SCT RC8-CQC Application Guide

Sound Control Technologies RC8-CQC is a high-end extension kit designed to enhance the capabilities of Cisco video conferencing systems by enabling the use of a Cisco Quad Camera and providing extended connectivity options. With the RC8-CQC, users can experience superior video quality, flexible camera placement, and seamless integration with their existing Cisco codecs.

PDF Download

Document

RC8-CQC™ Installation Instructions
Updated: 4/8/2022
Supporting the Cisco Quad Camera and
Cisco SX80, Plus &amp; Pro Codecs
TEST YOUR SCTLink™ CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your
SCTLink™ wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1.
2.
3.
4.
5.
6.
7.
Test and verify your CAT6 STP SCTLink™ cable for T568A or T568B.
The SCTLink™ cable must be between 10m (minimum) and 100m (maximum) length.
Connect one end of the SCTLink™ cable to the “SCTLink™” connection on the Head End module.
Connect the other end of your SCTLink™ cable to the provided PowerSniffer.
Connect the WPS-48 power supply to the Head End module.
Connect the WPS-48 power supply to AC mains.
If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable.
Once your SCTLink™ cable has been tested, please disconnect the WPS-48 power supply from the RC8-HE module,
and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1.
2.
3.
Connect the RCC-C014 HDMI cables between the Quad
Camera’s HDMI 1 &amp; 2 connectors (angled end) and the
RC8-CE’s “HDMI 1” and “HDMI 2” ports.
Connect the RCC-C037-0.3M UTP cable between the
Quad Camera’s RJ45 Ethernet port (angled end) and the
RC8-CE’s Ethernet port.
Connect the PPC-018 power cable between the Quad
Camera’s power connector and the RC8-CE’s “+12VDC
Output” port.
Connect the codec-end cables:
4.
Connect two 3ft RCC-H001 HDMI cables between
the codec’s HDMI camera inputs and the RC8-HE’s
5.
6.
corresponding “HDMI Out 1 A” and “HDMI Out 2 A” port.
Connect the 3ft RCC-H016 UTP control cable between
the codec’s RJ45 camera Ethernet port and the RC8HE’s “Ethernet 1”.
Position the ARC Select switch fully right when sending
audio from the codec to the Quad Camera’s speaker
via HDMI Out 1A. Position switch fully left when sending
analog audio to the quad camera’s speaker.
Connect and Initiate the Extended System:
7.
8.
9.
Connect one end of your SCTLink™ cable to the RC8-HE
module’s blue “SCTLink™” port.
Connect the other end of the SCTLink™ cable to the
RC8-CE module’s blue “SCTLink™” port.
Connect the WPS-48 power supply to the RC8-HE.
• ALLOW UP TO TWO MINUTES FOR THE QUAD CAMERA SYSTEM TO INITIALIZE •
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE
LED LABELACTIVE STATUSINACTIVE STATUS
RC8-CE
OK LED 1 &amp; 2
Blinking Green (~1 second interval)
Blinking or Solid Red
RC8-HE
OK LED 1 &amp; 2
Blinking Green (~1 second interval)
Blinking or Solid Red
RC8-HELINK LEDSolid BlueSolid Red or Dormant
RC8-HEHDCP 1 &amp; 2Blinking GreenN/A
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC8-CQC™.
This kit is also inclusive of [1] RC-RKM™ Rack Shelf.
CABLEDESCRIPTIONFUNCTION
[2] RCC-C014-0.3M
Angled HDMI Cables
Video connection between Quad Camera and RC8-CE module.
RCC-C037-0.3M
Angled UTP Cable
Control connection (Ethernet) between Quad Camera and RC8-CE module.
PPC-018-0.4M
Power Cable
Power connection between Quad Camera and RC8-CE module.
[2] RCC-H001-1.0M
HDMI Cables
Video connection between the codec and RC8-HE module.
RCC-H016-1.0M
UTP Cable
Control connection (Ethernet) between the codec and RC8-HE module.
Power Supply Specifications (AC-Mains Side): Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum.
Turn-on Surge: Less than 60 amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 48VDC
power supply uses 2.80 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • &copy; SOUND CONTROL TECHNOLOGIES, INC
">

Hello! I am an AI chatbot specifically trained to assist you with the SCT RC8-CQC Application Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

Extends Cisco Quad Camera to Cisco SX80, Plus, or Pro Codecs
Transmits video and control signals over a single SCTLink™ cable
Supports CAT6 STP SCTLink™ cables up to 100m
Includes HDMI and UTP cables for connecting Quad Camera and codec
PowerSniffer and WPS-48 power supply for reliable operation
ARC Select switch for audio routing options

Frequently asked questions

The RC8-CQC allows you to connect a Cisco Quad Camera to a Cisco SX80, Plus, or Pro Codec, extending the capabilities of your video conferencing system.

The RC8-CQC uses CAT6 STP SCTLink™ cables.

The SCTLink™ cable can be between 10m and 100m in length.

The PowerSniffer is used to test the continuity and integrity of the SCTLink™ cable.

You can use the ARC Select switch to choose between sending audio from the codec to the Quad Camera's speaker via HDMI Out 1A or via analog audio connection.