B100P-BT-EH-SA
EN
Bluetooth® standalone biometric reader with integrated RFID reader
USER’S MANUAL
1. SPECIFICATIONS
User capacity:
Relays:
Output:
Entry mode:
Proximity reading type:
Reading distance:
Power supply:
Buzzer, backlight control:
Tamper:
RS-485 interface:
Door Open Time:
IP Factor:
Operating Temperature:
Operating humidity:
Firmware upgrade:
Wiegand output:
Programming:
Door operation:
Holidays:
Event capacity:
100 fingerprints and 100 Cards
1 or 2 depending on the remote relay unit
1 withRTT and RU1 and 2 with RU2 and DINRTT
RS-485, Wiegand
Fingerprint, Card, Fingerprint or Card
EM 4002/4100 and HID (125kHz)
Up to 4cm
12 VDC; max. 100mA
Yes, ON/OFF via XPR Smart Admin
Yes
Yes, for connecting I/O boards like
RU1, RTT, RU2, DINRTT
0 to 255 sec. or toggle (ON/OFF mode)
IP54 (internal use only)
0ºC to 50ºC
5% to 95% RH without condensation
Yes, via Bluetooth® wireless technology
Wiegand 24, 26, 32, 34, 56, 58 bits
Via XPR Smart Admin
Via XPR Smart Access
24
4000
Important note:
The Bluetooth® reader comes with RU1 remote relay unit.
Make sure to make firmware update with the latest available firmware.
2. MOUNTING
Rubber gasket
Front
Mounting base (optional)
Back
Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna.
Do not place the device near or above heating equipments.
If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can’t be entered.
The operating temperature of the product is between 0ºC - + 50ºC. XPR™ cannot guarantee the functionality of the product if measures and advice before
are not followed.
3. RESET READER TO DEFAULT
1. Turn the device OFF
2. Put dipswitch 1 to position ON
3. Turn the power ON
4. Wait approx. 15 seconds until continuos beeps.
5. Put dipswitch 1 to OFF
6. Wait for long beep.
The reset procedure will bring the reader to default. The
password will be deleted, all the users and the reader will be
unpaired from the remote relay unit.
Unpairing the reader after reset, prevents unauthorized
reset and keeps the unit in high security state.
www.xprgroup.com
Rev. 1.05 - 11.04.2022
1
4. WIRING AND PAIRING
There are four options to wire and pair the reader. It can be paired to a remote relay unit (RU2, RU1, DINRTT and RTT).
)
RU2
2 Relay Remote Unit
DINRTT
2 Relay Remote Unit and
request-to-exit Button
m
50
m
5(
48
RS
.
ax
The Bluetooth reader must be connected to
remote relay unit, unless is used as wiegand
reader.
The remote relay units compatible with B100P-BTEH-SA are RU1, RU2, RTT and DINRTT. Once
connected, the remote relay unit must be paired
with the Bluetooth reader.
B100P-BT-EH-SA
Bluetooth biometric reader
with integrated proximity reader
Pairing the reader with remote relay unit is done
from the remote relay unit and enables added
security. After being paired, it is not possible to
switch any of the devices, since the reader will
work only with the paired remote relay unit.
RU1
1 Relay Remote Unit
RTT
1 Relay Remote Unit and
request-to-exit Button
Secured Area
Unsecured Area
4.1 Wiring and pairing B100P-BT-EH-SA + RU1
Pairing Reader with RU1 (high security)
- Keep the button pressed
for at least 5 sec. and the
units will be paired.
Other pairing devices:
Device
Description
Relays
RU2
DIN rail mount remote relay unit
2
DINRTT
Flush mount sensitive push button and remote relay
2
RTT
Surface mount sensitive push button and remote relay
1
4.2 Wiring B100P-BT-EH-SA to Wiegand Controller
By default, the reader is set to Wiegand
26 bit.
You can set the reader, using the
software, to Wiegand 24, 26, 32, 34, 56,
58 bits.
www.xprgroup.com
2
5. SETTING UP READERS WITH XPR SMART ADMIN WINDOWS SOFTWARE
1. Add site first.
2. Click on “ADD” reader.
3. Select type “B100P-BT-EH-SA”.
4. Scan for readers near by by clicking on “Scan”. Found readers will be listed (pic.2). Click on “Select”.
5. Add a pairing key between the PC and the Bluetooth reader and a password. (pic. 3)
6. If the pairing is successful, the buttons in the reader section will be enabled.(pic.4)
You can download 2 softwares for Windows: XPR Smart Access and XPR Smart Admin from our website:
Users Software
Administrator Software
Software for the installation
administrator, allowing him/her to
program all readers and update
them, manage users and their
access rights, download events
and edit reports. (distance: max. 5m).
Application for users,
allowing them to manage
the doors from a distance.
(distance: max. 5m).
6. ADDING USERS
1. Go to Users and select the user. Edit the name directly. Enable it.
2. Put a PIN Code and Card ID. The Card ID can be read directly from
the reader or from USB desktop reader.
3. Select proper Access level and validity period.
4. Go to “Biometry” tab and enroll fingerprints by swiping min. 6
times each finger.
5. After this, go to the reader and “Upload users to reader”.
The 2 smartphone apps are available in:
Users App
Administrator App
Application for users, allowing them
to manage the doors from a
distance.
(distance: max. 5m).
Application for the installation administrator,
allowing him/her to program one reader at a
time and update it, manage users and their
access rights, download events and edit
reports. (distance: max. 5m).
This product herewith complies with requirements of EMC directive 2014/30/EU, Radio Equipment Directive 2014/53/EU.
In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU.
www.xprgroup.com
3
">
