RC6CST™&RC6CSTKA*
™Appl
i
cat
i
onGui
de
I
mpor
t
ant
: Due t
o t
he power
demands of Ci
s
co’
s Speaker
Tr
ack 60,i
ti
s bes
tpr
act
i
ce t
o
ut
i
l
i
zeSCT’
spr
ovi
ded RCRKM™
r
acks
hel
ft
of
aci
l
i
t
at
event
i
l
at
i
on.
SCTLi
nk™Cabl
eSpecs
I
nt
egr
at
or
Suppl
i
edCAT6STP/UTPCabl
e
T568A orT568B(
1
0m1
00m mi
n/
maxLengt
h)
Ci
scoSpeaker
Tr
ack60
12345678
RJ45Pi
nout
12345678
Pi
n1
gG oBbO brBR
oO gBbG brBR
T568A
T568B
SCTLi
nk™Cabl
e
Power
,Cont
r
ol&DualVi
deo
TheSCTLi
nk™cabl
emus
tal
waysbeas
i
ngl
e,poi
nt
t
opoi
nt
CATcabl
ewi
t
hnocoupl
er
sori
nt
er
connect
i
ons
.
PPC01
01
.
0M
PowerCabl
e
RC6CE™
W PS4848VDC
1
00240V~
4763Hz
PowerSuppl
y
RC6HE™
RCCH01
61
.
0M
UTPCabl
e
RCCH01
61
.
0M
UTPCabl
e
[
2]RCCC01
1
1
.
0M
HDMICabl
es
270°Connect
or
Modul
eDi
mensi
ons
RC6CE™:H:1
.
08”(
27mm)xW :5.
20”(
1
32mm)xD:4.
82”(
1
42mm)
RC6HE™:H:1
.
39”(
35mm)xW :7
.
31
”(
1
85mm)xD:5.
28”(
1
34mm)
[
2]RCCH001
1
.
0M
HDMICabl
es
Ci
scoCodecPl
us/Pr
o
SX80,C40,C60&C90
RC6-CST™ & RC6-CST-KA™
Installation Instructions
Updated: 4/30/2021
TEST YOUR SCTLink™ CABLE
Supporting the Cisco SpeakerTrack 60,
Cisco Codec Plus, Codec Pro, SX80, C40, C60 & C90
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your
SCTLink™ wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1.
2.
3.
4.
5.
6.
7.
Test and verify your CAT6 STP or FUTP SCTLink™ cable for T568A or T568B.
The SCTLink™ cable must be between 10m (minimum) and 100m (maximum) length.
Connect one end of the SCTLink™ cable to the “SCTLink™” connection on the Head End module.
Connect the other end of your SCTLink™ cable to the provided PowerSniffer.
Connect the WPS-48 power supply to the Head End module.
Connect the WPS-48 power supply to AC mains.
If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable.
Once your SCTLink™ cable has been tested, please disconnect the WPS-48 power supply from the RC6-HE module,
and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Before integrating your RC6-CST™ kit, please ensure your Cisco SpeakerTrack base is connected to your two Cisco Precision
60 cameras (Power and Ethernet connections) via Cisco’s instructions.
Connect the camera-end cables:
1.
2.
3.
4.
Connect the first RCC-C011-1.0M video cable between
the RC6-CE’s HDMI connector labeled “HDMI INPUT 1”
and the first camera’s HDMI connector. The 270° HDMI
end will connect to the RC6-CE.
Connect the second RCC-C011-1.0M video cable between
the RC6-CE’s HDMI connector labeled “HDMI INPUT
2” and the second camera’s HDMI connector. The 270°
HDMI end will connect to the RC6-CE.
Connect the RCC-H016-1.0M control cable between the
RC6-CE’s RJ45 connector labeled “Ethernet” and the
SpeakerTrack’s rightmost RJ45 connector.
Connect the PPC-010-1.0M power cable between the
RC6-CE’s power output labeled “+12VDC Output” and
the SpeakerTrack’s power input.
Connect the codec-end cables:
5.
6.
7.
8.
9.
Connect the second RCC-H016-1.0M cable between the
Cisco supported codec’s RJ45 control connector and the
RC6-HE’s RJ45 connector labeled ‘Ethernet 1’.
Connect the first RCC-H001-1.0M cable between the
codec’s HDMI connector and one of the two HDMI
outputs labeled “HDMI OUT 1”.
Connect the second RCC-H001-1.0M cable between the
codec’s second HDMI connector and one of the two
RC6-HE’s HDMI connectors labeled “HDMI OUT 2”.
Connect one end of your SCTLink™ cable to the RC6-HE
module’s “SCTLink™” port. Connect the other end to the
RC6-CE module’s “SCTLink™” port.
Connect the WPS-48 Power Supply to the “48VDC
Input” jack on the RC6-HE Module.
• ALLOW UP TO TWO MINUTES FOR THE SPEAKERTRACK SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE
LED LABEL
ACTIVE STATUS
RC6-CEOK LEDBlinking Green (~1 second interval)
RC6-HEOK LEDBlinking Green (~1 second interval)
RC6-HELINK LEDSolid Blue
RC6-HE
HDCP LED
Blinking Green (~0.5 second interval)
Cable Table - Part numbers, descriptions and functions of all SCT cables provided.
The RC6-CST™ kit includes [1] RC-RKM™ Rack Shelf.
The RC6-CST-KA™ kit includes [1] RC-RKM™ Rack Shelf + [1] RCA-ST6™ Articulating Camera Mount.
CABLEDESCRIPTIONFUNCTION
RCC-C011-1.0M (x2)
270° HDMI Cable
Video connection between camera pair and RC6-CE.
PPC-010-1.0M
Power Cable
Supplies power from RC6-CE to SpeakerTrack base.
RCC-H001-1.0M (x2)
HDMI Cables
Dual-video connection between RC6-HE and codec.
RCC-H016-1.0M (x2)
RJ45 to RJ45
Control connection between RC6-HE and codec.
Control connection between SpeakerTrack and RC6-CE.
Power Supply Specifications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC
power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • ©SOUND CONTROL TECHNOLOGIES, INC
">
