RC5P60™Appl
i
cat
i
onGui
de
Ci
scoSX80,CodecPr
o&CodecPl
us
Ci
sco
Pr
eci
si
on60
RCCC001
1
’HDMICabl
e
RCCC002
1
’UTPCabl
e
RCCH001
3’HDMICabl
e
PPC003
1
’PowerCabl
e
RCCH01
6
3’UTPCabl
e
RC5CE™
SCTLi
nk™Cabl
e
Power
,Cont
r
ol&Vi
deo
RC5HE™
TheSCTLi
nk™cabl
emus
tal
waysbe
as
i
ngl
e,poi
nt
t
opoi
ntCATcabl
ewi
t
h
nocoupl
er
sori
nt
er
connect
i
ons
.
SCTLi
nk™Cabl
eSpecs
I
nt
egr
at
or
Suppl
i
edCAT5e/
CAT6STP/UTPCabl
e
EI
A568A/EI
A568B(
1
0m1
00m mi
n/
maxLengt
h)
12345678
RJ45Pi
nout
12345678
Pi
n1
Modul
eDi
mensi
ons
RC5CE™Di
m:2.
5”
W x0.
875”
H x3.
6875”
D
RC5HE™Di
m:3.
75”
W x1
.
5”
H x3.
625”
D
gG oBbO brBR
oO gBbG brBR
T568A
T568B
W PS1
230VDC
1
00240V 4763Hz
PowerSuppl
y
RC5-P60™ Installation Instructions
Updated: 7/17/2020
Supporting the Cisco Precision 60 and
SX80, CodecPlus. and CodecPro Codecs
TEST YOUR LINK CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your LINK
cable’s wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1.
2.
3.
4.
5.
6.
7.
Test and verify your CAT5e/CAT6 STP or UTP SCTLink™ cable for EIA568A/EIA568B.
The SCTLink™ cable must be between 10m (minimum) and 100m (maximum) length.
Connect one end of the SCTLink™ cable to the “SCTLink™” connection on the Head End module.
Connect the other end of your SCTLink™ cable to the provided PowerSniffer.
Connect the WPS-12 power supply to the Head End module.
Connect the WPS-12 power supply to AC mains.
If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable.
Once your SCTLink™ cable has been tested, please disconnect the WPS-12 power supply from the Head End module,
and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1.
2.
3.
5.
Connect RCC-C001 video cable between the RC5-CE
Camera End’s HDMI connector labeled “VIDEO INPUT”
and the camera’s HDMI connector.
Connect the RCC-C002 control cable between the
RC5-CE’s RJ45 connector labeled “ETHERNET” and the
camera’s RJ45 input.
Connect the PPC-003 power cable between the RC5CE’s power connector labeled “+12V Power” and the
camera’s power input.
Please Note: ‘Ethernet 2’ supports an additional Precision
60 camera, or if extended, RC5-HE module. Please refer
to the visual guide on reverse side of this document.
6.
Connect one end of your SCTLink™ cable to the RC5-HE
module’s “SCTLink™” port. Connect the other end to the
RC5-CE module’s “SCTLink™” port.
7.
Connect the WPS-12 power supply to the RC5-HE’s
power input labeled “Power +30VDC”.
8.
At this point, your camera should have power and video
output onto your Cisco TouchPad (or other control
system that is correctly connected to your codec).
Connect the codec-end cables:
4.
Connect the RCC-H001 cable between the RC5-HE’s
HDMI connector, labeled “VIDEO OUT” and the codec’s
HDMI input.
Connect the RCC-H016 cable between the Cisco Codec’s
RJ45 Ethernet “Appliance” port and the RC5-HE’s RJ45
Layer 2 Ethernet port labeled ‘Port 1’.
• ALLOW UP TO TWO MINUTES FOR THE SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE
LED LABEL
ACTIVE STATUS
INACTIVE STATUS
RC5-CEEthernetSolid GreenOff
RC5-HE
HDCP
Solid Green or Blinking Green
Off
RC5-HE
OK/LINK
Alternating Blinking Red/Green; 1:1 Pattern Blinking Red (occassional single green)
RC5-HEPowerSolid GreenBlinking Red or off
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC5-P60.
CABLEDESCRIPTIONFUNCTION
RCC-C001
1’ HDMI Cable
Video connection between camera and RC5-CE module.
RCC-C002
1’ UTP Cable
Control connection between camera and RC5-CE module.
PPC-003
1’ Power Cable
Power connection between camera and RC5-CE module.
RCC-H001
3’ HDMI Cable
Video connection between codec and RC5-HE module.
RCC-H016
3’ UTP Cable
Control connection between codec and RC5-HE module.
Power Supply Specifications (AC-Mains Side) Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 30VDC
power supply uses 1.45 amperes AC maximum. All specs subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • © SOUND CONTROL TECHNOLOGIES, INC
">
