XPR BIOPROX-EM Owner's Manual

BIOPROX-EM
EN
Biometric Proximity Reader
INSTALLER MANUAL
1
CONTENTS
1. DESCRIPTION
3
2. SPECIFICATIONS
3
3. MOUNTING
4
4. WIRING
5
5. CONNECTING BIOMETRIC READERS TO EWS CONTROLLER
5
6
6
5.1 CONNECTING BIOMETRIC READERS IN SAME RS485 LINE WITH THE EWS CONTROLLERS
5.2 CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION
6. CONNECTING BIOMETRIC READERS TO 3RD PARTY CONTROLLER
6.1 CONVERTERS PIN DESCRIPTION
7
7
7. ENROLLMENT
8
8. CONFIGURING THE BIOMETRIC READERS IN PROS SOFTWARE
8
8
9
10
11
12
12
13
13
13
13
14
14
14
8.1 ADDING BIOMETRIC READER
8.2 ENROLLING FINGERPRINTS FROM A READER
8.3 ENROLLING FINGERPRINTS FROM DESKTOP READER
8.4 DELETING FINGERPRINTS
8.5 UPLOADING THE FINGERPRINTS TO THE BIOMETRIC READERS
8.6 FIRMWARE UPDATE
8.7 ENTRY MODE
8.7.1 Card or Finger
8.7.2 Card and Finger
8.7.3 Finger Only
8.8 SENSOR CALIBRATION
8.9 SEND CONFIGURATION
8.10 ADVANCED SETTING
9. CONFIGURING THE BIOMETRIC READERS IN BIOMANAGER
9.12 CUSTOM WIEGAND
15
15
16
17
17
17
17
18
18
18
19
19
19
19
20
10. WIEGAND PROTOCOL DESCRIPTION
21
11. SAFETY PRECAUTIONS
22
12. TROUBLESHOOTING
22
9.1 ADD READER
9.2 EDIT READER
9.3 DELETE READER
9.4 CALIBRATE SENSOR
9.5 ADD USER
9.6 EDIT USER
9.7 DELETE USERS
9.8 ENROLL FINGERS
9.9 UPLOAD FINGERPRINTS TO READER
9.10 DELETE FINGERPRINTS
9.10.1 Deleting one user from the biometric reader
9.10.2 Deleting all users from the biometric reader
9.11 COMPLEX USER UPLOAD
2
DESCRIPTION
BIOPROX-EM is a Wiegand biometric and proximity reader for access control applications with programmable wiegand output. It
offers storage of up to 9500 fingerprints, it reads EM4100 compatible cards/tags and has a programmable Wiegand Output (8 to
128 bits).
The tamper switch output can trigger the alarm system, if an attempt is made to open or remove the unit from the wall.
SPECIFICATIONS
Fingerprint capacity
up to 9500 fingerprints
Technology
Biometry and Proximity (125 KHz, EM)
Authentication
Finger, Card, Finger or/and Card
Fingerprints per user
1-10 fingerprints
Proximity reading type
EM 4002, EM 4100
Reading distance
2 to 5cm
Interface
Wiegand 8 to 128 bits; Default: Wiegand 26bit
Protocol programming
By PROS software (EWS system) and BIOMANAGER (all access control systems)
Cable distance
50m
Fingerprint Sensor Type
Capacitive
1:1000 identification time
970 msec, including feature extraction time
Fingerprint enrolment
On the reader or from the USB desktop reader (BIOE)
Panel Connection
Cable, 1m
Green and Red LED
Externally Controlled
Orange LED
Idle mode
Buzzer
Yes
Backlight ON/OFF
Yes, by software settings
Tamper
Yes
Consumption
Max. 120mA
IP Rating
65
Power supply
9-14V DC
Operating Temperature
-15°C to +50°C
Dimensions (mm)
100 x 94 x 30
Housing
Moulded Aluminium
Colour
Silver, Red, Green, Dark Grey, Blue, White
3
MOUNTING
Ø6.0
30mm
Cable
ATPD-MINI
100 mm
94 mm
30 mm
If the biometric reader is installed and used outdoor, the reader MUST be fitted with the ATPD-MINI polycarbonate cover available
in our accessories in order to protect the sensor from direct rainfall. The operating temperature of the product is between -15ºC - +
60ºC. If the reader is installed in an environment where the temperature can drop below -10ºC or/and if the sensor could only be
exposed to direct sunlight, it is strongly recommended to install the reader inside a third party sealed wall mount box (fitted with
additional heater if very low temperature) to keep a constant sensor level performance. XPR™ cannot guarantee the functionality
of the product if measures and advice before are not followed.
It is also strongly recommended to use double technology biometric readers when use outdoor to offer first higher security but also
the possibility to use different readers depending on users.
4
WIRING
12V DC
Red
Black
Pink
Violet
Orange
Green
White
Yellow
Gray
Blue
GND
A
B
RS485
LED Red LED Green -
LRLGD0
D1
WIEGAND
Tamper
Tamper
12V DC
GND
A
B
LRLGD1
D0
Tamper
Tamper
Tricolor LED (Red, Green, Orange)
9-14V DC
ground
RS485 A
RS485 B
Red LED Green LED Data 1
Data 0
Tamper Switch(NO)
Tamper Switch(NO)
CONNECTING BIOMETRIC READERS TO EWS CONTROLLER
- The Biometric readers can be connected to virtually any controller that conforms to Wiegand format standards (standard Wiegand
26bit or self-defined Wiegand).
- The lines D0 and D1 are the Wiegand lines and the Wiegand Number is sent through them.
- The RS485 line (A, B) is used for fingerprint transfer and reader settings.
- The Biometric readers must be powered from the controller.
- If you use different power supply for the biometric reader, connect the GND from the both devices to ensure correct transfer of
the wiegand signal
- When you have connected the reader and powered on, the LED should flash in orange light + 2 beeps. This lets you know it's on
and ready for use.
- Fingerprint enrollment is done from the PC Software. Connection between the Biometric readers and the PC must be established.
A
A
ZD2
NO1 COM NC1 NO2 COM NC2
Door 1
RE2
Door 2
RE3
NO3 COM NC3 NO4 COM NC4
RE4
J1
RE1
ICN2
Free Out 1 Free Out 2
A
A
LD9
LD8 R35
A
D3
L2
C28
IC7
D1
D0
12V out
GND
LD13
A
C29
C27
Free Led 2
IC8
L6
ZD1
R1
R13
R2
FUSE1
LD6 R33
IC3
R16
C6
C1
C32
R45
C18
R25
RoHS
R34 R38
IC5
R53
R15
R24R49
18
R
22
D2
C16
LD15
R
C12
L5
Free
R47 Led 1A
LD20
C43
R19
L8
ZD4
R3
R14
R4
ZD3
L9
ICN1
C13
R20
R36
RX3
RX4
U5
R48
D5
C45
R37
D1
D0
12V out
GND
C33 Free R55
Led 2 LD16
GND A
LD14
Free R46
Led A1
U4
R9
IC6
ZD5
ZD6
R10
A
A
GND
Door Sensor2
L11
L10
Door Sensor1
TCP/IP
C34
C3
Exit Button2 L3
C15
C44
Ser No: 11-04-16-013
Mac: 00-04-A3-16-90-D
R11
C2
GND
D10
X1
X3
C5
R17
3 3 6 1 1 1 0 1 3 1
Exit Button1
U1
LD21
PB1 gnd PB2 DS1 gnd DS2
R50
R54
R21
IN1 IN2 IN2
12V IN1
+ - + -
50m. max
IC1
C42
IC11
L4
C41
BAT
12Vdc Out
R7
Free In 1 IC15
+
IC12
Free In 1 IC2 In 2 +
Free
Free In 2TAS1
R6
R23
R28
System
OK
IC1
FUSE2
Rb6
LD23
Busy
Tx
Rx
R62
LD22
A
LD18
LD19
R5
C4
A
LD17
LD5 R32
A
A
D13
C40
H1
Earth
L7
Earth
screw
Fuse
A B gnd
led1 led2 gnd 12V D0 D1
led1 led2 gnd 12V D0 D1
gnd12V
pink
A
B
violet
green
LGorange LRblack GND
red
+12V
white
D0
yellow
D1
5
CONNECTING BIOMETRIC READERS IN SAME RS485 LINE WITH THE EWS CONTROLLERS
Jumper for
RS485 termination
TCP/IP
Jumper for
RS485 termination
1 km max / 32 Units (EWS + Biometric Readers)
gnd
gnd
RS485
Stub
max. 5m
50 ohm
50 ohm
 The Biometric readers are connected through RS485 bus. The same RS485 bus that the EWS controllers are connected to.
 Maximum units in one network (EWS + Biometric readers) is 32.
 If there are more than 32 units in one network, please utilize RS 485 HUB to connect.
 The RS485 Line should be configured in the form of a daisy chain, NOT in a form of a star. If star must be used in some points, keep
the stubs from the RS485 backbone as short as possible. Maximum length of the stub is dependant of the installation (total
number of devices in RS485 line (total cable length, termination, cable type...) so recommendation is to keep stubs shorter than
5 meters, keeping in mind that this can be possible reason for errors in communication with PC software
 The cable must be twisted and shielded with a min. 0.2 mm2 cross section.
 Connect the ground (0V) of each unit in the RS 485 Line using a third wire in the same cable.
 The shield of the communication cable between two devices must be connected to the EARTH from ONE side of the RS 485 Line.
Use the side that has earth connection to the building’s grounding network.
CONNECTING BIOMETRIC READERS WHEN ALL THE CONTROLLERS HAVE TCP/IP COMMUNICATION
TCP/IP
Switch
50m
max.
50m
max.
50m
max.
 When all the controllers are connected via TCP/IP, then the RS485 network becomes local (from Reader 1 to the Controller then to
the Reader 2).
 Connect the readers directly to the Rs485 terminals in each controller.
 If the distance Reader-Controller is high (50meters) and if the communication with the reader can not be established, then
terminate the RS485 network by closing the jumper in the EWS Controller or as described in chapter 4.
6
CONNECTING BIOMETRIC READERS TO THIRD PARTY CONTROLLERS
3rd party controller
- + D0 D1
3rd party controller
- + D0 D1
- + D0 D1
- + D0 D1
BIOE
CNV100
RS485 A
A
RS485 B
B
USB Desktop Reader
CNV200
optional
BIOMANAGER Software
CNV300
 Connect the lines D0, D1, Gnd and +12V to the third party controller.
 Connect the RS485 Line (A, B) to the converter. Connect the converter in the PC.
 Fingerprint enrollment is done from the PC Software. Connection between the Biometric readers and the PC must be established.
 The Biometric readers communicate with each other with a RS485 and with the PC Software through a Converter.
 The RS485 Line should be configured in the form of a daisy chain, NOT in a form of a star. Keep the stubs from the RS485 backbone
as short as possible (not more than 5 meters)
 Only one converter per installation is needed, not per reader.
CONVERTERS PIN DESCRIPTION
PIN 1
PIN 1
PIN 1
CNV100
CNV200
CNV300
Converter RS485 to RS232
Does not requires installation
Converter RS485 to USB
Requires installation as USB serial
device (refer to CNV200 Manual). The
Drivers are located on the CD.
Converter RS485 to TCP/IP
Does not require installation. IP
address set through Internet
Browser(refer to CNV300 Manual)
Biometric Reader
Converter
RS 485 A
PIN 1 (RS 485 +)
RS 485 B
PIN 2 (RS 485 -)
7
ENROLLMENT
CONFIGURING THE BIOMETRIC READERS IN PROS CS SOFTWARE
ADDING BIOMETRIC READER
1. Expand the Door item to view the readers
2. Right click on the reader and select properties (8.1)
3. In the Basic tab, for “Type” of the Reader select “BIOPROX-EM”. (8.2)
4. After selecting the type, a third tab will appear “Biometric”. Go to that tab and put the serial number of the Biometric
Reader. (8.3)
Important Note: The serial number of the reader can be found on a sticker inside the reader, on the packaging box and it can
be search from the software (right click on the portal/search devices/readers). (8.4 & 8.5)
To check if the reader is On Line, right click on the reader and select “Check version”. In the Event Window a message should
appear “Device ON Line, Type: BIOPROX-EM” (8.6)
BIOPROX-EM
BIOC3
8.1
8.5
8.3
8.2
8.4
8.6
8
ENROLLING FINGERPRINTS FROM A READER
1. Open the Users Window and create a new user.
Click on “New User”, put a name, ID(card number). (8.7)
2. Go to the “Biometric” Tab
3. Select the reader(with left click) from which the enrollment will be done. (8.8)
4. Right click on the fingertip and select enroll. (8.9)
5. In the next 25 sec. present the finger on the selected reader and the finger tip will turn red, with the percentage of
successful enrollment shown next to the fingertip. (8.10)
In these 25 sec. the reader will continuously blink in orange.
6. Repeat point 4&5 for each finger that should be enrolled.
7. Click on “Save New” and the fingerprint will be sent automatically to all Biometric Readers where that user has access, i.e. to
all the readers according to the Access Level assign to that user.
Example:
If the user has “Unlimited” Access level then the fingerprints will be sent to all readers, if the user has Access level only for
Reader1 and Reader 3 then the fingerprints will be sent only to those two readers.
Note:
To check if all the fingerprints are sent to the reader, right click on the reader and select “Memory Status”. (8.11)
In the event window a line will appear indicating the number of fingerprints stored in the reader. (8.12)
Note:
If more fingerprints are added for one user, all fingerprints will send the same Wiegand Code to the controller, the one written
in the field User ID(card Number).
8.8
8.7
8.9
8.11
8.12
8.10
9
ENROLLING FINGERPRINTS FROM DESKTOP READER
Plug the Desktop Reader (BIOE) in the PC. If the device is not installed automatically use the drivers located on the CD provided
with the Biometric reader. It is installed in the same way as a USB Device. When the desktop reader has been installed it will
automatically appear in the Software. (8.13)
1. Open the Users Window and create a new user.
Click on “New User”, put a name, ID(card number). ( 8.7)
2. Go to the “Biometric” Tab
3. Select the USB desktop Reader (with left click).
4. Place the finger on the BIOE, right click on the fingertip and select enroll. (8.9)
5. The finger tip will turn red, with the percentage of successful enrollment shown next to the fingertip. (8.10)
6. Repeat point 5 for each finger that should be enrolled.
7. Click on “Save New” and the fingerprint will be sent automatically to all Biometric Readers where that user has access, i.e. to all
the readers according to the Access Level assign to that user.
If the reader is off line, the fingers will be sent upon the connection is established between PROS server and the reader. No need for
additional enrollment or actions. The fingerprints will be sent as soon as communication is established.
Example:
If the user has “Unlimited” Access level then the fingerprints will be sent to all readers, if the user has Access level only for Reader1
and Reader 3 then the fingerprints will be sent only to those two readers.
Note:
To check if all the fingerprints are sent to the reader, right click on the reader and select “Memory Status”. (8.11)
In the event window a line will appear indicating the number of fingerprints stored in the reader. (8.12)
Note:
If more fingerprints are added for one user, all fingerprints will send the same Wiegand Code to the controller, the one written in
the field User ID(card Number).
8.7
8.13
8.9
8.11
8.10
8.12
10
DELETING FINGERPRINTS
In General, the fingerprints are stored in the Biometric reader and in the Software.
Deleting can be done only in the readers or from both places.
Deleting one user from the biometric reader
Select the User
Click on “Delete User”. The User together with its fingerprints will be deleted from both the software and the
fingerprint readers. (8.14)
Deleting all users from the biometric reader
Right click on the reader and select “Delete all users from reader” (8.15)
Delete one or more fingerprints
Select the User and open the “Biometric” tab
Go to the fingertip that needs to be deleted, right click and select ”Delete” for one finger or “Delete All” for all fingers
of the User.
Click “Save Changes”.
With this procedure the User's fingerprints are deleted from the software and from the reader. (8.16)
8.15
8.14
8.16
11
UPLOADING THE FINGERPRINTS TO THE BIOMETRIC READERS
Right click on the biometric reader
Select “Upload all users to reader”
While receiving the fingerprints the reader will blink in orange.
Note: Use this feature when you change or add a reader, if pending tasks are deleted in the software or if there are doubts that
fingerprints in the reader memory are not synchronized with the software database.
In normal usage, the fingerprints are sent automatically and this feature is not used.
8.17
FIRMWARE UPDATE
Right-click on the reader and select Firmware update menu (8.18)
On the Firmware update window, click on the Browse button (8.19). The default location of the firmware files installed with
PROS CS is in the folder "Firmware".
Select the firmware file with a "xhc" extension.
Click on the Upload button
Important: Wait for the update end message. Do not turn off the reader, the software or any communication device in
between during the entire process.
8.18
8.19
12
ENTRY MODE
8.7.1 Card or Finger
Right click on the biometric reader
Select “Properties” and go to the “Biometric” tab
For Entry Mode select “Card or Finger” (8.20)
Note: All the fingers and the card will send the same
wiegand number (8.21)
8.20
8.7.2 Card and Finger
Right click on the biometric reader
Select “Properties” and go to the “Biometric” tab
For Entry Mode select “Card and Finger” (8.21)
Use of the double security mode:
Present the card (ex. 88009016), in the next 8 sec. the
reader will blink in orange waiting for the finger.
Present the finger
8.21
8.7.3 Finger Only
Right click on the biometric reader
Select “Properties” and go to the “Biometric” tab
For Entry Mode select “Finger” (8.22)
Note:
In this mode the proximity reader will become inactive.
8.22
8.21
13
SENSOR CALIBRATION
Right click on the biometric reader and select
“Calibrate” and wait for confirmation message.
Note: It is recommended to do a calibration while
commissioning the reader and in cases when there are
problems with reading the fingers
SEND CONFIGURATION
· Right-click on the reader and select the Send
configuration menu
· See the events panel to check the configuration flow
Note: The biometric reader gets its settings
automatically. This function is used if the reader was off
line while making the changes.
ADVANCED SETTINGS
Send This ID for:
Unknown Finger sends the desired Wiegand when an
unknown finger is applied.
Sound level:
Sound level of the device (ON or OFF)
Finger Acceptance Flexibility:
Accepted tolerance. The recommended value is
“Automatic Secure”.
Sensitivity:
Bio-sensor sensitivity, the recommended value is 7,
most sensitive.
14
CONFIGURING THE BIOMETRIC READERS IN BIOMANAGER
BioManager is software for fingerprint management of XPR Biometric readers, when used with third party access controllers.
Main functions:
- Fingerprint Enrollment
It can be done by ANY Biometric reader in the network or by Desktop (USB) Biometric reader.
Note: The Desktop Biometric reader BIOE is only compatible to Biometric readers with capacitive sensor, not with the ones
with thermal sensor.
- Fingerprint Transfer
Finger templates can be sent to any Reader in the Network. Different Users can be sent to different Biometric readers.
- PIN Codes management and transfer
PIN Code length configuration (1 to 8 digits) and PIN Code transfer.
- Wiegand Output Configuration
The Wiegand output of the Biometric reader can be customized bitwise.
ADD READER
Right-click on the portal connected to the
reader and select Add reader
Click on Save and the reader icon appears
under the selected portal
Fill the Reader form
Right-click on reader and select Version info
15
If reader is online, new line is added on top of the event table
If reader is not online, following line is added on top of the event table
If reader is online, right click on reader and select Upload configuration
Check at event table if configuration was successful
EDIT READER
Right-click on the reader and select Properties
Edit reader properties and click Save button
Right click on the reader and select Upload configuration
Check at event table if configuration was successful
16
DELETE READER
Right-click on the reader and select Delete reader
CALIBRATE SENSOR
Right-click on the reader and select Calibrate
See the events panel to check the calibration flow
It is recommended to do sensor calibration once after reader is mounted. Clean the fingerprint sensor before calibration.
ADD USER
At user table, click on the last empty user field and enter user name
Click on ID (User code) field and enter ID number. This number will be sent by the reader to the access controller when user
finger is recognized by the reader
Click on PIN code field and enter the PIN. PIN code is used at readers with keypad. When PIN code is typed at reader, User ID
will be sent to the access controller
EDIT USER
 Find the user at user table to edit
 Click on the user field for edit (Name, ID or PIN)
 Type new value
 Press Enter on the keyboard
Important:
When ID is changed, warning message is displayed reminding that if ID exist in some reader, should be deleted from
reader prior to change.
17
DELETE USERS
 Check the users to be deleted
 Right-click on the users table
 Click on Delete checked users menu
Confirm warning message
ENROLL FINGERS
 Select the User in the User Column, not the check box (the check box is for sending
the fingerprints) and the User name cell will turn blue
 Select the Biometric reader or Desktop reader BIOE from where the enrollment
will be done
Right click on the fingertip and
select Enroll
Swipe the finger on the Reader and the finger tip will become blue, with
percentage of successful enrollment given right beside the fingertip
Note: If more fingerprints are added for one user, all fingerprints will send the same Wiegand Code to the controller.
UPLOAD FINGERPRINTS TO READER
Check the users which fingerprints will be sent to the Reader
Right-click on the Biometric reader those users should be sent and select Upload users
As each user is being sent, the checkbox will become unchecked indicating
that the user is successfully sent. In the same time the orange LED of the
Biometric reader blinks
Note: Average time for transferring one finger template is 0,6 sec.
Note: The PIN Codes are also being sent, if there are any.
18
DELETE FINGERPRINTS
After the transfer, the fingerprint are stored in the Biometric reader and in the PC.
Deleting can be done only in the software, only in the readers or from the both places.
9.10.1 Deleting one user from the biometric reader
Select the users checkbox.
Right click on the Reader and select Delete Users
The user is deleted from the reader, but his fingerprints are still in the software's database. They can be sent ones again without the
need of re enrollment.
9.10.2 Deleting all users from the biometric reader
Right click on the Reader and select Delete all
COMPLEX USER UPLOAD
Complex user upload is used to sent multiply user selection to more readers
Click on Upload table at main menu
19
Use mouse click to select the combination you need or use right-click to check or clear entire row or column
Select Upload Users to readers or Delete Users from readers at right-click menu
As upload is progressing, check boxes are cleared mining appropriate combination was successfully done
When upload is over, if there are still checked items, repeat the upload command
CUSTOM WIEGAND
BioManager has defined Wiegand 26 and 34 bit as standard options and other 3 Wiegand settings as user definable.
To setup custom Wiegand format
Select Wiegand menu from Settings
At Wiegand setup window select one from customs Wiegand
Set Wiegand parameter
Click on Save button
Note:
Wiegand settings are out of scope
for common end user. Please ask
your installer to set the parameters
and do not change it later.
For more information please refer to BioManager User Manual
20
WIEGAND PROTOCOL DESCRIPTION
The data is sent over the lines DATA 0 for the logic “0” and DATA 1 for the logic “1”. Both lines use inverted logic, meaning that a
pulse low on DATA 0 indicates a “0” and a pulse low on DATA 1 indicates a “1”.When the lines are high, no data is being sent. Only 1
of the 2 lines ( DATA 0 / DATA 1 ) can pulse at the same time.
Example: data 0010....
0
0
0
1
5V
D0
0V
1 ms
100 us
D1
5V
0V
Data bit 0 = approximately 100 us (microseconds)
Data bit 1 = approximately 100 us (microseconds)
Time between two data bits: approximately 1 ms (millisecond). Both data lines (D0 and D1) are high.
Description for the 26 bits Wiegand format
Each data block consists of a first parity bit P1, a fixed 8 bits header, 16 bits of user code and a 2nd parity bit P2. Such a data block
is shown bellow:
Parity bit (bit 1) + 8 bits header + 16 bits user code = 2 bytes
+
P1
XXXXXXXX
XXXXYYYY YYYYYYYY
Example:
170
31527
1
10101010
01111011 00100111
Parity bit (bit 26)
P2
0
Note: Parity bits are calculated as follows:
P1 = even parity calculated over the bits 2 to 13 (X)
P2 = odd parity calculated over the bits 14 to 25 (Y)
E A A A A A A A A B B B B B B B B B B B B B B B B O
Even
Parity
Bit
Site Code
User Code
Odd
Parity
Bit
21
SAFETY PRECAUTIONS
Do not install the device in a place subject to direct sun light without protective cover.
Do not install the device and cabling close to a source of strong electro-magnetic fields like radio-transmitting antenna.
Do not place the device near or above heating equipments.
If cleaning, do not spray or splash water or other cleaning liquids but wipe it out with smooth cloth or towel.
Do not let children touch the device without supervision.
Note that if the sensor is cleaned by detergent, benzene or thinner, the surface will be damaged and the fingerprint can't be
entered.
TROUBLESHOOTING
The Red Led on the Biometric Reader is blinking all the time
There were 15 unsuccessful attempts of authentication
(Finger or PIN). The Red LED will turn off after the first
accepted finger or PIN.
The keypad of the Biometric Reader is not working
The operation Mode of the Biometric Reader is set as
“Finger”. Please select “Keycode OR Finger” mode
Enrollment from desktop reader can be done, but the
Fingerprints are not sent to all Biometric Readers
in the network
·Check the Ser.No of the Readers.
·Check if proper termination is done as described before
Check if the Communication wires (A & B) are properly
connected to the reader
The Biometric Reader is not powered ON.
The tricolour LED is OFF.
Check the power Supply (red & black wire)
Fingerprint (or PIN Code) is recognized (the tricolor LED is
green), but the controller reports other ID number and the
access is denied
·If the user is not deleted from the reader and the same
user is enrolled again with new ID, the reader will
recognize the finger with the first ID. To resolve this,
delete all users from the reader and upload all users to the
reader
·Check the Wiegand Bus (yellow & white wire)
·Check if the ground of the controller and the Biometric
Reader is the same
Check if the length between Biometric Reader and the
controller is less than 50 m
Electro static discharge influences the Fingerprint
Scan.
Connect the housing of the Biometric Reader to the
earth wire
PIN Codes are working correctly, finger scan does not work.
The triocolour LED is OFF.
·Fingerprint Sensor malfunction
·Check the Sensor position and its physical condition
Reset the system. Contact your installer
Reader reading performance is decreased
·Check if fingerprint reading area is dirty. Do not clean the
device with any form of liquid. Use soft and dry cloth
only
Reading area is damaged. If the damage is minor, try to
calibrate the sensor
Fingerprint is not recognized normally
·Retry after drying the wetness of your finger
·When your finger is too dry, touch your forehead and try
again
When you have a cut on your registered finger, register
another fingerprint
22
This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with
RoHS directive EN50581:2012
23
">