XPR SC24000 Owner's Manual

xpr SC24000 is a standalone access control unit designed for two doors with features like programmable readers, 4000 user capacity, anti-passback option, and adjustable door relay time. It can be used for secure access control in various applications, including offices, buildings, and other facilities.

PDF

Document

SC24000
EN
2 Door standalone access control unit
CONTENTS:
1. Features
.................................................................................................. 1
2.Mounting
.................................................................................................. 2
3.Typical two door application .......................................................... ............. 2
4.Terminal block description
....................................................................... 3
5. DIP switch settings
.................................................................................... 3
6. Wiring
................................................................................................. 4
7. Factory reset
.................................................................................... 4
8. Programming
.................................................................................... 5
9. Anti Pass Back
.................................................................................... 7
10. Examples
................................................................................................. 8
11. Programming with Keypad (LCSP, VKP, INOX, MTPAD-M)
............. ... 8
12. Programming in double security mode (LCSP) ........................................... 9
1. FEATURES
Electrical Characteristics
Operating Voltage:
Current consumption :
Door Relays: Output Relays: 8 to 15V DC
max. 180 mA (without readers)
250 VAC/4A
250 VAC/4A
Environmental Characteristics
Operating Temperatures :
Operating Humidity : 0&ordm;C to +50&ordm;C
0 to 95% (non-condensing)
PCB Dimensions (mm) 102 L x 86 W
61 mm
• Programmable trough readers
• 4000 users (Cards)
• 2 reader inputs (Auto detect Wiegand26 / Wiegand34)
• 2 door relays (2 x 250VAC/4A)
• 2 door sensor inputs
• 2 push button inputs
• 2 Alarm relays: Output 1 (door forced alarm), Output 2
(door left open alarm)
• Programming done with Master1&amp;2, Delete, Reset APB,
Master 1 and Master 2 card
• Adjustable Door relay time (1 - 250sec, or ON/OFF(toggle)
mode)
• Anti Pass Back option
• Normal wiegand mode (card only) and LCSP mode (card and
PIN code) on any reader
• Shadow delete card - per user or per group of users
• Max. Users in 1 groups: 4000 (each group has 1 card)
• Single door mode / 2 readers (one reader on each side of the
door)
• 2 door mode / 2 readers (one reader on each door)
• 60 sec lockout after 15 invalid cards
• Enroll sequential block of cards - max. block of 100 cards
v.b2
107
mm
90
mm
www.xprgroup.com
1
2. MOUNTING
Rear view
On wall
74,35mm
m
,35m
74
On DIN Rail
3. TYPICAL TWO DOOR APPLICATION
www.xprgroup.com
2
4. TERMINAL BLOCK DESCRIPTION
Reader 1
Led Green Led Red GND
power supply
12 VDC
Data0
wiegand
Data1
Reader 2
Led Green Led Red GND
power supply
12 VDC
Data0
wiegand
Data1
12 VDC
GND
12 VDC
GND
led’s
NC
COM
NO
NC
COM
NO
led’s
(NC)
Door Sensors
Exit Buttons
(NO)
(NC)
(NO)
Power Supply
Door Sensor 1
GND
Push Button 1
Door Sensor 2
GND
Push Button 2
Door 1 Relay
Door 2 Relay
Alarm Outputs
NC
COM
NO
NC
COM
NO
Door Left Open Alarm
Forced Door Alarm
Output 1 (door left open alarm)
- ON if any door is left open by the time set in:
”Set door left open Alarm”
- OFF when door is closed
NOTE: If Door Sensors are not being used, the terminal
blocks Door Sensor1 and Door Sensor 2 should be
shorted with GND. By factory default, the controller will
be delivered with shorted Door sensors.
Output 2 (forced door alarm)
- ON if any door is open by force
- OFF when the door is closed
NOTE: Do not connect different Wiegand type of
readers. Both readers should be either Wiegand 26bit or
Wiegand 34bit.
5. DIP SWITCH SETTINGS
ON
1 2 3 4 5 6 7 8
1
2
3
4
5
6
7
8
ON
Double
Wiegand
on Reader 1
Double
Wiegand
on Reader 2
APB
follow
sensor ON
Anti Pass
Back option
ON
Enroll
Master Card
ON
Factory
Reset
ON
2 DOOR
Mode
Not used
OFF
Single
Wiegand
on Reader 1
Single
Wiegand
on Reader 2
APB
follow
sensor OFF
Anti Pass
Back option
OFF
Enroll
Master Card
OFF
Factory
Reset
OFF
1 DOOR
Mode
Not used
NOTE: Double wiegand is used for double security(Card + PIN Code). When LCSP-EM/MF is connected and LCSPEM/MF is set in double security mode, put the dipswitch 1 or 2 to position ON.
NOTE: If Door sensors are not used, dipswitch No.3 should stay OFF.
NOTE: In 1 Door Mode, both readers are assigned to Door1. User Card can be programmed to trigger both relays,
which gives the option the second door relay to be used as alarm.
www.xprgroup.com
3
6. WIRING
6.1 WIRING KEPADS LCSP, VKP, INOX, MTPAD-M
7. FACTORY RESET
1. Turn OFF the power Supply 2. Put DIP Switch 6 in position ON
3. Turn ON the power supply -
Green LED - ON, Red LED - blinking
4. Put DIP Switch 6 in position OFF
-
Green LED - OFF, Red LED - blinking and goes OFF
(wait for the Red LED to go OFF)
www.xprgroup.com
4
8. PROGRAMMING
IMPORTANT:
Connect Proximity Reader(Wiegand26 or Wiegand34) to READER 1 Input, including its free tension
LED’s.The Reader’s Free tension LED’s are used for visual indication during the programming process.
Insert Master cards
1. Turn OFF the power supply
2. Push the dip switch no.5 in position ON
3. Turn ON the power supply
Red LED - ON
4. On Reader1, present the master cards in this order: Master1&amp;2, Delete, Reset APB, Master1, Master2
Note: For the first inserted card, the green led will blink once, for the second, the green led will blink twice...etc
System can work without all master cards inserted (ex. Only Master, Delete and APB can be active).
Minimum master cards are two (Master1&amp;2 and Delete)
5. Put the dip switch in position OFF (SC24000 will return to operational mode)
Mark the master cards with the stickers provided in the kit
MASTER1&amp;2 Card
DELETE Card
217 40278
204 27141
Master1 Card
Reset APB Card
205 49142
224 33143
Master2 Card
101 00147
NOTE: Changing Master and Delete Card is done with the same procedure. Old Master/Delete Cards are deleted automatically.
Enroll a User
1. Present Master Card 2. Present Shadow Card 3. Present User Card - Green LED (or multiple User cards)
4. Present Master Card - Green LED
-
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - OFF
blinks twice on each user card
-
OFF, Red LED - OFF
Note: If the user is enrolled using MASTER1 card, the same user will have access only on DOOR1.
If the user is enrolled using MASTER2 card, the same user will have access only on DOOR2.
If the user is enrolled using Master1&amp;2 card, the same user will have access on DOOR1 and DOOR2.
NOTE: Shadow card can be issued for 1 user or for group of users. In both cases, write the name of the user on the shadow
card and keep all of the shadow cards on safe place.
NOTE: If more than one user is associated to same shadow card, deleting with that shadow card will result with deletion of all
the Users associated to that shadow card.
NOTE: If a shadow card needs to be changed, just enroll the same User with different Shadow card.
Shadow
Card 1
130 22346
Shadow
Card 2
130 22345
Shadow
Card 3
130 22344
User Card 1
User Card 1
130 22349
130 22349
User Card 2
130 22348
OR
Group
Shadow
Card 233 26735
User Card 2
130 22348
User Card 3
User Card 3
130 22347
130 22347
www.xprgroup.com
204 27142
5
Enroll Sequential Block of Cards
Note:
There is no sequence of numbering
Mifare cards.
Enroll a Block of 100 sequential cards assigned to Door1:
1. Present Master1 Card 2. Present Shadow Card 3. Present the beginning card of the block 3 times
4. Present the ending card of the block 3 times
5. Present Master1 Card -
Green LED- ON, Red LED - ON
Green LED - ON, Red LED - OFF
Green LED - blinks twice
Green LED - blinks twice
Green LED - OFF, Red LED - OFF
Note:
Before enrolling block of cards,
make sure that the numbers are in
sequence and that sequence is
smaller than 100.
Delete a User with its shadow card
1. Present Delete Card 2. Present Shadow Card -
Green LED - ON, Red LED - ON
Green LED-blinks twice, Red LED - ON
3. Present Delete Card -
Green LED - OFF, Red LED - OFF
(or multiple shadow cards)
Note: By deleting a shadow card, all the Users associated to that shadow card will be deleted.
Delete a User with user card
1. Present Delete Card 2. Present User Card -
Green LED - ON, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Delete Card -
Green LED - OFF, Red LED - OFF
(or multiple user cards)
Delete ALL Users
1. Present Delete Card 2. Present Master 1&amp;2 Card 3 times 3. Present Delete Card -
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - ON, Orange LED blinks once
Green LED - OFF, Red LED - OFF
Delete ALL Users assigned to DOOR1
1. Present Delete Card 2. Present Master 1 Card 3 times
3. Present Delete Card -
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - ON, Orange LED blinks once
Green LED - OFF, Red LED - OFF
Delete ALL Users assigned to DOOR2
1. Present Delete Card 2. Present Master 2 Card 3 times
3. Present Delete Card -
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - ON, Orange LED blinks once - Green
Green LED - OFF, Red LED - OFF
Reset All APB statuses
1. Present Reset APB card on any reader
www.xprgroup.com
6
Set Door1 Open Time
1. Present Master 1 Card 3 times 2. Present Delete Card -
Green LED - OFF, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Master 1 Card -
Green LED - OFF, Red LED - OFF
Present the card X times for X seconds
(Door open Time)
Set Door1 in Toggle (ON/OFF) Mode
1. Present Master 1 Card 3 times
2. Present Master 1 Card -
Green LED - OFF, Red LED - ON
Green LED - OFF, Red LED - OFF
1. Present Master 2 Card 3 times
2. Present Delete Card -
Green LED - OFF, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Master 2 Card -
Green LED - OFF, Red LED - OFF
Set Door2 Open Time
Present the card X times for X seconds
(Door open Time)
Set Door2 in Toggle (ON/OFF) Mode
1. Present Master 2 Card 3 times
2. Present Master 2 Card -
Green LED - OFF, Red LED - ON
Green LED - OFF, Red LED - OFF
Set door left open Alarm
To set 40 seconds for door left open time:
1. Present Master1&amp;2 Card 3 times 2. Present Delete Card 4 times (4 x 10 sec. = 40 sec.)
3. Present Master1&amp;2 Card To disable the alarm:
Present Master1&amp;2 Card 3 times Present Master1&amp;2 Card Green LED - OFF, Red LED - ON
Green LED - blinks twice, Red LED - ON
-
Green LED - OFF, Red LED - OFF
-
Red LED - ON
Red LED - OFF
9. ANTI PASS BACK
ON
1 2 3 4 5 6 7 8
DipSwitch No.4 - ON
To enable the Anti Pass Back option simply put the dipswitch no.4 to position ON.
If Door sensors are not being used at the installation, keep the dipswitch No.3 to position OFF. In this case, the APB
Status shall be determined by a card punch (was the card presented or not).
If Door sensors are used, then dipswitch. No3 should be in position ON. In this case, the APB status is determined by
the door status (was the door open or not).
www.xprgroup.com
7
10. EXAMPLES
Task1:
Make 1 Door installation with 1 Reader. Enroll 2 users to open the door.
DIP switch settings: all are OFF
1. Present Master1 Card
2. Present Shadow Card
3. Present User Card 1
4. Present User Card 2
4. Present Master1 Card
Task2:
Make 1 Door installation with IN and OUT Reader. Enroll User1 with access to Door1 in Anti Pass Back Mode and additional
User2 that will not have access to Door1, but will be able to turn the lights in the office ON/OFF.
DIP switch settings:
No.4-ON, all other are OFF
Relay connection:
Door relay1 - Door Lock; Door Relay 2 - Lights Main Switch
1. Present Master1 Card
2. Present Shadow Card 1
3. Present User Card 1
4. Present Master1 Card
1. Present Master2 Card
2. Present Shadow Card 2
3. Present User Card 2
4. Present Master2 Card
User1 with Access to Door1
User2 to be able to activate
Door Relay2 (Lights), but not
Door Relay 1.
1. Present Master 2 Card 3 times
2. Present Master 2 Card
Make Door relay 2 to work in ON/OFF Mode
Task3:
Make 2 Door installation. Enroll User 1 to open only DOOR1 and User 2 to open DOOR2 and User3 to open Door1 and Door2.
DIP switch settings:
7 - ON; all others OFF
Relay connection:
Door relay1 - Door Lock; Door Relay 2 - Door Lock
1. Present Master1 Card
2. Present Shadow Card 1
3. Present User Card 1
4. Present Master1 Card
1. Present Master2 Card
2. Present Shadow Card 2
3. Present User Card 2
4. Present Master2 Card
1. Present Master1&amp;2 Card
2. Present Shadow Card 3
3. Present User Card 3
4. Present Master1&amp;2 Card
User1 with Access to Door1
User2 with Access to Door2
User3 with Access to Door1 and Door2
11. PROGRAMMING WITH KEYPAD(LCSP, VKP, INOX,MTPAD-M)
The programming with Keypad is same as programming with proximity reader.
Please refer to programming explained on pages 4 to 7, just replace the word “Card” with “PIN Code”
Keypad settings
Set the keypad to be compatible with SC24000 Standalone Controller
Press B+000000 to enter the menu
Press 6
Press 1
Press A to exit the menu
This will set the Keypad in “Wiegand26 bit Normal”, “4 Digits PIN Code” and “Card or PIN Code” mode(LCSP).
For other settings (like changing PIN Code length), please refer to the keypad’s manual.
www.xprgroup.com
8
12. PROGRAMMING IN DOUBLE SECURITY MODE(LCSP)
Double Security Mode is possible only with double technology readers (proximity + keypad, LCSP)
1. If LCSP is connected to Reader1 Input put the dipswitch1 to position ON
If LCSP is connected to Reader2 Input put the dipswitch2 to position ON
2. Set the keypad to double security mode
Press B+000000 to enter the menu
P ress 6
Press 4
Press 5
Press 3
Press A to exit the menu
ON
1 2 3 4 5 6 7 8
This will set the Keypad in “Wiegand26 bit Double”, “4 Digits PIN Code” and “Card and PIN Code” mode.
Insert Master cards
1. Turn OFF the power supply
2. Push the dip switch no.5 in position ON
3. Turn ON the power supply - Red LED - ON
4. On Reader1, present the master cards in this order:
Master1&amp;2
+
ANY 4 digit Code
Delete +
ANY 4 digit Code
Reset APB
+
ANY 4 digit Code
Master1 +
ANY 4 digit Code
Master2
+
ANY 4 digit Code
Note: For the first inserted card, the green led will blink once, for the second, the green led will blink twice...etc
System can work without all master cards inserted (ex. Only Master, Delete and APB can be active).
Minimum master cards are two (Master1&amp;2 and Delete)
5. Put the dip switch in position OFF (SC24000 will return to operational mode)
Mark the master cards with the stickers provided in the kit
MASTER1&amp;2 Card
204 27141
DELETE Card
217 40278
Reset APB Card
205 49142
Master1 Card
224 33143
Master2 Card
101 00147
NOTE: Changing Master and Delete Card is done with the same procedure. Old Master/Delete Cards are deleted automatically.
www.xprgroup.com
9
Enroll a User
1. Present Master Card
2. Present Shadow Card
3. Present User Card
+
+
+
ANY 4 digit Code ANY 4 digit Code ANY 4 digit Code -
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - OFF
Green LED - blinks twice on each user card
4. Present Master Card
+
ANY 4 digit Code
-
Green LED - OFF, Red LED - OFF
(or multiple User cards + ANY 4 digit Code)
Note: If the user is enrolled using MASTER1 card, the same user will have access only on DOOR1.
If the user is enrolled using MASTER2 card, the same user will have access only on DOOR2.
If the user is enrolled using MASTER1&amp;2 card, the same user will have access on DOOR1 and DOOR2.
IMPORTANT:
With the procedure above, ONLY the Card is stored. To store the PIN Code, present the newly enrolled Card
(the Orange LED will start blinking) and type the desired PIN code.
In other words, after exiting the programming, the first time the card is punched, the first PIN Code typed
becomes the Pin Code assigned to that card only.
This feature can prevent the installer to know the PIN Code of the user. The user can choose his own PIN Code.
NOTE: Shadow card can be issued for 1 user or for group of users. In both cases, write the name of the user on the shadow
card and keep all of the shadow cards on safe place.
NOTE: If more than one user is associated to same shadow card, deleting with that shadow card will result with deletion of all
the Users associated to that shadow card.
NOTE: If a shadow card needs to be changed, just enroll the same User with different Shadow card.
Shadow
Card 1
User Card 1
User Card 1
130 22349
130 22349
130 22346
Shadow
Card 2
User Card 2
130 22345
Shadow
Card 3
130 22348
Group
Shadow
Card 233 26735
OR
User Card 2
130 22348
User Card 3
User Card 3
130 22347
130 22347
130 22344
204 27142
Delete a User with its shadow card
1. Present Delete Card + ANY 4 digit Code 2. Present Shadow Card + ANY 4 digit Code -
Green LED - ON, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Delete Card + ANY 4 digit Code -
Green LED - OFF, Red LED - OFF
(or multiple shadow cards)
Note: By deleting a shadow card, all the Users associated to that shadow card will be deleted.
Delete a User with user card
1. Present Delete Card + ANY 4 digit Code 2. Present User Card + ANY 4 digit Code -
Green LED - ON, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Delete Card + ANY 4 digit Code -
Green LED - OFF, Red LED - OFF
(or multiple user cards)
www.xprgroup.com
10
Delete ALL Users
1. Present Delete Card + ANY 4 digit Code 2. Present Master 1&amp;2 Card + ANY 4 digit Code 3 times
3. Present Delete Card + ANY 4 digit Code -
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - ON, Orange LED blinks once
Green LED - OFF, Red LED - OFF
-
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - ON, Orange LED blinks once
Green LED - OFF, Red LED - OFF
-
Green LED - ON, Red LED - ON
Green LED - ON, Red LED - ON, Orange LED blinks once
Green LED - OFF, Red LED - OFF
1. Present Master 1 Card + ANY 4 digit Code 3 times 2. Present Delete Card + ANY 4 digit Code -
Green LED - OFF, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Master 1 Card + ANY 4 digit Code -
Green LED - OFF, Red LED - OFF
-
Green LED - OFF, Red LED - ON
Green LED - OFF, Red LED - OFF
1. Present Master 2 Card + ANY 4 digit Code 3 times 2. Present Delete Card + ANY 4 digit Code -
Green LED - OFF, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Master 2 Card + ANY 4 digit Code -
Green LED - OFF, Red LED - OFF
-
Green LED - OFF, Red LED - ON
Green LED - OFF, Red LED - OFF
Delete ALL Users assigned to DOOR1
1. Present Delete Card + ANY 4 digit Code 2. Present Master 1 Card + ANY 4 digit Code 3 times
3. Present Delete Card + ANY 4 digit Code Delete ALL Users assigned to DOOR2
1. Present Delete Card + ANY 4 digit Code 2. Present Master 2 Card + ANY 4 digit Code 3 times 3. Present Delete Card + ANY 4 digit Code Set Door1 Open Time
Present the card X times for X seconds
(Door open Time)
Set Door1 in Toggle (ON/OFF) Mode
1. Present Master 1 Card + ANY 4 digit Code 3 times
2. Present Master 1 Card + ANY 4 digit Code Set Door2 Open Time
Present the card X times for X seconds
(Door open Time)
Set Door2 in Toggle (ON/OFF) Mode
1. Present Master 2 Card + ANY 4 digit Code 3 times 2. Present Master 2 Card + ANY 4 digit Code Reset All APB statuses
1. Present Reset APB card + ANY 4 digit Code on any reader
www.xprgroup.com
11
Set door left open Alarm
To set 40 seconds for door left open time:
1. Present Master1&amp;2 Card + ANY 4 digit Code 3 times 2. Present Delete Card + ANY 4 digit Code 4 times -
Green LED - OFF, Red LED - ON
Green LED - blinks twice, Red LED - ON
3. Present Master1&amp;2 Card + ANY 4 digit Code -
Green LED - OFF, Red LED - OFF
To disable the alarm:
Present Master1&amp;2 Card + ANY 4 digit Code 3 times Present Master1&amp;2 Card + ANY 4 digit Code -
Red LED - ON
Red LED - OFF
(4 x 10 sec. = 40 sec.)
This product herewith complies with requirements of EMC directive 2014/30/EU. In addition it complies with RoHS2 directive EN50581:2012
www.xprgroup.com
12
">

Hello! I am an AI chatbot specifically trained to assist you with the xpr SC24000 Owner's manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

2 Door Control
4000 User Capacity
Anti-Passback
Wiegand Reader Support
Adjustable Door Relay Time
Double Security Mode (LCSP)
Master Cards
Shadow Cards
Programming with Keypad

Frequently asked questions

The SC24000 can store up to 4000 users (cards).

The SC24000 supports both Wiegand 26bit and Wiegand 34bit readers. However, you should not connect different Wiegand types of readers. Both readers should be the same type.

The maximum block of cards that can be enrolled sequentially is 100 cards.

To factory reset the SC24000, turn OFF the power supply, put DIP Switch 6 in position ON, turn ON the power supply, then put DIP Switch 6 in position OFF. Wait for the Red LED to go OFF.

To set the door open time, present the appropriate Master card 3 times, then present the Delete card, then present the Master card again. Present the card the desired number of times for the corresponding number of seconds.