Solas One-Touch Remote Guide

The Solas One-Touch Remote is a powerful tool to control your fireplace. This remote allows you to turn your fireplace on and off, adjust the flame height, and set a timer for automatic shut-off. You can also program the remote to turn your fireplace on and off at specific times. The remote also has a child-proof feature to prevent unauthorized use.

PDF Download

Document

O N E - TOU C H R E M OT E
SUP PLE M E NTA L M A NUA L
Your Fireplace has been equipped with the S&Oacute;LAS next generation control system.
Please refer to this supplemental manual for operation of the S&Oacute;LAS One-Touch Remote.
Congratulations on your
purchase of a S&Oacute;LAS Fireplace!
We welcome you to the S&Oacute;LAS family
of gas fireplaces. Each of our products
are skillfully designed and expertly
manufactured in the USA. We take great
pride in every fireplace we make, with
every product being fully tested throughout
the production process to ensure your
safety and warmth throughout the years.
Sincerely,
The S&Oacute;LAS Team
LIGHTING &amp; OPERATION
FIRST FIRE INSTRUCTIONS
When operating your new fireplace for the first time, some
vapors may be released due to the curing compounds
used in the manufacture of the appliance. They may cause
a slight odor and could cause the flames to be the full
height of the firebox, or even slightly higher, for the first few
hours of operation. It is possible that these vapors could
set off smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room during the
burn off period. After a few hours use, the vapors will have
disappeared and the flames will be at their normal height.
It is important that the Comfort Blower is turned on to help
clear the vapors from the unit.
Follow these instructions for a successful first fire;
1. Turn the fireplace on in Manual Mode.
2. Set flame height to HI.
3. Set the Comfort Blower speed control to level
4.Let the fireplace run for 3 hours at this setting then shut
off fireplace and let it cool.
5.After the fireplace cools, turn the fireplace on in manual
mode with flame on HI and the Comfort Blower off.
6.Allow fireplace to run for 6 hours in this setting.
NOTE: Slight Odors may still be noticed on future uses
of the fireplace but will diminish over time. The type of
finishing materials used around the fireplace may add
odors or add to the curing time. If the fireplace has not
been used in several months, it is normal for odors to
occur caused by lint or dust that has settled on the unit
while not in use.
SERVICING
If any attention is required for your appliance, contact your
dealer quoting the model number and serial number. This
number is on the rating plate, which is located adjacent
to the control module. The replacement parts are shown
at the end of this manual. Please always quote the part
number and description when requesting spare parts.
Warranty is void if serviced by a non-qualified technician.
FIREPLACE CONTROL DEVICES
There are two ways to control your fireplace.
1. S&Oacute;LAS One-Touch Remote (S-507)
2. Optional Wall Touch Pad (WTP-1500)
The S&Oacute;LAS One-Touch Remote can be programmed to
function automatically—see pages 34-38.
The Optional Wall Touch Pad can be used to turn the flame
on, off, and to increase or decrease the flame height.
NOTE: The S&Oacute;LAS One-Touch Remote in the
AUTO mode will override the Wall Touch Pad.
NOTE: The Wall Touch Pad is not compatible
with the S&Oacute;LAS Self-Calibrating Power Vent
System.
FLAME SUPERVISION DEVICE
For your safety, this appliance is fitted with a flame
supervision device which will shut-off the gas supply if, for
any reason, the pilot flame goes out. This device incorporates
a fixed probe, which senses the heat from the pilot flame. If
the probe is cool, the device will prevent any gas flow unless
manually lighting the pilot. See full lighting instructions.
AM
PM
UP
ON-OFF
NOTE: Periodically conduct a visual check to ensure the
pilot and burner flames are as shown (top of page 3).
DOWN
During extreme cold weather, it is recommended that you
leave the pilot running to prevent condensation forming in
the firebox and on the glass viewing area during startup.
LIGHTING, OPERATION &amp; RATING INFO
The Lighting, Operation and Rating information is located
on a plate in front of the Comfort Blower inside the front
face of the fireplace.
To access the plate, remove lower air trim panel as shown
in step 1 on page 26.
2
S&Oacute;LAS One-Touch
Remote Part #S-507
S &Oacute; L AS CO NTE MPO R ARY F IR E
Wall Touch Pad
Part #WTP-1500
(Optional)
LIGHTING &amp; OPERATION
Flame
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.
When lighting this appliance, follow instructions exactly.
Flame
A. This appliance is equipped with an ignition device that
automatically lights the pilot. Do not try to light the pilot
by hand.
Pilot Light
B. BEFORE OPERATING THE BURNER SYSTEM, smell
around the appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than air and
will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
Pilot Light Location
• Do not try to light the appliance.
• Do not touch any electric switch; do not use any telephone
in your building.
•
Immediately call your gas supplier from a neighbor’s
telephone. Follow the gas supplier’s instructions
•
If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to operate the gas controls. Never
use tools. If a knob will not push in or turn by hand, don’t
try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system which has been under water.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. This appliance is equipped with an ignition device that
automatically lights the pilot. Do not try to light the pilot
by hand.
NOTE: If the pilot does not stay lit after several tries,
proceed to step 9.
7. Use the flame height adjustment buttons on either the
Remote or the optional Wall Touch Pad to adjust the flame.
To increase flame height, press and hold . To decrease
flame height, press and hold .
8. Press and hold the
button on the Remote or optional
Wall Touch Pad to set the appliance to Pilot flame only.
9. If the appliance will not operate, follow the instructions
“TO TURN OFF GAS TO THE APPLIANCE&quot; and call your
gas service technician or gas supplier.
TO TURN OFF GAS TO THE APPLIANCE
1. To turn off gas to the appliance, push and release the
“OFF&quot; button on either the Remote or the optional Wall
Touch Pad. An audible signal will confirm.
2. TO TURN OFF THE GAS SUPPLY TO THE APPLIANCE,
close the shut-off valve on the gas supply line to the
appliance.
3. Using the Remote, or the optional Wall Touch Pad, push
the “ON/OFF&quot; button until you hear an audible signal to
insure the appliance is off.
4. Wait five (5) minutes to clear out any gas. Then smell for
gas including near the floor. If you smell gas, STOP! Follow
“B&quot; in the safety information above. If you don’t smell gas,
proceed to step 5.
5. Using either the Remote or the optional Wall Touch Pad,
press and hold the “ON/OFF&quot; button for 4 seconds. An
audible signal confirms the start sequence has begun.
6. Continuing beeps confirm the ignition is in process. Once
lighting the pilot flame should appear as shown below.
Once the pilot is confirmed, the main burner ignites on high.
solasfires.com
AM
PM
HI Flame
ON/OFF
LO Flame
3
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
S&Oacute;LAS ONE-TOUCH REMOTE
PAIRING SET-UP
The Control Module and the Remote must be paired
before the first use. This has been completed for you
at the factory. Refer to the section below if the Control
Module and Remote lose synchronization.
1. Insert two AAA alkaline batteries in the Remote. Only
use brand name alkaline batteries, such as Duracell or
Energizer.
2. Four AA alkaline batteries are installed in the Control
Module (shown below).
NOTE: The four AA batteries are only used for battery
backup purposes in the event of a power outage.
3. Locate the RESET button on the front side of the
Control Module.
4. Press and hold the Control Module’s RESET button until
you hear one short beep and one long beep. After the
second beep, release the reset button.
5. Within the subsequent 20 seconds, press and hold
the button on the Remote for 2-3 seconds.
will be displayed and flash on the Remote during the
pairing sequence. The Remote will count up from 1 to
8, and you will hear two short beeps confirming the
pairing is complete.
S&Oacute;LAS One-Touch
Programmable
Thermostatic Remote
Part #S-507
If you hear one long beep, the pairing sequence has
failed or the wiring is incorrect.
This is a one time pairing and is not required when
changing the batteries of the Remote or Control Module.
The remote control system is now ready to use.
NOTE: The batteries in your S&Oacute;LAS one touch
remote control and control module are to be
replaced annually.
RESET Button
S&Oacute;LAS One-Touch
Control Module
Part #S-504
4
S &Oacute; L AS CO NTE MPO R ARY F IR E
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
HOW TO TURN YOUR FIREPLACE OFF
(INCLUDING PILOT)
Familiarize yourself with each of these methods before
operating your fireplace.
AM
PM
Remote and Wall Touch Pad*: Press and hold the ONOFF button for a second (either on the Remote or the
optional Wall Touch Pad).
Countdown
Timer
If the flames are on, they go down and you hear the valve
motor wind down. You hear a clunk and a beep indicating
that the valve has received the signal from the Remote.
Thermostatic
Mode
ON/OFF
Increase Flame
Program
Mode
Decrease Flame
Split Flow Mode
(not used)
Auxiliary Feature
(not used)
HOW TO ENSURE YOUR FIREPLACE
CANNOT BE TURNED ON
INADVERTENTLY
Main Display
Light (not used)
Comfort Blower
You can use the following method to ensure that your
fireplace will not turn on when you don’t want it on.
First, ensure your fireplace is turned off—including the
pilot—and cold BEFORE going ahead.
S&Oacute;LAS One-Touch
Programmable
Thermostatic Remote
Part #S-507
• Close the shut-off valve on the gas supply line to
the appliance.
• Remove all batteries from the Control Module as well as
the batteries from the Remote.
• Shut off power at the breaker.
Automatic Shut-Off (in certain conditions)
Your fireplace’s Remote is equipped with an automatic
shut-off mechanism which is activated in certain
conditions. See page 38 in the Remote Control Operation
section for a description of this feature.
UP
ON-OFF
NOTE: Before using the remote control system for
the first time, the Control Module and the Remote are
synchronized at the factory. See the section S&Oacute;LAS
Remote Pairing Set-up on page 32 of this manual if the
Control Module and Remote lose synchronization.
DOWN
IMPORTANT: BEFORE YOU BEGIN, please note that
with this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when the
function display is flashing. Be patient when programming
as it does take time to set-up.
S&Oacute;LAS Wall Touch Pad*
(Optional)
Part #WTP-1500
*Not Compatible with S&Oacute;LAS Self-Calibrating Power Vent Kit
solasfires.com
5
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
ONE-TOUCH REMOTE MAIN DISPLAY OVERVIEW
Child Proof
Time
Signal Indicator
Thermostatic Mode
Battery Status
AM
PM
Countdown Timer
Comfort Blower
&deg;F or &deg;C
Program Mode
Light (not used)
ON
OFF
Split Flow Mode
(not used)
Temperature
Auxiliary Feature (not used)
DO NOT leave the Remote on the hearth, mantel, or on top of the
fireplace. Use the Remote wall mount holder provided.
6
S &Oacute; L AS CO NTE MPO R ARY F IR E
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
TO TURN ON FIREPLACE
TO TURN OFF FIRE
• Press
to turn OFF.
When the pilot is off, it will
take 2 minutes before it
can be lit again.
CAUTION
WHEN PILOT IGNITION IS CONFIRMED, MOTOR
TURNS AUTOMATICALLY TO MAXIMUM FLAME
HEIGHT.
NOTE: There is a 2 minute delay
One-Touch Lighting (default):
AM
PM
after switching off before the next
ignition is possible.
Press and hold
for 4 seconds,
until 8 short beeps and a blinking
series of lines confirms the start
sequence has begun. Release
button.
Main gas flows once pilot ignition
is confirmed.
Remote automatically goes into
manual mode after main burner
ignition. The fireplace will default
to HI flame.
CAUTION
Always check the fire and pilot visually to ensure they
are off.
FLAME HEIGHT ADJUSTMENT
AM
PM
To decrease flame height, press and
hold . You may hold the button
down until the fire is set to pilot
flame only.
STANDBY MODE (PILOT FLAME)
AM
PM
To increase flame height, press and
hold .
Press and hold
to set
appliance to pilot flame.
DESIGNATE LOW AND HIGH FIRE
AM
NOTE: Flame goes to high fire first
before going to designated low fire.
CAUTION
If the pilot does not stay lit after several tries call your
local service technician or gas supplier.
AM
solasfires.com
Double-Click DOWN Arrow
button. “LO&quot; is displayed.
Double-Click UP Arrow
button.
Flame automatically goes to high
fire. “HI&quot; will be displayed.
7
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
SETTING CELSIUS OR FAHRENHEIT
To change between &deg;C and &deg;F, press and hold
simultaneously.
+
Note: W
hen Remote is in &deg;C
(Celsius) mode the clock will
be 24-hour. When Remote is
in &deg;F (Fahrenheit) mode the
clock will be 12-hour.
AM
PM
CHILD PROOF
Your Remote can be set to lock out all commands to the
fireplace, except OFF.
To turn Child Proof ON:
1. Press and hold
2.
+
simultaneously.
is displayed. Child Proof is now active.
To turn Child Proof OFF:
1. Press and hold
+
simultaneously.
2. disappears. Child Proof is now inactive, and the
Remote has full function.
COUNTDOWN TIMER
You can set your fireplace to automatically turn off at the
end of a timer.
To set a Countdown Timer:
SETTING THE TIME
1. Press
+
simultaneously. Day flashes.
2. Press + to select a number to correspond
with the day of the week.
• 1 = Monday
• 2 = Tuesday
• 3 = Wednesday
• 4 = Thursday
• 5 = Friday
• 6 = Saturday
• 7 = Sunday
3. Press
+
simultaneously. Hour flashes.
4. To select hour press
5. Press
+
or
6. To select minutes press
or
7. To confirm, press
simultaneously or wait.
AM
is
2. Press or
to select Hour.
3. To confirm, press . Minutes flash.
4. Press or
to select Minutes.
5. To confirm, press
or wait.
To turn off a Countdown Timer:
1. Press , and the
disappears.
countdown
NOTE: The Countdown Timer only works in Manual and
Thermostatic modes. Maximum countdown time is
9 hours and 50 minutes.
.
simultaneously. Minutes flash.
or
1. Press and hold
until
displayed. Hour flashes.
.
COMFORT BLOWER OPERATION
Setting:
1. Press and hold
until
flashes.
2. Press
to increase or
to
decrease Comfort Blower speed.
3. To confirm setting, either press
or wait.
is displayed.
OFF: P
ress
until all 4 speed level
bars disappear.
NOTE: When setting, if the Comfort
Blower was not switched off
after last use, it starts automatically 4 minutes
after ignition at maximum speed, and goes to
the last set level after 10 seconds. The Comfort
Blower stops 10 minutes after the main burner is
extinguished.
8
S &Oacute; L AS CO NTE MPO R ARY F IR E
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
MODES OF OPERATION
Manual Mode
The ON/OFF status of the fireplace, as well as flame
height, are manually controlled by the user.
NOTE: The set temperature for Thermostatic Mode is the
temperature for the ON time in Program Mode.
Changing the Thermostatic Mode set temperature
also changes the ON time temperature in
Program Mode.
Default Settings:
Thermostatic Mode
The room temperature is measured
and compared to the set temperature.
The flame height is automatically
adjusted to achieve the set
temperature.
• ON TIME (Thermostatic) TEMPERATURE: 70&deg;F / 21&deg;C
• OFF TIME TEMPERATURE: “
&quot; (pilot flame only)
Temperature Setting:
ON:
Press . is displayed. Preset
temperature displays briefly, followed by the room
temperature.
Setting Desired Temperature:
1. Press and hold
until
flashes. ON and
set temperature (set in Thermostatic Mode)
is displayed.
2. To continue, press
or wait.
displayed, temperature flashes.
, OFF
1. Press and hold until is displayed
and set temperature flashes.
2. To adjust set temperature,
press or .
3. To confirm, press or wait.
3. Select off temperature by pressing
OFF:
Day Setting:
1. Press
4. To confirm, press
or
3. Press
to go to Program Mode.
to go to Manual Mode.
Program Mode
The temperature is controlled by
Programs 1 and 2, each of which can
be set to go on and off at specific
times, at a set temperature.
or
.
.
NOTE: The on (Thermostatic) and off set temperatures
are the same for each day.
.
2. Press
ON
ON
OFF
1. ALL flashes. Press or
to choose
between:
• ALL = same settings ON-OFF every day
• SA:SU = same settings ON-OFF Saturday
and Sunday
• 1 , 2, 3, 4, 5, 6, 7 = daily timer—unique
ON-OFF settings for a single day of the
week, for multiple days of the week or for
every day of the week.
2. To confirm, press
.
ALL Selected
On Time Setting (PROGRAM 1)
1. , 1, ON are displayed.
ALL is displayed briefly. Hour flashes.
PROGRAM MODE
ON:
Press .
, 1 or 2, ON or OFF are displayed.
OFF:
1. Press , or
Manual Mode.
to go to
2. Press to go to Thermostatic Mode.
2. To select hour, press
ON
OFF
or
ON
.
3. To confirm, press .
, 1, ON are
displayed. ALL displayed briefly.
Minutes flash.
4. To select minutes, press
5. To confirm, press
solasfires.com
or
.
.
9
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
LOW BATTERY INDICATION
PROGRAM MODE (Continued)
Off Time Setting (PROGRAM 1)
1. , 1, OFF are displayed. ALL is
displayed briefly. Hour flashes.
2. To select hour, press
or
CAUTION
OFF
.
3. To confirm, press .
, 1, OFF
are displayed. ALL displayed
briefly. Minutes flash.
4. To select minutes, press or .
5. To confirm, press
or
.
NOTE: Either continue to PROGRAM 2 and set ON and
OFF times or stop programming at this point, and
PROGRAM 2 remains deactivated.
NOTE: PROGRAM 1 and 2 use the same ON
(Thermostatic) and OFF temperatures. Once a
new ON (Thermostatic) and/or OFF temperature
has been set, that temperature becomes the new
default setting.
NOTE: ON and OFF times programmed for PROGRAM 1
and PROGRAM 2 become the new default times.
The batteries must be removed to clear the PROGRAM 1
Do not use a screwdriver or other metallic object
to remove the batteries from the Control Module
battery holder or the Remote. This could cause a
short circuit.
NOTE: The batteries in your S&Oacute;LAS One-Touch
remote control and control module are to be
replaced annually. Only use brand name alkaline
batteries such as Duracell or Energizer.
Remote
The battery icon
will show when the battery needs
to be replaced. Replace with two 1.5 V AAA alkaline
batteries.
Control Module
Frequent beeps for 3 seconds when the motor turns
indicate the batteries in the battery holder of the Control
Module need to be replaced. Replace with four 1.5 V AA
alkaline batteries.
and PROGRAM 2 ON and OFF times and temperatures.
AUTOMATIC SHUT-OFF
SA: SU or Daily Timer (1-7) Selected
• Set ON time and OFF time using the same procedure
as “ALL Selected&quot; above.
• Waiting to finish setting.
Countdown Timer
At the end of countdown time period, the fire turns
off. The Countdown Timer only works in Manual and
Thermostatic. Maximum countdown time is 9 hours and
50 minutes.
Seven Day Shut Off
If there is no activity for 7 days, the S&Oacute;LAS fireplace will
automatically shut down the pilot as required by certain
jurisdictions.
AUTOMATIC TURN DOWN
3 Hour No Communication Function
If your fireplace and remote are inactive for three hours—
for example, if the remote is left in another room—your
fireplace automatically turns down to pilot.
Benefit
S&Oacute;LAS products are designed with a focus on safety and
environmental responsibility. This will help save fuel and
is an environmental benefit. Program the temperature
and timer modes to maximize your heating efficiency.
10
S &Oacute; L AS CO NTE MPO R ARY F IR E
S&Oacute;LAS ONE-TOUCH REMOTE OPERATION
ERROR
CODE
F04
MESSAGE
F04
DURATION OF
DISPLAY
SYMPTOM
POSSIBLE CAUSE
4 seconds
• No pilot flame within 30 sec
• Note: After 3 failed ignition
sequences, F06 shown
• No gas supply
• Air in pilot supply line
• No spark
• Reversed polarity in thermocouple
wiring
• No gas supply
• Air in pilot supply line
• No spark
• Reversed polarity in
thermocouple wiring
• Incorrect pilot orifice if valve has
been converted from LPG to NG
or vice versa
F06
F06
4 seconds
• 3 failed ignition sequences
in 5 minutes
• Fire is not responding,
no pilot flame
F07
Low Battery
Symbol
Permanent
• Battery icon flashes on
Remote display
• Low battery in Remote
F09
F09
4 seconds
• Fire is not responding
• No electronic control of fire
• Down arrow button
was not
pressed during pairing
• Control Module and Remote are
not synced
• Fire is not responding
• Intermittent response
• No electronic control of fire
• No or bad connection between
Control Module and Remote
• No power at Control Module
• Low communication range
(Control Module Faulty, Remote
not communicating with
Control Module)
F46
F46
4 seconds
S&Oacute;LAS ONE-TOUCH REMOTE TIPS
• Double-click
flame setting.
to go directly to LO (lowest)
• Don’t leave the Remote on the mantel or hearth or any
hot surfaces. Use the Remote wall holder provided.
• Double-click
flame setting.
to go directly to HI (highest)
• To keep out of children’s reach, use the Remote wall
holder provided.
• The batteries in your S&Oacute;LAS one touch remote control
and control module are to be replaced annually. Only
use brand name alkaline batteries such as Duracell or
Energizer.
• Be patient when programming: it takes time to set-up.
• Once you turn a pilot off, it takes a few minutes before
your can turn it back on.
• When using the Remote, it should be within 15 feet
(4.5 meters) of the fireplace.
Your S&Oacute;LAS Dealer is here to help, if you have any trouble with your S&Oacute;LAS
Fireplace or S&Oacute;LAS One-Touch Remote. Please contact your Dealer for support.
solasfires.com
11
We recommend that our
gas hearth products be
installed and serviced by
professionals who are
certified in the U.S. by the
National Fireplace Institute&reg;
(NFI) as NFI Gas Specialists.
www.NFIcertified.org
THANK YOU FOR CHOOSING
solasfires.com
">

Hello! I am an AI chatbot specifically trained to assist you with the Solas One-Touch Remote Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Remote control
Flame height adjustment
Timer
Programmable
Child-proof

Frequently asked questions

The remote is pre-paired at the factory. However, if the pairing is lost you can reset the Control Module, press the reset button until hear one short and one long beep. Then within 20 seconds press and hold the button on the Remote for 2-3 seconds until you hear two short beeps confirming the pairing is complete.

Press the "+" and "-" buttons simultaneously. When the "Hour" is flashing, use the "+" and "-" buttons to select the time and confirm with "OK".

To increase the flame height, press and hold the "UP" button. To decrease the flame height, press and hold the "DOWN" button.