RC7-CQC Installation Instructions
Supporting the Cisco Quad Camera and
Cisco SX80, Plus & Pro Codecs
TEST YOUR LINK CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your LINK
cable’s wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1.
2.
3.
4.
5.
6.
7.
Test and verify your CAT6 LINK cable for UTP 568A/568B. Link cable must be between 30ft - 300ft.
The LINK cable between the RC7-CE module (transmitter) & RC7-HE module (receiver)
must always be a single, point-to-point CAT cable with no couplers or interconnections.
Connect the provided PowerSniffer to the Quad Camera end of your CAT6 LINK cable.
Connect the other end of the LINK cable to the ‘SCT LINK” connection on the Head End module.
Connect the WPS-48 power supply to the Head End module.
Connect the WPS-48 power supply to AC mains.
If the SCT LINK cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable.
Once your cable has been tested, please disconnect the WPS-48 power supply from the RC7-HE module,
and the PowerSniffer from the LINK cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1.
2.
3.
4.
Connect the RCC-C014 HDMI cable between the Quad
Camera’s HDMI Input 1 and the RC7-CE’s “HDMI IN” port.
Connect the RCC-C015 UTP cable between the
Quad Camera’s RJ45 camera input and the RC7-CE’s
“Ethernet” port.
Connect the PPC-014 3’ power cable between the Quad
Camera’s power input and the RC7-CE’s “12VDC Output”
port.
If using an optional TRS audio cable, connect it between
the Quad Camera’s TRS audio input and the RC7-CE’s
“Line Out” port.
Connect the codec-end cables:
5.
6.
7.
codec’s HDMI camera input and the RC7-HE’s HDMI
“Output 1” port.
Connect the RCC-H016 3’ UTP control cable between the
codec’s RJ45 camera input and the RC7-HE’s “Ethernet
Port 1”.
If using an optional TRS audio cable, connect it between
the RC7-HE’s “Line In” TRS port.
Connect and Initiate the Extended System:
8.
Connect one end of your CAT6 LINK cable to the RC7HE module’s “SCT Link” port.
9. Connect the other end of the CAT6 LINK cable to the
RC7-CE module’s “SCT Link” port.
10. Connect the WPS-48 power supply to the RC7-HE.
Connect the RCC-H001 3’ HDMI cable between the
• ALLOW UP TO TWO MINUTES FOR THE QUAD CAMERA SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE
LED LABELACTIVE STATUSINACTIVE STATUS
RC7-CE
OK LED
Blinking Green (~1 second interval)
Blinking or Solid Red
RC7-HE
OK LED
Blinking Green (~1 second interval)
Blinking or Solid Red
RC7-HELINK LEDSolid GreenSolid Red or Dormant
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC7-CQC.
This kit is also inclusive of [1] RC-RKL Rack Shelf.
CABLEDESCRIPTIONFUNCTION
RCC-C014
1’ HDMI Cable
Video connection between Quad Camera and RC7-CE module.
RCC-C015
1’ UTP Cable
Control connection (ethernet) between Quad Camera and RC7-CE module.
PPC-014
1’ Power Cable
Power connection between Quad Camera and RC7-CE module.
RCC-H001
3’ HDMI Cable
Video connection between the codec and RC7-HE module.
RCC-H016
3’ UTP Cable
Control connection (ethernet) between the codec and RC7-HE module.
Power Supply Specifications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC
power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • ©SOUND CONTROL TECHNOLOGIES, INC
RC7CQC™Appl
i
cat
i
onGui
de
LI
NKCabl
eSpecs
I
nt
egr
at
or
Suppl
i
edCAT6STPCabl
e
EI
A568A orEI
A568B(
Mi
n.30’t
o300’Max)
Ci
scoQuadcam
12345678
RJ45Pi
nout
12345678
Pi
n1
Opt
i
onalTRSAudi
oCabl
e
*
Deal
erSuppl
i
ed*
RCCC01
5
1
’UTPCabl
e
PPC01
4
3’PowerCabl
e
gG oBbO brBR
oO gBbG brBR
T568A
T568B
RCCC01
4
1
’HDMICabl
e
RC7CE™
W PS4848VDC
1
00240V~
4763Hz
PowerSuppl
y
LI
NKCabl
e
Power
,Cont
r
ol
,Audi
o&Vi
deo
RC7HE™
Ci
s
coSuppl
i
edEt
her
netCabl
e
RCCH01
6
3’UTPCabl
e
RCCH001
3’HDMICabl
e
3r
dPar
t
y
Devi
ce
Opt
i
onalTRSAudi
oCabl
e*
Deal
erSuppl
i
ed*
Ci
scoCodecPl
us,SX80orCodecPr
o
Modul
eDi
mensi
ons
RC7CE™:1
.
625”
H x6.
625”
W x4.
625”
D
RC7HE™:1
.
625”
H x8.
875”
W x4.
625”
D
">