I J K L U U1 U2 AY 10 [0.394] 14 12 3 7 3.2 M4×0.7 M10×1 17 11 14 14 16 [0.630] 17 17 6.5 8 4 M5×0.8 M12×1 19 17 19 17 Bore mm [in.] Dimensions of Non-rotating Single Acting Pull Type (mm) Bore size × ●Basic type PBTAL Stroke Cross section of the rod A 28+Stroke φ10:4.2 φ16:5.2 C 20+Stroke 15 6 N J 4 φU1 φU M5×0.8 G 8 K □B Code Stroke L Width across flats I Width across flats AY C A 5 10 15 20 25 30 5 10 15 20 25 30 10 [0.394] 86 96 106 121 131 141 53 58 63 73 78 83 16 [0.630] 86.5 96.5 106.5 121.5 131.5 141.5 53.5 58.5 63.5 73.5 78.5 83.5 Bore mm [in.] Code B G I J K L N U U1 AY 10 [0.394] 14 13 7 3.2 M4×0.7 M10×1 8.5 17 11 14 16 [0.630] 17 11.5 8 4 M5×0.8 M12×1 7 19 17 17 Bore mm [in.] Handling Instructions and Precautions (Non-rotating Cylinders) 1. To mount the cylinder body in place, first secure the rod cover, and then tighten the mounting nuts to the recommended torque shown below. Bore size mm [in.] Recommended tightening torque N・cm [in・lbf] 10 [0.394] 600 [53] 16 [0.630] 1200 [106] 2. For non-rotating cylinders, avoid applying rotation torque to the piston rod. The bushing section will become deformed and non-rotating accuracy will deteriorate. 3. For single acting cylinders, avoid applying loads while returning by spring force. Spring inside the cylinder could not make return the carrying work to the end of stroke. PEN CYLINDERS Double Rod Cylinders Symbol Specifications Bore Size and Stroke mm Bore size mm [in.] 10 [0.394] 16 [0.630] Maximum available stroke Operation type Double acting type Bore size Mounting type Basic type, Foot type, Flange type 10 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 60 Air 16 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 75, 100 100 Item Media 0.1〜0.7 [15〜102] Operating pressure range MPa [psi.] Proof pressure 1.05 [152] MPa [psi.] Operating temperature range °C [°F] 0〜70 [32〜158] Operating speed range mm/s [in./sec.] 50〜750 [2.0〜29.5] Cushion Fixed type (Rubber bumper) Lubrication Not required Port size M5×0.8 Standard strokes Note Note: For non-standard strokes: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, collar packed to the next size up stroke of cylinder. Mounting Type Mounting type Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Included at shipping Flange type Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAD 10×30 − − − Bore size × Stroke Lead wire length A 1000mm [39in.] B 3000mm [118in.] Cylinder specification Blank Standard cylinder S Cylinder with magnet DAD Double acting double rod type Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Rod end accessory (Included at shipping) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Pen cylinder series Mounting type Blank Basic type 1 Double foot mounting type 1A Single foot mounting typeNote 3 Flange mounting type Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Major Parts and Materials Inner Construction (cannot be disassembled) ●Double acting type !0 e o q u w it r y No. Parts Materials q q Rod cover Aluminum alloy (nickel plated) w w Cylinder tube e e Piston rod r r Piston Aluminum alloy t t Magnet Note Plastic magnet y y Piston seal u u Rod seal i i Bumper Stainless steel Synthetic rubber (NBR) o o Mounting nut Mild steel (nickel plated) Rod end nut !0 !0 Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. Mass g [oz.] Additional mass Stroke mm Bore mm [in.] Mounting bracket Cylinder Sensor switch with magnet ZC253□ ZC230□ ZC201□ ZC205□ 60 75 100 -1A 51 46 10 32.7 34.4 37.7 39.4 50 42.7 44.4 47.7 36 41 [0.394] [1.153] [1.213] [1.270] [1.330] [1.390] [1.446] [1.506] [1.566] [1.623] [1.683] [1.764] [1.799] − − 7 [0.25] 5 14 [0.49] [0.18] 1 [0.04] 87.5 92.5 80 60 16 67.5 62.5 85 18 90 77.5 75 82.5 65 70 72.5 [0.630] [2.116] [2.205] [2.293] [2.381] [2.469] [2.557] [2.646] [2.734] [2.822] [2.910] [2.998] [3.086] [3.175] [3.263] [0.63] 12 36 [1.27] [0.42] 2 [0.07] 5 10 15 20 25 30 35 Remark: Includes mounting nut and rod end nut. 40 45 50 55 -1 -3 A:20 [0.71] B:50 [1.76] Dimensions of Double Rod Type (mm) Bore size × ●Basic type PBDAD PBDAD Stroke Bore size A+(Stroke×2) 20 M5×0.8 G 8 15 J M5×0.8 8 G N N J 4 4 φV φU 28+Stroke C+Stroke 28 L K □B Width across flats I Code Width across flats AY A C B G I J K L N U V AY 10 [0.394] 116 60 12 13 7 3.2 M4×0.7 M8×1 8.5 14 4 12 16 [0.630] 115 59 17 11.5 8 4 M5×0.8 M10×1 7 19 5 14 PBDAD Bore size Bore mm [in.] Bore size × ●Single foot type PBDAD -1A Stroke A+(Stroke×2) 28+Stroke C+Stroke 28 20 15 J M5×0.8 G 8 M5×0.8 8 G N N 4 J 2-K AY AE 2-L Width across flats I Width across flats B AP AB AP AD AG LB φV AT AH LY 4 AF Code A C B G I J K L N V AB AD AE AF AG AH AP AT AY LB LY 10 [0.394] 116 60 12 13 7 3.2 M4×0.7 M8×1 8.5 4 21 5 32 22.2 7 9 4.2 1.6 12 15 16 16 [0.630] 115 59 17 11.5 8 4 M5×0.8 M10×1 7 5 19 6 42 29.2 9 14 5.2 2.3 14 22.5 24 Bore mm [in.] Dimensions of Double Rod Type (mm) ● Double foot type PBDAD Bore size × PBDAD -1 Stroke Bore size A+(Stroke×2) 28+Stroke C+Stroke 28 20 15 J M5×0.8 G 8 M5×0.8 8 G N N 4 J 2-K AY AE 2-L Width across flats I AP AD AG AP AG Width across flats B AA+Stroke AD AP AB LB φV AT AH LY 4 AF Code N V AA AB AD AE AF AG AH AP AT AY LB LY 8.5 4 74 21 5 32 22.2 7 9 4.2 1.6 12 15 16 5 77 19 6 42 29.2 9 14 5.2 2.3 14 22.5 24 L K A C B G I J 10 [0.394] 116 60 12 13 7 3.2 M4×0.7 M8×1 16 [0.630] 115 59 17 11.5 8 4 M5×0.8 M10×1 7 Bore mm [in.] Bore size × ●Flange type PBDAD Stroke PBDAD -3 Bore size A+(Stroke×2) 20 G 8 15 J M5×0.8 M5×0.8 8 G N N 4 J 4 φV BC BP 28+Stroke C+Stroke 28 AY 2-K BF 2-L Width across flats B Width across flats I BB BE Code BT A C B G I J K L N V AY BB BC BE BF BP BT 10 [0.394] 116 60 12 13 7 3.2 M4×0.7 M8×1 8.5 4 12 26.4 14 32 22.2 4.2 1.6 16 [0.630] 115 59 17 11.5 8 4 M5×0.8 M10×1 7 5 14 25.7 20 42 29.2 5.2 2.3 Bore mm [in.] PEN CYLINDERS Pull Side Stroke Adjusting Cylinders Symbol Specifications Bore Size and Stroke mm [in.] Bore size mm [in.] Item 10 [0.394] 16 [0.630] Operation type Double acting type Mounting type Basic type, Foot type, Flange type Bore size 10 Air Media Operating pressure range MPa [psi.] Proof pressure 0.08〜0.7 [12〜102] 0.06〜0.7 [9〜102] 1.05 [152] MPa [psi.] 0〜70 [32〜158] Operating temperature range °C [°F] 50〜750 [2.0〜29.5] Operating speed range mm/s [in./sec.] Cushion Fixed type (Rubber bumper on rod side Note) Lubrication Not required Port size M5×0.8 Stroke adjusting range mm [in.] 16 Standard strokes Note 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 75, 100, 125, 150 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 Maximum Stroke available tolerance stroke 150 200 +1.5 +0 [ +0.059 ] +0 +1.5 +0 +0.059 [ +0 ] 75, 100, 125, 150, 175, 200 Note: The non-standard stroke: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, collar packed to the next size up stroke of cylinder. Mounting Type 0〜−15 [0〜−0.591] Note: No cushion on head side. Mounting type Name Remark 1A Single foot type Note Included at shipping 3 Flange type Included at shipping Note: When the stroke exceeds 60mm, do not use the single foot type. Order Codes PB DAE 10×30 − A − − − Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet DAE Double acting single rod type, pull side stroke adjusting cylinder Pen cylinder series Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Lead wire length A 1000mm [39in.] B 3000mm [118in.] Rod end accessory (Included at shipping) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Mounting type (Included at shipping) Blank Basic type 1A Single foot mounting type Note 3 Flange mounting type Note: When the stroke exceeds 60mm, do not use the single foot mounting type. Head cover piping specification A Lateral piping Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 r No. !0 q i e w !3 !4 ot y u !2 Materials Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut Mild steel (nickel plated) !1 !1 Rod end nut Mild steel (nickel plated) !2 !2 Stroke adjusting bolt Steel (nickel plated) !3 !3 Seal washer Mild steel+synthetic rubber (NBR) Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Lock nut Mild steel (nickel plated) !4 !4 Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. Mass g [oz.] Additional mass Stroke mm Bore mm [in.] 20 15 30 25 35 40 45 50 Mounting bracket Cylinder 55 60 75 100 125 150 175 200 -1A -3 Sensor switch with magnet ZC253□ ZC230□ ZC201□ ZC205□ 10 [0.394] 32 33.2 34.4 35.5 36.7 37.9 39 40.2 41.4 42.5 43.7 44.9 46 47.2 − [1.129] [1.171] [1.213] [1.252] [1.295] [1.337] [1.376] [1.418] [1.460] [1.499] [1.541] [1.584] [1.623] [1.665] − 7 [0.25] 5 [0.18] 1 [0.04] 16 [0.630] 52 53.9 55.7 57.5 59.4 61.2 63 64.9 66.7 68.5 70.4 72.2 74 75.9 77.7 79.5 [1.834] [1.901] [1.965] [2.028] [2.095] [2.159] [2.222] [2.289] [2.353] [2.416] [2.483] [2.547] [2.610] [2.677] [2.741] [2.804] 18 [0.63] 12 [0.42] 2 [0.07] A:20 [0.71] B:50 [1.76] Remark: Includes mounting nut and rod end nut. Dimensions of Pull Side Stroke Adjusting Type (mm) Bore size × ●Basic type PBDAE Stroke Bore size 20MAX. A+Stroke C+Stroke 28 20 M5×0.8 G 8 15 J M5×0.8 N 12 5.3 8 7.5 4 φV φU PBDAE Code Width across flats I M5×0.8 L K □B Width across flats AY A C B G I J K L N U V AY 10 [0.394] 77 49 12 13 7 3.2 M4×0.7 M8×1 8.5 14 4 12 16 [0.630] 77.5 49.5 17 11.5 8 4 M5×0.8 M10×1 7 19 5 14 Bore mm [in.] 281 PEN CYLINDERS Push Side Stroke Adjusting Cylinders PEN CYLINDERS Symbol Bore Size and Stroke Specifications mm [in.] Bore size mm [in.] Item 10 [0.394] 16 [0.630] Operation type Double acting type Mounting type Basic type, Foot type, Flange type Air Media 1.05 [152] MPa [psi.] Operating temperature range °C [°F] 0〜70 [32〜158] Operating speed range mm/s [in./sec.] 50〜750 [2.0〜29.5] Cushion Rubber bumper Lubrication Not required Port size M5×0.8 Stroke adjusting range Maximum Stroke available tolerance stroke Standard strokes Note 10 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 60 16 15, 20, 25, 30, 35, 40, 45, 50, 55, 60, 75, 100 100 0.1〜0.7 [15〜102] Operating pressure range MPa [psi.] Proof pressure Bore size +1.5 +0 [ +0.059 ] +0 +1.5 +0 [ +0.059 ] +0 Note: The non-standard stroke: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, consult us. Mounting Type 0〜−15 [0〜−0.591] mm [in.] Mounting type Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAP 10×30 − M − − − Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet DAP Double acting single rod type, push side stroke adjusting cylinder Pen cylinder series Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Lead wire length A 1000mm [39in.] B 3000mm [118in.] Rod end accessory (Included at shipping) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Mounting type (Included at shipping) Blank Nose type 1 Double foot mounting type 1A Single foot mounting typeNote 3 Flange mounting type Note: When the stroke exceeds 60mm, use the double foot mounting type for the foot bracket. Head cover piping specification M Lateral piping with mounting thread Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 ot yu e r !0 q i Parts No. !2 w !4 !3 !5 Materials q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut !1 !1 Rod end nut !2 !2 Stroke adjusting rod Stainless steel !3 !3 Stroke adjusting knob Aluminum alloy (nickel plated) !4 !4 Bumper Synthetic rubber (NBR) !5 !5 Rock nut Mild steel (nickel plated) Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. Mass CS03−10NDJ−A00 g [oz.] Additional mass Stroke mm Bore mm [in.] 15 25 20 30 35 40 45 Mounting bracket 50 55 -1A -3 Cylinder with magnet 60 75 100 10 [0.394] 39 40.7 42.4 44 45.7 47.4 49 50.7 52.4 54 [1.376] [1.436] [1.496] [1.552] [1.612] [1.672] [1.728] [1.788] [1.848] [1.905] − − 5 7 14 [0.49] [0.25] [0.18] 1 [0.04] 16 [0.630] 12 18 72 74.5 77 79.5 82 84.5 87 89.5 92 94.5 97 99.5 36 [2.540] [2.628] [2.716] [2.804] [2.892] [2.981] [3.069] [3.157] [3.245] [3.333] [3.422] [3.510] [1.27] [0.63] [0.42] 2 [0.07] -1 Sensor switch ZC253□ ZC230□ ZC201□ ZC205□ A:20 [0.71] B:50 [1.76] Remark: Includes mounting nut and rod end nut. Dimensions of Push Side Stroke Adjusting Type (mm) Bore size × ●Basic type PBDAP PBDAP Stroke Bore size A+(2×Stroke) 15 J M5×0.8 M5×0.8 G 8 N 22 8 G J 2 N 4 4 φV φDE 20 φU DF+Stroke C+Stroke 28 L K □B Code Width across flats AY Width across flats AY Width across flats I K Width across flats I (Width across flats) φ10:6 φ16:8 A C B G I J K L N U V AY DE DF 10 [0.394] 123.5 60 12 13 7 3.2 M4×0.7 M8×1 8.5 14 4 12 8 35.5 16 [0.630] 122.5 59 17 11.5 8 4 M5×0.8 M10×1 7 19 5 14 10 35.5 Bore mm [in.] PEN CYLINDERS Heat Resistant Specification Cylinders Symbol Bore Size and Stroke Specifications mm [in.] Bore size mm [in.] Item 6 [0.236] 10 [0.394] 16 [0.630] Operation type Double acting type Mounting type See the table at lower right. Media Air Operating pressure range MPa [psi.] Proof pressure 0.3〜0.7 [44〜102] MPa [psi.] 0.2〜0.7 [29〜102] 0.15〜0.7 [22〜102] 6 0〜150 [32〜302] Operating speed range mm/s [in./sec.] 50〜500 [2.0〜19.7] None Fixed type (Rubber bumper) Lubrication Not required Port size M5×0.8 Remark: Fluoro rubber is used for seals. Contact us for details on the specifications. Standard strokes Note 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 10 1.05 [152] Operating temperature range °C [°F] Cushion Bore size Maximum Stroke available tolerance stroke 16 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 75, 100, 125, 150 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 75, 100, 125, 150, 175, 200 100 150 +1.5 +0 [ +0.059 ] +0 200 Note: The non-standard stroke: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, collar packed to the next size up stroke of cylinder. Mounting Type Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping 7 Clevis type (with pin) Assembled at the factory for shipping Clevis type with supporting bracket (with pin) Supporting bracket included at shipping Mounting type 7-7C Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAF 10×30 − − Caution Sensor switches cannot be used with the heat resistant specification cylinders. − Bore size × Stroke Rod end accessory (Included at shipping,φ 10 and φ 16 only) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) DAF Double acting single rod type, heat resistant specification Pen cylinder series Mounting type (Brackets included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only on head cover -M specification) 1A Single foot mounting type Note 3 Flange mounting type 7 Clevis mounting type (with pin) (For φ10 and φ16 only) 7-7C Clevis mounting type with supporting bracket (with pin) (For φ10 and φ16 only) Note: When the stroke exceeds 60mm, use the double foot mounting type for the foot bracket. Head cover piping specification (Not available in clevis mounting type) Blank Axial direction piping A Lateral piping M Lateral piping with mounting thread (For φ10 and φ16 only) Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type i r !0 q u e ot y w ●Clevis mounting type (-7) w Materials No. Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston y y Piston seal u u Rod seal i i Rod end nut Mild steel (nickel plated) o o Bumper Fluoro rubber !0 !0 Mounting nut Mild steel (nickel plated) Aluminum alloy (nickel plated) Stainless steel Aluminum alloy Fluoro rubber ●Lateral piping (-A) w ●Lateral piping with mounting thread (-M) w !0 Mass ●The mass is the same as the standard double acting type (standard cylinders). See p.260. Dimensions ●The dimensions are the same as the standard double acting type. See p.262〜264. CS03−10ND−A00 CS03−10ND−A00 CS03−10ND−A00 PEN CYLINDERS Low Hydraulic Cylinders Symbol Specifications Bore Size and Stroke mm [in.] Bore size mm [in.] Item 6 [0.236] 10 [0.394] 16 [0.630] Double acting type Operation type Mounting type See the table at lower right. Media Note1, Note2 Turbine oil with defoaming agent (ISO VG22〜100 or equivalent) Operating pressure range MPa [psi.] Proof pressure 0.3〜0.7 [44〜102] 0.2〜0.7 [29〜102] 5〜300 [0.2〜11.8] mm/s [in./sec.] None Cushion 10 16 0〜60 [32〜140] Operating temperature rangeNote3 °C [°F] Fixed type (Rubber bumper) M5×0.8 Port size Notes: 1. The low hydraulic cylinder is recommended to be used with oil on both sides. The use of oil on one side and air on the other side could result in imprecise speed control, and oil could leak across to the air side. In addition, use meter-out control for the speed control. 2. Do not use nonflammable hydraulic fluid, machine oil, or spindle oil. 3. Be aware that changes in oil temperature can alter the speed. 4. When using the reed switch type sensor, maintain a minimum speed of 30mm/s [1.2in./sec.] or more. Standard strokes Note 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 75, 100, 125, 150 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 75, 100, 125, 150, 175, 200 150 +1.5 +0 +0.059 [ +0 ] 200 Mounting Type Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping 7 Clevis type (with pin) Assembled and shipped Clevis type with supporting bracket (with pin) Supporting bracket included at shipping Mounting type Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes 10×30 − − − − Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet DAH 100 Note: The non-standard stroke: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, collar packed to the next size up stroke of cylinder. 7-7C PB DAH Maximum Stroke available tolerance stroke 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 6 1.05 [152] MPa [psi.] Operating speed rangeNote4 0.15〜0.7 [22〜102] Bore size Double acting single rod type, low hydraulic cylinder Pen cylinder series Rod end accessory Blank No knuckle I With I type knuckle Y With Y type knuckle (with pin) ● For bore sizes of φ10 and φ16 only. ● As for the cylinder joints and the cylinder rod ends, order separately. Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Lead wire length A 1000mm [39in.] B 3000mm [118in.] Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mounting type (Brackets included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only on head cover -M specification) 1A Single foot mounting type Note 3 Flange mounting type 7 Clevis mounting type (with pin) (For φ10 and φ16 only) 7-7C Clevis mounting type with supporting bracket (with pin) (For φ10 and φ16 only) Note: When the stroke exceeds 60mm, use the double foot mounting type for the foot bracket. Head cover piping specification (Not available for clevis mounting type) Blank Axial direction piping A Lateral piping M Lateral piping with mounting thread (For φ10 and φ16 only) Inner Construction (cannot be disassembled) !1 r !0 q i e Major Parts and Materials o yt u w ●Clevis mounting type (-7) w Materials No. Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut Mild steel (nickel plated) !1 !1 Rod end nut Mild steel (nickel plated) Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. ●Lateral piping (-A) w ●Lateral piping with mounting thread (-M) w !0 CS03−10ND−A00 CS03−10ND−A00 CS03−10ND−A00 Mass ●The mass is the same as the standard double acting type (Standard cylinders). See p.260. Dimensions ●The dimensions are the same as the standard double acting type. See p.262〜264. CS03−10ND−A00 PEN CYLINDERS Dual Stroke Cylinders Symbol Specifications Bore Size and Stroke mm [in.] Bore size mm [in.] Item 10 [0.394] 16 [0.630] Operation type Double acting type Mounting type See the table at lower right. Air Media Operating pressure range MPa [psi.] 0.08〜0.7 [12〜102] Proof pressure 0.06〜0.7 [9〜102] 1.05 [152] MPa [psi.] Operating temperature range °C [°F] 0〜70 [32〜158] Operating speed range mm/s [in./sec.] 50〜750 [2.0〜29.5] Standard strokes Note Bore size 10 16 Stroke 1 Stroke 2 5, 10, 15, 20, 25, 30 5, 10, 15, 20, 25, 30 35, 40, 45, 50, 55, 60 35, 40, 45, 50, 55, 60 5, 10, 15, 20, 25, 30 5, 10, 15, 20, 25, 30 35, 40, 45, 50, 55, 60 35, 40, 45, 50, 55, 60 Note: For non-standard strokes, contact us. Cushion Fixed type (Rubber bumper) Lubrication Not required Port size M5×0.8 Maximum available Stroke stroke St1+St2 tolerance 120 120 +1.5 +0 [ +0.059 ] +0 Mounting Type Mounting type Remark Name 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping Note: When the total stroke (St1+St2) exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAW 10×30×30 − − − Bore size × Stroke 1 × Stroke 2 Cylinder specification Blank Standard cylinder S Cylinder with magnet DAW Double acting single rod type, dual stroke cylinder Pen cylinder series Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Lead wire length A 1000mm [39in.] B 3000mm [118in.] Rod end accessory Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● For bore sizes of φ10 and φ16 only. ● As for the cylinder joints and the cylinder rod ends, order separately. Mounting type (Included at shipping) Blank Basic type 1 Double foot mounting type 1A Single foot mounting typeNote 3 Flange mounting type Note: When the total stroke (St1+St2) exceeds 60mm, use the double foot mounting type for the foot bracket. Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Inner Construction (cannot be disassembled) !1 r !0 q i e w o ty u Major Parts and Materials No. Operation of Dual Stroke Cylinders Dual Stroke Cylinders are a set of 2 cylinders connected back to back. The cylinder body can be secured in place and each stroke can be controlled separately. It can also be used to obtain 2-stage or 3-stage strokes by securing the piston rod on one side in place. Materials Parts q q Rod cover w w Connecting cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut !1 !1 Rod end nut Aluminum alloy (nickel plated) D Stainless steel Cylinder 2 Synthetic rubber (NBR) A CB The rods retract stroke 1 and stroke 2 when air is supplied from Ports A and D. Cylinder 1 D B C A The rod moves stroke 1 when air is supplied from Ports B and D. MIld steel (nickel plated) Stroke 1 Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. D C D C A B The rod moves stroke 2 when air is supplied from Ports A and C. Stroke 2 B A Stroke 2 The rod moves stroke 1 and stroke 2 when air is supplied from Ports B and C. Stroke 1 Mass g [oz.] Additional mass Bore size mm [in.] Zero stroke mass Each 15mm [0.591in.] strokes of St. 1 and St. 2 -1 -1A -3 Cylinder with magnet ‐A ‐M ZC253□ ZC230□ ZC201□ ZC205□ 7 [0.25] A:20 [0.71] B:50 [1.76] Mounting bracket Sensor switch Lateral piping 10 [0.394] 50 [1.76] 3.5 [0.123] 14 [0.49] 5 [0.18] 2 [0.07] 2 [0.07] 6 [0.21] 16 [0.630] 89 [3.14] 5.5 [0.194] 36 [1.27] 18 [0.63] 12 [0.42] 4 [0.14] 3 [0.11] 8 [0.28] Remark: Includes mounting nut and rod end nut. Calculation example: The mass for 2 units of ZC253A, with a double acting cylinder with magnet with single foot bracket, bore size of 10mm, and stroke 1 of 15mm and stroke 2 of 15mm, is 50+2+7+3.5+3.5+20×2 =106g [3.74oz.] Dimensions of Dual Stroke Cylinder (mm) ●Basic type PBDAW PBDAW Bore size × Stroke1 × Stroke2 Bore size A+Stroke1+Stroke2 20 G 8 15 4.5 N J M5×0.8 M5×0.8 28 M5×0.8 G 4.5 8 20 15 4 J N 4 φV 2-L 2-K □B Width across flats AY Width across flats I Code φU φV φU M5×0.8 C+Stroke2 19 C+Stroke1 28 Width across flats AY □B Width across flats I A C B G I J K L N U V AY 10 [0.394] 149 37 12 13 7 3.2 M4×0.7 M8×1 8.5 14 4 12 16 [0.630] 150 37.5 17 11.5 8 4 M5×0.8 M10×1 7 19 5 14 Bore mm [in.] PEN CYLINDERS Tandem Cylinders Symbol Specifications Bore Size and Stroke mm [in.] Bore size mm [in.] Item 10 [0.394] Stroke1 (standard)Note 16 [0.630] Operation type Double acting type Mounting type See the table at lower right. Operating pressure range MPa [psi.] Proof pressure 0.15〜0.7 [22〜102] Operating speed range mm/s [in./sec.] Maximum available Stroke stroke (St1×2)+St2 tolerance 10 0, 5, 10, 15, 20, 25, 30 150 16 0, 5, 10, 15, 20, 25, 30 150 +1.5 +0 +0.059 [ +0 ] Remark: Figures in the table are a combination of stroke 1 (standard) and its corresponding stroke 2 (standard). Note: For non-standard strokes, consult us. 1.05 [152] MPa [psi.] 0〜70 [32〜158] Operating temperature range °C [°F] 35, 40, 45, 50, 55, 60 Bore size Air Media 5, 10, 15, 20, 25, 30, 50〜750 [2.0〜29.5] Cushion Fixed type (Rubber bumper) Lubrication Not required Port size M5×0.8 Mounting Type Mounting type Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping 7 Clevis type (with pin) Assembled and shipped 7-7C Clevis type with supporting bracket (with pin) Supporting bracket included at shipping Note: When the total stroke (St1×2 + St2) exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAT 10×30×30 − − − − Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Bore size × Stroke 1 × Stroke 2 Cylinder specification Blank Standard cylinder S Cylinder with magnet DAT Double acting single rod type, tandem cylinder Pen cylinder series Lead wire length A 1000mm [39in.] B 3000mm [118in.] Rod end accessory (Included at shipping) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mounting type (Brackets included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only on head cover -M specification) 1A Single foot mounting type Note 3 Flange mounting type ●About Stroke 1 and Stroke 2 7 Clevis mounting type (with pin) 7-7C Clevis mounting type with supporting bracket (with pin) Cylinder2 Cylinder1 Note: When the total stroke (St1×2+St2) exceeds 60mm, use the double foot mounting type for the foot bracket. Head cover piping specification (Not available for clevis mounting type) Blank Axial direction piping A Lateral piping M Lateral piping with mounting thread Stroke 2 Stroke 1 Stroke 1 is the stroke for cylinder 1. Stroke 2 is obtained by subtracting Stroke 1 from the stroke of cylinder 2. Inner Construction (cannot be disassembled) !1 r !0 q i e ot y u Major Parts and Materials w !2 w ●Clevis mounting type (-7) w ●Lateral piping (-A) w !0 ●Lateral piping with mounting thread (-M) Materials q q Parts Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut !1 !1 Rod end nut !2 !2 Connecting cover Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Aluminum alloy (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. Mass Operation of Tandem Cylinders CS03−10ND−A00 g [oz.] Bore size mm [in.] No. Additional mass Zero stroke mass Each 15 strokes Mounting bracket Cylinder Lateral piping with Basic type Clevis type of st.1 and st.2 -1ANote -3 magnet -A -M 10 [0.394] 34 [1.20] 38 [1.34] 3.5 [0.123] 16 [0.630] 64 [2.26] 76 [2.68] 5.5 [0.194] Tandem Cylinders are a setCS03−10ND−A00 of 2 cylinders joined end to end. It can be used as a 2-stage stroke cylinder by supplying air to either Port A or Port B. It can also obtain twice the thrust within the “stroke 1” range. CS03−10ND−A00 Sensor switch C A B The rods retract strokes 2 and 1 when air is supplied from Port C. 7 [0.25] 5 [0.18] 2 [0.07] 2 [0.07] 6 [0.21] A:20 [0.71] 18 [0.63] 12 [0.42] 4 [0.14] 3 [0.11] 8 [0.28] B:50 [1.76] Note: For the double foot (-1), add double the mass of the single foot bracket. Remark: Includes mounting nut and rod end nut. Calculation example: The mass for 2 units of ZC253A, with a double acting cylinder with magnet with single foot bracket, bore size of 10mm, and stroke 1 of 15mm and stroke 2 of 15mm, is 34+2+7+3.5+3.5+20 × 2 = 90g [3.17oz.]. Cylinder2 Cylinder1 C B C B C B A The rod moves stroke 1 when air is supplied from Port A. A The rod moves stroke 2 when air is supplied from Port B. Stroke2 Stroke1 Example of Air Circuit for Tandem Cylinders See the following air circuit when using the tandem cylinder as a 2-stage stroke cylinder. ●For upward-operation cylinder Cylinder 2 Cylinder 1 St2 St1 St2 St1 Cylinder SOL2 SOL1 SOL1 SOL2 Cylinder 2 Cylinder 1 ●For downward- or horizontal-operation cylinder St2 SOL1 (0.3MPa)※ SOL2 St1 SOL3 Cylinder HR 0.5MPa St1 St2 High relief regulator ※Set pressure as required. SOL1 SOL2 SOL3 A Twice the thrust is obtained within the stroke 1 range when air is supplied from Ports A and B. Dimensions of Tandem Cylinder (mm) ●Basic type PBDAT PBDAT Bore size × Stroke1 × Stroke2 Bore size A+(2×Stroke 1)+Stroke 2 20 G 8 15 φU Point E C+Stroke 1+Stroke 2 28 M5×0.8 6 M5×0.8 4.5 N J D+Stroke 1 G1 M5×0.8 φV φU1 4 L K □B Width across flats AY Width across flats I ● Lateral piping Bore size × Stroke1 × Stroke2 -A PBDAT ● Lateral piping with mounting thread Bore size × Stroke1 × Stroke2 -M PBDAT Point E Point E D+3+Stroke 1 D+3+Stroke 1 M5×0.8 M5×0.8 φU 9 9 4.5 4.5 8 4 φU L □B Code □B A C B D G G1 I J K L N U U1 V AY 10 [0.394] 108 37 12 30 13 13 7 3.2 M4×0.7 M8×1 8.5 14 11 4 12 16 [0.630] 111.5 37.5 17 32 11.5 14 8 4 M5×0.8 M10×1 7 19 17 5 14 Bore mm [in.] ● Clevis mounting type PBDAT PBDAT Bore size × Stroke1 × Stroke2 -7 7 Bore size A+(2×Stroke 1)+Stroke 2 E+(2×Stroke 1)+Stroke 2 C+Stroke 1+Stroke 2 28 20 G 8 15 M5×0.8 D1+Stroke 1 G1 R M5×0.8 M5×0.8 4.5 N 4.5 S φP J φU φV φU Q L K □B Width across flats I Code □B G2 A C B D1 E G G1 G2 I J K L N P Q R S U V 10 [0.394] 124 37 12 41 119 13 13 22 7 3.2 M4×0.7 M8×1 8.5 3.2+0.09 +0.06 3.2 +0.2 +0.1 13 8 14 4 16 [0.394] 132.5 37.5 17 45 124.5 11.5 14 27 8 4 M5×0.8 M10×1 7 5 +0.09 +0.06 6.5 +0.2 +0.1 18 10 19 5 Bore mm [in.] PEN CYLINDERS Cylinders for Clean Systems Symbols ●Double acting type ●Single acting push type Specifications Bore size mm [in.] Item Bore Size and Stroke ●Double acting type 6 [0.236] 10 [0.394] 16 [0.630] Bore size Double acting type, Single acting push type Operation type mm [in.] Maximum available stroke Standard strokes Note Air Media Mounting type Double acting Operating pressure type range MPa [psi.] Single acting push type Proof pressure Basic type, Foot type, Flange type, Clevis type (clevis type of φ10 and φ16 only) 6 0.15〜0.7 [22〜102] 0.1〜0.7 [15〜102] 10 0.3〜0.7 [44〜102] 0.15〜0.7 [22〜102] MPa [psi.] 1.05 [152] Operating temperature range °C [°F] 50〜300 [2.0〜11.8] Lubrication Not required Port size 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 M5×0.8 +1.5 +0 150 75, 100, 125, 150 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 [ +0.059 ] +0 200 75, 100, 125, 150, 175, 200 Operation type Bore size Single acting push type 10 Rubber bumper None 100 ●Single acting type 0〜60 [32〜140] Operating speed range mm/s [in./sec.] Cushion 16 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 55, 60 Stroke tolerance Note Note: M3 × 0.5 can also be selected at φ6 only. 6 16 mm [in.] Standard strokes Note Maximum available stroke Stroke tolerance 75 5, 10, 15, 20, 25, 30, 105 35, 40, 45, 50, 55, 60 120 +1.5 +0 [ +0.059 ] +0 Note: The non-standard stroke: For strokes divisible by 5, cylinder tube cutting is used. For strokes not divisible by 5, collar packed to the next size up stroke of cylinder. Order Codes CS − PB 10×30 − − − − Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet Operation type DA Double acting type SA Single acting push type Cylinders for clean systems ( Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mounting type (Included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only onφ10 and φ16 of head cover -M specification double acting type and -M specification single acting push type) 1A Single foot mounting type 3 Flange mounting type 7 Clevis mounting type (with pin for bore sizes of φ10 andφ16 only) 7-7C Clevis mounting type with pin and clevis supporting bracket (For bore sizes of φ10 and φ16 only) Pen cylinder series Head cover piping specification Blank Axial direction piping A Lateral piping (not available for clevis mounting type) M Lateral piping with mounting thread ※ ※ -M available only in φ10 and φ16 of double acting type and single acting push type. Not available for clevis mounting type. Lead wire length A 1000mm [39in.] B 3000mm [118in.] ) Connection port Blank M5×0.8 (φ6, φ10, φ16) M3 M3×0.5 (φ6 only) Order Codes for Mounting Brackets Only Name Bore size mm 6 Mounting type 10 Remark Name Mounting type 16 1 Double foot type Included at shipping Single foot bracket CS-1A-PBDA6 CS-1A-PBDA10 CS-1A-PBDA16 1A Single foot type Note Included at shipping Double foot bracket CS-1-PBDA6 CS-1-PBDA10 CS-1-PBDA16 3 Flange type Included at shipping Flange bracket CS-3-PBDA6 CS-3-PBDA10 CS-3-PBDA16 7 Clevis type (with pin) Assembled and shipped Clevis supporting bracket − Clevis type with supporting bracket (with pin) Supporting bracket included at shipping CS-7C-PBDA10 CS-7C-PBDA16 7-7C Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Mass Single acting push type Double acting type Operation type g [oz.] Mounting Bore type mm Basic type Additional mass Stroke mm 5 10 15 20 25 30 35 40 45 50 Mounting type 55 60 75 100 125 150 175 200 Single foot Flange Clevis Cylinder with magnet Sensor switch (1 pc.)Note 2 6 18.8 19.4 20 20.8 21.4 22 22.4 22.8 23 23.6 24.2 25 − [0.663] [0.684] [0.705] [0.734] [0.755] [0.776] [0.790] [0.804] [0.811] [0.832] [0.854] [0.882] − − 7 5 [0.25] [0.18] − 0.5 [0.018] − 10 30 31 29 32 33.3 34.6 36 37 38 28 39 42.4 48.1 53.8 59.5 27 − [0.952] [0.988] [1.023] [1.058] [1.093] [1.129] [1.175] [1.220] [1.270] [1.305] [1.340] [1.376] [1.496] [1.697] [1.898] [2.099] − 7 5 [0.25] [0.18] − 1 [0.04] 2 [0.07] 16 12 47.8 49.4 51 52.6 54.2 56 57.6 59.2 61 62.3 63.6 66 71.3 80.1 88.9 97.7 106.5 115.3 18 [1.686] [1.743] [1.799] [1.855] [1.912] [1.975] [2.032] [2.088] [2.152] [2.198] [2.243] [2.328] [2.515] [2.825] [3.136] [3.446] [3.757] [4.067] [0.63] [0.42] − 2 [0.07] 3 [0.11] − − − 30.8 31.9 33 33.8 34.9 36 37.8 38.9 40 40.8 41.9 43 46.3 51.8 57.3 62.8 − − 10 Clevis [1.086] [1.125] [1.164] [1.192] [1.231] [1.270] [1.333] [1.372] [1.411] [1.439] [1.478] [1.517] [1.633] [1.827] [2.021] [2.215] mounting type 59.4 61.2 63 64.4 66.2 68 69.4 71.2 73 74.4 76.2 78 83.4 92.4 101.4 110.4 119.4 128.4 (with pin) 16 [2.095] [2.159] [2.222] [2.272] [2.335] [2.399] [2.448] [2.511] [2.575] [2.624] [2.688] [2.751] [2.942] [3.259] [3.577] [3.894] [4.212] [4.529] Basic type Note 1 Additional mass of Lateral piping − − 1 32 [1.13] [0.04] − − 2 45 [1.59] [0.07] − A:20 [0.71] B:50 [1.76] − 6 15.8 16.4 17 19.8 20.4 21 22.8 23.4 24 24.8 25.4 26 − [0.557] [0.578] [0.600] [0.698] [0.720] [0.741] [0.804] [0.825] [0.847] [0.875] [0.896] [0.917] − − − − − 7 5 [0.25] [0.18] − 0.5 [0.018] 10 26.8 27.9 29 31.8 32.9 34 39.8 40.9 42 42.8 43.9 45 − [0.945] [0.984] [1.023] [1.122] [1.160] [1.199] [1.404] [1.443] [1.481] [1.510] [1.549] [1.587] − − − − − 18 12 [0.63] [0.42] − 1 [0.04] 2 [0.07] 16 50.4 52.2 54 58.4 60.2 62 72.4 74.2 76 77.4 79.2 81 − [1.778] [1.841] [1.905] [2.060] [2.123] [2.187] [2.554] [2.617] [2.681] [2.730] [2.794] [2.857] − − − − − 18 12 [0.63] [0.42] − 2 [0.07] 3 [0.11] − − − − − − − 1 32 [1.13] [0.04] − − − − − − − − 2 45 [1.59] [0.07] − 29.8 30.9 32 34.8 35.9 37 42.8 43.9 45 45.8 46.9 48 10 − Clevis [1.051] [1.090] [1.129] [1.228] [1.266] [1.305] [1.510] [1.549] [1.587] [1.616] [1.654] [1.693] mounting type 92 90.2 88.4 87 83.4 83.4 73 71.2 61.4 63.2 65 69.4 (with pin) 16 − [2.166] [2.229] [2.293] [2.448] [2.511] [2.575] [2.942] [2.942] [3.069] [3.118] [3.182] [3.245] Remark : Includes mounting nut and rod end nut. The clevis mounting type does not include mounting nut. For the mass of the double foot bracket, add double the mass of the single foot bracket listed above. Notes: 1. With supporting bracket and pin. 2. Same for all sensor switch models (ZC253□, ZC230□, ZC201□, ZC205□). Calculation example: The mass for 2 units of ZC253A, with a double acting cylinder with magnet with single foot bracket, bore size of 10mm, and stroke of 45mm, is 36+7+1+40=84g [2.96oz.]. − Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 r i !0 q No. e i oty u w Parts Materials q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut !1 !1 Rod end nut Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. ●Single acting push type o r !3 !0 q e !1 No. !2 ity u w Parts Materials q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Note1 Plastic magnet u u Piston seal i i Bumper o o Rod end nut !0 !0 Mounting nut !1 !1 Spring Steel !2 !2 Collar !3 !3 Rod seal Aluminum alloy Synthetic rubber (NBR) CS03−10ND−A00 Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. Dimensions of Double Acting Cylinder for Clean Systems (mm) Bore size × ■Basic type CS - PBDA Stroke A+Stroke C+Stroke 28 20 G 8 6 Note1 M5×0.8(M3×0.5) (Dust collection port) N1 N2 4 15 φU M5×0.8 (M3×0.5)Note1 M5×0.8 ●φ6 Head cover J M5×0.8 Note1 (M3×0.5) φ9 φV □B φU1 6 L K Width across flats I □8 Width across flats AY ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M CS - PBDA ●Lateral piping (-A) Bore size × Stroke -A CS - PBDA A+3+Stroke A+3+Stroke M5×0.8 (M3×0.5)Note1 9 M5×0.8 φU2 9 8 4 4.5 4.5 L □B1 Code Bore mm [in.] φU2 □B1 A C B B1 G I J K L N1 N2 U U1 U2 V AY 6 [0.236] 87 59 12 8 24.5 5.5 2.4 M3×0.5 M8×1 10 10 14 − 10.8 3 12 10 [0.394] 81 53 12 12 23 7 3.2 M4×0.7 M10×1 6.5 12 14 11 14 4 14 16 [0.630] 81.5 53.5 17 17 21.5 8 4 M5×0.8 M12×1 5 12 19 17 19 5 17 Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. Bore size × ■Clevis mounting type CS - PBDA Stroke -7 A+Stroke CA+Stroke CB+Stroke 15 8 20 R G M5×0.8 M5×0.8 (Dust collection port) N1 N2 M5×0.8 J 4.5 φP S φU φV φU K □B Q L □B G1 Width across flats I Code A B G G1 I J N1 N2 P Q R S U V CA CB 10 [0.394] 97 12 23 22 7 3.2 M4×0.7 M10×1 6.5 12 3.2 +0.09 +0.06 3.2+0.2 +0.1 13 8 14 4 92 69 17 21.5 27 8 4 M5×0.8 M12×1 5 12 5 +0.09 +0.06 6.5+0.1 +0.2 18 10 19 5 94.5 69.5 Bore mm [in.] 16 [0.630] 102.5 K L Dimensions of Single Acting Push Type Cylinder for Clean Systems (mm) Bore size × ●Basic type CS - PBSA Stroke A C 28 20 G 8 6 M5×0.8(M3×0.5) Note1 J ●φ6 Head cover 4 M5×0.8 Note1 (M3×0.5) φ9 6 φV □B φU1 φU M5×0.8 (Dust collection port) N 15 L K Width across flats I □8 Width across flats AY ●Lateral piping with mounting thread (-M) Note 2 Bore size × Stroke -M CS - PBSA ●Lateral piping (-A) Bore size × Stroke -A CS - PBSA A+3 A+3 M5×0.8 (M3×0.5)Note1 M5×0.8 φU2 9 4.5 Notes: 1. For bore size φ6 only. 2. Not available for bore size φ6. 8 φU2 L □B1 Code □B1 C A Stroke 9 4.5 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 6 [0.236] 87 92 97 107 112 117 137 142 147 152 157 162 59 64 69 79 84 89 109 114 119 124 129 134 10 [0.394] 86 91 96 106 111 116 131 136 141 146 151 156 58 63 68 78 83 88 103 108 113 118 123 128 16 [0.630] 86.5 91.5 96.5 106.5 111.5 116.5 131.5 136.5 141.5 146.5 151.5 156.5 58.5 63.5 68.5 78.5 83.5 88.5 103.5 108.5 113.5 118.5 123.5 128.5 Bore mm [in.] Code B B1 G I J K L N U U1 U2 V AY 6 [0.236] 12 8 14.5 5.5 2.4 M3×0.5 M8×1 8 14 − 10.8 3 12 10 [0.394] 12 12 13 7 3.2 M4×0.7 M10×1 8.5 14 11 14.0 4 14 16 [0.630] 17 17 11.5 8 4 M5×0.8 M12×1 7 19 17 19.0 5 17 Bore size × Stroke Bore mm [in.] ●Clevis mounting type CS - PBSA -7 A CA 23 CB G 8 15 N R M5×0.8 (Dust collection port) M5×0.8 4.5 J S φP φU φV φU K □B Stroke □B G1 Code Bore mm [in.] Q L Width across flats I A CA CB 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 5 10 15 20 25 30 35 40 45 50 55 60 197.5 102.5 107.5 117 122 127 142 147 152 157 162 167 92 16 [0.630] 102.5 107.5 112.5 122.5 127.5 132.5 147.5 152.5 157.5 162.5 167.5 172.5 94.5 99.5 104.5 114.5 119.5 124.5 139.5 144.5 149.5 154.5 159.5 164.5 71.5 76.5 81.5 91.5 96.5 101.5 116.5 121.5 126.5 131.5 136.5 141.5 Bore mm [in.] Code 97 102 112 117 122 137 142 147 152 157 162 69 99 114 119 124 129 134 139 10 [0.394] 74 B G G1 I J N P Q R S U V 10 [0.394] 12 13 22 7 3.2 M4×0.7 M10×1 8.5 3.2 +0.09 +0.06 3.2 +0.2 +0.1 13 8 14 4 16 [0.630] 17 11.5 27 8 4 7 5 +0.09 +0.06 6.5 +0.2 +0.1 18 10 19 5 K L M5×0.8 M12×1 79 89 94 MADE TO ORDER PEN CYLINDERS Cylinders with Variable Cushions Symbol ●For delivery, consult us. Specifications Bore Size and Stroke mm [in.] Bore size mm [in.] Item 10 [0.394] 16 [0.630] Operation type Double acting type Mounting type See the table at lower right. Air Media Operating pressure range MPa [psi.] Proof pressure 0.2〜0.7 [29〜102] Standard strokes Note 10 25, 50, 75, 100 16 0.1〜0.7 [15〜102] 150 300 25, 50, 75, 100 +1.5 +0 [ +0.059 ] +0 Note: For non-standard strokes, consult us. 1.05 [152] MPa [psi.] Operating temperature range °C [°F] 0〜70 [32〜158] Operating speed range mm/s [in./sec.] 100〜1000 [3.9〜39.4] Mounting Type Variable cushion type Cushion mm [in.] 8 [0.315] Allowable kinetic energy J [in·lbf] 0.07 [0.62] Cushion stroke Bore size Maximum Stroke available stroke tolerance Mounting type 10 [0.394] 0.18 [1.59] Lubrication Not required Port size M5×0.8 Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping 7 Clevis type (with pin) Assembled and shipped 7-7C Clevis type with supporting Supporting bracket bracket (with pin) included at shipping Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAC S 10×25 − M − − − Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Bore size × Stroke S DAC Lead wire length A 1000mm [39in.] B 3000mm [118in.] Cylinder with magnet (magnet is standard equipment) Double acting single rod type, with variable cushion Pen cylinder series Rod end accessory (Included at shipping) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mounting type (Brackets included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only on head cover -M specification) 1A Single foot mounting type Note 3 Flange mounting type 7 Clevis mounting type (with pin) 7-7C Clevis mounting type with supporting bracket (with pin) Note: When the stroke exceeds 60mm, use the double foot mounting type for the foot bracket. Head cover piping specification (Not available for clevis mounting type) M Lateral piping with mounting thread Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 r !0 qi !2 e o t yu ●Clevis mounting type (-7) !3 w w !3 Materials No. Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy y y Magnet Plastic magnet u u Piston seal i i Rod seal o o Cushion seal !0 !0 Mounting nut !1 !1 Rod end nut !2 !2 Tube gasket Synthetic rubber (NBR) !3 !3 Needle Stainless steel Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Mass g [oz.] Bore size mm [in.] Stroke mm Mounting type 25 10 [0.394] 16 [0.630] Basic type Additional mass 50 75 -1A -1 -3 36 [1.27] 42 [1.48] 48 [1.69] 53 [1.87] 7 [0.25] 14 [0.49] 5 [0.18] 58 [2.05] 67 [2.36] 76 [2.68] 85 [3.00] 18 [0.63] 36 [1.27] 12 [0.42] Clevis 40 [1.41] 46 [1.62] 52 [1.83] 57 [2.01] mounting type 16 [0.630] 69 [2.43] 78 [2.75] 87 [3.07] 96 [3.39] 10 [0.394] Remark: Includes mounting nut and rod end nut. -7 Cylinder with magnet − 1 [0.04] − 2 [0.07] Mounting bracket 100 − − − 20 [0.71] 1 [0.04] − − − 33 [1.16] 2 [0.07] Sensor switch ZC253□ ZC230□ ZC201□ A:20 [0.71] B:50 [1.76] A:20 [0.71] B:50 [1.76] ZC205□ 図(エア−クッシヨン仕様) Dimensions of Cylinder with Variable Cushion (mm) Bore size × ●Basic type PBDACS -M Stroke A+Stroke C+Stroke 28 20 8 15 J φU G 8 M5×0.8 M5×0.8 G1 5 2-Cushion needle N 4 4 φU φV 形 □B 外 形 Code L L K □B Width across flats AY Width across flats I 図(エア−クッシヨン仕様) A C B G G1 I J K L N U V AY 10 [0.394] 85 57 14 18 15 7 3.2 M4×0.7 M8×1 8 17 4 12 16 [0.630] 85 57 17 16.5 14.5 8 4 M5×0.8 M10×1 7 19 5 14 Bore mm [in.] ● Clevis mounting type PBDACS Bore size × Stroke -7 A+Stroke CA+Stroke CB+Stroke 15 R 5 G 8 N J φU M5×0.8 M5×0.8 2-Cushion needle 4.5 φP S φU φV 外 K □B Code L Q Width across flats I □B G1 A B G G1 I J K L N P Q R S U V CA CB 10 [0.394] 98 14 18 28 7 3.2 M4×0.7 M8×1 8 3.2 +0.09 +0.06 3.2 +0.2 +0.1 13 8 17 4 93 78 16 [0.630] 103 17 16.5 32.5 8 4 M5×0.8 M10×1 7 5 +0.09 +0.06 6.5 +0.1 +0.2 18 10 19 5 95 80 Bore mm [in.] MADE TO ORDER PEN CYLINDERS Linear Bearing Type Cylinders Symbol ●For delivery, consult us. Bore Size and Stroke Specifications mm [in.] Bore size mm [in.] Item 10 [0.394] 16 [0.630] Operation type Double acting type Mounting type See the table at lower right. Air Media Operating pressure range MPa [psi.] 0.12〜0.7 [17〜102] Proof pressure 0.1〜0.7 [15〜102] Bore size Standard strokes Maximum Stroke available stroke tolerance Note 10 25, 50, 75, 100 300 16 25, 50, 75, 100 500 +1.5 +0 [ +0.059 ] +0 Note: For non-standard strokes, consult us. 1.05 [152] MPa [psi.] 0〜70 [32〜158] Operating temperature range °C [°F] Mounting Type 50〜750 [2.0〜29.5] Operating speed range mm/s [in./sec.] Cushion Fixed type (Rubber bumper) Lubrication Not required Port size M5×0.8 Name Remark 1 Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping 7 Clevis type (with pin) Assembled and shipped Clevis type with supporting bracket (with pin) Supporting bracket included at shipping Mounting type 7-7C Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAA S 10×25 − M − − − Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Bore size × Stroke S DAA Lead wire length A 1000mm [39in.] B 3000mm [118in.] Cylinder with magnet (Magnet is standard equipment) Double acting single rod, linear bearing type Pen cylinder series Rod end accessory (Included at shipping) Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● As for the cylinder joints and the cylinder rod ends, order separately. Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mounting type (Brackets included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Not available for clevis mounting type) 1A Single foot mounting type Note 3 Flange mounting type 7 Clevis mounting type (with pin) 7-7C Clevis mounting type with supporting bracket (with pin) Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Head cover piping specification M Lateral piping with mounting thread (Not available for clevis mounting type) Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !2 !4 !1 e !5 u o q r !0 yt i !3 ●Clevis mounting type (-7) Materials No. Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod Steel t t Piston Aluminum alloy y y Magnet Plastic magnet u u Washer Mild steel i i Piston seal o o Rod seal !0 !0 Bumper !1 !1 Mounting nut !2 !2 Rod end nut Mild steel (nickel plated) !3 !3 Tube gasket Synthetic rubber (NBR) !4 !4 Snap ring Steel !5 !5 Linear bearing − w w Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Brass (nickel plated) Mass g [oz.] Bore size mm [in.] Additional mass Stroke mm Mounting type -7 Cylinder with magnet − 1 [0.04] − 2 [0.07] Mounting bracket -1A -3 25 50 75 100 48 [1.69] 54 [1.90] 59 [2.08] 65 [2.29] 95 [3.35] 106 [3.74] 117 [4.13] 127 [4.48] 38 [1.34] 76 [2.68] 25 [0.88] Clevis 52 [1.83] 58 [2.05] mounting type 16 [0.630] 106 [3.74] 117 [4.13] 63 [2.22] 69 [2.43] − − − 20 [0.71] 1 [0.04] 128 [4.51] 138 [4.87] − − − 33 [1.16] 2 [0.07] 10 [0.394] Basic type 16 [0.630] 10 [0.394] -1 19 [0.67] 38 [1.34] 10 [0.35] Sensor switch ZC253□ ZC230□ ZC201□ ZC205□ A:20 [0.71] B:50 [1.76] A:20 [0.71] B:50 [1.76] Remark: Includes mounting nut and rod end nut. Allowable Lateral Load Deflection at the End of the Piston Rod ● Keep the lateral load applied on the end of the piston rod below the values in the graph. ● Deflection at the end of the piston rod with a non-load state does not exceed the values in the graph. 0.5 3.92 0.4 φ16 Deflection (mm) Lateral load (N) 2.94 1.96 0.3 φ10 φ16 0.2 φ10 0.98 0.1 0 50 100 150 Stroke(mm) 0 50 100 150 Stroke(mm) 1N = 0.2248lbf. 1mm = 0.0394in. 1mm = 0.0394in. Dimensions of Linear Bearing Type Cylinder (mm) Bore size × ●Basic type PBDAAS -M Stroke A+Stroke C+Stroke D E F 5 10 9 4.5 M5×0.8 M5×0.8 N 5 φV J G K L L Width across flats B Width across flats I Width across flats AY Width across flats AY 外 形 図(リニアベアリングノーズ形) Code A C B D E F G I J K L N V AY 10 [0.394] 78 52 14 26 12 10 14 7 3.2 M4×0.7 M12×1 9.5 4 17 16 [0.630] 94 62 19 32 15 12 22 8 4 M5×0.8 M16×1 17.5 6 20 Stroke -7 Bore mm [in.] ● Clevis mounting type PBDAAS Bore size × A+Stroke CA+Stroke D R CB+Stroke E F G M5×0.8 M5×0.8 N 4.5 S φP J φU φV φU K □B Code Q L Width across flats I □B G1 A B D E F G G1 I J K L R S U V CA CB 10 [0.394] 91 14 26 12 10 14 22 7 3.2 M4×0.7 M12×1 9.5 3.2 +0.06 3.2 +0.1 +0.09 +0.2 13 8 17 4 86 74 16 [0.630] 112 19 32 15 12 22 27 8 4 M5×0.8 M16×1 17.5 5 +0.09 +0.06 6.5 +0.1 +0.2 18 10 22 6 104 89 Bore mm [in.] N P Q MADE TO ORDER PEN CYLINDERS Cylinders with Speed Controllers Symbol ●For delivery, consult us. Bore Size and Stroke Specifications mm [in.] Bore size mm [in.] Item 10 [0.394] Bore size 16 [0.630] Operation type Double acting type Mounting type See the table at lower right. Air Media 0.1〜0.7 [15〜102] Operating pressure range MPa [psi.] Proof pressure 1.05[152] MPa [psi.] Operating temperature range °C [°F] 0〜70 [32〜158] Operating speed range mm/s [in./sec.] 50〜300 [2.0〜11.8] Cushion Fixed type (Rubber bumper) Lubrication Not required Port size M5×0.8 Standard strokes Note Maximum available stroke Stroke tolerance 10 15, 30, 45, 60 150 +1.5 +0 +0.059 [ +0 ] 16 15, 30, 45, 60 200 +1.5 +0 +0.059 [ +0 ] Note: For non-standard strokes, consult us. Mounting type Name Remark Double foot type Included at shipping 1A Single foot type Note Included at shipping 3 Flange type Included at shipping 7 Clevis type (with pin) Assembled and shipped Clevis type with supporting bracket (with pin) Supporting bracket included at shipping Mounting type 1 7-7C Note: When the stroke exceeds 60mm, use the double foot type for the foot bracket. Order Codes PB DAU 10×30 − − − − Number of sensor switches 1 With 1 sensor switch 2 With 2 sensor switches 3 With 3 sensor switches ⁝ ⁝ Bore size × Stroke Cylinder specification Blank Standard cylinder S Cylinder with magnet DAU Double acting single rod cylinder with speed controller Pen cylinder series Rod end accessory Blank No rod end accessory I With I type knuckle Y With Y type knuckle (with pin) ● For bore sizes of φ10 and φ16 only. ● As for the cylinder joints and the cylinder rod ends, order separately. Lead wire length A 1000mm [39in.] B 3000mm [118in.] Sensor switch Blank No sensor switch ZC253 3-lead wire, solid state type ZC230 2-lead wire, solid state type ZC201 2-lead wire, reed switch type ZC205 2-lead wire, reed switch type ●For details, see p.1544. Mounting type (Brackets included at shipping other than clevis mounting type) Blank Basic type 1 Double foot mounting type (Mountable only on head cover -M specification) 1A Single foot mounting type Note 3 Flange mounting type 7 Clevis mounting type (with pin) 7-7C Clevis mounting type with supporting bracket (with pin) Note: When the stroke exceeds 60mm, use the double foot mounting type for the foot bracket. Head cover piping specification (Not available for clevis mounting type) A Lateral piping M Lateral piping with mounting thread Inner Construction (cannot be disassembled) Major Parts and Materials ●Double acting type !1 r !0 qi !3 !4 e o y tu !2 !4 w ●Clevis mounting type (-7) w No. Parts q q Rod cover w w Head cover e e Cylinder tube r r Piston rod t t Piston Aluminum alloy (nickel plated) y y Magnet Note Plastic magnet u u Piston seal i i Rod seal o o Bumper !0 !0 Mounting nut !1 !1 Rod end nut !2 !2 Housing Brass (nickel plated) !3 !3 Needle Stainless steel !4 !4 Check seal Synthetic rubber (NBR) Materials Aluminum alloy (nickel plated) Stainless steel Synthetic rubber (NBR) Mild steel (nickel plated) Note: For cylinders with magnets. Standard cylinders do not have a built-in magnet for the sensor switch. w ●Lateral piping with mounting thread (-M) Mass g [oz.] Bore size mm [in.] Stroke mm Mounting type 16 [0.630] Basic type Mounting bracket -7C Cylinder with magnet 33.8 [1.192] 37.5 [1.322] 40.1 [1.414] 44.6 [1.573] 7 [0.25] 14 [0.49] 5 [0.18] − 1 [0.04] 54.5 [1.922] 60 [2.116] 65.3 [2.303] 70 [2.469] 18 [0.63] 36 [1.27] 12 [0.42] − 2 [0.07] 15 10 [0.394] Additional mass 30 45 60 37.8 [1.333] 41.5 [1.464] 44.1 [1.556] 48.6 [1.714] Clevis 16 [0.630] mounting type 65.5 [2.310] 71 [2.504] 76.3 [2.691] 81 [2.857] 10 [0.394] -1A -1 -3 − − − 20 [0.71] 1 [0.04] − − − 33 [1.16] 2 [0.07] − 1 [0.04] − 2 [0.07] 10 [0.394] Lateral piping with 36.8 [1.298] 40.5 [1.429] 43.1 [1.520] 47.6 [1.679] 7 [0.25] 14 [0.49] 5 [0.18] 16 [0.630] mounting thread 59.5 [2.099] 65 [2.293] 70.3 [2.480] 75 [2.646] 18 [0.63] 36 [1.27] 12 [0.42] Remark: Includes mounting nut and rod end nut. Sensor switch ZC253□ ZC230□ ZC201□ ZC205□ A:20 [0.71] B:50 [1.76] 図(スピコン付) Dimensions of Cylinder with Speed Controllers (mm) Bore size × ●Basic type PBDAU Stroke -A A+Stroke C+Stroke 28 20 8 15 J 14 M5×0.8 M5×0.8 4.5 2-Speed control needle N 4 φV φU G L K □B Width across flats I Width across flats AY ● Lateral piping with mounting thread (-M) Bore size × Stroke -M PBDAU A+Stroke M5×0.8 14 4.5 形 φU 図(スピコン付) Code L □B A C B G I J K L N U V AY 10 [0.394] 84 56 14 18 7 3.2 M4×0.7 M8×1 7.5 17 4 12 16 [0.630] 84.5 56.5 17 16.5 8 4 M5×0.8 M10×1 7 19 5 14 Stroke -7 Bore mm [in.] ● Clevis mounting type PBDAU Bore size × A+Stroke CA+Stroke CB+Stroke 15 R 5 N J φU M5×0.8 2-Speed control needle G 8 M5×0.8 4.5 φP S φU φV 外 8 4 K □B Code L Q Width across flats I □B G1 A B G G1 I J K L N P Q R S U V CA CB 10 [0.394] 97 14 18 27 7 3.2 M4×0.7 M8×1 7.5 3.2 +0.09 +0.06 3.2 +0.2 +0.1 13 8 17 4 92 77 16 [0.630] 102.5 17 16.5 32 8 4 M5×0.8 M10×1 7 5 +0.09 +0.06 6.5 +0.1 +0.2 18 10 19 5 94.5 79.5 Bore mm [in.] SENSOR SWITCHES Solid State Type, Reed Switch Type Symbol Order Codes for Sensor Switches ●Sensor switches (with mounting band) − − − C1 − PBDAS Cylinder type PBDAS ●Mounting band only PBDAS Bore size 6 φ6 [0.236in.] 10 φ10 [0.394in.] 16 φ16 [0.630in.] Bore size 6 φ6 [0.236in.] 10 φ10 [0.394in.] 16 φ16 [0.630in.] Lead wire length A 1000mm [39in.] B 3000mm [118in.] Sensor switch ZC230 Solid state type with indicator lamp DC10〜28V ZC253 Solid state type with indicator lamp DC4.5〜28V DC5〜28V ZC201 Reed switch type without indicator lamp AC85〜115V ZC205 Reed switch type with indicator lamp DC10〜28V For clean systems Blank For standard cylinders CS For clean systems ●For details of sensor switches, see p.1544. Cylinder type PBDAS Mounting bracket type For clean systems Blank For standard cylinders CS For clean systems Minimum Cylinder Strokes When Mounting Sensor Switches Depending on the sensor switch type and quantity, as well as on the mounting position, the minimum cylinder strokes that allow sensor switch mounting are shown below. ●Two pieces mounting ●One piece mounting ●When mounted in-line ● When mounted in staggered positions mm Sensor switch model ZC230□, ZC253□ ZC201□, ZC205□ 2 pcs. mounting Along a straight line In staggered positions 1 pc. mounting 5 30 5 10 Sensor Switch Operating Range, Response Differential, and Maximum Sensing Location ●Operating range: R The distance the piston travels in one direction, while the switch is in the ON position. ●Response differential: C The distance between the point where the piston turns the switch ON and the point where the switch is turned OFF as the piston travels in the opposite direction. Sensor switch Magnet R mm [in.] Bore size ZC230□, ZC253□ ZC201□, ZC205□ Operating range Response differential Operating range Response differential 6 [0.236] 1.5〜2.5 [0.059〜0.098] 0.3 [0.012] or less 4〜6 [0.157〜0.236] 1.4 [0.055] or less 10 [0.394] 2.0〜3.0 [0.079〜0.118] 0.3 [0.012] or less 4〜6 [0.157〜0.236] 1.5 [0.059] or less 16 [0.630] 2.5〜3.5 [0.098〜0.138] 0.3 [0.012] or less 5〜7 [0.197〜0.276] 1.8 [0.071] or less ON OFF C (Response differential) R OFF ON C (Response differential) Note: The operating range and response differential are to be used as reference values. Maximum sensing location Mounting Location of End of Stroke Detection Sensor Switch When the sensor switch is mounted in the location shown in the diagram (figures in the table are reference values), the magnet comes to the sensor switch’s maximum sensing location at the end of the stroke. ●Double acting type A ●Single acting pull type B A B mm [in.] mm [in.] Bore size Bore size Sensor switch model ZC230□ ZC253□ ZC201□ ZC205□ 6 [0.236] 10 [0.394] 16 [0.630] Code A 31. [0.118] 3.5 [0.138] 4.5 [0.177]– B 0.5 [0.020] –4.5 [–0.177] –3.5 [–0.138]– A 4.5 [0.177] 5.5 [0.197] 6.5 [0.236]– B 11. [0.039] –3.5 [–0.118] –2.5 [–0.079]– A 11. [0.039] 1.5 [0.059] 2.5 [0.098]– B 1.5 [0.059] –3.5 [–0.138] –2.5 [–0.098]– ●Single acting push type A B A B 6 [0.236] 10 [0.394] 16 [0.630] 3 [0.118] 8.5 [0.335] 9.5 [0.374] 16〜30 8 [0.315] 13.5 [0.531] 14.5 [0.571] 31〜60 23 [0.906] 23.5 [0.925] 24.5 [0.965] − 0〜15 ZC201□ A B ZC205□ A 0.5 [0.020] –4.5 [–0.177] –3.5 [–0.138] 4.5 [0.177] 10 [0.394] 11 [0.433] 16〜30 9.5 [0.374] 15 [0.591] 16 [0.630] 31〜60 24.5 [0.965] 25 [0.984] 26 [1.024] − 2 [0.079] –3 [–0.118] –2 [–0.079] 0〜15 1 [0.039] 6.5 [0.256] 7.5 [0.295] 16〜30 31〜60 B B A ZC201□ B B 6 [0.236] 10 [0.394] 16 [0.630] Stroke − 31. [0.118] 3.5 [0.138] 4.5 [0.177] 0〜15 0.5 [0.020] 0.5 [0.020] 1.5 [0.059] 16〜30 5.5 [0.217] 5.5 [0.217] 6.5 [0.256] − 4.5. [0.177] 5.5. [0.197] 6.5. [0.236] 0〜15 21. [0.079] 21. [0.079] 31. [0.118] 16〜30 7.5 [0.276] 7.5 [0.276] 8.5 [0.315] − 1.5 [0.039] 1.5 [0.059] 2.5 [0.098] 0〜15 1.5 [0.059] 1.5 [0.059] 2.5 [0.098] 16〜30 6.5 [0.256] 6.5 [0.256] 7.5 [0.295] ●Variable cushion type, linear bearing type, and with speed controller type A B Stroke 0〜15 ZC230□ ZC253□ A ZC230□ ZC253□ ZC205□ mm [in.] Code Code A Bore size Sensor switch model Sensor switch model − 6 [0.236] 21 [0.827] 11.5 [0.453] 12.5 [0.492] 21.5 [0.846] 22.5 [0.886] 1.5 [0.059] –3.5 [–0.138] –2.5 [–0.098] (Illustration shows “ with speed controller type.”) mm [in.] Bore size Sensor switch model ZC230□ ZC253□ ZC201□ ZC205□ 10 [0.394] Note 16 [0.630] A 2 [0.079] 3 [0.118] B 5 [0.197] 6 [0.236] A 3.5 [0.138] 4.5 [0.177] B 6.5 [0.256] 7.5 [0.295] A 0 1 [0.039] B 3 [0.118] 4 [0.157] Code Note: For φ10, always mount so that the indicator lamp is on the cover side and the lead wires are on the inner side, as shown in the diagram. Mounting Sensor Switch by Strokes Moving Sensor Switch ●5mm stroke ●Loosening the mounting screw allows the sensor switch to be moved either along the axial or circumference direction of the cylinder. ●When making fine adjustments of the sensor switch along the axial direction, a very slight loosening of the mounting screw (about onehalf turn) is enough to allow the sensor switch to be moved. ●Tighten the mounting screw with a tightening torque of 0.3N·m [2.7in·lbf] or less. Mounting screw ●10mm stroke Sensor band Sensor switch Sensor holder Cylinder tube Position of sensor holder, and how to adjust it ●The sensor holder cannot be installed at the center of the sensor switch when mounting 2 sensor switches on a 5mm stroke cylinder. ●When mounting 2 sensor switches on a 5mm stroke cylinder, loosen the mounting screw and move the sensor switch until the sensor holder is in the position shown in the diagram, and install it in the specified position. ●For 10mm strokes or more, install the sensor holder so that it is approximately in the center of the sensor switch, as shown in the diagram. ● Caution when installing cylinder with sensor switch Model marking surface In the ZC type sensor switches, the opposite side from the model marking surface is the sensing surface side. Mount it so that the cylinder magnet comes to the sensing surface side. Sensing surface Dimensions of Sensor Switch Mounting (mm) Y 10.2 mm [in.] Bore Code Y 6 [0.236] (16 [0.630]) 10 [0.394] (18 [0.709]) 16 [0.630] (21 [0.827]) MOUNTING BRACKETS, ROD END ACCESSORIES Dimensions of Mounting Bracket (mm) ● Single foot bracket (For the order code, see p. 311.) ● Flange bracket (For the order code, see p. 311.) φU AT AH BC BP LY φU AE BF BT AG AD AP BE AF Code Code Type Bore mm [in.] U AD AE AF AG AH AP AT LY 6 [0.236] 6 5 32 22.2 7 9 4.2 1.6 16 10 [0.394] 8 5 32 22.2 7 9 4.2 1.6 16 16 [0.630] 10 6 42 29.2 9 14 5.2 2.3 24 Nonrotating 10 [0.394] 10 6 42 29.2 9 14 5.2 2.3 24 16 [0.630] 12 6 42 29.2 9 14 5.2 2.3 24 Linear bearing 10 [0.394] 12 5 35 25 13 16 4.5 2.3 26 16 [0.630] 16 6 44 32 13 20 5.5 3.2 33 6 [0.236] 8 5 32 22.2 7 9 4.2 1.6 16 10 6 42 29.2 9 14 5.2 2.3 24 12 6 42 29.2 9 14 5.2 2.3 24 Standard Clean 10 [0.394] systems 16 [0.630] CC CD CG CB CU ● Clevis mount supporting bracket Order code: 7C-PBDA Bore size CA CY CX CR □12 CZ CQ±0.05 φCP±0.05 CF CE CW CT CV CK CL Code CK CA CB CC CD CE CF CG (Hexagon socket head bolt) 10 [0.394] 20 11 22 5 40 30.2 12 M4×0.7×10 16 [0.630] 24 14 28 6 48 35.2 16 M5×0.8×10 Bore mm [in.] Code Bore mm [in.] CL (Spring washer) CP CQ CR CT CU CV CW CX CY CZ 10 [0.394] Nominal 4 3.3 3.1 21 7 36 16 [0.630] Nominal 5 5.1 6.4 14 2.3 5.2 20 10 25 9 2 4.2 18 8 7 42 Type Bore mm [in.] U BC BE BF BP BT 6 [0.236] 6 14 32 22.2 4.2 1.6 10 [0.394] 8 14 32 22.2 4.2 1.6 16 [0.630] 10 20 42 29.2 5.2 2.3 Nonrotating 10 [0.394] 10 20 42 29.2 5.2 2.3 16 [0.630] 12 20 42 29.2 5.2 2.3 Linear bearing 10 [0.394] 12 20 40 30 4.5 2.3 16 [0.630] 16 26 52 40 5.5 3.2 6 [0.236] 8 14 32 22.2 4.2 1.6 10 20 42 29.2 5.2 2.3 12 20 42 29.2 5.2 2.3 Standard Clean 10 [0.394] systems 16 [0.630] PBDAI ●I type knuckle R12 s 5 PA 8 NA NP +0.06 Code NA NB NC 10 [0.394] 21 Insertion 0.4 NB NK PQ NK NC +0.2 0 Bore mm [in.] φPC PB NA +0.09 NQ +0.2 0 □12 7 NB NQ±0.05 +0.09 NP +0.06 PJ 7 45° □12 pheri c radiu al s □12 pheri c radiu al s 8 R12 s 5 PBDAY ●Y type knuckle φPP +0.03 0 Dimensions of Pin Bracket (mm) Dimensions of Rod End Accessories (mm) NC +0.2 0 NK NP NQ Mass g [oz.] (with pin) 8 10 M4×0.7 3.2 3.2 21 [0.74] 16 [0.630] 21 11 10 M5×0.8 5 6.5 15 [0.53] Code Bore mm [in.] 10 [0.394] 21 16 [0.630] 25 Mass g [oz.] PA PB PC PJ PP 9 M4×0.7 3.2 3.1 16 [0.56] 10 [0.394] 17 5 14 13.5 3.2 (15) 2 [0.07] 14 M5×0.8 5 16 [0.630] 17 5 14 13.5 16 [0.630]※ 19 6 19 19 8 8 Code Mass NP NQ g [oz.] Bore mm [in.] NA NB NC NK 6.4 22 [0.78] 5 PQ (15) 3 [0.11] (20.5) Note: ※shows for clevis mounting bracket use. Order Codes for Mounting Brackets and Rod End Accessories (1) Single foot bracket Note: Rod end accessories are not available for clean systems. (5) Y type knuckle − 1A − Y Bore size 6 -φ 6 (PBDA only) 10 -φ10 16 -φ16 Single foot bracket − PBDA Pen cylinder series Applicable type PBDA (Except for linear bearing, non-rotating types) PBDAA (Linear bearing type) Note PBDAL (Non-rotating type) Note Y type knuckle Bore size 10 -φ10 16 -φ16 For clean systems Blank For standard cylinders CS For clean systems Note: Not available for clean systems. (6) I type knuckle (2) Double foot bracket (2 foot brackets in 1 set) − 1 − I − PBDA Bore size 10 -φ10 16 -φ16 Double foot bracket Pen cylinder series Applicable type PBDA (Except for linear bearing, non-rotating types) PBDAA (Linear bearing type) Note PBDAL (Non-rotating type) Note Bore size 10 -φ10 16 -φ16 I type knuckle For clean systems Blank For standard cylinders Note: Not available for clean systems. CS For clean systems (3) Flange bracket − 3 (7) Pin bracket − PK Bore size 6 -φ 6 (PBDA only) 10 -φ10 16 -φ16 Flange bracket Applicable type PBDA (Except for linear bearing type) PBDAA (Linear bearing type) For clean systems Blank For standard cylinders CS For clean systems (4) Clevis mount supporting bracket − 7C − PBDA Clevis mount supporting bracket Pen cylinder series For clean systems Blank For standard cylinders CS For clean systems Bore size 10 -φ10 16 -φ16 − PBDA Pen cylinder series Pin bracket Pin bracket type 3: For φ10 Y type knuckle, φ10 clevis mounting bracket 5: For φ16 Y type knuckle 6: For φ16 clevis mounting bracket ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Single acting push type
- Non-rotating
- Various mounting options
- High-quality seals
- Cushion mechanism
- Pressure range: 0.34-0.7 MPa
- Temperature range: 0-60 °C
Frequently asked questions
The PBSAL is available in several mounting options: Basic, single foot, double foot, and flange type. For more details, please consult the dimensions table.
The PBSAL's operating pressure range is 0.34 to 0.7 MPa (49 to 102 psi).
No, lubrication is not required for the PBSAL. However, if lubrication is needed, use Turbine Oil Class 1 (ISO VG32) or equivalent. Avoid using spindle oil or machine oil.
The cushion mechanism is designed to reduce as much as possible the impact of pistons with high kinetic energy when they stop at the end of the stroke, thus reducing impact noise during high-speed operations.