RC4E4P™Appl
i
cat
i
onGui
de
Pol
yRPG300,RPG500,RPG700&G7500
Pol
yEagl
eEyeI
V
RCCH030
HDMI
/DB9t
o
HDCICabl
e
RC4HE™
RCCC030
HDMI
/RJ45t
o
Mi
ni
HDCICabl
e
RC4CE™
SCTLi
nk™Cabl
e
Power
,Cont
r
ol&Vi
deo
TheSCTLi
nk™cabl
emus
tal
ways
beas
i
ngl
e,poi
nt
t
opoi
ntCATcabl
e
wi
t
hnocoupl
er
sori
nt
er
connect
i
ons
.
SCTLi
nk™Cabl
eSpecs
I
nt
egr
at
or
Suppl
i
edCAT5e/
CAT6STP/UTPCabl
e
EI
A568A/EI
A568B(
1
0m1
00m mi
n/
maxLengt
h)
12345678
RJ45Pi
nout
12345678
Pi
n1
Modul
eDi
mensi
ons
RC4CE™:2.
5”W x0.
875”
H x3.
6875”
D
RC4HE™:3.
75”
W x1
.
5”
H x3.
625”
D
gG oBbO brBR
oO gBbG brBR
T568A
T568B
W PS1
230VDC
1
00240V 4763Hz
PowerSuppl
y
RC4-E4P™ Installation Instructions
Updated: 8/19/2020
Supporting the Poly EagleEye IV and
Poly RGP300/500/700 & G7500 Codecs
TEST YOUR LINK CABLE
We highly recommend using an Ethernet Network Tester/Analyzer alongside our provided PowerSniffer to confirm your LINK
cable’s wiring. Our PowerSniffer only tests conductor continuity and will not identify data integrity or capacity issues.
1.
2.
3.
4.
5.
6.
7.
Test and verify your CAT5e/CAT6 STP or UTP SCTLink™ cable for EIA568A/EIA568B.
The SCTLink™ cable must be between 10m (minimum) and 100m (maximum) length.
Connect one end of the SCTLink™ cable to the “SCTLink™” connection on the Head End module.
Connect the other end of your SCTLink™ cable to the provided PowerSniffer.
Connect the WPS-12 power supply to the Head End module.
Connect the WPS-12 power supply to AC mains.
If the SCTLink™ cable is properly terminated, it will display eight GREEN LEDs.
If you get any other result, stop and re-terminate cable.
Once your SCTLink™ cable has been tested, please disconnect the WPS-12 power supply from the Head End module,
and the PowerSniffer from the SCTLink™ cable, before proceeding to install.
INSTALL THE EXTENSION KIT
Connect the camera-end cables:
1.
Connect the RCC-C030 Y Cable between the RC4-CE Camera End module and Poly EagleEye IV.
• Connect the Mini-HDCI end to the EagleEye IV’s Mini-HDCI input.
• Connect the RJ45 branch of the Y Cable to the RC4-CE’s RJ45 input labeled “Power Control”.
• Connect the HDMI branch of the Y Cable to the RC4-CE’s HDMI input labeled “Video Input”.
Connect the codec-end cables:
2.
3.
4.
Connect the RCC-H030 Y Cable between the RC4-HE Head End module and the codec.
Caution: Please ensure the connector is right-side up as it can be easily inserted ‘upside down’.
• Connect the 9Pin branch of the Y Cable to the RC4-HE’s 9Pin input labeled “Control”.
• Connect the HDMI branch of the Y Cable to the RC4-HE’s HDMI input labeled “Video Out”.
Connect one end of your SCTLink™ cable to the RC4-HE module’s “SCTLink™” port.
• Connect the other end of your SCTLink™ cable to the RC4-CE module’s “SCTLink™” port.
Connect the WPS-12 power supply to the RC4-HE’s power input labeled “Power +30VDC”.
Installation Status - Refer to our modules’ LEDs for installation status.
For assistance troubleshooting INACTIVE LED statuses, please contact Tech Support at 203-854-5701.
MODULE
RC4-CE
RC4-HE
RC4-HE
LED LABEL
ACTIVE STATUS
INACTIVE STATUS
Camera Interface
Solid Green
Solid Red or Off
HDCP LEDSolid GreenOff
OK/LINK LED
Blinking Red > Green
Blinking Red
Cable Table - Part numbers, descriptions and functions of all SCT cables provided for the RC4-E4P™.
CABLEDESCRIPTIONFUNCTION
RCC-C030
1’ HDMI/RJ45 to Mini-HDCI Video/control connection between RC4-CE and camera.
RCC-H030
3’ HDMI/ DB9 to HDCI
Video/control connection between RC4-HE and codec.
Power Supply Specifications (AC-Mains Side)
Input Voltage: 100VAC to 240VAC 47Hz to 63Hz. Efficiency: 85% minimum. Turn-on Surge: Less than 60
amperes for a duration less than 1mS. Power Factor: 0.9 minimum (where applicable). 30VDC power supply
uses 1.45 amperes AC maximum. All specifications subject to change without notice.
TECH SUPPORT: 203-854-5701 • WWW.SOUNDCONTROL.NET • ©SOUND CONTROL TECHNOLOGIES, INC
">
