XPR B100-SA Owner's Manual
xpr B100-SA is a standalone biometric reader designed for easy management of users and configuration. It features advanced capacitive sensing technology for enhanced security and reliability. The device can store up to 100 fingerprint templates, including user, administrator, and installer profiles. It also offers adjustable relay timings and programming options for customized access control.
PDF
Download
Document
Advertisement
Advertisement
B100-SA v2 EN Standalone Biometric Reader INSTALLER’S MANUAL www.xprgroup.com Rev. 1.01 - 31.03.2022 1 CONTENTS 3 3 4 4 4 4 5 5 1. INTRODUCTION 2. MOUNTING 3. SPECIFICATIONS 4. APPLICATION DIAGRAM 5. RECOMMENDED SWIPING TECHNIQUE 6. INDICATION 7. WIRING 8. ADDING ADMIN FINGER 9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT Pairing B100-SA v2 with DINRTT Pairing B100-SA v2 with RTT Pairing B100-SA v2 with RU2 6 6 6 6 7 7 7 7 7 8 8 8 9 10. ADMINISTRATOR PROGRAMMING ADD finger relay 1 ADD finger relay 2 ADD finger relay 1&2 DELETE finger DELETE ALL fingers CHANGE ADMIN finger CHANGE INSTALLER finger Administrator programming block diagram 10 10 10 10 10 11 11. INSTALLER PROGRAMMING Set relay 1 time Set relay 2 time BUZZER ON/OFF BACKLIGHT ON/OFF Installer programming block diagram www.xprgroup.com 2 1. INTRODUCTION B100-SA v2 is access control fingerprint reader designed for easy management of the users and configuration. The scanner is made with advanced capacitive sensing technology that provides some advantages over optical solutions like: - making almost impossible to make fake copy of the users fingers - same performance in the different light conditions - good reading of fingers with stains from daily jobs Built in strong scanning and matching algorithm provides excellent tolerance in the way finger is swiped over the sensor reducing to minimum the need to repeat finger swiping at the sensor. The reader can store up to 100 finger templates. One template is reserved for User manager (Administrator), one template is reserved for Reader configuration (Installer) and up to 98 templates are for Users. RECOMMENDATIONS Consult with installer about safety level of the installation. There are devices with relays compatible with this reader that can increase the security of the system if needed. One or two enrolled fingers are enough for one user. Ask the installer before he leaves the site to enroll your finger as administrator. NOTES The Reader is using physical roughness of the fingerprint to scan the finger. Some of the users may have very flat fingertips, making difficult for the sensor to recognize correctly the fingerprint. In most cases, these are children and older persons. To solve this problem, do the following: 1. Try with different user’s fingers to find the “best” finger. 2. Check with the installer other models of the reader with added card reader or keypad for other type of access. MAINTENANCE No special or periodic maintenance is required. If cleaning is needed, use soft wet cloth and wipe gently the dirt. Do not use chemicals and materials that can scratch the sensor. WARNING! Do not touch the sensor with other objects than finger. Do not pour or splash with water or other liquids. When painting or construction work is ongoing in the area around the reader, protect the reader sensor area from possible damages and paint. If reader is to be dismounted or relocated, call authorized installer for the job. Disposal of this product must be handled according to all national laws and regulations. 2. MOUNTING Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna. Do not place the device near or above heating equipments. If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel. Do not let children touch the device without supervision. Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can’t be entered. The operating temperature of the product is between 0ºC - + 50ºC. XPR™ cannot guarantee the functionality of the product if measures and advice before are not followed. www.xprgroup.com 3 3. SPECIFICATIONS Fingerprint Capacity: Output: Push Button Input: Panel Connection: Door Open Time: Entry Mode: Programming: Admin/Installer Fingers: Backlight ON/OFF: Buzzer ON/OFF: Firmware upgrade: Current Consumption: Power Supply: Indication: IP Factor: Operating Temperature: Operating Humidity: Dimensions(mm): 98 templates 1 x Relay (2 A /24V AC/DC) Yes Cable, 0.5 m Pulse (1 to 30 seconds) or Toggle (ON/OFF) Finger By swiping 1 Administrator and 1 Installer Finger Yes Yes via RS-485 converter and windows application 100 mA max. 9-14 V DC Tricolor Status LED IP54 (internal use only) 0°C to +50°C 5% to 95% RH without condensation 92 x 51 x 25 (metal); 92 x 51 x 27 (ABS) 4. APPLICATION DIAGRAM Unsecured Area 5. RECOMMENDED SWIPING TECHNIQUE Follow the below instructions for correct finger swiping. Starting from the first finger joint, place the selected finger on the swipe sensor and move it evenly towards oneself in one steady movement. Result: For a valid swipe: Tricolour Status LED turns green + OK Beep(short + long beep) For an invalid or misread swipe: Tricolour Status LED turns red + Error Beep ( 3 short beeps) 6. INDICATION www.xprgroup.com 4 7. WIRING 8. ADDING ADMIN FINGER 1.Push dip switch no.2 in position ON. 2.Reset the Power of the device. 3.Wait for One long + multiple short beeps 4.Put the dip switch in position OFF. (short beeps will stop) 5.Wait for about 15 seconds for the LED to blink in Orange. 6.Swipe the Master finger min.6 times. (Until Ok Beep) Warning: This procedure also deletes all the users and the installer finger. Warning: This procedure will unpair the connected relay unit (RTT, DINRTT or RU2) www.xprgroup.com 5 9. PAIRING - BIOMETRIC READER AND REMOTE RELAY UNIT If secure installation is needed, the reader can be connected to remote relay unit at secured area, which also can play the role of request-to-exit push button. Follow the instructions bellow to pair (couple) both devices or refer to the Remote Relay’s Manual. Pairing B100-SA v2 with DINRTT 1. Close the Jumper. DINRTT beeps continuously and the red led blinks. 2. Open the Jumper 3. Wait for Beep + OK Beep (short + short + long beep) After the OK beep, the coupling is done. Pairing B100-SA v2 with RTT 1. Put Dipswitch No.1 to position ON. RTT beeps continuously and the red led blinks. 2. Put Dipswitch No.1 to position OFF. 3. Wait for Beep + OK Beep (short + short + long beep) After the OK beep, the coupling is done. Pairing DINB100-SA with RU2 1. Put the Jumper to closed position. RU2 beeps continuously and the red led blinks. 2. Put the Jumper to open position. 3. Wait for Beep + OK Beep (short + short + long beep) After the OK beep, the coupling is done. Warning: Changing the ADMIN finger will also unpair the remote relay unit. www.xprgroup.com 6 10. ADMINISTRATOR PROGRAMMING Use point fingers as Administrator and Installer. You can use the other fingers as access fingers. Administrator finger is enrolled at the end of the system installation. Initial enrollment of the Admin finger is described in installer manual. ADD Finger Relay 1 (Finger that will activate relay 1) Action Swipe Admin Finger 1 time Finger x1 Backlight Buzzer Sound slow blinking short beep Wait 5 seconds (until fast blinking) Swipe User Finger min. 6 times (until short + long beep) short beep x6 fast blinking short + long beep ADD Finger Relay 2 (Finger that will activate relay 2) Action Swipe Admin Finger 2 times Finger x2 Backlight Buzzer Sound slow blinking short beep Wait 5 seconds (until fast blinking) Swipe User Finger min. 6 times (until short + long beep) short beep x6 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays (DINRTT and RU2). Consult the installer if Relay 2 is available in your system. ADD Finger Relay 1&2 (Finger that will activate relay 1&2) Action Swipe Admin Finger 3 times Finger x3 Backlight Buzzer Sound slow blinking short beep Wait 5 seconds (until fast blinking) Swipe User Finger min. 6 times (until short + long beep) short beep x6 fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays (DINRTT and RU2). Consult the installer if Relay 2 is available in your system. DELETE Finger Action Swipe Admin Finger 4 times Finger x4 Backlight Buzzer Sound slow blinking short beep Wait 5 seconds (until fast blinking) Swipe User Finger short beep x1 fast blinking www.xprgroup.com short + long beep 7 DELETE ALL Fingers Action Swipe Admin Finger 4 times Finger x4 Wait 5 seconds (until fast blinking) Swipe Admin Finger 2 times x2 Backlight Buzzer Sound slow blinking short beep slow blinking short beep fast blinking multiple beeps Backlight Buzzer Sound slow blinking short beep slow blinking short beep fast blinking short + long beep CHANGE ADMIN Finger Action Swipe Admin Finger 5 times Finger x5 Wait 5 seconds (until fast blinking) Swipe NEW Admin Finger min.6 times x6 CHANGE/Enroll INSTALLER Finger Action Swipe Admin Finger 6 times Finger x6 Wait 5 seconds (until fast blinking) Swipe NEW Installer Finger min.6 times x6 Backlight Buzzer Sound slow blinking short beep slow blinking short + long beep fast blinking 3 short beeps Administrator Programming block diagram Swipe the ADMIN Finger 1 to 6 times depending of the desired menu www.xprgroup.com 8 11. INSTALLER PROGRAMMING Set Relay 1 Time (on board) Action Swipe Installer Finger 1 time Finger x1 Backlight Buzzer Sound slow blinking short beep Wait 5 seconds (until fast blinking) Swipe the INSTALLER Finger and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode short beep x1 x1 fast blinking beeps on 1 second fast blinking short + long beep Backlight Buzzer Sound slow blinking short beep Set Relay 2 Time (remote) Action Swipe Installer Finger 2 times Finger x2 Wait 5 seconds (until fast blinking) Swipe the INSTALLER Finger and start counting seconds Swipe the INSTALLER Finger to stop or wait 30 seconds to put the relay in toggle mode short beep x1 x1 fast blinking beeps on 1 second fast blinking short + long beep Relay 2 is available if the reader is used with remote relay unit with 2 relays (DINRTT and RU2). Consult the installer if Relay 2 is available in your system. BUZZER ON/OFF Action Swipe Installer Finger 3 times Finger x3 Backlight Buzzer Sound slow blinking short beep Wait 5 seconds (until fast blinking) Swipe Installer Finger short beep x1 fast blinking short + long beep Backlight Buzzer Sound slow blinking short beep BACKLIGHT ON/OFF Action Swipe Installer Finger 4 times Finger x4 Wait 5 seconds (until fast blinking) Swipe Installer Finger short beep x1 fast blinking www.xprgroup.com short + long beep 9 Installer Programming block diagram Swipe the Installer Finger 1 to 4 times depending of the desired menu www.xprgroup.com 10 www.xprgroup.com 11 This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU. www.xprgroup.com 12 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Fingerprint access control
- Standalone operation
- Capacitive sensing technology
- Up to 100 user templates
- Administrator and Installer profiles
- Adjustable relay timings
- Programming options
Frequently asked questions
To add a new user, you need to first swipe the Administrator finger, then wait for the backlight to blink fast, and then swipe the user's finger at least 6 times until you hear a short and long beep.
The Administrator finger is used to manage user access and perform administrative tasks. The Installer finger is used to configure the reader settings, such as relay timings and buzzer settings.
Yes, you can pair the B100-SA reader with different remote relay units such as DINRTT, RTT and RU2. Refer to the Remote Relay's Manual for specific pairing instructions.