XPR MTPADP-BT-EH-SA Owner's Manual

MTPADP-BT-EH-SA
EN
Bluetooth® standalone keypad with integrated RFID reader
USER’S MANUAL
1. SPECIFICATIONS
User capacity:
Relays:
Output:
Entry mode:
RFID reading type:
Reading distance:
PIN Code Length:
Power supply:
Buzzer, backlight control:
Tamper:
RS-485 interface:
Door Open Time:
IP Factor:
Operating Temperature:
Operating Humidity:
Firmware upgrade:
Wiegand output:
Programming:
Door operation:
Holidays:
Event capacity:
100 Cards and 100 PIN Codes
1 or 2 depending on the remote relay unit
1 with RTT and RU1 and 2 with RU2 and DINRTT
RS-485, Wiegand
PIN Code, Card, PIN Code or Card
EM 4002/4100 and HID (125kHz)
Up to 4cm
6 Digits
12 VDC; max. 100mA
Yes, ON/OFF via XPR Smart Admin
Yes
Yes, for connecting I/O boards like
RU1, RTT, RU2, DINRTT
0 to 255 sec. or toggle (ON/OFF mode)
IP65
-20ºC to +50ºC
5% to 95% RH without condensation
Yes, via Bluetooth® wireless technology
Wiegand 24, 26, 32, 34, 56, 58 bits
or 4, 6, 8 bit per key for the keypad
Via XPR Smart Admin
Via XPR Smart Access
24
4000
Important note:
The Bluetooth® reader comes with RU1 remote relay unit.
Make sure to make firmware update with the latest available firmware.
2. MOUNTING
Rubber gasket
Front
Mounting base (optional)
Back
Tricolor indication LED
3 (3 x 30mm)
1 (M3 x 8mm)
Access Granted
(Output 1 or 2)
Idle Mode
Access
Denied
3. RESET READER TO DEFAULT
1. Turn the device OFF
2. Put dipswitch 1 to position ON
3. Turn the power ON
4. Wait approx. 15 seconds until continuos beeps.
5. Put dipswitch 1 to OFF
6. Wait for long beep and orange back light led.
The reset procedure will bring the reader to default.
The password will be deleted, all the users and the reader will
be unpaired from the remote relay unit.
Unpairing the reader after reset, prevents unauthorized reset
and keeps the unit in high security state.
www.xprgroup.com
Rev. 1.03 - 13.04.2022
1
4. WIRING AND PAIRING
There are four options to wire and pair the reader. It can be paired to RU2, RU1, DINRTT and RTT.
)
RU2
2 Relay Remote Unit
DINRTT
2 Relay Remote Unit and
request-to-exit Button
m
50
m
5(
48
RS
.
ax
Pairing the reader with remote relay unit is done
from the remote relay unit and enables added
security. After being paired, it is not possible to
switch any of the devices, since the reader will work
only with the paired remote relay unit.
B100P-BT-EH-SA
Bluetooth biometric reader
with integrated proximity reader
The Bluetooth reader must be connected to remote
relay unit, unless is used as wiegand reader.
The remote relay units compatible with
MTPADB-BTEH- SA are RU1, RU2, RTT and DINRTT.
Once connected, the remote relay unit must be
paired with the Bluetooth reader.
RU1
1 Relay Remote Unit
RTT
1 Relay Remote Unit and
request-to-exit Button
Secured Area
Outside
4.1 Wiring and pairing B100P-BT-EH-SA + RU1
Pairing Reader with RU1 (high security)
- Keep the button pressed
for at least 5 sec. and the
units will be paired.
Other pairing devices:
Device
Description
Relays
RU2
DIN rail mount remote relay unit
2
DINRTT
Flush mount sensitive push button and remote relay
2
RTT
Surface mount sensitive push button and remote relay
1
4.2 Wiring B100P-BT-EH-SA to Wiegand Controller
By default, the reader is set to Wiegand
26 bit.
You can set the reader, using the
software, to Wiegand 24, 26, 32, 34, 56,
58 bits.
www.xprgroup.com
2
5. SETTING UP READERS WITH XPR SMART ADMIN WINDOWS SOFTWARE
1. Add site first.
2. Click on “ADD” reader.
3. Select type “B100P-BT-EH-SA”.
4. Scan for readers near by by clicking on “Scan”. Found readers will be listed (pic.2). Click on “Select”.
5. Add a pairing key between the PC and the Bluetooth reader and a password. (pic. 3)
6. If the pairing is successful, the buttons in the reader section will be enabled.(pic.4)
You can download 2 softwares for Windows: XPR Smart Access and XPR Smart Admin from our website:
Users Software
Administrator Software
Software for the installation
administrator, allowing him/her to
program all readers and update
them, manage users and their
access rights, download events
and edit reports. (distance: max. 5m).
Application for users,
allowing them to manage
the doors from a distance.
(distance: max. 5m).
6. ADDING USERS
1. Go to Users and select the user. Edit the name directly. Enable it.
2. Put a PIN Code and Card ID. The Card ID can be read directly from the reader or from USB
desktop reader.
3. Select proper Access level and validity period.
4. Go to “Biometry” tab and enroll fingerprints by swiping min. 6 times each finger.
5. After this, go to the reader and “Upload users to reader”.
The 2 smartphone apps are available in:
Users App
Administrator App
Application for users, allowing them
to manage the doors from a
distance.
(distance: max. 5m).
Application for the installation administrator,
allowing him/her to program one reader at a
time and update it, manage users and their
access rights, download events and edit
reports. (distance: max. 5m).
This product herewith complies with requirements of EMC directive 2014/30/EU, Radio Equipment Directive 2014/53/EU.
In addition it complies with RoHS2 directive EN50581:2012 and RoHS3 Directive 2015/863/EU.
www.xprgroup.com
3
">