Solas TWENTY6 Installation Manual

TWENTY6 SLIM-LINE
BUILT-IN DIRECT-VENT
GAS FIREPLACE with COOL ZONE
INSTALLATION & OPERATION MANUAL
MODELS: BI-26N-SS, BI-26P-SS
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury, death, or property damage.
— Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a neighbor’s
phone. Follow the gas supplier’s instructions.
• If you cannot reach your gas supplier, call the fire
department.
— Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
DUE TO HIGH TEMPERATURES, THE APPLIANCE SHOULD BE
LOCATED OUT OF TRAFFIC AND AWAY FROM FURNITURE
AND DRAPERIES.
CHILDREN AND ADULTS SHOULD BE ALERTED TO THE
HAZARD OF HIGH SURFACE TEMPERATURE AND SHOULD
STAY AWAY TO AVOID BURNS OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED
WHEN THEY ARE IN THE SAME ROOM WITH THE APPLIANCE.
CLOTHING OR OTHER FLAMMABLE MATERIAL SHOULD NOT
BE PLACED ON OR NEAR THE APPLIANCE.
KEEP THE ROOM AREA CLEAR AND FREE FROM
COMBUSTIBLE MATERIALS, GASOLINE, AND OTHER
FLAMMABLE VAPORS AND LIQUIDS.
WARNING Improper installation, adjustment, services or
maintenance can cause injury or property damage. Refer to
this manual. For assistance or additional information, consult
a qualified installer, service agency or the gas supplier.
Report #F19-217
Ce manual est disponsible en Francais sur demande.
This appliance may be installed in an aftermarket, permanently
located, manufactured home (USA only) or mobile home, where
not prohibited by local codes.
This appliance is only for use with the type of gas indicated on
the rating plate. This appliance is not convertible for use with
other gases, unless a certified kit is used.
DANGER
HOT GLASS
WILL CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and must be installed for the protection
of children and other at-risk individuals.
INSTALLER: Leave this manual with appliancesolasfires.com
‌| CONSUMER: Retain this manual for future reference
1
INSTALLATION RECORD
The installer should complete the form below that describes the details of the installation. Having
this written record of installation information available will greatly expedite trouble-shooting
should any problem arise with your stove. The installer should keep a duplicate of this form for
their records.
Date Purchased: ______________________________________________________
Dealer:______________________________________________________________
Date Installed: ________________________________________________________
Installer: _____________________________________________________________
Fireplace Model:
TWENTY6 SLIM-LINE BUILT-IN
Burner: (circle one) Glass Media Burner
Log Set Burner
Serial Number: ________________________________________________________
Brand of Venting Used: _________________________________________________
Model # of Vent Cap Used: ______________________________________________
Fuel: (circle one)
Natural Gas (NG)
Was this field converted? (circle one)
Propane (LP)
YES
NO
Inlet Pressure (after installation):___________________________________________
Manifold Pressure (after Installation):
High Fire: ______________________ in. WC
Low Fire: _______________________ in. WC
Altitude: (feet above sea level) ____________________________________________
Was the Fireplace derated? (circle one)
YES
NO
If the Fireplace was derated, to what orifice size? _____________________________
Other installation notes:_________________________________________________
____________________________________________________________________
____________________________________________________________________
____________________________________________________________________
2
S Ó L AS CO NTE MPO R ARY F IR E
CONTENTS
Installation Record..............................................................2
Important Safety Information............................................5
Massachusetts Requirements..........................................8
Gas Connection...................................................................8
Specifications.......................................................................9
Clearances.......................................................................... 12
Electrical & Plumbing Info............................................... 16
Comfort Blower Info......................................................... 17
Venting................................................................................. 18
Assembly & Installation................................................... 25
Lighting & Operation........................................................37
Remote Operation............................................................. 41
Gas Conversion.................................................................47
Maintenance....................................................................... 51
Maintenance Log.............................................................. 53
Replacement Parts List................................................... 54
Control Schematic............................................................55
Warranty Information....................................................... 56
WE STRONGLY SUGGEST THAT YOU READ THIS
MANUAL THOROUGHLY BEFORE BEGINNING
THE INSTALLATION OF THIS DIRECT-VENT GAS
FIREPLACE. ALTHOUGH THE BASIC REQUIREMENTS
FOR THE INSTALLATION OF ALL DIRECT VENT
GAS FIREPLACES ARE SIMILAR, EACH SPECIFIC
PRODUCT HAS ITS OWN UNIQUE SET-UP AND
INSTALLATION REQUIREMENTS THAT MUST BE
FOLLOWED EXACTLY. PLAN YOUR INSTALLATION
IN ADVANCE BY CAREFULLY REVIEWING ALL THE
INFORMATION CONTAINED IN THIS MANUAL.
Congratulations on your purchase
of a SÓLAS Fireplace!
We welcome you to the SÓLAS family of gas fireplaces.
Each of our products are skillfully designed and expertly
manufactured in the USA. We take great pride in every
fireplace we make and each product is fully tested
throughout the production process to ensure your safety
and warmth throughout the years.
Sincerely,
The SÓLAS Team
WARNING
Dust or particles caught in the cool zone airflow may cause
staining or streaking on light colored ceilings or walls when
exiting the plenum outlet. Keeping as large a distance as
possible between the outlet and the ceiling will mitigate this
issue.
WARNING
DO NOT cover or place objects in front of the cool wall
plenum outlet. DISCHARGE TEMPERATURES ARE HOT!
Locate outlet plenum out of reach and away from high traffic
areas.
WARNING
THIS FIREPLACE MUST BE INSTALLED WITH THE COOLZONE PROVIDED. FAILURE TO INSTALL THE COOLZONE AS OUTLINED IN THIS MANUAL, REMOVAL OF,
OR MODIFICATION OF THE COOL-ZONE MAY RESULT IN
PROPERTY DAMAGE, INJURY, OR LOSS OF LIFE.
The information contained in this manual is believed to be
correct at the time of printing. SÓLAS LLC. reserves the right
to change or modify any information or specifications without
notice. SÓLAS LLC grants no warranty, implied or stated,
for the installation or maintenance of your appliance, and
assumes no responsibility for any consequential damage(s).
© 2023 Copyright SÓLAS LLC.
solasfires.com
3
Félicitations pour votre achat d’un SÓLAS !
Nous vous souhaitons la bienvenue dans la famille des foyers au gaz SÓLAS. Chacun
de nos produits est habilement conçu et fabriqué de manière experte aux États-Unis.
Nous sommes très fiers de chaque foyer que nous fabriquons. Chaque produit est
entièrement testé tout au long du processus de production pour garantir votre sécurité
et votre chaleur au fil des ans.
Sincèrement,
SÓLAS
AVERTISSEMENT: Assurez vous de bien suivre
les instructions données dans cette notice
pour réduir e au minimum le risque d’incendie
ou d’explosion ou pour éviter tout dommage
matériel, toute blessure ou la mort.
Ne pas entreposer ni utiliser d’essence ni
d’autres vapeurs ou liquids inflammables dans
le voisinage de cet ap pareil ou de tout autre
appareil.
— QUE FAIRE SI VOUS SENTEZ UNE ODEUR
DE GAZ:
• Ne pas tenter d’allumer d’appareil.
• Ne touchez à aucun interrupteur. Ne pas vous
servir des téléphones se trouvant dans le
bâtiment où vous trouvez.
• Appelez immédiatem ent votre fournisseur de
gaz depuis un voisin. Suivez les instructions du
fournisseur.
• Si vous ne pouvez rejoindre le fournisseur de
gaz, appelez le service des incendies.
Cet appareil peut être installé dans une maison
préfabriquée (mobile) déjà installée à demeure si les
règlements locaux le permettent.
Cet appareil doit être utilisé uniquement avec les types de
gaz indiqués sur la plaque signalétique. Cet appareil ne
peut être converti à d’autres gaz, sauf si une trousse de
conversion est utilesée.
Ne pas utilieser cet appareils il a été plongé, meme
partiellement, dans l’eau. Appeler un technician qualifié
pour inspecter l’appareail et remplacer toute partie du
système de commande et toute commande qui a été
plongée dans / ’eau.
ATTENTION: Au moment de l’entretien des commandes,
étiquetez tous les files avant de les débrancher. Des
erreurs de la câblage peuvent entraîner un fonctionnement
inadequate et dangereux.
S’assurer que l’appareil fonctionne adéquatement une fois
l’entretien terminé.
ATTENTION: Ne pas utiliser l’appareil si la panneau frontal
en verre n’est pas en place, est craqué ou brisé. Confiez le
remplacement du panneau à un technician agree.
— L’installation et l’entretien doivent être assurés
par un installateur ou un s ervice d’entretien
qualifié ou par le fournisseur de gaz.
INSTALLATEUR: LAISSEZ CE MANUEL AVEC L’APPAREIL.
CONSOMMATEUR: CONSERVEZ CE MANUEL AUX FINS DE CONSULTATION ULTÉRIEURE.
4
S Ó L AS CO NTE MPO R ARY F IR E
IMPORTANT SAFETY INFORMATION
The installation must conform with local codes or, in
the absence of local codes, with the National Fuel
Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas
and Propane Installation Code, CSA B149.1.
A manufactured home (USA only) or mobile home
OEM installation must conform with the Manufactured
Home Construction and Safety Standard, Title 24
CFR, Part 3280 or when such a standard is not
applicable, the Standard for Manufactured Home
Installations, ANSI/BCSBCS A225.1, or Standard for
Gas Equipped Recreational Vehicles and Mobile
Housing, CSA Z240.4.
The appliance and its appliance main gas valve must
be disconnected from the gas supply piping system
during any pressure testing of that system at test
pressures in excess of 1/2 psi (3.5 kPa).
The appliance must be isolated from the gas supply
piping system by closing its equipment shutoff valve
during any pressure testing of the gas supply piping
system at test pressures equal to or less than 1/2 psi
(3.5 kPa).
The installation must provide for adequate ventilation
air to the appliance.
This gas appliance must not be connected to a
chimney flue serving a separate solid-fuel burning
appliance.
Due to high temperatures, the appliance should be
located out of traffic and away from furniture and
draperies.
Children and adults should be alerted to the
hazards of high surface temperatures and should
stay away to avoid burns or clothing ignition.
Young children should be carefully supervised
when they are in the same room as the appliance.
Toddlers, young children and others may be
susceptible to accidental contact burns. A physical
barrier is recommended if there are at-risk
individuals in the house. To restrict access to a
fireplace or stove, install an adjustable safety gate
to keep toddlers, young children and other at-risk
individuals out of the room and away from hot
surfaces.
A barrier designed to reduce the risk of burns
from the hot viewing glass is provided with this
appliance and shall be installed for the protection
of children and other at-risk individuals. If the
barrier becomes damaged, the barrier shall be
replaced with the manufacturer’s barrier for this
appliance.
Clothing or other flammable material should not be
placed on or near the appliance.
The appliance, when installed, must be electrically
grounded in accordance with local codes, or, in the
absence of local codes, with the National Electrical
Code ANSI/NFPA 70, or the Canadian Electrical
Code, CSA C22. 1.
Any screen or guard removed for servicing an
appliance must be replaced prior to operating the
appliance.
The appliance area must be kept clear and free from
combustible materials, gasoline and other flammable
vapors and liquids.
The flow of combustion and ventilation air must not
be obstructed. Adequate accessibility clearances
must be maintained for servicing and proper
operation of this appliance.
Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of
the control system and any gas control which has
been under water.
solasfires.com
5
IMPORTANT SAFETY INFORMATION
Fireplace
Keep Furniture
and Other Objects
36" from Fireplace
36" (91.44cm)
Installation and repair should be done by a
qualified service technician. The appliance should
be inspected before use and at least annually by
a professional service technician. More frequent
cleaning may be required due to excessive lint from
carpeting, bedding material, etc. It is imperative that
the control compartments, burners and circulating
air passageways of the appliance be kept clean.
WARNING: Do not operate the appliance with
the glass door assembly removed, or if the glass
is cracked or broken. Replacement of the glass
should be done by a qualified service technician.
WARNING: Use only glass assembly, P/N BI26510, which includes the glass panel, frame and
gasket. Do not use substitute materials. Do not
strike or slam the glass front. Do not use abrasive
cleaners. Do not clean when hot.
CAUTION: Do not operate with broken glass.
6
S Ó L AS CO NTE MPO R ARY F IR E
CERTIFICATION
This appliance has been certified by PFS TECO to ANSI Z21.882016/CSA 2.33-2016 Vented Gas Fireplace Heaters and CAN/
CGA-2.17-2017, Gas-Fired Appliances for Use At High Altitudes.
elevation greater than these, consult with the local authority
having jurisdiction for gas product installations to determine
their specific requirements for high altitude installations.
This SÓLAS Gas Fireplace is approved for installation at
elevations up to 2000 feet in the U.S. and 1370 meters (4500
feet) in Canada without change. If your installation is at an
These appliances are approved for installation in the
Commonwealth of Massachusetts by the Board of State
Examiners of Plumbers and Gas Fitters.
SÓLAS
GASFIREPLACES
FIREPLACES
SÓLAS –DIRECT
DIRECT VENT
VENT GAS
MODEL NOS. BI-26N, BI-26P
NOT FOR USE WITH SOLID FUEL.
SER. NO.
BI-26-
THIS APPLIANCE IS EQUIPPED FOR:
PROPANE (LP) GAS
NATURAL GAS
Input Rating-Btu/hr
Min. Input Rating-Btu/
hr Orifice - DMS
Manifold Pressure
Min. Supply Pressure
Max. Supply Pressure
Natural Gas
19,000
11,000
5/64”
5.0”wc/1.3kPa
5.5”wc/1.4kPa
10.0”wc/2.5kPa
Propane
19,000
11,000
#55
10.0”wc/2.5kPa
11.0”wc/2.8kPa
13.0”wc/3.3kPa
Debit Calorifique
Puissance Minimum
L’injector
Press. A la tubulure
Press. D’Arrivée Min
Press. D’Arrivée Max
MODEL NOS. BI-26N, BI-26P
VENTED GAS FIREPLACE HEATER
NOT FOR USE WITH SOLID FUEL.
SER. NO.
BI-26-
THIS APPLIANCE IS EQUIPPED FOR:
PROPANE (LP) GAS
NATURAL GAS
Input Rating-Btu/hr
Min. Input Rating-Btu/
hr Orifice - DMS
Manifold Pressure
Min. Supply Pressure
Max. Supply Pressure
Natural Gas
19,000
11,000
5/64”
5.0”wc/1.3kPa
5.5”wc/1.4kPa
10.0”wc/2.5kPa
Propane
19,000
11,000
#55
10.0”wc/2.5kPa
11.0”wc/2.8kPa
13.0”wc/3.3kPa
Debit Calorifique
Puissance Minimum
L’injector
Press. A la tubulure
Press. D’Arrivée Min
Press. D’Arrivée Max
This product has been tested and listed by PFS TECO to ANSI
Z21.88-2016 · CSA 2.33-2016 Vented Gas Fireplace Heaters and CSA
2.17-2017, Gas-Fired Appliances For Use At High Altitudes and CSA
P.4.1-09. This appliance is equipped only for altitudes from 0-2000 feet
(0-610m) in the USA and 0-4500 feet (0-1370m) in Canada without
change. This appliance must be installed in accordance with local codes,
if none, follow the National Fuel Gas Code, ANSI Z223.1 or Canadian
Installation Codes, CAN/CSA-B149.1. This Appliance must be properly
connected to a venting system in accordance with the manufacturer’s
installation instructions.
This product has been tested and listed by PFS TECO to ANSI
Z21.88-2016 · CSA 2.33-2016 Vented Gas Fireplace Heaters and CSA
2.17-2017, Gas-Fired Appliances For Use At High Altitudes and CSA
P.4.1-09. This appliance is equipped only for altitudes from 0-2000 feet
(0-610m) in the USA and 0-4500 feet (0-1370m) in Canada without
change. This appliance must be installed in accordance with local codes,
if none, follow the National Fuel Gas Code, ANSI Z223.1 or Canadian
Installation Codes, CAN/CSA-B149.1. This Appliance must be properly
connected to a venting system in accordance with the manufacturer’s
installation instructions.
MINIMUM CLEARANCES TO
COMBUSTIBLE CONSTRUCTION:
0” (0mm)
Fireplace Surround to L. Side Wall
0” (0mm)
Fireplace Surround to R. Side Wall
0” (0mm)
Fireplace Surround to Corner Wall
0” (0mm)
Fireplace Surround to Ceiling Wall
0” (0mm)
Fireplace Surround to Rear Wall
0” (0mm)*
Fireplace Surround to Floor
MINIMUM CLEARANCES TO
COMBUSTIBLE CONSTRUCTION:
0” (0mm)
Fireplace Surround to L. Side Wall
0” (0mm)
Fireplace Surround to R. Side Wall
0” (0mm)
Fireplace Surround to Corner Wall
0” (0mm)
Fireplace Surround to Ceiling Wall
0” (0mm)
Fireplace Surround to Rear Wall
0” (0mm)*
Fireplace Surround to Floor
*The minimum required clearance to be maintained from the fireplace to
combustible flooring is measured from the top surface of carpeting, tile, etc.
SUPPLIED COOL ZONE KIT MUST BE INSTALLED.
*The minimum required clearance to be maintained from the fireplace to
combustible flooring is measured from the top surface of carpeting, tile, etc.
SUPPLIED COOL ZONE KIT MUST BE INSTALLED.
CAUTION:
Do not operate the
appliance with the glass removed, cracked
or broken. Replacement of the glass panel(s)
should be done by a licensed or qualified
service person. See the Owner’s Manual for
more information.
CAUTION:
Do not operate the
appliance with the glass removed, cracked
or broken. Replacement of the glass panel(s)
should be done by a licensed or qualified
service person. See the Owner’s Manual for
more information.
WARNING: Improper installation adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to the owner’s
information manual provided with this appliance. For assistance or
additional information, consult a qualified in-staller, service agency or the
gas supplier.
WARNING: Improper installation adjustment, alteration, service or
maintenance can cause injury or property damage. Refer to the owner’s
information manual provided with this appliance. For assistance or
additional information, consult a qualified in-staller, service agency or the
gas supplier.
Label all wires prior to
disconnection when servicing. Wiring errors
can cause improper and dangerous
operation. Verify proper operation after
servicing.
Label all wires prior to
disconnection when servicing. Wiring errors
can cause improper and dangerous
operation. Verify proper operation after
servicing.
CAUTION:
CAUTION:
Keep burner and control compartments clean. See installation and operating
instructions accompanying appliance.
Keep burner and control compartments clean. See installation and operating
instructions accompanying appliance.
This vented gas fireplace is not for use with air filters.
This vented gas fireplace is not for use with air filters.
This appliance is only for use only with the type of gas indicated on the
rating plate and may be installed in an aftermarket, permanently located,
manufactured home (USA only) or mobile home, where not prohibited by
local codes. See Owner’s Manual for details.
This appliance is only for use only with the type of gas indicated on the
rating plate and may be installed in an aftermarket, permanently located,
manufactured home (USA only) or mobile home, where not prohibited by
local codes. See Owner’s Manual for details.
This appliance is not convertible for use with other gases, unless a
certified conversion kit is used.
This appliance is not convertible for use with other gases, unless a
certified conversion kit is used.
This appliance must be properly connected to a Direct Vent, venting
system in accordance with the manufacturer’s installation instructions.
This appliance must be properly connected to a Direct Vent, venting
system in accordance with the manufacturer’s installation instructions.
FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY.
FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY.
CAUTION: HOT WHILE IN OPERA-
CAUTION: HOT WHILE IN OPERA-
TION. DO NOT TOUCH, SEVERE BURNS MAY
RESULT. KEEP CHILDREN, CLOTHING, FURNITURE, GASOLINE AND OTHER LIQUIDS
HAVING FLAMMABLE VAPORS AWAY.
Rpt. # F19-217
*Sample Rating Label (affixed to Control Panel within Firebox)
VENTED GAS FIREPLACE HEATER
SÓLAS
FIREPLACES
SÓLASDIRECT
– DIRECTVENT
VENT GAS
GAS FIREPLACES
TION. DO NOT TOUCH, SEVERE BURNS MAY
RESULT. KEEP CHILDREN, CLOTHING, FURNITURE, GASOLINE AND OTHER LIQUIDS
HAVING FLAMMABLE VAPORS AWAY.
MANUFACTURED BY:
MANUFACTURED BY:
Progressive Manufacturing Inc.
452 Sunapee Street
Newport, NH 03773
U.S.A.
Progressive Manufacturing Inc.
452 Sunapee Street
Newport, NH 03773
U.S.A.
Rpt. # F19-217
7
INSTALLATION REQUIREMENTS
STATE OF MASSACHUSETTS
The installation must be completed by a licensed
plumber or gas fitter in the Commonwealth of
Massachusetts.
REQUIREMENTS FOR THE COMMONWEALTH OF
MASSACHUSETTS
This product must be installed by a licensed plumber
or gas fitter when installed within the Commonwealth
of Massachusetts. If this appliance is installed in a
dwelling, building or structure used in whole or in part
for residential purposes and the installation includes a
horizontal vent termination that is less than seven (7)
feet above the finished grade in the area of the venting,
including but not limited to decks and porches, a hardwired carbon monoxide detector with an alarm and
battery back-up must be installed on the floor level of the
dwelling, building or structure where the appliance is to
be installed.
Additionally, a hard-wired or battery operated carbon
monoxide detector with an alarm must be installed
on each additional level of the dwelling, building
or structure served by the appliance. It shall be the
responsibility of the property owner to secure the
services of qualified licensed professionals for the
installation of hard-wired carbon monoxide detectors.
In the event that the horizontally vented appliance is
installed in a crawl space or attic, the hardwired carbon
monoxide detector with alarm and battery back-up may
be installed on the next adjacent floor level.
In the event that this requirement cannot be met at the
time of completion of the installation of the appliance,
the owner shall have a period of thirty (30) days to
comply with the requirement. However, during said thirty
(30) day period, a battery operated carbon monoxide
detector with alarm must be installed.
Each carbon monoxide detector as required in
accordance with the above provisions must comply with
NFPA 720 and be ANSI/UL 2034 and IAS certified.
In addition, when the vent termination is less than
seven (7) feet above finished grade a metal or plastic
identification plate must be permanently mounted to the
exterior of the building at a minimum height of eight (8)
feet above grade directly in line with the exhaust vent
terminal. The sign shall read, in print size no less than
one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW.
KEEP CLEAR OF ALL OBSTRUCTIONS".
8
The gas fireplace is shipped with a 3/8" tube OD (male
flare) connection. The gas supply piping should have a
separate gas shutoff valve and a 1/8" NPT plugged tapping
upstream of the valve. The stove and its main control
valve must be disconnected from the gas supply piping
system during any pressure testing of that system at test
pressures in excess of 1/2 psi (3.5 kPa). The stove must be
isolated from the gas supply piping system by closing the
main control valve during any pressure testing of the gas
supply system at test pressures equal to or greater than
1/2 psi (3.5 kPa). After the gas supply has been connected,
use a commercial gas leak detector or apply a soapy water
solution to all the fittings to check for gas leaks. Never use
a flame to test for leaks.
A COPY OF THESE INSTRUCTIONS PLUS ALL
VENTING INSTRUCTIONS WHICH INCLUDE
PARTS LISTS, AND/OR ALL VENTING DESIGN
INSTRUCTIONS MUST REMAIN WITH THE STOVE AT
THE COMPLETION OF THE INSTALLATION.
ATTENTION INSTALLERS: Mark below which venting
system was used in the installation. These instructions
must remain with the SÓLAS Gas Fireplace Installation
& Operation Manual.
O Simpson DuraVent GS/PRO®
O Selkirk Direct-Temp®
O Security Secure Vent™
O AmeriVent Direct™
O Metal Fab Direct Vent
O ICC Direct Vent
NOTICE
Failure to follow these instructions will void the
warranty.
S Ó L AS CO NTE MPO R ARY F IR E
SPECIFICATIONS
TWENTY6 SPECIFICATION CHART
INPUT
NATURAL GAS
PROPANE
Input Rating
19,000 BTU/Hr.
19,000 BTU/Hr.
Min. Input Rating
11,000 BTU/Hr.
11,000 BTU/Hr.
Orifice-DMS
5/64"
#55
GAS SUPPLY
NATURAL GAS
PROPANE
Manifold Pressure
4.8"w.c. / 1.2kPa
10.0"w.c. / 2.5kPa
Min. Supply Pressure
5.5"w.c. / 1.4kPa
11.0"w.c. / 2.8kPa
Max. Supply Pressure
10.0"w.c. / 2.5kPa
13.0"w.c. / 3.3kPa
EFFICIENCY NG / LP
NATURAL GAS
PROPANE
Maximum Observed Steady State Efficiency - %
78.8
79.5
Steady State Efficiency - %
65.0
61.4
Annual Fuel Utilization Efficiency (AFUE) - %
64.2
60.5
Canadian p.4 Efficiency - %
55.1
50.0
NOTE: The maximum achievable steady state efficiency can vary depending on how
the fireplace is installed and operated.
• It is recommended that the pilot flame be turned off if the appliance will not be in use for an extended
period of time.
• This appliance is equipped for use with the fuel type indicated on the rating plate. Field conversion is only
permitted with a conversion kit supplied by SÓLAS.
This appliance has been certified by PFS TECO to ANSI Z21.88-2016/CSA 2.33-2016 Vented Gas
Fireplace Heaters and CSA-2.17-2017, Gas-Fired Appliances for Use At High Altitudes and CSA P.4.1-09.
The is approved for installation at elevations up to 2000 feet in the U.S. and 1370 meters (4500 feet) in
Canada without change. If your installation is at an elevation greater than these, consult with the local
authority having jurisdiction for gas product installations to determine their specific requirements for
high altitude installations.
solasfires.com
9
SPECIFICATIONS
K
L
G
J
A
D
E
H
F
10
C
B
Dimension
Dimension Description
SLIM TWENTY6
A (Min)
Minimum Fireplace Cavity Height
66" (1676mm)
A (Max)
Maximum Fireplace Cavity Height
132" (3353mm)
B
Fireplace Cavity Width
37 19/32" (950mm)
C
Fireplace Cavity Depth
11 9/64" (283mm)
D
Glass Viewing Area Width
31 9/16" (802mm)
E
Glass Viewing Area Height
16 1/32" (407mm)
F
LH Side to Center of Viewing Area
18 5/8" (473mm)
G (Min)
Minimum Steel Stud Length
30" (762mm)
G (Max)
Maximum Steel Stud Length
96" (2438mm)
H
Floor to Centerline of Viewing Area
15 3/16" (386mm)
J (Min)
Minimum Centerline of Viewing Area to Centerline
of Cool Zone Plenum Outlet
49 5/8" (1260mm)
J (Max)
Maximum Centerline of Viewing Area to Centerline
of Cool Zone Plenum Outlet
115 5/8" (2936mm)
K
Cool Zone Plenum Outlet Width
30 3/16" (767mm)
L
Cool Zone Plenum Outlet Height
2 5/8" (66mm)
S Ó L AS CO NTE MPO R ARY F IR E
SPECIFICATIONS
COOL ZONE KIT CONTENTS
FIREPLACE MODEL #
TWENTY6
SINGLE-SIDED
BUILT-IN
KIT PART #
ITEM DESCRIPTION
BI-26-SS
TWENTY6 PLENUM
COOL ZONE 5" FLEX PIPE*
COOL ZONE 5" HOSE CLAMP
TWENTY6 PLENUM OUTLET TRIM
ITEM PART #
ITEM QTY PER KIT
12748
FLX-5-25
12666
13406
1
1
6
1
*The 5” Flex pipe required for this installation can be purchased from SOLAS or from a third-party supplier.
Should you choose to purchase from a third-party supplier, the 5” flex used must be 2-ply thick 3003
Aluminum liner.
PLENUM
OUTLET TRIM
PLENUM
2X4 STEEL STUDS ARE
NOT INCLUDED WITH
COOL-ZONE KIT
5" FLEX PIPE
VIEWING AREA TRIM
For Replacement Parts and Customer Service,
contact your SÓLAS Dealer or;
SÓLAS, LLC 452 Sunapee Street, Newport, NH 03773
P (603) 298-5169 [email protected]
solasfires.com
11
CLEARANCE TO COMBUSTIBLES
A
C
B
Dimension
Dimension Description
SLIM TWENTY6
A (Min)
Minimum Fireplace Cavity Height
66” (1676mm)
A (Max)
Maximum Fireplace Cavity Height
132” (3353mm)
B
Fireplace Cavity Width
37 19/32” (950mm)
C
Fireplace Cavity Depth
11 9/64” (283 mm)
• 1.50” (38mm) clearance to combustibles is required
around the outer diameter of the flue pipe.
• The floor the fireplace immediately rests on must
be constructed of non-combustible material with an
R factor of at least .37, with a minimum thickness of
½” (13mm).
12
• This framing guide is just an example of the many ways
in which a SÓLAS Fireplace can be installed. You may
need to customize this framing design to allow for
things such as doors, windows, countertops, structural
frame members or local code requirements.
• The sheet metal face of this fireplace must be covered
by a finishing material, it may not be left exposed.
Combustible finishing materials are permitted.
S Ó L AS CO NTE MPO R ARY F IR E
CLEARANCE TO COMBUSTIBLES
3.00 (76mm)
MINIMUM CLEARANCE
TO CEILING
COMBUSTIBLE
MANTEL
12.00 (305mm)
MAXIMUM
3.00 (78mm)
MINIMUM
6.00 (152mm)
MINIMUM FROM
BOTH WALLS
WARNING
Follow these instructions carefully to ensure safe
installation. Failure to follow instructions exactly can
create a fire hazard.
• The combustible area above the viewing area must not
protrude more than ¾ (19mm) from the facing; if it does,
it is considered a mantel and must meet the mantel
requirements above.
ATTENTION:
Before proceeding with your installation, determine
if you plan to use either the Power Vent kit (PV800HZ) or the Heat Redistribution Kit (HRD-750).
Read the manual for these optional components
before proceeding with your installation, as your
installation requirements and procedure may
change.
solasfires.com
13
FINISHING INFORMATION & PLANNING
NOTE: SÓLAS can only offer guidance as to the type of
materials that can be safely used during the installation
of your fireplace and cannot comment on, or be
responsible for, any finishing material’s propensity for
fading, flaking, discoloring, cracking, or chipping due to
improper installation and/or thermal expansion. Be sure
to consider a material’s propensity to “off-gas” when hot
as this may cause discomfort for the end user.
NOTE: For a Minimal “Clean” look, we recommend using
materials that have been tested for specific high heat
applications and are designed not to crack or chip such
as Promat and Skamol products. Any other materials
used to achieve this same look might not perform as
intended and are likely to discolor, crack and/or chip.
FINISHING SUGGESTIONS:
Additional tips to help avoid cracking;
Standard gypsum board may be used beyond the perimeter
of the non-combustible zone however it is preferable not
to change materials to help avoid cracking. Ensure that all
compound, mortar, and/or silicone adhesives are rated for
high-temperature applications and have fully cured before
using the fireplace to help reduce the possibility of cracking
as a result of thermal expansion.
• Allow materials to dry thoroughly before finishing the wall.
•T
ile and Stone Veneer Products:
Install a minimum of ½" non-combustible cement board
then apply tile or stone with mortar following instructions
from the finishing material company. Pre-drill cement
board with oversized holes and do not over-tighten
screws to avoid cracking due to thermal expansion.
• Natural Stone, Marble or Granite Type Products:
Install a minimum of ½" non-combustible cement board
then apply tile or stone with mortar following instructions
from the finishing material company. Pre-drill cement
board with oversized holes and do not over-tighten
screws to avoid cracking due to thermal expansion.
• Always pre-drill cement board with oversized holes and
use screws with self-milling head.
• Always use tape over joints.
• Double up studs or use studs “on the flat” to add extra
support to the joint. Help control differential movement by
applying adhesive on the backside of the wall board joints.
• Use multiple, thinner coats of joint compound and allow to
completely dry between coats.
• Ensure all framing materials are dry.
• Introduce heat gradually after finishing the wall to slowly
dry any excess moisture.
• Avoid notching tiles or cement board around corners of
window opening and instead provide a joint that intersects
the corner.
• Take guidance from your authorized fireplace dealer and
experienced installer.
Consult installation and operating instructions supplied
with your SÓLAS fireplace for complete instructions for the
installation and operation of the appliance.
NOTE: Prior to enclosing the wall cavity, test fire the fireplace to ensure it is fully operational.
14
S Ó L AS CO NTE MPO R ARY F IR E
FINISHING INFORMATION & PLANNING
WARNING
Read all instructions completely and thoroughly
before attempting installation. Failure to do so
could result in serious injury, property damage, or
loss of life. Operation of improperly installed or
maintained venting system could result in serious
injury, property damage, or loss of life.
The following actions will void the warranty on your
fireplace:
• Installation and service by non-qualified or
unlicensed technician.
• Installation of any damaged venting component.
• Unauthorized modification of the appliance.
• Unauthorized modification of the venting system.
NOTE:
Any electrical wiring, gas plumbing, or vent
installation required by the appliance must be
done prior to final finishing. The unit shall be test
burned on high for at least 30 minutes prior to
final finishing to confirm proper operation. Failure
to test the appliance before final finishing may
require significant and costly reconstruction.
INSTALLATION PRECAUTIONS
Consult local building codes before beginning the
installation. The installer must make sure to select the
proper vent system for installation. Before installing
the vent kit, the installer must read this fireplace
manual and vent kit instructions. Only a qualified,
licensed, installer/service technician shall install
the venting system. The installer must follow the
following safety rules:
• Installation of any component part not manufactured
or approved by SÓLAS Contemporary Fires.
• Installation other than permitted by these
instructions.
NOTICE
Failure to follow these instructions will void the
warranty.
WARNING: Unauthorized modifications of this
appliance may result in property damage, injury
or loss of life.
• Wear gloves and safety glasses for protection.
• Use extreme caution when using ladders or when
on rooftops.
• Be aware of electrical wiring locations in walls and
ceilings.
solasfires.com
15
INSTALLATION INFORMATION
ELECTRICAL AND PLUMBING
The electrical and plumbing access panel is located on the
right side of the unit.
1. Remove the (3) #10 sheet metal screws using a 5/16" nut driver
that hold the utility access panel to the fireplace.
2. Remove the utility access panel from the fireplace exposing
the junction box and gas line.
3. Remove 3 prong plug(s) from the junction box outlets
attached to the utility access panel.
4. Have a licensed electrician hardwire the junction box
provided in accordance with local codes. The electrical
supply required is 120v, 2.5 amps.
• It is recommended this fireplace be installed
on its own electrical circuit.
• Strain reliefs are required on electrical connections
entering the junction box.
24.1 (611mm)
5. Reinstall 3 prong plug(s) in junction box outlets.
6. Have a licensed plumber connect gas piping to the 3/8"
female flare connection provided in accordance with local
codes. Be sure to check for gas leaks.
7. Reinstall utility access panel with the (3) #10 sheet metal
screws using a 5/16" nut driver.
16
OPTIONAL UTILITY
ACCESS PANEL
LOCATION
UTILITY ACCESS PANEL
S Ó L AS CO NTE MPO R ARY F IR E
OPTIONAL UTILITY
ACCESS PANEL
LOCATION
INSTALLATION INFORMATION
COMFORT BLOWER
Your SÓLAS fireplace is equipped with a Comfort
Blower to help efficiently move heat into your living
space.
The Comfort Blower has 4 speed levels controlled
by the SÓLAS One-Touch remote. See bottom right
column of page 36 for details on remote operation.
In the event of a power outage, your fireplace will
continue to operate, but the Comfort Blower will not
function. Once power is restored you can use the
Comfort Blower.
We recommend using your Comfort Blower on speed
1 or 2 which will help move a sufficient amount of
warm air from your fireplace into your heating zone
while remaining quiet. With the increased air speed
of levels 3 and 4, there will be a noticeable difference
in sound.
We recommend during the annual service on your
fireplace Comfort Blower, use a vacuum and/or
compressed air to remove any dust, pet hair etc.
When servicing your fireplace, first shut off power
to it.
The Comfort Blower is located to the left of the
gas valve located under the air screen assembly.
(as shown in image below). To gain access to the
Comfort Blower please see page 26 first for
Screen Removal.
In the event your Comfort Blower needs replacing, a
licensed service technician can remove the Comfort
Blower by removing the (2) 1/4-20 nuts with a 7/16"
driver, located on each side of the Comfort Blower
as shown in the image below.
1/4-20
Nut
1/4-20 Nut
solasfires.com
17
VENTING
The SÓLAS TWENTY6 Slim-Line Built-In Gas
Fireplace has been tested and listed for installation
with 4” X 6 5/8” Simpson DuraVent GS/Pro®, Selkirk
Direct-Temp®, Security Secure Vent™, AmeriVent
Direct™, Metal Fab DirectVent and ICC EXCELDirect
venting components. Although you may use the
pipe components (straight pipe, elbows, etc.) from
any of the listed manufacturers, you may only use
the vent terminations (caps) listed in the chart on
page 19. For installations where a snorkel is needed,
please note that only three snorkels are approved
for use. Please plan your installation accordingly.
For all specific venting installation requirements,
follow the installation instructions included by the
venting manufacturer with the venting system
components you have chosen.
Please Note:
• For venting configurations that include no vertical
rise, a total horizontal equivalent vent run of up to
30 inches is allowed (when using a 45° elbow, 18
inches horizontal equivalent must be included).
However, if your installation has room to add a
vertical pipe section, we suggest adding at least
one foot of vertical rise to the system.
• For venting configurations that include vertical
rise, it is assumed that the installation will include
at least one 90° elbow. Up to three additional 90°
elbows (or equivalent 45° elbows) may also be
used. The total venting may not exceed 20 feet of
vertical rise and/or 10 feet horizontal run. Refer to
the venting charts starting on pages 20 & 21 for
specific details while you plan your installation.
Note: The number of elbows impacts the
maximum allowable horizontal vent run.
•Many installations will involve venting directly
through standard 2 X 4 or 2 X 6 construction
exterior wall to a horizontal vent termination
(cap). The vent starter pipe has been designed
to accommodate those two common installations
without the use of any additional venting
components other than a standard horizontal cap.
See the chart on page 19 for a list of approved vent
caps.
18
• If the fireplace will be installed on an interior wall
or other location that precludes venting directly
through an outside wall to a horizontal vent cap, or
if the distance to the outside wall exceeds 30", one
or more elbows will be required to allow addition
of the required vertical venting to the installation.
When vertical venting is required, the fireplace
venting may be terminated with either a vertical or
horizontal vent cap depending on the specifics of
the installation. Refer to the venting charts starting
on pages 20 & 21 for specific venting requirements
and see the chart on page 19 for a list of approved
vent caps before you plan your installation.
• There should be a 1 1/2" overlap of the vent and
combustion air tubes, when telescopic joints are
used.
• A minimum clear space of 1 1/2" must be maintained
around the vent pipe where it penetrates the first
combustible wall adjacent to the fireplace (either
the outside wall for the direct-through-the-wall
installation or the partition wall for the 45° or other
interior wall installations). The special vent pipe
heat shields that are provided with the TWENTY6
must also be installed in the first wall adjacent to
the fire-place. A minimum clear space of 1 1/2" must
also be maintained where the vent pipe penetrates
any other interior wall, exterior wall, ceiling or roof.
• The TWENTY6 Slim-Line Built-In may also be
installed in front of an existing fireplace opening
utilizing special co-linear venting components
available from the venting manufacturers. These
systems split and then recombine the co-axial air
and exhaust and allow the use of flexible venting.
This makes it easier to run the venting through
the narrow fireplace damper opening to the top
of the chimney. Refer to the vent manufacturers’
instructions. Use the vertical venting column (0 feet
Horizontal Run) in the venting charts to determine
the required restrictor settings depending on the
height of chimney.
S Ó L AS CO NTE MPO R ARY F IR E
USING THE VENTING CHARTS
The location of the vent termination must meet the requirements of the current edition of ANSI Z223.1/NFPA 54,
National Fuel Gas Code or CAN B419.1, Natural Gas and Propane Installation Code and the requirements shown on
page 25 of this manual.
APPROVED VENT
TERMINATIONS
M&G DURAVENT
GS/PRO
SELKIRK
DIRECT- TEMP
SECURITY
SECURE VENT
AMERIVENT
DIRECT VENT
METAL FAB
DIRECT VENT
ICC EXCEL
DIRECT
VERTICAL CAP
46DVAVCH
1604802
SV4CGC
4DVC
4DVT
TM4VT
HORIZONTAL CAP
46DVAHC
46DVAHRCS
46DVAHSC
1604804
SV4GHC
4DHC
4DHT
TM4HT
TM4DHT
SNORKEL
N/A
1604836
N/A
4D36C
N/A
TMST36
Just as with any other vented device, vertical vent rise
creates draft (negative pressure) in the firebox as the
exhaust gases heat up. If this draft becomes excessive, it
can affect the performance or appearance of the fire. The
TWENTY6 fireplace includes air and exhaust restrictors
that are used to balance the draft in the fireplace to the
optimal level for installations where excessive draft might
occur. The venting charts on pages 20 and 21 provide
an easy means for determining whether your specific
installation requires inlet air or exhaust restrictors or both.
To make the determination about whether air or exhaust
restrictors are needed, a venting chart worksheet is
provided on page 22. Follow the instructions and fill in the
worksheet for your particular installation. This will allow
you to determine the recommended restrictor settings
for your exact installation. Although this might appear to
be a complicated process at first glance, it is really quite
straight-forward and the result will be a fire that looks and
performs as intended. Several examples of worksheet
calculations are shown on page 23 to help guide you.
Please be sure to note that:
1. There are separate venting charts for Natural Gas and
LP Gas. Refer to the appropriate chart for your fuel type
to determine your specific restrictor requirements. The
settings in the charts have been deter-mined based on
extensive testing.
5. The recommended restrictor settings in the venting
charts allow up to two 90° elbows (or 45° elbow
equivalents) to be used without affecting the restrictor
settings. Additional elbows will require that you
calculate a new equivalent horizontal run for your
installation to account for the additional flow resistance caused by the extra elbows. For the purposes
of calculating the equivalent horizontal vent run, each
additional 90° elbow is equivalent to three feet of
horizontal vent run and each additional 45° elbow is
equivalent to 1.5 feet of horizontal vent run. The total
horizontal vent run including elbow equivalents can
not exceed 10 feet.
6. The maximum vertical vent rise can not exceed 20 feet.
7. There are two exhaust restrictors that are provided
with your fireplace. They are labeled “A” and “B”. The A
restrictor provides less exhaust restriction than B.
8. An air restrictor plate is also provided with your
fireplace. It is a ring with bendable tabs that can be
set to adjust the amount of restriction in the air supply
system. Once the appropriate number tabs are bent
open (in accordance with the requirements for your
installation), the plate is inserted between the fireplace
and the vent starter pipe.
2. Determine the total vertical vent rise and total
horizontal vent run for your installation. All measurements are made from the center of the vent opening in
the back of the fireplace.
SÓLAS Self-Calibrating Power Vent Option
Available for all SÓLAS Wall-Mount DV Models
Learn more @ solasfires.com
3. If your fireplace will not be venting directly though an
outside wall to a horizontal termination or if more than
30" of horizontal vent run is required, some vertical
vent rise will be required for the fireplace to function
and vent properly. Elbows will also be required for
those installations. However, installations are limited
to a maximum of four 90° elbows (or 45° elbow
equivalents).
4. Note: Two 45° elbows equal one 90° elbow.
solasfires.com
19
NATURAL GAS VENT CHART
VERTICAL VENT RUN (FEET)
KEY:
NA
B
= NOT USED
AIR RESTRICTOR 1/2 - 3 Tabs Open
= POWER VENT
15
16
17
18
19
20
A
A
B
B
B
B
B
4
4
4
NU
NU
NU
NU
NU
A
A
A
A
B
B
B
B
B
4
4
4
4
4
NU
NU
NU
NU
NU
A
A
A
A
A
A
B
B
B
B
B
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
B
B
B
B
B
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
NU
NU
NU
NU
A
A
A
A
A
A
A
A
A
A
A
B
B
B
B
B
NU
NU
NU
NU
NU
4
4
4
4
4
4
4
4
4
4
NU
NU
NU
NU
NU
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
2
PV
14
A
4
A
4
A
4
A
4
A
NU
NU
NU
NU
NA
NU
EXHAUST RESTRICTOR “A” or “B”
= NOT ALLOWED
13
A
4
A
4
A
4
A
NU
NU
NU
NU
NU
NA
10
12
A
4
A
4
A
4
A
NU
NU
NU
NU
NA
9
11
A
NA
A
4
A
NU
NU
NU
NU
NU
NA
8
10
NA
NA
A
4
A
NU
NU
NU
NU
NA
7
9
NA
NA
A
NU
NU
NU
NU
NU
NA
6
8
NA
NA
A
NU
NU
NU
NU
NA
5
7
NA
NA
NU
NU
NU
NU
NA
4
6
NA
NA
NU
NU
NU
NA
3
5
NA
NA
NU
NU
NA
2 1/2
4
NA
NA
NU
NA
2
3
NA
NA
NA
1
2
NA
NA
0
1
NA
10
NA
9
NA
8
NU
7
NU
6
NU
5
NU
4
NU
3
NU
2 1/2
NU
2
NU
1
0
0
S Ó L AS CO NTE MPO R ARY F IR E
20
HORIZONTAL VENT RUN (FEET)
Power vent runs of up to 130ft with (8) 90⁰ elbows are permitted when using
the SOLAS Self-Calibrating Power Vent Kit. Refer to power vent instructions for
additional power vent installation and operation information.
VERTICAL VENT RUN (FEET)
NA
NA
NA
NA
NA
NA
NA
NA
NA
NU
8
7
6
5
4
3
2
1
0
B
13
9
B
14
B
B
15
10
B
16
B
B
17
11
B
18
B
B
19
12
B
20
NA
KEY:
0
0
solasfires.com
NU
NA
NA
NA
NA
NA
NA
NA
NA
NA
1
1
1
1
1
2
2
2
3
3
3
NU
NU
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
1
1
= NOT ALLOWED
NU
NU
NU
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NU
NU
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
2
2
NU
NU
NU
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NU
B
2 1/2
NU
NU
NU
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
2
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
4
4
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
5
5
HORIZONTAL VENT RUN (FEET)
3
3
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
AIR RESTRICTOR 1/2 - 3 Tabs Open
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
6
6
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
7
7
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
8
8
PV
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
9
NA
NU
3 1/2
3 1/2
9
= POWER VENT
Power vent runs of up to 130ft with (8) 90⁰ elbows are permitted when using
the SOLAS Self-Calibrating Power Vent Kit. Refer to power vent instructions for
additional power vent installation and operation information.
NU
NU
A
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
2 1/2
= NOT USED
EXHAUST RESTRICTOR “A” or “B”
NA
NU
NU
A
A
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
B
10
10
NA
NU
3 1/2
3 1/2
4
4
5
5
5
5
5
4
4
4
2
2
2
2
3
3
3
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
LP GAS VENT CHART
VERTICAL VENT RUN (FEET)
VERTICAL VENT RUN (FEET)
21
VENTING CHART WORKSHEET
VENTING WORKSHEET FOR INSTALLER
Use this worksheet to determine the equivalent horizontal run for use with the vent charts on pages 23 and 24. The
information contained within this worksheet may also be useful during installation or in the event that you need technical
assistance from SÓLAS.
NOTE: Calculations for horizontal or vertical sections of pipe are measured between transition joints as shown
in the image below.
Vent runs that are not 90° vertical are considered to have horizontal run but not a vertical rise.
NOTE: Snorkel terminations are counted as (2) 90° elbows.
A. TOTAL VERTICAL VENT RISE: Measured as total vertical distance between flanges of elbows used in vent
system. (See Diagram) _____________ Feet
B. T
OTAL HORIZONTAL VENT RUN: Measured as total horizontal distance between flanges of elbows used in vent
system. (See Diagram) _____________ Feet
C. T
OTAL NUMBER OF 90° ELBOWS in excess of 1: _______ = "C"
NOTE: Snorkel terminations are counted as (2) 90° elbows
D. TOTAL NUMBER OF 45° ELBOWS in excess of 1: _______ = "D"
E. 90⁰ Elbow Horizontal Equivalent: C x 3 = _________
F. 45⁰ Elbows Horizontal Equivalent: D x 1.5 = _________
G. Total Horizontal Equivalent: B + E + F = _________
Horizontal or vertical sections of pipe are measured between transition joints as shown in this image.
NOTE: Prior to enclosing the wall cavity, test fire the fireplace to ensure it is fully operational.
22
S Ó L AS CO NTE MPO R ARY F IR E
VENTING CHART WORK SHEET EXAMPLES
Side View
EXAMPLE 1 – TWENTY6 Slim-Line Built-In
A. Total Vertical Vent Rise:
B. Total Horizontal Vent Run:
5 ft
1
__________
feet
5
__________
feet
1
C. Total Number of 90° Elbows in excess of 1:. __________
(Snorkel terminations are counted as (2) 90° elbows)
1 ft
0
D. Total Number of 45° Elbows in excess of 1:. __________
3
E. 90⁰ Elbow Horizontal Equivalent: C x 3 = _____
0
F. 45⁰ Elbow Horizontal Equivalent: D x 1.5 = _____
8
G. Total Horizontal Equivalent: B + E + F = _____
Side View
EXAMPLE 2 – TWENTY6 Slim-Line Built-In
A. Total Vertical Vent Rise:
B. Total Horizontal Vent Run:
0
__________
feet
2
__________
feet
0
C. Total Number of 90° Elbows in excess of 1: .__________
(Snorkel terminations are counted as (2) 90° elbows)
0
D. Total Number of 45° Elbows in excess of 1:.__________
2 ft
0
E. 90⁰ Elbow Horizontal Equivalent: C x 3 = _____
0
F. 45⁰ Elbow Horizontal Equivalent: D x 1.5 = _____
2
G. Total Horizontal Equivalent: B + E + F = _____
Side View
EXAMPLE 3 – TWENTY6 Slim-Line Built-In
A. Total Vertical Vent Rise:
B. Total Horizontal Vent Run:
0
__________
feet
4
__________
feet
1
C. Total Number of 90° Elbows in excess of 1: .__________
(Snorkel terminations are counted as (2) 90° elbows)
4 ft
0
D. Total Number of 45° Elbows in excess of 1: .__________
3
E. 90⁰ Elbow Horizontal Equivalent: C x 3 = _____
This vent configuration is NOT
ALLOWED. Refer to Vent Chart
on pages 20 and 21.
0
F. 45⁰ Elbow Horizontal Equivalent: D x 1.5 = _____
7
G. Total Horizontal Equivalent: B + E + F = _____
solasfires.com
23
VENTING
The illustration below shows some of the many ways the TWENTY6 fireplace may be installed in the home. This
includes interior and exterior wall installations, corner installations and horizontal and vertical vent terminations.
Horizontal
Termination
Vertical
Termination
Power vent runs of up to 130ft with (8) 90⁰ elbows are permitted when using
the SOLAS Self-Calibrating Power Vent Kit. Refer to power vent instructions for
additional power vent installation and operation information.
24
S Ó L AS CO NTE MPO R ARY F IR E
VENTING
2’
S
H
2’
2’
Covered
Alcove Detail
Vinyl Siding
2’
29.5’’
17.5’’
S
17’’
11.5’’
R
Must use Vinyl Siding
Termination Shield
P
I
E
N
F
L
D
M
Covered
Alcove Detail
U
D
G
V
K
D
J
VENT TERMINAL LOCATIONS
CANADA*
U.S.A.**
A = Clearance to the termination frame above grade, veranda, porch, deck, or balcony 12" (30 cm)
12" (30 cm)
B = Clearance to top of doors or operable windows
12" (30 cm)
12" (30 cm)
C = Clearance to sides or bottom of door or operable windows
12" (30 cm)
9" (23 cm)
D = Clearance to permanently closed window, recommended to prevent condensation
16" (41 cm)
16" (41 cm)
E = Clearance to ventilated soffit located within a horizontal distance to 24" (61 cm)
from centerline of termination
22" (56 cm)
22" (56 cm)
F = Clearance to unventilated soffit
30" (76 cm) to combustibles
16" (41 cm) to non-combustible
30" (76 cm) to combustibles
16" (41 cm) to non-combustible
G = Clearance to outside corner
9" (23 cm)
9" (23 cm)
H = Clearance to inside corner
12" (30 cm)
12" (30 cm)
I = Clearance to each side of the vertical centerline of a meter or regulatory assembly
to a maximum vertical distance of 15ft (4.5m)
36" (91 cm)
36" (91 cm)
J = Clearance to service regulator vent outlet
36" (91 cm)
36" (91 cm)
K = Clearance to non-mechanical air supply inlet to the building or combustion air
inlet to other appliance for appliance <=100.000 BTU/H (30 KW)
12" (30 cm)
12" (30 cm)
L = Clearance to forced air supply inlet
72" (183 cm)
36" (91 cm) above air inlet
M = Clearance above paved sidewalk or paved driveway located on public property
84" (213 cm)
84" (213 cm)
N = Clearance under veranda, porch, deck, or balcony
22" to combustibles
16" to non-combustibles
22" to combustibles
16" to non-combustibles
P = Clearance above roof
24" (61 cm)
24" (61 cm)
Q = Clearance to adjacent walls and neighboring buildings
24" (61 cm)
18" (46 cm)
R = Clearance from corner in recessed location
12" (30 cm)
12" (30 cm)
S = Maximum depth of recessed location
48" (122 cm)
48" (122 cm)
T = Maximum width for back wall of recessed location
24" (61 cm)
24" (61 cm)
U = Horizontal clearance between two terminations that are level
0
0
V = Horizontal clearance (center to center) between two terminations that are not level
18" (46 cm)
18" (46 cm)
Note 1: For N a vent shall not terminate directly above the sidewalk or paved driveway which is located between two single-family dwellings and serve both dwellings.
Note 2: For P only permitted if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor.
Note 3: For J, K, and as specified in CGA B149 installation co de. Local codes or regulations may vary.
* Based on CGA B149.1 Natural Gas and Propane installation code. Local codes may vary, please check with local regulatory agency.
** Based on ANSI Z223.1/NFPA 54 National Fuel Gas Code. Local codes may vary, please check with local regulatory agency.
NOTICE: Venting terminations shall not be recessed into a wall or siding.
solasfires.com
25
STARTER PIPE INSTALLATION
UNPACKING THE TWENTY6 SLIM-LINE BUILT-IN
FIREPLACE
The fireplace is shipped on a pallet. The venting
components are in one carton. Start with the carton that
contains the vent starter pipe, vent heat shields and air
and exhaust restrictors.
3. Using a 5/16” nut driver, remove the 6x #10 sheet metal
screws from the firebox heat shield access panel.
1. Before beginning, locate the TWENTY6 Slim-Line
Built-In Vent Adapter kit.
Box Contents
Inner
Heat Shield
Outer
Heat Shield
Starter
Pipe
Gasket
Restrictors
2. Using a 5/16” nut driver, remove the 8x #10 sheet metal
screws from the outer can vent access panel.
4. At this point, it is necessary to determine whether your
installation will require the addition of flow restrictors
for the combustion air inlet system, the exhaust
outlet, or both. Refer to the applicable vent chart
for your gas type and vent configuration on pages
20 & 21, if an air restrictor is required for your vent
configuration, prepare the air restrictor now. Identify on
the appropriate vent chart the number of tabs to open
on the air restrictor and do so now by breaking and
discarding these tabs.
5. Place the vent starter gasket on the back of the firebox,
it may be helpful to apply 3 or 4 very small dabs of high
temperature (500F) silicone (RTV) to hold the gasket in
place while continuing with the installation.
26
S Ó L AS CO NTE MPO R ARY F IR E
STARTER PIPE INSTALLATION
6. The exhaust restrictor is installed by placing it through
the exhaust outlet pipe and resting it on the internal
baffle in the firebox. It is held in place with a movable
retainer clip. Simply hold the restrictor down against
the baffle and push the retainer up and tighten screw
to secure the restrictor. Note: Please take care to
ensure that the exhaust restrictor is centered in the
exhaust outlet. Improper alignment could adversely
affect the appearance of the flames. Refer to the
adjacent images for placement of the exhaust
restrictor.
7. Place the Air restrictor between the gasket and the vent
starter pipe. Using a 5/16” nut driver, secure the vent
starter pipe using 4x #10 sheet metal screws provided.
8. Locate the firebox heat shield access panel removed
during step #3 on page 25. To install the inner heat
shield, align the three tabs with the 3 pilot holes in the
firebox heat shield access panel. Using a 5/16” nut driver,
secure the inner heat shield using 3x #10 sheet metal
screws provided. (add picture)
solasfires.com
27
STARTER PIPE INSTALLATION
9. Install the outer heat shield, align the three tabs with
the 3 pilot holes in the firebox heat shield access
panel. Using a 5/16” nut driver, secure the outer heat
shield using 3x #10 sheet metal screws provided.
10. Using a 5/16” nut driver, reinstall the outer can vent
access panel using the 8x #10 sheet metal screws
saved from step #2 on page 26.
The Starter pipe and required telescoping heat shields
are now installed, the unit is ready for the next step of
the installation.
ATTENTION
Once the unit is installed, test burn the fireplace
for at least 30 minutes to confirm that the unit is
performing as expected before enclosing the unit
within the wall while the vent pipe is still accessible.
Failure to test burn the fireplace may result in costly
repairs not covered by the manufacturer’s warranty.
28
S Ó L AS CO NTE MPO R ARY F IR E
INSTALLATION
DETAIL A
A
12. Place the unit in position within the combustible
framing shown on page 12. The 2x4 steel studs (not
included) will be installed next. The stud length,
dimensions “G” on page 10 can be calculated using
either of the following equations:
13. O
nce the studs have been cut to length, insert the
studs fully in the collector stud brackets as shown in
“Detail A” above, secure with (4) #10 self-drilling sheet
metal screws per stud.
Stud Length Equation:
English (inches): Stud Length G = A – 31.375"
Metric (millimeters): Stud Length G = A – 797mm
*Refer to page 10 for Dimension “G” referenced
in the above equations.
solasfires.com
29
INSTALLATION
14. The 5” diameter flex duct will now be installed. The
duct length can be calculated using either of the
following equations:
15. O
nce the duct length has been calculated, stretch the
ducts to the length calculated in step #5 and secure to
the collector using the 5” hose clamps provided.
Duct Length Equation:
English (inches): Duct Length = G – 23.75"
Metric (millimeters): Duct Length = G – 603mm
*Refer to step 3 for Dimension “G” referenced
in the above equations.
30
S Ó L AS CO NTE MPO R ARY F IR E
INSTALLATION
B
DETAIL B
16. Install the plenum as shown below, the front studs
will be inserted into the plenum stud brackets until
they make contact with the plenum (as shown in
“Detail B”). Secure the front studs to the plenum
stud brackets using the (4) #10 self-drilling sheet
metal screws per stud provided.
18. Once the plenum has been installed, connect the
ducts to the plenum and secure to the collector
using the 5” hose clamps provided.
17. Once the front studs have been secured to the
plenum, confirm that the plenum is level front to
back and side to side. Once the plenum is level,
secure the rear studs to the plenum stud brackets
using the (4) #10 self-drilling sheet metal screws per
stud provided.
19. Once the unit has been enclosed within the wall
the “Plenum Outlet Trim” will be press fit into
the plenum outlet opening. Apply some high
temperature RTV/silicone during the installation of
the “Plenum Outlet Trim” to insure it is secured in
place.
solasfires.com
31
INSTALLATION
Installing the Outer Vent Heat Shields and Vent
Termination (Parallel Installation on Outside Wall)
20. Before you install the horizontal vent termination,
you must first install the second halves of the two
telescoping vent pipe heat shields. Each shield half
simply slips over the half you previously attached to
the fireplace mounting plate and can now be seen
inside the vent pass-through in the wall.
24. Slide the vent termination (cap) into the siding recess
(or vinyl siding shield) until it bottoms out. Note: The
rear surface of the vent termination will push the
telescoping vent pipe heat shields inward. When the
vent termination is in place the heat shields will just
touch the rear surface of the termination.
21. Install the outer shield first and the inner second.
Leave about 2” of the shields protruding past the
house sheathing.
22. Install the horizontal vent termination (vent cap). Be
sure the arrow on the cap (if present) is pointing
up and reconfirm that all the vent cap location
requirements per pages 24-25 and the vent
manufacturers requirements are met.
23. Slip the inner and outer vent termination pipes onto
the vent starter pipe taking care to align the inner and
outer pipes to prevent damage.
32
25. Pull the vent cap away from the sheathing and install
a small bead of non-hardening silicone sealer around
the cap perimeter. Push the cap in place.
26. Install the mounting screws (included with the cap) to
hold the vent cap to the sheathing See the venting
manufacturers instructions for the location of the
mounting holes. Typical mounting hole locations
are shown in the adjacent photo. See the venting
manufacturers instructions for more information or if
using the vinyl siding shield.
S Ó L AS CO NTE MPO R ARY F IR E
INSTALLATION
Installing the Outer Vent Heat Shields
(Partition Wall Installation)
1. Before you install the additional vent pipe and elbow(s)
that will complete the venting installation, you must first
install the second sections of the vent pipe heat shields
to protect the combustible materials around the vent
pipe pass-through in the partition wall that the fireplace
is mounted on. Each shield half simply slips over the
half you previously attached to the fireplace mounting
plate and that can now be seen inside the vent passthrough in the partition wall.
2. Install the outer shield first and the inner second. Leave
at least 2" of both shields protruding past the partition
wall framing or wall covering. See the photo to right.
Vent Pipe and Vent Termination Installation
(Partition Wall Installation)
1. The specific details of the vent configuration from the
vent starter pipe on the fireplace to the horizontal
or vertical vent termination (cap) when the fireplace
is installed on an interior wall of the house will vary
depending on the location of the fireplace on the wall,
what is on the back side of the wall, where the vent
termination will be located (roof or exterior wall) and
on other code requirements for the location of the
vent termination as shown pages 24-25. However, the
maximum vent length, measured along the centerline
of the pipe, from the back of the fireplace to the
start of the vent termination cannot exceed 30 feet,
including a maximum of 20 feet of vertical rise and a
maximum of 10 feet of horizontal run. If more than two
90° elbows (or equivalent 45° elbows) are needed for
your installation, the maximum amount of horizontal run
allowed is reduced. See the venting section starting on
page 18 for specific information. It is important to plan
the installation in advance so that you can accurately
locate any wall or ceiling pass-throughs and the vent
termination on the exterior of the wall or roof. The vent
pipe sections are available only in certain increments of
length and in adjustable length sections. Plan carefully
before you start!
3. Be sure that the two vent pipe heat shields extend
at least 2" beyond the rear side of the partition wall
adjacent to the fireplace after the venting is installed.
4. Maintain a minimum 1 1/2" unobstructed air space
around the vent pipe where it passes through other
interior walls, the ceiling, the exterior wall or the roof.
5. N
ote: Vent manufacturer’s instructions and some
building codes may require the addition of blocking
above and below all wall pass-throughs, the addition
of vent manufacturer supplied fire-stops, wall thimbles,
attic insulation shields, interior trim collars, vent support
brackets, or other components. Please check with the
authority having jurisdiction in your area when planning
the venting installation to determine the specific code
requirements and exact venting components that are
required for your installation.
2. You will find it helpful to leave access to the area
behind the partition wall to facilitate installation of the
vent components. The pipe sections may have twist
lock connections which will be difficult to execute
without good access.
solasfires.com
33
INSTALLATION
PLACING THE BURNER GLASS MEDIA
The burner glass media poly-bag that you set aside
when you unpacked the fireplace contains the correct
amount of glass material to cover the burner. DO NOT
add any additional media to the media supplied with your
fireplace. The entire contents of the bag should be evenly
distributed over the burner tray.
1. Locate the burner in the fireplace. Refer to the adjacent
illustration.
2. Carefully clip one corner of the poly-bag to form a
pouring spout. The opening should be large enough to
allow the glass media to flow but not so large that you
can’t control the flow.
3. You will notice that the burner surface is designed
with turned-up edges that form a tray to hold the glass
media.
Burner Tray
4. Starting at one end, pour the glass media onto the
burner tray, keeping the pouring spout on the polybag toward the center of the burner to avoid spillage
of glass pieces over the sides of the burner. See the
adjacent illustrations.
5. Once you have poured all of the glass burner media
into the burner tray, carefully smooth the glass pieces
out so they have a uniform depth over the entire
surface of the burner. When the burner glass media is
properly placed, it should look like the images here on
the right.
Note: If a few pieces of glass escape over the edges of
the burner tray during installation, it is not a problem.
They will simply land in the area below the burner and
will do no harm.
Burner Glass Media – Partially Installed
Optional Birch Log Set Available
Refer to separate Log Set Manual for assembly.
Burner Glass Media – Fully Installed
34
S Ó L AS CO NTE MPO R ARY F IR E
INSTALLATION
Removing the Glass Assembly
1. Use the pull tabs on the air screen to pull it up and out
of the fireplace.
3. The (10) Philips head screws that retain the screen will
now be exposed, using a Philips head screwdriver,
remove these screws.
2. Lift the Left Side Panel up and into the fireplace
opening to remove it. Then lift the Right Side panel up
and into the fireplace opening to remove it.
solasfires.com
35
INSTALLATION
4. Once the (10) Philips screws are removed, lift the
screen up, then tilt the bottom out of the fireplace
to remove.
5. Remove the (4) ¼-20 bolts (see arrows) along the top
of the glass frame using a 7/16” socket.
6. Once the (4) ¼-20 bolts have been removed, lift the
glass frame up, then tilt the bottom out of the fireplace
to remove using the same motion as was used with the
screen.
Reverse these steps to reinstall the glass and screen
assembly.
ATTENTION!
Once the unit is installed, test burn the fireplace for at
least 30 minutes to confirm that the unit is performing
as expected before enclosing the unit within the wall
while the vent pipe is still accessible. Failure to test
burn the fireplace may result in costly repairs not
covered by the manufacturer’s warranty.
(Fireplace enclosure front removed to show glass
frame hardware)
36
S Ó L AS CO NTE MPO R ARY F IR E
LIGHTING & OPERATION
FIRST FIRE INSTRUCTIONS
When operating your new fireplace for the first time, some
vapors may be released due to the curing compounds
used in the manufacture of the appliance. They may cause
a slight odor and could cause the flames to be the full
height of the firebox, or even slightly higher, for the first few
hours of operation. It is possible that these vapors could
set off smoke detection alarms in the immediate vicinity.
These vapors are quite normal on new appliances. We
recommend opening a window to vent the room during the
burn off period. After a few hours use, the vapors will have
disappeared and the flames will be at their normal height.
SERVICING
If any attention is required for your appliance, contact your
dealer quoting the model number and serial number. This
number is on the rating plate, which is located adjacent
to the control module. The replacement parts are shown
at the end of this manual. Please always quote the part
number and description when requesting spare parts.
Warranty is void if serviced by a non-qualified technician.
FIREPLACE CONTROL DEVICES
There are two ways to control your fireplace.
Where applicable, it is important that the blower is turned
on to help clear the vapors from the unit.
1. SÓLAS One-Touch Remote (S-507)
Follow these instructions for a successful first fire;
1. Turn the fireplace on in Manual Mode.
2. Set flame height to HI.
3. Set the blower speed control to level 2.
4.Let the fireplace run for 3 hours at this setting then shut
off fireplace and let it cool.
5.After the fireplace cools, turn the fireplace on in manual
mode with flame on HI and the blower off.
6.Allow fireplace to run for 6 hours in this setting.
The SÓLAS One-Touch Remote can be programmed to
function automatically—see pages 41-46.
2. Optional Wall Touch Pad (WTP-1500)
The Optional Wall Touch Pad can be used to turn the flame
on, off, and to increase or decrease the flame height.
NOTE: The SÓLAS One-Touch Remote in the
AUTO mode will override the Wall Touch Pad.
NOTE: Slight Odors may still be noticed on future uses
of the fireplace but will diminish over time. The type of
finishing materials used around the fireplace may add
odors or add to the curing time. If the fireplace has not
been used in several months, it is normal for odors to
occur caused by lint or dust that has settled on the unit
while not in use.
AM
PM
FLAME SUPERVISION DEVICE
UP
For your safety, this appliance is fitted with a flame
supervision device which will shut-off the gas supply if, for
any reason, the pilot flame goes out. This device incorporates
a fixed probe, which senses the heat from the pilot flame. If
the probe is cool, the device will prevent any gas flow unless
manually lighting the pilot. See full lighting instructions.
ON-OFF
DOWN
NOTE: Periodically conduct a visual check to ensure the
pilot and burner flames are as shown (top of page 38).
During extreme cold weather, it is recommended that you
leave the pilot running to prevent condensation forming in
the firebox and on the glass viewing area during startup.
LIGHTING, OPERATION & RATING INFO
The Lighting, Operation and Rating information is located
on a plate in front of the Comfort Blower inside the front
face of the fireplace.
To access the plate, remove lower air trim panel as shown
in step 1 on page 35.
SÓLAS One-Touch
Remote Part #S-507
Wall Touch Pad
Part #WTP-1500
(Optional)
NOTE: The Wall Touch Pad is not compatible
with the SÓLAS Self-Calibrating Power Vent
System.
solasfires.com
37
LIGHTING & OPERATION
WARNING: If you do not follow these instructions
exactly, a fire or explosion may result causing
property damage, technicianal injury or loss of
life.
Flame
Flame
When lighting this appliance, follow instructions exactly.
A. This appliance is equipped with an ignition device that
automatically lights the pilot. Do not try to light the pilot
by hand.
Pilot Light
B. BEFORE OPERATING THE BURNER SYSTEM, smell
around the appliance area for gas. Be sure to smell next
to the floor because some gas is heavier than air and
will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light the appliance.
Pilot Light Location
• Do not touch any electric switch; do not use any telephone
in your building.
•
Immediately call your gas supplier from a neighbor’s
telephone. Follow the gas supplier’s instructions
•
If you cannot reach your gas supplier, call the fire
department.
C. Use only your hand to operate the gas controls. Never
use tools. If a knob will not push in or turn by hand, don’t
try to repair it, call a qualified service technician. Force
or attempted repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under
water. Immediately call a qualified service technician
to inspect the appliance and to replace any part of the
control system which has been under water.
OPERATING INSTRUCTIONS
1. STOP! Read the safety information above on this label.
2. This appliance is equipped with an ignition device that
automatically lights the pilot. Do not try to light the pilot
by hand.
NOTE: If the pilot does not stay lit after several tries,
proceed to step 9.
7. Use the flame height adjustment buttons on either the
Remote or the optional Wall Touch Pad to adjust the flame.
To increase flame height, press and hold . To decrease
flame height, press and hold .
8. Press and hold the
button on the Remote or optional
Wall Touch Pad to set the appliance to Pilot flame only.
9. If the appliance will not operate, follow the instructions
“TO TURN OFF GAS TO THE APPLIANCE" and call your
gas service technician or gas supplier.
TO TURN OFF GAS TO THE APPLIANCE
1. To turn off gas to the appliance, push and release the
“OFF" button on either the Remote or the optional Wall
Touch Pad. An audible signal will confirm.
2. TO TURN OFF THE GAS SUPPLY TO THE APPLIANCE,
close the shut-off valve on the gas supply line to the
appliance.
3. Confirm that the remote LCD display says “OFF”. Visually
check there is no pilot flame visible inside the fireplace.
AM
PM
4. Wait five (5) minutes to clear out any gas. Then smell for
gas including near the floor. If you smell gas, STOP! Follow
“B" in the safety information above. If you don’t smell gas,
proceed to step 5.
5. Using either the Remote or the optional Wall Touch Pad,
press and hold the “ON/OFF" button for 4 seconds. An
audible signal confirms the start sequence has begun.
HI Flame
ON/OFF
6. Continuing beeps confirm the ignition is in process. Once
lighting the pilot flame should appear as shown below.
Once the pilot is confirmed, the main burner ignites on high.
38
S Ó L AS CO NTE MPO R ARY F IR E
LO Flame
SÓLAS ONE-TOUCH REMOTE OPERATION
SÓLAS ONE-TOUCH REMOTE
PAIRING SET-UP
The Control Module and the Remote must be paired
before the first use. This has been completed for you
at the factory. Refer to the section below if the Control
Module and Remote lose synchronization.
1. Insert two AAA alkaline batteries in the Remote. Only
use brand name alkaline batteries, such as Duracell or
Energizer.
2. Four AA alkaline batteries are installed in the Control
Module (shown below).
3. Locate the RESET button on the front side of the
Control Module.
4. Press and hold the Control Module’s RESET button until
you hear one short beep and one long beep. After the
second beep, release the reset button.
5. Within the subsequent 20 seconds, press and hold
the button on the Remote for 2-3 seconds.
will be displayed and flash on the Remote during the
pairing sequence. The Remote will count up from 1 to
8, and you will hear two short beeps confirming the
pairing is complete.
If you hear one long beep, the pairing sequence has
failed or the wiring is incorrect.
This is a one time pairing and is not required when
changing the batteries of the Remote or Control Module.
The remote control system is now ready to use.
SÓLAS One-Touch
Programmable
Thermostatic Remote
Part #S-507
NOTE: The batteries in your SÓLAS One-Touch
remote control and control module are to be
replaced annually.
RESET Button
SÓLAS One-Touch
Control Module
Part #S-504
solasfires.com
39
SÓLAS ONE-TOUCH REMOTE OPERATION
HOW TO TURN YOUR FIREPLACE OFF
(INCLUDING PILOT)
Familiarize yourself with each of these methods before
operating your fireplace.
Remote and Wall Touch Pad: Press and hold the ON-OFF
button for a second (either on the Remote or the optional
Wall Touch Pad).
If the flames are on, they go down and you hear the valve
motor wind down. You hear a clunk and a beep indicating
that the valve has received the signal from the Remote.
AM
PM
Countdown
Timer
Thermostatic
Mode
ON/OFF
Increase Flame
Program
Mode
Decrease Flame
Split Flow Mode
Auxiliary Feature
HOW TO ENSURE YOUR FIREPLACE
CANNOT BE TURNED ON
INADVERTENTLY
Main Display
(not used)
(not used)
Light (not used)
Comfort Blower
(used if unit is
equipped with
blower)
You can use the following method to ensure that your
fireplace will not turn on when you don’t want it on.
First, ensure your fireplace is turned off—including the
pilot—and cold BEFORE going ahead.
SÓLAS One-Touch
Programmable
Thermostatic Remote
Part #S-507
• Close the shut-off valve on the gas supply line to
the appliance.
• Remove all batteries from the Control Module as well as
the batteries from the Remote.
• If unit is hardwired, shut-off power at the breaker.
Automatic Shut-Off (in certain conditions)
Your fireplace’s Remote is equipped with an automatic
shut-off mechanism which is activated in certain
conditions. See page 45 in the Remote Control Operation
section for a description of this feature.
UP
ON-OFF
NOTE: Before using the remote control system for
the first time, the Control Module and the Remote are
synchronized at the factory. See the section SÓLAS
Remote Pairing Set-up on page 39 of this manual if the
Control Module and Remote lose synchronization.
DOWN
IMPORTANT: BEFORE YOU BEGIN, please note that
with this system, the settings of time, temperature and
automatic ON/OFF can only be programmed when the
function display is flashing. Be patient when programming
as it does take time to set-up.
SÓLAS Wall Touch Pad*
(Optional)
Part #WTP-1500
*Not Compatible with SÓLAS Self-Calibrating Power Vent Kit
40
S Ó L AS CO NTE MPO R ARY F IR E
SÓLAS ONE-TOUCH REMOTE OPERATION
ONE-TOUCH REMOTE MAIN DISPLAY OVERVIEW
Child Proof
Time
Signal Indicator
Thermostatic Mode
Battery Status
AM
PM
Countdown Timer
Comfort Blower
°F or °C
Program Mode
Light (not used)
ON
OFF
Split Flow Mode
(not used)
Temperature
Auxiliary Feature (not used)
DO NOT leave the Remote on the hearth, mantel, or on top of the
fireplace. Use the Remote wall mount holder provided.
The SÓLAS One-Touch
Remote Control comes
with a wall bracket.
Mount the wall
bracket in the same
room as the fireplace.
Approximately 8-10
feet from the fireplace.
solasfires.com
41
SÓLAS ONE-TOUCH REMOTE OPERATION
TO TURN ON FIREPLACE
TO TURN OFF FIRE
• Press
to turn OFF.
When the pilot is off, it will
take 2 minutes before it
can be lit again.
CAUTION
WHEN PILOT IGNITION IS CONFIRMED, MOTOR
TURNS AUTOMATICALLY TO MAXIMUM FLAME
HEIGHT.
NOTE: There is a 2 minute delay
One-Touch Lighting (default):
AM
PM
after switching off before the next
ignition is possible.
Press and hold
for 4 seconds,
until 8 short beeps and a blinking
series of lines confirms the start
sequence has begun. Release
button.
Main gas flows once pilot ignition
is confirmed.
Remote automatically goes into
manual mode after main burner
ignition. The fireplace will default
to HI flame.
CAUTION
Always check the fire and pilot visually to ensure they
are off.
FLAME HEIGHT ADJUSTMENT
AM
PM
To decrease flame height, press and
hold . You may hold the button
down until the fire is set to pilot
flame only.
STANDBY MODE (PILOT FLAME)
AM
PM
To increase flame height, press and
hold .
Press and hold
to set
appliance to pilot flame.
DESIGNATE LOW AND HIGH FIRE
AM
NOTE: Flame goes to high fire first
before going to designated low fire.
CAUTION
If the pilot does not stay lit after several tries call your
local service technician or gas supplier.
AM
42
Double-Click DOWN Arrow
button. “LO" is displayed.
S Ó L AS CO NTE MPO R ARY F IR E
Double-Click UP Arrow
button.
Flame automatically foes to high
fire. “HI" will be displayed.
SÓLAS ONE-TOUCH REMOTE OPERATION
SETTING CELSIUS OR FAHRENHEIT
To change between °C and °F, press and hold
simultaneously.
CHILD PROOF
+
Your Remote can be set to lock out all commands to the
fireplace, except OFF.
Note: W
hen Remote is in °C
(Celsius) mode the clock will
be 24-hour. When Remote is
in °F (Fahrenheit) mode the
clock will be 12-hour.
AM
PM
To turn Child Proof ON:
1. Press and hold
2.
+
simultaneously.
is displayed. Child Proof is now active.
To turn Child Proof OFF:
1. Press and hold
+
simultaneously.
2. disappears. Child Proof is now inactive, and the
Remote has full function.
COUNTDOWN TIMER
SETTING THE TIME
1. Press
+
simultaneously. Day flashes.
2. Press + to select a number to correspond
with the day of the week.
• 1 = Monday
• 2 = Tuesday
• 3 = Wednesday
• 4 = Thursday
• 5 = Friday
• 6 = Saturday
• 7 = Sunday
+
3. Press
simultaneously. Hour flashes.
4. To select hour press
5. Press
+
or
.
simultaneously. Minutes flash.
6. To select minutes press
or
7. To confirm, press
simultaneously or wait.
AM
or
.
You can set your fireplace to automatically turn off at the
end of a timer.
To set a Countdown Timer:
1. Press and hold
until
displayed. Hour flashes.
is
to select Hour.
2. Press or
3. To confirm, press . Minutes flash.
to select Minutes.
4. Press or
or wait.
5. To confirm, press
To turn off a Countdown Timer:
1. Press , and the
disappears.
countdown
NOTE: The Countdown Timer only works in Manual and
Thermostatic modes. Maximum countdown time is
9 hours and 50 minutes.
COMFORT BLOWER OPERATION
Setting:
1. Press and hold
until
flashes.
2. Press
to increase or
to
decrease Comfort Blower speed.
3. To confirm setting, either press
or wait.
is displayed.
ress
until all 4 speed level
OFF: P
bars disappear.
NOTE: When setting, if the Comfort
Blower was not switched off
after last use, it starts automatically 4 minutes
after ignition at maximum speed, and goes to
the last set level after 10 seconds. The Comfort
Blower stops 10 minutes after the main burner is
extinguished.
solasfires.com
43
SÓLAS ONE-TOUCH REMOTE OPERATION
MODES OF OPERATION
Manual Mode
The ON/OFF status of the fireplace, as well as flame
height, are manually controlled by the user.
NOTE: The set temperature for Thermostatic Mode is the
temperature for the ON time in Program Mode.
Changing the Thermostatic Mode set temperature
also changes the ON time temperature in
Program Mode.
Default Settings:
Thermostatic Mode
The room temperature is measured
and compared to the set temperature.
The flame height is automatically
adjusted to achieve the set
temperature.
• ON TIME (Thermostatic) TEMPERATURE: 70°F / 21°C
" (pilot flame only)
• OFF TIME TEMPERATURE: “
Temperature Setting:
ON:
Press . is displayed. Preset
temperature displays briefly, followed by the room
temperature.
Setting Desired Temperature:
1. Press and hold
until
flashes. ON and
set temperature (set in Thermostatic Mode)
is displayed.
2. To continue, press
or wait.
displayed, temperature flashes.
, OFF
1. Press and hold until is displayed
and set temperature flashes.
2. To adjust set temperature,
press or .
3. To confirm, press or wait.
3. Select off temperature by pressing
OFF:
Day Setting:
1. Press
4. To confirm, press
or
3. Press
to go to Program Mode.
to go to Manual Mode.
Program Mode
The temperature is controlled by
Programs 1 and 2, each of which can
be set to go on and off at specific
times, at a set temperature.
or
.
.
NOTE: The on (Thermostatic) and off set temperatures
are the same for each day.
.
2. Press
ON
ON
OFF
1. ALL flashes. Press or
to choose
between:
• ALL = same settings ON-OFF every day
• SA:SU = same settings ON-OFF Saturday
and Sunday
• 1 , 2, 3, 4, 5, 6, 7 = daily timer—unique
ON-OFF settings for a single day of the
week, for multiple days of the week or for
every day of the week.
2. To confirm, press
.
ALL Selected
On Time Setting (PROGRAM 1)
1. , 1, ON are displayed.
ALL is displayed briefly. Hour flashes.
PROGRAM MODE
ON:
Press .
, 1 or 2, ON or OFF are displayed.
OFF:
1. Press , or
Manual Mode.
to go to
2. Press to go to Thermostatic Mode.
44
2. To select hour, press
ON
OFF
or
.
3. To confirm, press .
, 1, ON are
displayed. ALL displayed briefly.
Minutes flash.
4. To select minutes, press
5. To confirm, press
S Ó L AS CO NTE MPO R ARY F IR E
.
or
.
ON
SÓLAS ONE-TOUCH REMOTE OPERATION
LOW BATTERY INDICATION
PROGRAM MODE (Continued)
Off Time Setting (PROGRAM 1)
CAUTION
1. , 1, OFF are displayed. ALL is
displayed briefly. Hour flashes.
2. To select hour, press
or
Do not use a screwdriver or other metallic object
to remove the batteries from the Control Module
battery holder or the Remote. This could cause a
short circuit.
OFF
.
3. To confirm, press .
, 1, OFF
are displayed. ALL displayed
briefly. Minutes flash.
4. To select minutes, press
5. To confirm, press
or
.
.
NOTE: Either continue to PROGRAM 2 and set ON and
OFF times or stop programming at this point, and
PROGRAM 2 remains deactivated.
NOTE: PROGRAM 1 and 2 use the same ON
(Thermostatic) and OFF temperatures. Once a
new ON (Thermostatic) and/or OFF temperature
has been set, that temperature becomes the new
default setting.
NOTE: ON and OFF times programmed for PROGRAM 1
and PROGRAM 2 become the new default times.
The batteries must be removed to clear the PROGRAM 1
and PROGRAM 2 ON and OFF times and temperatures.
Remote
will show when the battery needs
The battery icon
to be replaced. Replace with two 1.5 V AAA alkaline
batteries.
Control Module
Frequent beeps for 3 seconds when the motor turns
indicate the batteries in the battery holder of the Control
Module need to be replaced. Replace with four 1.5 V AA
alkaline batteries.
AUTOMATIC SHUT-OFF
SA: SU or Daily Timer (1-7) Selected
• Set ON time and OFF time using the same procedure
as “ALL Selected” above.
• Waiting to finish setting.
NOTE: The batteries in your SÓLAS One-Touch
remote control and control module are to be
replaced annually. Only use brand-name alkaline
batteries such as Duracell or Energizer.
Countdown Timer
At the end of countdown time period, the fire turns
off. The Countdown Timer only works in Manual and
Thermostatic. Maximum countdown time is 9 hours and
50 minutes.
Seven Day Shut Off
If there is no activity for 7 days, the SÓLAS fireplace will
automatically shut down the pilot as required by certain
jurisdictions.
AUTOMATIC TURN DOWN
3 Hour No Communication Function
If your fireplace and remote are inactive for three hours—
for example, if the remote is left in another room—your
fireplace automatically turns down to pilot.
Benefit
SÓLAS products are designed with a focus on safety and
environmental responsibility. This will help save fuel and
is an environmental benefit. Program the temperature
and timer modes to maximize your heating efficiency.
solasfires.com
45
SÓLAS ONE-TOUCH REMOTE OPERATION
ERROR
CODE
F04
MESSAGE
F04
DURATION OF
DISPLAY
SYMPTOM
POSSIBLE CAUSE
4 seconds
• No pilot flame within 30 sec
• Note: After 3 failed ignition
sequences, F06 shown
• No gas supply
• Air in pilot supply line
• No spark
• Reversed polarity in thermocouple
wiring
• No gas supply
• Air in pilot supply line
• No spark
• Reversed polarity in
thermocouple wiring
• Incorrect pilot orifice if valve has
been converted from LPG to NG
or vice versa
F06
F06
4 seconds
• 3 failed ignition sequences
in 5 minutes
• Fire is not responding,
no pilot flame
F07
Low Battery
Symbol
Permanent
• Battery icon flashes on
Remote display
• Low battery in Remote
F09
F09
4 seconds
• Fire is not responding
• No electronic control of fire
• Down arrow button
was not
pressed during pairing
• Control Module and Remote are
not synced
• Fire is not responding
• Intermittent response
• No electronic control of fire
• No or bad connection between
Control Module and Remote
• No power at Control Module
(batteries low)
• Low communication range
(main adapter faulty, Remote
not communicating with
Control Module)
F46
F46
4 seconds
SÓLAS ONE-TOUCH REMOTE TIPS
• Double-click
flame setting.
to go directly to LO (lowest)
• Don’t leave the Remote on the mantel or hearth or any
hot surfaces. Use the Remote wall holder provided.
• Double-click
flame setting.
to go directly to HI (highest)
• To keep out of children’s reach, use the Remote wall
holder provided.
• Only use brand name alkaline batteries, such as
Duracell or Energizer.
• When using the Remote, it should be within 15 feet
(4.5 meters) of the fireplace.
• Be patient when programming: it takes time to set-up.
• Once you turn a pilot off, it takes a few minutes before
your can turn it back on.
Your SÓLAS Dealer is here to help, if you have any trouble with your SÓLAS
Fireplace or SÓLAS One-Touch Remote. Please contact your Dealer for support.
46
S Ó L AS CO NTE MPO R ARY F IR E
GAS CONVERSION
SÓLAS appliances are shipped from the factory ready for Natural Gas and are field convertible to Propane when a SÓLAS
gas conversion kit is used. Gas conversions must be performed by a qualified service technician, or licensed gas fitter
where local code requires. Installation must be performed by a licensed service technician, if not the warranty is void.
SÓLAS Gas Fireplaces are approved for installation at elevations up to 2000 feet in the U.S. and 1370 meters (4500 feet)
in Canada Without change. If your installation is at an elevation greater than those noted, consult with the local authority
having jurisdiction for gas product installations to determine their specific requirements for high altitude installations.
PART #
DESCRIPTION
SL26-LPC
TWENTY6 LP CONVERSION KIT
SÓLAS CONVERSION KIT CONTENTS
#27 PILOT ORIFICE
1. The burner is retained by (2) #10 sheet metal screws at
the rear of the burner at the far left and right sides, see
white arrows in the image below. Remove these (2) #10
sheet metal screws using a 5/16” extended nut driver
and ratchet.
#53 LP BURNER ORIFICE – 1PC
#8 SCREW – 1PC
2. Slide the burner to the right side of the firebox, lift the
right side of the burner first to disengage the burner
from the burner orifice.
3. Using a 9/16” deep socket, remove and replace the
burner orifice with the correct orifice provided in the
conversion kit.
solasfires.com
47
GAS CONVERSION
4. When converting to propane, remove collar on
burner inlet tube. When converting to natural gas
install collar over burner inlet tube and secure with
#8 sheet metal screw provided using a 1/4" nut driver.
Collar OFF for LP
7. Using a 10mm wrench, remove the pilot gas line and
swap the pilot orifice with the one supplied in the
conversion kit. Be sure that the pilot orifice is fully
seated and the pilot gas line is tightened properly
to prevent leaks around the orifice. If not seated
properly this will cause an unusually high pilot flame.
Collar ON for NG
5. Remove the (2) #10 sheet metal screws using a 5/16"
nut driver that hold the pilot assembly in the fireplace.
6. Lift the pilot assembly into the fireplace which
will give you access to the fittings under the pilot
assembly. Take extra caution to not damage ceramic
electrode on pilot assembly.
Pilot orifice
correctly sealed
8. Once the pilot gas line is tightened, reinstall the pilot
assembly in the fireplace using the two #10 sheet
metal screws provided. Ensure pilot gasket is intact.
9. Reinstall the burners in the fireplace and the burner
link (if required) with #10 sheet metal screws using a
5/16" nut driver.
(continued on next page)
48
S Ó L AS CO NTE MPO R ARY F IR E
GAS CONVERSION
GAS FLOW ADJUSTMENT
It is required you adjust the gas valve when converting
the fireplace.
3. The entire gas valve assembly is on flexible connectors
which allows you to lift it out of the fireplace as shown.
Be sure all wires and gas lines are free when pulling
gas valve assembly out of fireplace.
1. Locate and remove the pressure conversion brass plug
and set it for NG or LP accordingly. Reinstall and tighten.
4. Confirm inlet pressure of gas (top pressure tap on
valve) is between 5.5" w.c. to 10.0" w.c. for natural
gas and 11" w.c. to 13" w.c. for propane. If pressure is
not within these parameters, correct any gas supply
pressure issue before continuing with conversion.
Close the pressure tap.
5. Install a pressure gauge on the outlet pressure tap
on the valve.
6. Light the fireplace using the remote control.
7. With the fireplace set on the highest flame level, set the
high manifold pressure by adjusting the small flat screw
set within the brass pressure conversion plug. Refer to
the chart below for high pressure settings which vary
per model fireplace.
2. Locate and loosen the two 1/4" - 20 nuts under gas
valve assembly in the front of the fireplace, using a
7/16" socket with 6" exension. To locate the second
one it is necessary to swing the receiver module
up to the left.
8. With the fireplace set on the lowest flame level, set
the low manifold pressure by adjusting the 4mm allen
screw on the bottom side of the valve. Refer to the
chart below for low manifold pressure settings which
vary per model fireplace.
9. Ensure all pressure taps are closed and check all
connections/pressure taps for leaks.
(continued on next page)
MANIFOLD PRESSURE SPECIFICATIONS
MODEL
TWENTY6 - LP
HIGH PRESSURE
LOW PRESSURE
10.0” w.c. / 2.48kPa
4.25” w.c. / 1.1kPa
solasfires.com
49
GAS CONVERSION
GAS CONVERSION LABEL INSTRUCTIONS
1. When converting this fireplace, use a permanent marker to complete the supplied gas conversion label then affix it to
the right side of fireplace above the control module as pictured below.
S ÓL AS
This fireplace has been converted in the field. This label must
be filled out with indelible ink and affixed in a conspicuous
location near the appliance listing label.
Appliance Model: ______________
Converted to: ■ NG
■ LP
Gas Conversion Kit No. ____________________________________
This Appliance was Converted on (MM/DD/YYYY): ______________
This Gas Conversion was Completed by: ______________________
Address: _______________________________________________
______________________________________________________
CAUTION:
This gas conversion must be completed by a licensed gas installer.
Manufactured by: Progressive Manufacturing Inc., 452 Sunapee St., Newport, NH 03773 USA
2. Affix the supplied rating plate conversion label to the rating plate. Be sure to not cover the Model and Gas Pressure
information for the model and fuel you are converting to. With a permanent marker, check off the fuel type you are
converting to.
SÓLAS – DIRECT VENT GAS FIREPLACES
MODEL NOS. BI-26N, BI-26P
VENTED GAS FIREPLACE HEATER
NOT FOR USE WITH SOLID FUEL.
SER. NO.
BI-26-
THIS APPLIANCE IS EQUIPPED FOR:
PROPANE (LP) GAS
NATURAL GAS
Input Rating-Btu/hr
Min. Input Rating-Btu/
hr Orifice - DMS
Manifold Pressure
Min. Supply Pressure
Max. Supply Pressure
Natural Gas
This19,000
Fireplace
11,000
has
been
5/64”
converted.
5.0”wc/1.3kPa
See conversion
5.5”wc/1.4kPa
label in fireplace.
10.0”wc/2.5kPa
Propane
19,000
11,000
#55
10.0”wc/2.5kPa
11.0”wc/2.8kPa
13.0”wc/3.3kPa
Debit Calorifique
Puissance Minimum
L’injector
Press. A la tubulure
Press. D’Arrivée Min
Press. D’Arrivée Max
This product has been tested and listed by PFS TECO to ANSI
Z21.88-2016 · CSA 2.33-2016 Vented Gas Fireplace Heaters and CSA
2.17-2017, Gas-Fired Appliances For Use At High Altitudes and CSA
P.4.1-09. This appliance is equipped only for altitudes from 0-2000 feet
(0-610m) in the USA and 0-4500 feet (0-1370m) in Canada without
change. This appliance must be installed in accordance with local codes,
if none, follow the National Fuel Gas Code, ANSI Z223.1 or Canadian
Installation Codes, CAN/CSA-B149.1. This Appliance must be properly
connected to a venting system in accordance with the manufacturer’s
installation instructions.
MINIMUM CLEARANCES TO
COMBUSTIBLE CONSTRUCTION:
0” (0mm)
Fireplace Surround to L. Side Wall
0” (0mm)
Fireplace Surround to R. Side Wall
0” (0mm)
Fireplace Surround to Corner Wall
0” (0mm)
Fireplace Surround to Ceiling Wall
0” (0mm)
Fireplace Surround to Rear Wall
0” (0mm)*
Fireplace Surround to Floor
50
*The minimum required clearance to be maintained from the fireplace to
combustible flooring is measured from the top surface of carpeting, tile, etc.
Ó L AS CO NTE MPO R ARY F IR E
SUPPLIED COOL ZONE KIT MUST BESINSTALLED.
This Fireplace
has been
converted.
See conversion
label in fireplace.
MAINTENANCE
ANNUAL MAINTENANCE
A qualified service agency should conduct an annual
inspection and maintenance of your SÓLAS Gas Fireplace
including the overall installation and venting to keep
it running safely. The following procedures should be
performed only by a qualified service technician. The
gas supply should be turned off and the stove should be
completely cool whenever a maintenance procedure is
performed. All parts of the appliance that are removed for
servicing must be replaced prior to operation.
This appliance should be inspected before use and
at least annually by a qualified service technician.
More frequent cleaning may be required due to
excessive dust or lint from carpeting, bedding
materials, pets, etc. It is imperative that control
compartments and circulating air passageways of
this appliance be kept clean.
CLEANING THE BURNER & FIREBOX
During the annual inspection and maintenance
appointment, the service technician should clean the
burner and firebox. To gain access to the firebox and
burner, follow the instructions beginning on page 35
and 36 of this manual.
DO NOT USE A VACUUM CLEANER TO CLEAN THE
GLASS BURNER MEDIA.
A vacuum cleaner may be used to clean the metal parts
of the firebox. Leave the glass burner media in place.
Use a soft brush to clean the burner glass media. If the
burner media does need to be removed, carefully scoop
it off the burner and avoid dropping glass pieces in the air
gaps around the burner. Follow the instructions on page
34 of this manual when replacing the burner media on the
burner top.
AIR FLOW
The SÓLAS Gas Fireplace utilizes a convection air heat
exchange system to maximize heat delivered from the
fireplace. It is important that air flows freely through the
convection air system and out the air grills. Do not place
objects against the fireplace that will block the convection
air inlet flow or in front of any air outlet.
CLEANING GLASS AND PORCELAIN
ENAMEL PANELS
WARNING: Never clean the Glass or Enamel Panels
while they are hot. Do not use abrasive cleaners or
cleaners containing ammonia.
When the fireplace is first operated, there may be some
vapors and a visible white film left on the glass and
panels. This white film, a mineral deposit, is a normal
by-product of the combustion process in a gas appliance.
The composition of the deposit varies with location and
time and is believed to be associated with varying sulfur
content in the gas. You may experience this problem
intermittently.
We have consulted with ceramic glass manufacturers and
they cannot offer a definitive solution to the issue. The
following are recommendations only and are not meant
to guarantee results. NOTE: This is an issue beyond
SÓLAS’s control and is not covered under warranty.
• Clean the glass and porcelain enamel panels regularly
as soon as you notice a white film build-up. If the film is
left for a longer period of time it will etch into the glass
and may be harder or impossible to remove.
• NEVER use an abrasive cleaner or an Ammonia-based
cleaner on the ceramic glass. An abrasive cleaner will
compromise the strength of the glass, An emulsion type
cleaner is recommended.
• Use a damp, soft micro-fiber cloth or cotton cloth to
apply the cleaner. Dry glass with a soft, dry cloth. (Paper
towels and synthetic materials are abrasive to ceramic
glass and should not be used)
• We have had good results from the following products,
however we cannot guarantee results; Brasso, Polish
Plus by Kel-kem, Cook Top Clean Creme by Elco, White
Off by Rutland, Turtle Wax.
• DO NOT CLEAN GLASS WHILE IT IS HOT!
NOTE: The batteries in your SÓLAS One-Touch
remote control and control module are to be
replaced annually. Only use brand name alkaline
batteries such as Duracell or Energizer.
solasfires.com
51
MAINTENANCE
BATTERY REPLACEMENT
5. Replace the battery cover, slide control module back
into the fireplace and tighten silver thumb screw.
CONTROL MODULE BATTERIES
6. To reinstall the safety screen, reverse the steps on
page 35.
Inside your fireplace, there are (4) AA batteries installed
inside of the control module.
Frequent beeps for 3 seconds when the motor turns
indicates the batteries inside the Control Module are low.
1. Remove air panel, left and right side panels and screen
as shown on page 35.
2.Loosen silver thumb screw located on the top right side
of the control module.
SÓLAS ONE-TOUCH REMOTE
BATTERIES
Your remote display will indicate when the batteries
are low
.
The remote uses a (2) AAA alkaline batteries—we
recommend a name brand such as Duracell or Energizer.
The batteries should last one full season, depending on
usage.
Remove the batteries in the off-season to extend
battery life.
3. Slide the control module assembly up and to the
left as shown.
4. The cover on the control module slides up, exposing
the (4) AA batteries. Replace with (4) AA alkaline
batteries. We recommend a name brand such as
Duracell or Energizer.
NOTE: Even though your fireplace is hardwired to
120V in your home, the batteries in your SÓLAS
One-Touch remote control and control module are to
be replaced annually. Only use brand name alkaline
batteries such as Duracell or Energizer.
52
S Ó L AS CO NTE MPO R ARY F IR E
MAINTENANCE LOG
We strongly recommend that you keep a log of the regular maintenance that is performed on your
SÓLAS fireplace. We have provided the maintenance form below to make it easy. Simply ask your
qualified service technician to fill out one of the maintenance record forms below each time the
fireplace is serviced. This will help insure that all of the required maintenance procedures have
been completed, at least annually. Regular maintenance will help keep the fireplace functioning in
a safe and reliable manner. Additional forms are available from your installer or service technician
when needed.
Date of Service: ____________________________
Date of Service: ____________________________
Serviced By:_______________________________
Serviced By:_______________________________
Service Performed:
n Clean Burner & Firebox
Service Performed:
n Clean Burner & Firebox
n Clean Control Area
n Clean Control Area
n Clean Convection Air System
n Clean Convection Air System
n Leak Test Gas Connections
n Leak Test Gas Connections
n Replace Batteries in Control Module & Remote
n Replace Batteries in Control Module & Remote
n Clean Firebox Panels and Glass
n Clean Firebox Panels and Glass
n Other___________________________________
n Other___________________________________
Date of Service: ____________________________
Date of Service: ____________________________
Serviced By:_______________________________
Serviced By:_______________________________
Service Performed:
n Clean Burner & Firebox
Service Performed:
n Clean Burner & Firebox
n Clean Control Area
n Clean Control Area
n Clean Convection Air System
n Clean Convection Air System
n Leak Test Gas Connections
n Leak Test Gas Connections
n Replace Batteries in Control Module & Remote
n Replace Batteries in Control Module & Remote
n Clean Firebox Panels and Glass
n Clean Firebox Panels and Glass
n Other___________________________________
n Other___________________________________
Date of Service: ____________________________
Date of Service: ____________________________
Serviced By:_______________________________
Serviced By:_______________________________
Service Performed:
n Clean Burner & Firebox
Service Performed:
n Clean Burner & Firebox
n Clean Control Area
n Clean Control Area
n Clean Convection Air System
n Clean Convection Air System
n Leak Test Gas Connections
n Leak Test Gas Connections
n Replace Batteries in Control Module & Remote
n Replace Batteries in Control Module & Remote
n Clean Firebox Panels and Glass
n Clean Firebox Panels and Glass
n Other___________________________________
n Other___________________________________
solasfires.com
53
REPLACEMENT PARTS LIST
PART NAME
P/N
PART NAME
P/N
Pilot Head NG/LP
M26-501N / M26-501 P
Burner Orifice (NG)
26N-509
Pilot Thermocouple*
M26-502*
Burner Orifice (LP)
26P-509
Pilot Injector (NG)
26N-503
Burner Glass Media – Clear
26-511
Pilot Injector (LP)
26P-503
Burner Module (NG)
26N-901
SÓLAS One-Touch Control Module
S-504
Burner Module (LP)
26P-901
Wall Touch Pad** (Optional)
WTP-1500
Firebox Enamel Panel – Rear
26-512
SÓLAS One-Touch Remote
S-507
Firebox Enamel Panel – Left
26-513
Gas Valve (Maxitrol)
M46-515
Firebox Enamel Panel – Right
26-514
TC Line Red
M46-701
Thermocouple Interrupter Block
M46-703
TC Line Yellow
M46-702
8-Wire Connecting Cable
M46-704
Glass Assy (including gasket & frame)
26-510
*This is a quick response thermocouple. Replace it only with SÓLAS Part Number M26-502.
**Not Compatible with SÓLAS Self-Calibrating Power Vent Kit
For Replacement Parts and customer service,
contact your SÓLAS Dealer or;
SÓLAS, LLC
452 Sunapee Street, Newport, NH 03773
P (603) 298-5169 [email protected]
54
S Ó L AS CO NTE MPO R ARY F IR E
CONTROL SCHEMATIC
Comfort Blower
Pilot Assembly
8 Wire
Connecting
Cable
GV60 Gas Valve
Thermocouple
Thermo Current
Yellow Cable
Integrated Interrupter Block
Thermo Current
Red Cable
Electrode (Ignition) Cable
UP
ON-OFF
Power Cord
DOWN
Module for additional function
AM
PM
Connecting Cable
Receiver - Module
SÓLAS One-Touch
Remote Handset
Control Module
Wall Touch Pad*
(Optional)
*Not Compatible with
SÓLAS Self-Calibrating
Power Vent Kit
Caution
Label all wires prior to disconnection when servicing
the controls. Wiring errors can cause improper and
dangerous operation. Verify proper operation after
servicing.
solasfires.com
For Replacement Parts and customer service,
contact your SÓLAS Dealer or;
SÓLAS, LLC
452 Sunapee Street, Newport, NH 03773
P (603) 298-5169 [email protected]
55
WARRANTY INFORMATION
THE WARRANTY
SÓLAS, LLC, a division of Progressive Manufacturing, Inc. (“SÓLAS"), Limited Lifetime
Warranty warrants your SÓLAS brand gas fireplace (“Product") to be free from defects
in materials and workmanship at the time of manufacture. The Product body and
firebox carry the Limited Lifetime Warranty on workmanship defects causing loss
of structural integrity. Ceramic glass carries the Limited Lifetime Warranty against
thermal breakage only. After installation, if covered components manufactured by
SÓLAS are found to be defective in material or workmanship during the Limited
Lifetime Warranty period and while the Product remains at the site of the original
installation, SÓLAS will, at its option, repair or replace the covered components. If
repair or replacement is not commercially practical, SÓLAS will, at its option, refund
the purchase price or wholesale price of the SÓLAS product, whichever is applicable.
SÓLAS will also pay their prevailing labor rates, as determined in its sole discretion,
incurred in repairing or replacing such components during the warranty period.
THERE ARE EXCLUSIONS AND LIMITATIONS to this Limited Lifetime Warranty as
described herein.
COVERAGE COMMENCEMENT DATE
Warranty coverage begins on the date of installation. The warranty shall commence
no later than 24 months following the date of product shipment from SÓLAS,
regardless of the installation date.
EXCLUSIONS AND LIMITATIONS
This Limited Lifetime Warranty applies only if the Product is installed in the United
States or Canada and only if operated and maintained in accordance with the
printed instructions accompanying the Product and in compliance with all applicable
installation and building codes and good trade practices.
This warranty is non-transferable and extends to the original owner only. The Product
must be purchased through a listed supplier of SÓLAS and proof of purchase must
be provided. The Product body and firebox carry the Limited Lifetime Warranty. The
following do not carry the Limited Lifetime Warranty, but are warranted as follows:
• Burner – Repair or replacement for three years from date of installation.
•
Gas components & electrical components – Repair or replacement for one
year from date of installation.
•
Blowers & remote controls – Repair or replacement for one year from the
date of installation.
•
Porcelain Firebox Liners – Replacement for one year against cracking or
breakage due to thermal stress from date of installation. Excludes surface and
hairline cracks and scratches or slight color changes that do not affect the
operation or safety of the unit.
• Gaskets – Repair or replacement for one year from the date of installation.
• Surrounds – Replacement for one year against cracking or breakage due to
thermal stress. Excludes surface and hairline cracks and scratches or slight
color changes that do not affect the operation or safety of the unit.
• Labor coverage – Prevailing SÓLAS rates apply for the warranty period of the
component. SÓLAS will not be liable for travel costs for service work.
SÓLAS will not be responsible for: (a) damages caused by normal wear and tear,
accident, riot, fire, flood, or acts of God; (b) damages caused by abuse, negligence,
misuse, or unauthorized alteration or repair of the Product affecting its stability or
performance. The Product must be subjected to normal use. The product is designed
to burn either natural or propane gas only. Burning conventional fuels such as wood,
coal or any other solid fuel will cause damage to the Product, will produce excessive
temperatures and could result in a fire hazard. (c) Damages caused by failing to
provide proper maintenance and service in accordance with the instructions provided
with the Product; (d) damages, repairs or inefficiency resulting from faulty installation
or application of the Product.
Discoloration and some minor expansion, contraction, or movement of certain parts
and resulting noise is normal and not a defect, and, therefore, not covered under
warranty. The installer must ensure the appliance is burning as per the rating tag
at the time of installation. Over-firing (operation above the listed BTU rate) of this
appliance can cause serious damage and will nullify this warranty.
Damage to stainless steel, gold, nickel or porcelain enameled surfaces caused by
fingerprints, scratches, melted items, or other external sources left on these surfaces
from the use of cleaners is not covered in this warranty.
SÓLAS is not responsible for inadequate fireplace system draft caused by air
conditioning and heating systems, mechanical ventilation systems, or general
construction conditions which may generate negative pressure in the room in which
the appliance is installed. Additionally, SÓLAS assumes no responsibility for drafting
conditions caused by venting configurations, adjoining trees or buildings, adverse
wind conditions or unusual environmental factors and conditions that affect the
operation of the unit.
This Limited Lifetime Warranty covers only parts and labor as provided herein. In no
case shall SÓLAS be responsible for materials, components, or construction, which
are not manufactured or supplied by SÓLAS or for the labor necessary to install,
repair, or remove such materials, components, or construction. Additional utility
bills incurred due to any malfunction or defect in equipment are not covered by this
warranty. All replacement or repair components will be shipped F.O.B. from the
nearest stocking SÓLAS facility.
LIMITATION ON LIABILITY
It is expressly agreed and understood that SÓLAS’ sole obligation and the
purchaser’s exclusive remedy under this warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement,
repair, or refund, as specified herein.
In no event shall SÓLAS be liable for any incidental or consequential damages
caused by defects in the Product, whether such damage occurs or is discovered
before or after repair or replacement, and whether such damage is caused by
SÓLAS’ negligence. SÓLAS has not made and does not make any representation or
warranty of fitness for a particular use or purpose, and there is no implied condition of
fitness for a particular purpose.
SÓLAS makes no expressed warranties except as stated in this Limited Lifetime
Warranty. The duration of any implied warranty is limited to the duration of this
expressed warranty.
No one is authorized to change this Limited Lifetime Warranty or to create for SÓLAS
any other obligation or liability in connection with the Product. Some states and
provinces do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. The provisions
of this Limited Lifetime Warranty are in addition to and not a modification of or
subtraction from any statutory warranties and other rights and remedies provided
by law.
INVESTIGATION OF CLAIMS AGAINST WARRANTY
SÓLAS reserves the right to investigate any and all claims against this Limited
Lifetime Warranty and to decide, in its sole discretion, upon the method of settlement.
To receive the benefits and advantages described in this Limited Lifetime Warranty,
the appliance must be installed and repaired by a licensed contractor approved by
SÓLAS.
Contact SÓLAS at the address provided herein to obtain a listing of approved
dealers/distributors. SÓLAS shall in no event be responsible for any warranty work
done by a contractor that is not approved without first obtaining SÓLAS’ prior written
consent.
HOW TO REGISTER A CLAIM AGAINST WARRANTY
In order for any claim under this warranty to be valid, you must contact the SÓLAS
dealer/distributor from which you purchased the product. If you cannot locate the
dealer/distributor, then you must notify SÓLAS in writing. SÓLAS must be notified of
the claimed defect in writing within 90 days of the date of failure. Notices should be
directed to the SÓLAS Warranty Department. Visit our website at www.solasfires.com/
warranty.
This warranty is void if:
a) The unit has been operated in atmospheres contaminated by chlorine,
fluorine or other damaging chemicals.
b) The unit is subject to submersion in water or prolonged periods of dampness
or condensation.
c) Any damage to the unit, combustion chamber, heat exchanger or other
components due to water or weather damage which is the result of, but not
limited to improper chimney/venting installation.
56
S Ó L AS CO NTE MPO R ARY F IR E
SÓLAS, LLC
P (603) 298-5169
F (603) 298-9246
solasfires.com/warranty
We recommend that our
gas hearth products be
installed and serviced by
professionals who are
certified in the U.S. by the
National Fireplace Institute®
(NFI) as NFI Gas Specialists.
www.NFIcertified.org
RECORD YOUR PRODUCT INFORMATION
Model #: ________________________ Serial Number: _______________________________
Date Purchased: __________________ Date Installed: ________________________________
THANK YOU FOR CHOOSING
solasfires.com
">