XPR XS-MF-RS-X Owner's Manual

The xpr XS-MF-RS-X is a reader designed for access control systems, enabling secure entry and exit through the use of Xsecure and Mifare DESFire credentials. It can be integrated with the WS4 controller and features flexible configuration options, including ID type and communication protocol settings. The XS-MF-RS-X reader offers reliable performance and seamless integration with various security systems.

PDF

Document

Setup of XS-K-MF-RS and XS-K-MF-RS-X Keypads, and XSMF-RS and XS-MF-RS-X Readers to the WS4
EN
This document describes how to set up the XS-K-MF-RS-X and XS-MF-RS-X readers with
Xsecure credential, and XS-K-MF-RS and XS-MF-RS readers without Xsecure credential to the
WS4.
Required items:
1. XS-K-MF-RS-X / XS-MF-RS-X and XS-K-MF-RS/XS-MF-RS readers.
2. Product Manager WS4. Product Manager WS4 software will be delivered upon request.
Contact us at [email protected]
3. Micro USB cable (optional). Make sure the cable supports data transfer. If the PC cannot
establish a connection with the reader, change the cable.
4. PROX-USB-X desktop reader PROX-USB - XPR Group (optional).
5. Xsecure and Mifare DESFire cards or fobs.
6. A separate Mifare DESFire card if you want to configure the reader with a card.
1. CONFIGURING THE READERS
Note: The readers are already configured with the required settings. If the reader was not re-configured, you can skip this
step and go to step 4 (Adding readers to the WS4 controller) below.
1.1 Install the Product Manager WS4 software.
1.2 Run the Product Manager WS4.
1.3 Select the “XSMART readers” group and the reader model.
1.4 Click the “OPEN” tab.
www.xprgroup.com
Rev. 1.13
1
1.5 Connect the reader to the PC using a micro-USB cable. If the reader is
recognised by the PC, the “Serial Port (COM)” field will show the communication port where the reader is connected, like “COM4”. If there is no value in the
“Serial Port (COM)” field, change the USB cable.
2. CONFIGURING A READER TO READ XSECURE CREDENTIALS
2.1 Click the “Connect to the reader” tab.
2.2 Set the interface to “WS4”.
2.3 Set the 13.5 MHz protocol to “ISO14443-A (Mifare,
NTAG)”.
2.4 Set the ID type to “Xsecure”.
2.5 Click the “Update” tab to configure the reader.
2.6 Mount the reader and connect it to the Controller.
3. CONFIGURING A READER TO READ MIFARE CSN
3.1 Click the “Connect to the reader” tab.
3.2 Set the Interface to “WS4”.
3.3 Set the 13.5 MHz protocol to “ISO14443-A (Mifare,
NTAG)”.
3.4 Set the ID type to “CSN, no encryption”.
3.5 Click the “Update” tab to configure the reader.
3.6 Mount the reader and connect it to the Controller.
www.xprgroup.com
2
4. ADDING READERS TO THE WS4 CONTROLLER
4.1 Go to the section “Doors” on the main screen of WS4
and select the available address where the reader will
be configured.
4.2 A new window will pop up.
4.3 Type the name of the access (entry, exit, main building, etc.).
4.4 For the card type, select “Mifare/DESFire”.
4.5 If you use a keypad, check the “Keypad” box.
4.6 Click the “Save” icon.
5. ASSIGNING THE XSECURE CREDENTIAL TO A USER MANUALLY
In the “Card 1” or “Card 2” field, enter the first number from the Xsecure card.
www.xprgroup.com
3
6. ASSIGNING THE XSECURE CREDENTIAL TO A USER WITH THE DESKTOP READER PROX-USB-X
• To read an Xsecure card, click the “Card 1” field, place the Xsecure card on
the PROX-USB-X desktop reader and the Xsecure ID will be written in the “Card
1” field.
• If the Xsecure number is not written, do the Desktop reader setup as described in the next section.
7. DESKTOP READER SETUP (XSECURE)
7.1 Download and run “PROX-USB-X Configurator” from XPR Group.
Downloads. The software runs on Windows OS.
7.2 Connect the desktop reader to the PC.
7.3 Set the values as given in the image below.
7.4 Click the “Update reader” tab under “Reading configuration”.
7.5 Click the “Update reader” tab under “Keypad configuration”.
8. ASSIGNING THE MIFARE CREDENTIAL TO A USER MANUALLY
In the “Card 1” or “Card 2” field, enter the number from the Mifare DESFire
card if it is printed.
9. ASSIGNING THE MIFARE CREDENTIAL TO A USER WITH DESKTOP READER PROX-USB-X
• To read a Mifare DESFire card, click the “Card 1” field,
place the card on the PROX-USB-X desktop reader and the
Mifare ID will be written in the “Card 1” field.
• If the Mifare number is not written, do the Desktop reader
setup as described in the next section.
www.xprgroup.com
4
10. DESKTOP READER SETUP (MIFARE CSN)
10.1 Download and run “PROX-USB-X Configurator” from XPR
Group. Downloads. The software runs on Windows OS.
10.2 Connect the desktop reader to the PC.
10.3 Set the values as given in the image below.
10.4 Click the “Update reader” tab under “Reading configuration”.
10.5 Click the “Update reader” tab under “Keypad configuration”.
www.xprgroup.com
5
">

Hello! I am an AI chatbot specifically trained to assist you with the xpr XS-MF-RS-X Owner's manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant is out of keyboard. Please, try again later.

Key features

Xsecure & Mifare support
WS4 compatible
Flexible configuration
ID type selection
13.5 MHz protocol
Data transfer via USB
Desktop reader setup

Frequently asked questions

You need to configure the reader first, setting the interface to 'WS4' and the 13.5 MHz protocol to 'ISO14443-A (Mifare, NTAG)'. Then, mount the reader and connect it to the WS4 controller.

The XS-MF-RS-X reader supports Xsecure and Mifare DESFire credentials. You can configure it to read either type by setting the ID type in the software.

Set the ID type to 'Xsecure', the interface to 'WS4', and the 13.5 MHz protocol to 'ISO14443-A (Mifare, NTAG)' in the Product Manager WS4 software. Then, click 'Update' to apply the configuration.