KTR MINEX-S Operating/Mounting Instructions
KTR MINEX-S is a permanent-magnetic synchronous coupling designed for transmitting torque without contact. It utilizes magnetic forces to separate the product space reliably from the atmosphere, making it suitable for pumps, agitators, and other applications requiring containment. This type of coupling is available with containment shrouds made from stainless steel or Hastelloy®, offering high levels of resistance to pressure and temperature.
PDF
Download
Document
Advertisement
Advertisement
MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions KTR-N Sheet: Edition: 46510 EN 1 of 22 10 These operating/assembly instructions exclusively apply for those types of MINEX®-S with containment shroud made of stainless steel or Hastelloy®. MINEX®-S Permanent-magnetic coupling with containment shroud made of stainless steel or Hastelloy® according to directive 2014/34/EU Size SA 22/4 to SB 60/8 Size SA 75/10 to SF 250/38 MINEX®-S is a permanent-magnetic synchronous coupling which is able to transmit torques without contact through magnetic forces. Being used in pumps and agitators, it separates the product space reliably from the atmosphere. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions KTR-N Sheet: Edition: 46510 EN 2 of 22 10 Table of contents 1 2 3 4 Technical data 3 1.1 1.2 3 6 Sizes and dimensions Selection data Advice 6 2.1 2.2 2.3 2.4 2.5 2.6 6 6 7 7 8 8 General advice Safety and advice symbols General hazard warnings Intended use Reference to EC Machinery Directive 2006/42/EC Hints on couplings Storage, transport and packaging 8 3.1 3.2 8 8 Storage Transport and packaging Assembly 4.1 4.2 4.3 4.4 4.5 4.6 4.7 9 Components of MINEX®-S Advice for finish bore Advice on driving and driven shaft Assembly of internal and external rotor Assembly of containment shroud Displacements - alignment of the couplings Disassembly 9 10 11 11 12 13 14 5 Start-up 14 6 Breakdowns, causes and elimination 16 7 Environment and disposal 17 7.1 7.2 Environment Disposal 17 17 8 Maintenance and service 18 9 Spares inventory, customer service addresses 18 10 Enclosure A Advice and instructions regarding the use in 10.1 Intended use in potentially explosive atmospheres potentially explosive atmospheres 10.2 Inspection intervals for couplings in 10.3 Temperature monitoring in 10.4 marking of coupling for potentially explosive atmospheres 10.5 Certificate of conformity Please observe protection note ISO 16016. Drawn: Verified: 19 potentially explosive atmospheres potentially explosive atmospheres 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: 19 19 20 21 22 KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 1 KTR-N Sheet: Edition: 46510 EN 3 of 22 10 Technical data 1.1 Sizes and dimensions Illustration 1: MINEX®-S SA 22/4 to SB 60/8 Table 1: Dimensions - SA 22/4 to SB 60/8 with containment shroud made of stainless steel Size SA 22/4 SA 34/10 SA 46/6 SA 60/8 SB 60/8 TK max [Nm] with ~20 °C 0.15 1 3 7 14 Dimensions [mm] Internal rotor Finish bore 1) di Min. Max. 5 9 5 12 8 16 12 22 DI1 LI1 20 20 28 35 36 20 22 33 36.3 56 Containment shroud SI Min. 2.0 2.0 6.5 1.7 0.0 Max. 2.0 5.5 7.0 5.5 4.0 GI DS1 DS2 DS3 DS4 ZS LS M3 M3 M4 21.5 34 46 38 46 64 46 55 78 4.5 4.5 4.5 8 4 8 M5 59 75 89 5.5 8 29 30.5 45 50 70.3 Dimensions [mm] Size SA 22/4 SA 34/10 SA 46/6 SA 60/8 SB 60/8 External rotor Finish bore 1) da Min. Max. 5 11 5 14 5 24 9 32 9 38 General DA1 DA3 LA1 LA2 LA3 GA S 18 22 40 38 53 69.5 94.5 8.5 10.5 16 19 15 11 13 22 28 30 M4 M4 M5 M6 M8 5.0 5.3 9.0 50 35 38.8 53 66 93.3 12.0 Ltotal Min. 42 46 69 80 105.2 Max. 42 49.5 69.5 83.3 109.2 1) Bores H7 with keyway to DIN 6885 sheet 1 [JS9] and setscrew Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 1 KTR-N Sheet: Edition: 46510 EN 4 of 22 10 Technical data 1.1 Sizes and dimensions Illustration 2: MINEX®-S SA 75/10 to SF 250/38 Table 2: Dimensions - SA 75/10 to SF 250/38 with containment shroud made of stainless steel or Hastelloy® Size SA 75/10 SB 75/10 SC 75/10 SA 110/16 SB 110/16 SC 110/16 SB 135/20 SC 135/20 SD 135/20 SC 165/24 SD 165/24 SE 165/24 SD 200/30 SE 200/30 SD 250/38 SE 250/38 SF 250/38 TK max [Nm] with ~20 °C 10 24 40 25 60 95 100 145 200 210 280 370 410 530 670 820 1000 Dimensions [mm] Internal rotor Finish bore 1) di Min. Max. DI1 LI1 39.5 58 80 45 65 85 65 85 110 85 110 130 Containment shroud SI Min. 4 Max. 46.5 26.5 4.0 55.0 35.0 15.0 50.5 30.5 8.0 61.5 39.0 19.0 GI DS1 DS2 DS3 DS4 ZS LS = Ltotal 2) M6 75 100 118 9 8 102 M8 110 133 153 9 12 115 M10 135 158 178 9 16 139 M12 163. 5 192 218 11 12 170 12 32 45 14 55 80 20 70 90 24 80 110 38 90 130 135 6 24.0 M16 200 252 278 11 12 180 38 100 165 115 135 155 6 46.0 26.0 6.0 M16 255 285 315 13.5 12 182 4 4 6 1) Bores H7 with keyway to DIN 6885 sheet 1 [JS9] and setscrew 2) Total length without flange hub Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 1 KTR-N Sheet: Edition: 46510 EN 5 of 22 10 Technical data 1.1 Sizes and dimensions Page 4 continued: Illustration 2: MINEX®-S SA 75/10 to SF 250/38 Table 2: Dimensions - SA 75/10 to SF 250/38 with containment shroud made of stainless steel or Hastelloy® External rotor Size DA1 SA 75/10 SB 75/10 SC 75/10 SA 110/16 SB 110/16 SC 110/16 SB 135/20 SC 135/20 SD 135/20 SC 165/24 SD 165/24 SE 165/24 SD 200/30 SE 200/30 SD 250/38 SE 250/38 SF 250/38 90 DA2 100 DA3 110 126 135 145 150 160 170 180 188 198 LA1 41.3 61.3 83.8 41.3 61.3 81.3 70.3 90.3 110.3 90.3 110.3 130.3 GA M6 Dimensions [mm] Flange hub Max. finish bore DF1 DF2 LF1 1) d f 42 60 114 64.5 General LF2 35.5 GF M8 S 12.2 14.2 M6 55 85 150 99.5 59.5 M10 M6 70 100 170 65.5 48.5 M12 M6 75 110 198 77 60 M16 19.0 Total length 2) Min. 140 142 166.5 177.5 183.5 203.5 18.5 190.5 22.0 18.5 200.5 21.0 233 Max. 164.5 166.5 214.5 204.5 247 234 212 222 232 130.3 M6 80 120 232 120 98 M12 26.0 282 300 267 282 292 110.3 130.3 150.3 M6 100 150 300 140 93 M16 26.0 282 302 322 322 1) Bores H7 with keyway to DIN 6885 sheet 1 [JS9] and setscrew 2) Total length with flange hub Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 1 KTR-N Sheet: Edition: 46510 EN 6 of 22 10 Technical data 1.2 Selection data Perm. operating pressure: 16 bar with 300 °C 1) 16 bar with 150 °C 2) 25 bar with 300 °C 1), 3) 25 bar with 150 °C 2), 3) Higher resistances to pressure are possible on request, if required. Perm. operating temperature: 300 °C 1) / 150 °C 2) Max. speed: 3600 rpm 4) Higher speeds are possible on request, if required. 1) 2) 3) 4) Figures are valid for magnets made of Sm2Co17 Figures are valid for magnets made of NdFeB Figures are valid for containment shroud made of Hastelloy® - 1.4571 (flange) Figure is valid if metallic containment shrouds according to KTR standard are used The operation with several max. ratings at the same time must be avoided to undermine operational safety. The materials of the magnetic coupling result from the application and are bound to the order. 2 Advice 2.1 General advice Please read through these operating/assembly instructions carefully before you start up the coupling. Please pay special attention to the safety instructions! The MINEX®-S coupling is suitable and approved for the use in potentially explosive atmospheres. When using the coupling in potentially explosive atmospheres, please observe the special advice and instructions regarding safety in enclosure A. The operating/assembly instructions are part of your product. Please store them carefully and close to the coupling. The copyright for these operating/assembly instructions remains with KTR. 2.2 Safety and advice symbols STOP ! Warning of potentially explosive atmospheres This symbol indicates notes which may contribute to preventing bodily injuries or serious bodily injuries that may result in death caused by explosion. Warning of personal injury This symbol indicates notes which may contribute to preventing bodily injuries or serious bodily injuries that may result in death. Warning of product damages This symbol indicates notes which may contribute to preventing material or machine damage. General advice This symbol indicates notes which may contribute to preventing adverse results or conditions. Warning of hot surfaces This symbol indicates notes which may contribute to preventing burns with hot surfaces resulting in light to serious bodily injuries. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 2 KTR-N Sheet: Edition: 46510 EN 7 of 22 10 Advice 2.3 General hazard warnings STOP For people with pacemakers the handling of MINEX®-S is dangerous. In this case it is compulsory to meet the following measures: • • A safety distance of 2 m must be kept towards the non-assembled components of the coupling. For assembled couplings with magnetic robots aligned in axial position to each other and with an ambient housing of the coupling (bellhousing) a minimum safety distance of 0.5 m applies. A crane should be used for handling assembled drive units. With assembly, operation and maintenance of the coupling it has to be made sure that the entire drive train is secured against accidental switch-on. You may be seriously hurt by rotating parts. Please make absolutely sure to read through and observe the following safety indications. ! STOP A distance of 1 m between MINEX®-S and magnetic data carriers (bank cards, disks, etc.) must be observed. The internal and the external rotor have a strong magnetic field. Within a distance of 0.5 m around the MINEX®-S uncontrolled handling close to metallic components, sudden mutual attraction of the rotors or magnetizable components may cause injuries or damages on the parts. • Operations on the MINEX®-S are generally only permitted at standstill and with unpressurized condition. • All operations on and with the coupling have to be performed taking into account "safety first". • Please make sure to switch off the power pack before you perform your work on the coupling. • Secure the power pack against accidental switch-on, e. g. by providing warning signs at the place of switch-on or removing the fuse for current supply. • Do not reach into the operating area of the coupling as long as it is in operation. • Please secure the coupling against accidental contact. Please provide for the necessary protection devices and covers. The operator is asked to check within the scope of his safety concept as to which impacts on the environment may be associated with a failure of the magnetic coupling and which additional safety measures protecting people must be taken. In addition to the advice given in this safety data sheet the general instructions for operational safety and accident prevention must be observed. 2.4 Intended use You may only assemble, operate and maintain the coupling if you • have carefully read through the operating/assembly instructions and understood them • are technically qualified and specifically trained (e. g. safety, environment, logistics) • are authorized by your company The coupling may only be used in accordance with the technical data (see chapter 1). Unauthorized modifications on the coupling design are not admissible. We will not assume liability for any damage that may arise. In the interest of further development we reserve the right for technical modifications. The MINEX®-S described in here corresponds to the technical status at the time of printing of these operating/assembly instructions. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 2 KTR-N Sheet: Edition: 46510 EN 8 of 22 10 Advice 2.5 Reference to EC Machinery Directive 2006/42/EC The couplings supplied by KTR should be considered as components, not machines or partly completed machines according to EC Machinery Directive 2006/42/EC. Consequently KTR does not have to issue a declaration of incorporation. For details about safe assembly, start-up and safe operation refer to the present operating/assembly instructions considering the warnings. 2.6 Hints on couplings For a safe operation of the magnetic coupling a circulation of the medium ensuring permanent heat dissipation is mandatory. For dirty media containing abrasive or magnetic particles a separation in the circulation is recommended. 3 Illustration 3: Structure of MINEX®-S Storage, transport and packaging 3.1 Storage The coupling hubs are supplied in preserved condition and can be stored at a dry and covered place for 2 years. ! The storage rooms must not include any ozone-generating devices like e. g. fluorescent light sources, mercury-vapour lamps or electrical high-voltage appliances. Humid storage rooms are not suitable. Please make sure that condensation is not generated. The best relative air humidity is less than 65 %. A direct contact with metallic components must be avoided. Direct heat exposure (sun, heating) on the MINEX®-S must be avoided. With the conservation of all units having a MINEX®-S installed, the compatibility of the preservative selected with MINEX®-S materials must be checked. 3.2 Transport and packaging ! In order to avoid any injuries and any kind of damage please always make use of proper transport and lifting equipment. The couplings are packed differently each depending on size, number and kind of transport. Unless otherwise contractually agreed, packaging will follow the in-house packaging specifications of KTR. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 4 KTR-N Sheet: Edition: 46510 EN 9 of 22 10 Assembly The coupling is generally supplied in individual parts. Before assembly the coupling has to be inspected for completeness. Please make sure that the coupling components are not damaged when being unpacked. The coupling components have a strong magnetic field. ! 4.1 Components of MINEX®-S Components of MINEX®-S, size SA 22/4 to SB 60/8 Component 1 2 3 Quantity 1 1 1 4 2 Description External rotor Containment shroud Internal rotor Setscrew DIN EN ISO 4029 1) 1) with finish bored type only Illustration 4: MINEX®-S, size SA 22/4 to SB 60/8 Components of MINEX®-S, size SA 75/10 to SF 250/38 Component 1 2 3 Quantity 1 1 1 4 1 5 2) 1 Description External rotor Containment shroud Internal rotor Setscrew DIN EN ISO 4029 1) Flange hub with setscrew DIN EN ISO 4029 1) and cap screws DIN EN ISO 4762 or hexagon screw DIN EN ISO 4017 Illustration 5: MINEX®-S, size SA 75/10 to SF 250/38 1) with finish bored type only 2) only on request If KTR also supplies component 5, the following tightening torques must be considered when screwing the hub to the external rotor. The screws to be used are also part of the scope of delivery of KTR. Table 3: Tightening torques of the cap screws or hexagon screws Size Cap screw DIN EN ISO 4762 1) or hexagon screw DIN EN ISO 4017 1) Tightening torque TA [Nm] 75/10 110/16 135/20 165/24 200/30 250/38 M6 14 1) min. property class 10.9 Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 4 KTR-N Sheet: Edition: 46510 EN 10 of 22 10 Assembly 4.2 Advice for finish bore The maximum permissible bore diameters d (see chapter 1 - technical data) must not be exceeded. If these figures are disregarded, the coupling may tear. Rotating particles may cause danger to life. STOP • Hub bores machined by the customer have to observe concentricity or axial runout, respectively (see illustration 6 and 7). • Please make absolutely sure to observe the figures for Ø dmax. • Carefully align the hubs when the finish bores are drilled. • Please provide for a setscrew according to DIN EN ISO 4029 with a cup point or an end plate to fasten the hubs axially. Illustration 6: Concentricity and axial runout on external rotor Illustration 7: Concentricity and axial runout on internal rotor The customer bears the sole responsibility for all machining processes performed subsequently on unbored or pilot bored as well as finish machined coupling components and spare parts. KTR does not assume any warranty claims resulting from insufficient remachining. ! KTR supplies unbored or pilot bored coupling components and spare parts only upon explicit request of the customer. These parts are additionally marked with the symbol . Reference to unbored resp. pilot bored coupling components with explosion protection marking: Basically the company KTR supplies couplings resp. coupling hubs with explosion protection marking as an unbored or pilot bored type only on explicit request of the customer. The prerequisite is a declaration of exemption submitted by the customer assuming any responsibility and liability for remachining performed properly. Table 4: Setscrew DIN EN ISO 4029 Size 22/4 34/10 46/6 60/8 75/10 Internal rotor M5 M6 Dimension G Tightening torque TA [Nm] M3 M3 M4 1 1 1.5 Dimension G Tightening torque TA [Nm] M4 M4 M5 External rotor M6 1) M8 1) M8 2) 1.5 1.5 2 4.8 2 4.8 10 10 110/16 135/20 165/24 200/30 250/38 M8 M10 M12 M16 M16 10 17 40 80 80 M10 2) M12 2) M12 2) M12 2) M16 2) 17 40 40 40 80 1) with type SA 60/8 - M6; with type SB 60/8 - M8 2) if the flange hub is supplied by KTR Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 4 KTR-N Sheet: Edition: 46510 EN 11 of 22 10 Assembly 4.3 Advice on driving and driven shaft • When manufacturing the pump shaft and the adapter plate for the containment shroud, the concentricity and the axial runout (see illustration 8) must be observed. • Please use tolerance f7 for centering the containment shroud. • Tolerance fits and surfaces for O-rings: finely finished RZ 6.3 µm. Illustration 8: Tolerances of connection components on driven side 4.4 Assembly of internal and external rotor For the assembly we recommend to have the data sheet of the magnetic coupling available. Specifications entered in the dimensional drawing have to be primarily observed. STOP Impacts and shocks on the coupling components are not permissible. They may cause damages on the components. We recommend to inspect bores, shaft, keyway and feather key for dimensional accuracy before assembly. • Before assembly the internal and external rotor must be cleaned from magnetic dust. Recommended utilities are: Propyl alcohol and cellulose cloths (no cleaning rags). • Mount the internal and external rotor onto the shaft of driving and driven side. Heating the internal and external rotor lightly (approx. 80 °C) allows for an easier installation onto the shaft. STOP Touching the heated hubs causes burns. Please wear safety gloves. • Please observe the distance dimensions between the internal and the external rotor (SI and SI + S) and the sealing surface of the containment shroud specified in table 1 and 2. Hereby you ensure that the outer and the inner magnets are flush above each other. ! The user must ensure correct alignment of the internal rotor and the containment shroud. • Secure the rotors by tightening the setscrews acc. to DIN EN ISO 4029 (see table 4) or by using an end plate and end screw. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 4 KTR-N Sheet: Edition: 46510 EN 12 of 22 10 Assembly 4.5 Assembly of containment shroud • Put the O-ring or the flat seal - each depending on the design - into the adapter flange or the mounting groove of the containment shroud. The material must be resistant to the intended operating conditions (medium, temperature). • Push the containment shroud over the internal rotor and screw it to the adapter flange. For fastening the containment shroud to the adapter flange use cap screws according to table 5 and tighten at the tightening torques specified. • Tighten the cap screws evenly crosswise gradually in several revolutions to the tightening torque specified in table 5. Repeat this process until the full tightening torque has been achieved with all cap screws. Table 5: Tightening torques for cap screws from V2A-70 - DIN EN ISO 4762 Size Thread z = number 22/4 34/10 46/6 60/8 75/10 M4 M4 M4 M5 M8 8 8 8 8 8 TA [Nm] 2.6 2.6 2.6 5.1 21 Size Thread z = number 110/16 135/20 165/24 200/30 250/38 M8 M8 M10 M10 M12 12 16 12 12 12 TA [Nm] 21 21 41 44 74 • The user has to ensure venting or draining of the internal space of the containment shroud himself. • Please make sure that driving and driven side are slowly connected to prevent the external rotor from striking against the containment shroud. STOP There is the danger of squeezing if the magnets of internal and external rotor are tightened suddenly. • Please make sure that there is a radial direction with the assembly because the external rotor must not touch the containment shroud. ! Do not damage the external rotor and the containment shroud during the assembly. • Fill the machine and containment shroud fully with one medium during standstill. • Please carefully vent the containment shroud and the circulation cycle. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 4 KTR-N Sheet: Edition: 46510 EN 13 of 22 10 Assembly 4.6 Displacements - alignment of the couplings The displacement figures specified in table 6 provide for sufficient safety to compensate for external influences like, for example, thermal expansion or foundation settling. In order to ensure a long service life of the coupling and avoid dangers with the use in potentially explosive atmospheres, the shaft ends must be accurately aligned. Please absolutely observe the displacement figures specified (see table 6). If the figures are exceeded, the coupling will be damaged. The more accurate the alignment of the coupling, the longer is its service life. If used in potentially explosive atmospheres for explosion group IIC, only half of the displacement figures (see table 6) are permissible. ! Please note: • The displacement figures specified in table 6 are maximum figures which must not arise in parallel. If radial and angular displacements arise at the same time, the permissible displacement values may only be used proportionally (see illustration 10). • Please inspect with a dial gauge, ruler or feeler gauge whether the permissible displacement figures of table 6 can be observed. Angular displacement Radial displacement Kw = SA2 - SA1 [mm] Examples of the displacement combinations specified in illustration 10: Axial displacement Illustration 9: Displacements Illustration 10: Combinations of displacement Example 1: Kr = 30 % Kw = 70 % Example 2: Kr = 60 % Kw = 40 % Ktotal = Kr + Kw 100 % Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 4 KTR-N Sheet: Edition: 46510 EN 14 of 22 10 Assembly 4.6 Displacements - alignment of the couplings Table 6: Displacement figures Max. angular displacement Kw [degree] Kw [mm] 1.68 1.11 1.92 1.78 0.88 1.07 1.52 2.48 0.80 1.32 1.60 3.07 0.80 1.54 0.56 1.08 1.28 3.24 0.64 1.62 0.48 1.21 0.88 2.61 0.56 1.66 0.40 1.19 0.48 1.66 0.40 1.38 0.32 1.11 0.40 1.62 0.32 1.30 0.38 1.92 0.31 1.56 0.26 1.32 Size SA 22/4 SA 34/10 SA 46/6 SA 60/8 SB 60/8 SA 75/10 SB 75/10 SC 75/10 SA 110/16 SB 110/16 SC 110/16 SB 135/20 SC 135/20 SD 135/20 SC 165/24 SD 165/24 SE 165/24 SD 200/30 SE 200/30 SD 250/38 SE 250/38 SF 250/38 Max. radial displacement Kr [mm] 0.30 0.29 0.19 Max. axial displacement Ka [mm] 0.37 0.40 0.32 ±1 0.42 0.37 0.39 4.7 Disassembly If you disassemble the magnetic coupling, please absolutely observe the instructions that apply for handling hazardous substances and the accident prevention regulations. In case of doubt, please gather the necessary information before disassembly. ! Please observe the warnings and safety instructions. The disassembly of the magnetic coupling is made in the reverse order of the assembly. 5 Start-up Before start-up of the coupling, inspect tightening of the setscrews in the hubs, the alignment and adjust, if necessary, and also inspect all screw connections for the tightening torques specified. If used in potentially explosive atmospheres the setscrews to fasten the hubs as well as all screw connections must be secured against working loose additionally, e. g. conglutinating with Loctite (average strength). Finally the coupling protection against accidental contact must be fitted. It is required in accordance with DIN EN ISO 12100 (Safety of Machinery) and directive 2014/34/EU and must protect against • access with a little finger • falling down of solid foreign objects. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 5 KTR-N Sheet: Edition: 46510 EN 15 of 22 10 Start-up The cover may provide for openings intended for necessary heat dissipation. These openings have to comply with DIN EN ISO 13857. The cover and the containment shroud must be electrically conductive and included in the equipotential bonding. Bellhousings (magnesium share below 7.5 %) made of aluminium and damping rings (NBR) are permitted as connecting element between pump and electric motor. The cover may only be taken off with standstill of the unit. • With start-up and after a longer period of standstill it must be tested (by rotating the driving shaft manually) if coupling and power pack can easily be rotated. • After a short initial operation the venting process must be repeated several times with standstill of the machine. ! The MINEX®-S must never be used with dry operation over a longer period. Please note: In general the internal and the external rotor of the magnetic coupling must always run synchronously. The operation in a „torn condition " over a longer period of time must be avoided. After switching off the engine the coupling synchronizes again and is able to transmit the full power. Before longer periods of standstill liquids tending to solidification, efflorescence, polymerization etc. must be drained from the machine and the containment shroud. If necessary, they must be flushed with a suitable liquid. A troublefree operation of the MINEX®-S can be expected if you observe the maximum ratings of operation and the hints given in these instructions. For covers with unlocked openings on the top face no light metals must be used if the couplings are used as equipment of equipment group ll (if possible, from stainless steel). During operation of the coupling, please pay attention to • different operating noise • vibrations occurring. ! If you note any irregularities with the coupling during operation, the drive unit must be switched off immediately. The cause of the breakdown must be specified by means of the table „Breakdowns“ and, if possible, be eliminated according to the proposals. The potential breakdowns specified can be hints only. To find out the cause all operating factors and machine components must be considered. Coating of coupling: If coated (priming, paintings, etc.) couplings are used in potentially explosive atmospheres, the requirements on conductibility and coating thickness must be considered. With paintings up to 200 µm electrostatic load does not have to be expected. Paintings and coatings exceeding a thickness of 200 µm are generally impermissible for potentially explosive atmospheres. It also applies for multiple coatings exceeding an overall thickness of 200 µm. Make sure with painting or coating that the coupling components are conductively connected with the device/devices to be connected so that the equipotential bonding is not impeded by the paint or coat applied. In addition, make sure that the marking of the coupling remains legible. Painting or coating of the containment shroud is generally not admitted. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 6 KTR-N Sheet: Edition: 46510 EN 16 of 22 10 Breakdowns, causes and elimination The below-mentioned failures can result in a use of the MINEX®-S coupling other than intended. In addition to the specifications given in these operating/assembly instructions make sure to avoid such failures. The errors listed can only be clues to search for the failures. When searching for the failure the adjacent components must generally be considered. If used other than intended the coupling can become a source of ignition. EU directive 2014/34/EU requires special care by the manufacturer and the user. General failures with use other than intended • Important data for the coupling selection are not forwarded. • The calculation of the shaft-hub-connection is not considered. • Coupling components with damage occurred during transport are assembled. • If the heated hubs are assembled, the permissible temperature is exceeded. • The clearance of the components to be assembled is not coordinated with one another. • Tightening torques have been fallen below/exceeded. • Components are mixed up by mistake/assembled incorrectly. • No original KTR components (purchased parts) are used. • Maintenance intervals are not observed. Breakdowns Different operating noise and/or vibrations occuring Repeated tearing of the magnetic forces Causes Hazard notes for potentially explosive atmospheres Elimination 1) Set the unit out of operation Increased temperature on 2) Eliminate the reason for the misalignment the surface of the (check the centering of the internal and the containment shroud and Misalignment external rotor in the containment shroud and the rotors. Increased re-align, if necessary) danger of ignition by hot 3) Check the wear and remove the magnetic surfaces. chippings completely, if required 1) Set the unit out of operation 2) Eliminate the reason for tearing (blocking of the pump by particles in the conveyed medium, damage on the bearing, too high Heating of the coupling starting torque of the engine, „docking“ of due to a lack of heat the internal or external rotor to the Tearing of magnetic dissipation, danger of containment shroud subject to bad forces ignition due to hot alignment see above surfaces 3) Re-synchronize the coupling components at standstill 4) Start the drive again 5) Please check for perfect operation Damaged external 1) Check the external rotor for damages on the magnets due to errors magnet in assembly (contact of 2) Replace the external rotor and assemble it the external rotor with carefully. Please make sure that there is a the containment radial direction to exclude contact with the shroud) containment shroud. Danger of ignition due to 1) Set the unit out of operation hot surfaces 2) Inspect operation parameters Operating parameters 3) If there is tearing during the starting do not meet with the process, reduce the starting torque and/or performance of the select a bigger coupling size (considering coupling the installation space), if necessary. 4) Assemble new coupling size, inspect alignment Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 6 46510 EN 17 of 22 10 Breakdowns, causes and elimination Breakdowns Repeated tearing of the magnetic forces Causes If the operating temperature is too high (magnet material: Sm2Co17 max 200 °C or NdFeB max. 150 °C), the magnetic field will be weakened Hazard notes for potentially explosive atmospheres Elimination Danger of ignition due to hot surfaces 1) Inspect the operation of the temperature feeler and the switch-off temperature 2) Inspect the coupling torque 3) Please replace the internal and external rotor if the torque is insufficient 4) If required, optimize the compulsory cooling flow of the internal rotor and optimise the material of the containment shroud (e. g. Hastelloy®, titan, ceramics) 1) Inspect the internal rotor and the containment shroud for friction and replace them, if necessary 2) Drain and clean the inside of the containment shroud 3) Use suitable filters recreating the purity of the medium. Abrasive particles in the conveying medium blocking the pump ! 7 KTR-N Sheet: Edition: When operating with a worn/defective coupling component proper operation is not assured. Environment and disposal 7.1 Environment In the interest of the environment our products comply with directive EC 1907/2006 (REACH). Any substances specified in the REACH SVHC list in an impermissible concentration are not used. 7.2 Disposal In respect of environmental protection we would ask you to dispose of the packaging or products on termination of their service life in accordance with the legal regulations and standards that apply, respectively. All coupling components consist of metal. Any metal components have to be cleaned and disposed of by scrap metal. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 8 KTR-N Sheet: Edition: 46510 EN 18 of 22 10 Maintenance and service MINEX®-S is a low-maintenance coupling. We recommend to perform a visual inspection on the coupling at least once a year. Please pay special attention to the condition of the components in the tight air gap between the magnet rotors and the containment shroud. • Since the flexible machine bearings of the driving and driven side settle during the course of load, inspect the alignment of the coupling and re-align the coupling, if necessary. • The coupling components have to be inspected for damages. • The screw connections have to be inspected visually. Having started up the coupling the tightening torques of the screws have to be inspected during the usual inspection intervals. ! With the use in potentially explosive atmospheres observe chapter 10.2 "Inspection intervals for couplings in potentially explosive atmospheres". 9 Spares inventory, customer service addresses We recommend to store major spare parts on site to ensure the readiness for use of the machine in case if a coupling fails. Contact addresses of the KTR partners for spare parts and orders can be obtained from the KTR homepage at www.ktr.com. KTR does not assume any liability or warranty for the use of spare parts and accessories which are not provided by KTR and for the damages which may incur as a result. Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 10 KTR-N Sheet: Edition: 46510 EN 19 of 22 10 Enclosure A Advice and instructions regarding the use in ! potentially explosive atmospheres Due to generation of heat when using metallic containment shrouds the following requirements for the use of the MINEX®-S must obligatorily be met: • In order to eliminate the generation of an inadmissible degree of heat, the temperature of the containment shroud must be monitored ensuring that the pump drive is switched off if the temperature is too high (see chapter 10.2). • Dry operation of the magnetic coupling is not permissible, i. e. immediately after assembly and start-up of the magnetic coupling the internal space of the containment shroud must be filled with the conveyed medium. • A compulsory cooling flow of the internal rotor by the conveyed medium or a sealing liquid must be provided for continuous dissipation of the heat generated in the air gap. 10.1 Intended use in potentially explosive atmospheres Conditions of operation in potentially explosive atmospheres MINEX®-S couplings are suitable for the use according to EU directive 2014/34/EU. 10.2 Inspection intervals for couplings in Equipment category potentially explosive atmospheres Inspection intervals If the MINEX®-S magnetic coupling is duly operated, maintenance is not required during all Please observe protection note ISO 16016. the complete operating time. An inspection of the coupling, the shaft bearings and the auxiliary seals should be made by suitable specialized staff within the scope of the revision of the unit, but at the latest after 2.5 years. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 10 KTR-N Sheet: Edition: 46510 EN 20 of 22 10 Enclosure A Advice and instructions regarding the use in 10.3 Temperature monitoring in potentially explosive atmospheres potentially explosive atmospheres The compulsory monitoring of heat generation in the coupling requires a suitable monitoring system with a respective temperature feeler. The system for temperature monitoring must be suitable for the respective potentially explosive atmosphere. The temperature feeler must be positioned between the containment shroud flange and the external rotor! ! • The assembly should be made in the coupling housing or in the bellhousing, dependent on the design. • The position should be as close as possible on the external rotor because that is where the highest temperature is. However, a minimum distance of 3 mm must be observed. Illustration 11: Position of the temperature feeler Dependent on the temperature class selected KTR stipulates the following switch-off temperatures for the temperature monitoring system: Table 7: Temperature class Max. permissible surface temperature in °C T1 T2 T3 T4 T5 T6 450 300 200 135 100 85 Switch-off temperature in °C Temperature measurement via resistance thermometers or via thermocouple (measurement in blind hole in containment shroud or on the sheath of containment shroud) Magnet material: Sm2Co17 Magnet material: NdFeB 200 150 200 150 185 150 120 120 85 85 70 70 Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Please observe protection note ISO 16016. Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 10 KTR-N Sheet: Edition: 46510 EN 21 of 22 10 Enclosure A Advice and instructions regarding the use in 10.4 potentially explosive atmospheres marking of coupling for potentially explosive atmospheres The ATEX marking of the MINEX®-S permanent magnetic coupling is made on a coupling component. For the complete marking refer to the operating/assembly instructions and/or the delivery note/package. The following marking applies for the products: • Magnet material: Sm2Co17 MINEX®-S <Year> II 2G Ex h IIC T6 -40 °C ≤ Ta ≤ +60 °C … T2 … +200 °C Gb KTR Systems GmbH, Carl-Zeiss-Straße 25, D-48432 Rheine • Magnet material: NdFeB MINEX®-S <Year> II 2G Ex h IIC T6 -40 °C ≤ Ta ≤ +60 °C … T3 … +150 °C Gb KTR Systems GmbH, Carl-Zeiss-Straße 25, D-48432 Rheine Short marking: (A short marking is only made if not possible differently for reason of space or functioning.) MINEX®-S <Year> Deviating marking applies until 31st October 2019: Complete marking: II 2G c IIC T X Substance group - gases: The marking with explosion group llC includes the explosion groups llA and llB. If the symbol was punched in addition to marking , the coupling component was supplied by KTR as an unbored or pilot bored version (see chapter 4.2 of the present operating/assembly instructions). Please observe protection note ISO 16016. Drawn: Verified: 2020-08-24 Pz/Wb 2020-09-01 Pz Replacing: Replaced by: KTR-N dated 2019-10-11 MINEX®-S with containment shroud made of stainless steel or Hastelloy® Operating/Assembly instructions 10 KTR-N Sheet: Edition: 46510 EN 22 of 22 10 Enclosure A Advice and instructions regarding the use in potentially explosive atmospheres 10.5 Certificate of conformity Certificate of conformity corresponding to EU directive 2014/34/EU dated 26 February 2014 and to the legal regulations The manufacturer - KTR Systems GmbH, D-48432 Rheine - states that the MINEX®-S Magnetic coupling in an explosion-proof design described in these assembly instructions are components corresponding to article 2, 3. of directive 2014/34/EU and comply with the general safety and health requirements according to enclosure II of directive 2014/34/EU. This declaration of conformity is issued under the sole responsibility of the manufacturers KTR Systems GmbH. The coupling described in here complies with the specifications of the following standards/rules: DIN EN ISO 80079-36:2016-12 DIN EN ISO 80079-37:2016-12 DIN EN ISO 80079-38:2017-10 IEC/TS 60079-32-1:2020-01-24 The MINEX®-S is in accordance with the specifications of directive 2014/34/EU. According to article 13 (3) of directive 2014/34/EU the technical documentation is deposited with the notified body (type examination certificate IBExU04ATEXB023 X): IBExU Institut für Sicherheitstechnik GmbH Fuchsmühlenweg 7 09599 Freiberg Rheine, 2020-08-24 Date Please observe protection note ISO 16016. Drawn: Verified: i. V. Reinhard Wibbeling Engineering/R&D 2020-08-24 Pz/Wb 2020-09-01 Pz i. A. Marco Vorholt Product Manager Replacing: Replaced by: KTR-N dated 2019-10-11 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Torque transmission without contact
- Magnetic coupling
- Containment Shroud
- Stainless Steel or Hastelloy® material
- High pressure and temperature resistance
- Potentially Explosive Atmospheres
- EC Machinery Directive compliant
Frequently asked questions
The maximum operating temperature is 300°C for magnets made of Sm2Co17 and 150°C for magnets made of NdFeB. This information is valid for containment shrouds made of Hastelloy®.
The containment shroud is assembled by pushing it over the internal rotor and screwing it to the adapter flange using cap screws. Make sure to tighten the cap screws evenly crosswise gradually in several revolutions to the specified tightening torque.
The displacement figures provided in the table are maximum values that must not be exceeded. The figures consider factors like thermal expansion or foundation settling and ensure safe operation of the coupling. For applications in potentially explosive atmospheres (explosion group IIC), only half of the displacement figures are permissible.