Advertisement
Advertisement
RemoteCam5-CST™ Installation Instructions DATE: 08/15/17 PRELIMINARY Thank you for choosing the Sound Control Technologies’ RemoteCam5™ camera integration kit! Included in each RC5-CST™ kit will be: 2 Power Supplies & cords (Currently all RemoteCam Kits utilize the WPS-12) to provide power for the RemoteCam5™ electronics as well as the SpeakerTrack up to 300’ from the head end. All the RemoteCam™ kits use the same power supply. The power supply is AC 100240V~47-63HZ compliant. 2 RemoteCam5™ Head End Modules (RC5-HE) which each provide system power, Ethernet control & two HDMI video outputs to the codec. 2 RemoteCam5™ Camera Modules with PowerSniffer™ (RC5-CE) that provide camera power, Ethernet Control and HDMI video input from the SpeakerTrack. Documentation Specific cables (P/N according to the following chart) Codec Camera SCT Kit C40, C60, C90 & SX80 SpeakerTrack 60 RC5-CST™ Cables 2 x RCC-C001, 1 x RCC-C002 2 x RCC-H001, 1 x RCC-H016 PPC-006 To proceed with the installation, insure that you have installed Two CAT5e or CAT6 cables between the camera installation site and the codec installation site. Minimum distance should be approximately 30’/9M.T www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2017 The cables must be wired for either UTP 568A or UTP 568B. Please use the following scheme. To install the RC5-CST™ Kit, follow this step-by-step guide: Step 1 Test and verify the Cat5e or Cat6 LINK cables for UTP 568A or 568B wiring: See steps 2 & 3. Step 2 Install the RC5-HE Head-End Modules at the rack/equipment location. Connect the Cat5e or Cat6 cable to the RJ45 connector labelled LINK on the RC5-HE modules. Connect the individual power supplies to the RC5-HE Modules. Wait to connect the LINK cable to the RC5-CE until steps 3 & 4 are completed. Step 3 At the camera location connect the PowerSniffer™ to the CAT5e or CAT6 LINK cable. If the LINK cable is properly terminated it will display 8 green LEDs. See image at left. Any other result, please re-terminate. Step 4 Disconnect the power supplies from the RC5-HE Modules Step 5 Connect the CAT5e or CAT6 cable to the RJ45 connector labelled LINK to the RC5-CE Camera Module. Step 6 Connect RCC-H001 HDMI cables between codec and RC5-HE module. Connect RCC-C016 Ethernet cable between codec and designated RC5-HE module. The codec (or second camera or touch panel) can connect to Port 1 or Port 2 of the RC5-HE. Step 7 Depending on the distance between the SpeakerTrack and RC5-CE modules, the use of SCT’s longer HDMI cables may be required. Connect RCC-C001 HDMI cables between SpeakerTrack and RC5-CE modules. Connect RCC-C002 Ethernet cable between SpeakerTrack and designated RC5-CE module. Connect PPC-006 Power cables between SpeakerTrack and RC5-CE modules. Step 8 Connect the power supplies to RC5-HE modules. It is recommended that both power supplies are on a single power strip for simultaneous power-up. LED Behavior: Head-End Module HDCP LED: Blinking = HDCP Inactive, Solid = HDCP Active Head-End Module LINK LED: Blinking Red = No Link, Blinking Red to Green = LINK Active Camera Module: LED will be Red until Link is established, Solid Green when LINK is Active Step 9 Enjoy! www.soundcontrol.net 203-854-5701 ©SOUND CONTROL TECHNOLOGIES, INC. 2017 ">

Public link updated
The public link to your chat has been updated.
Advertisement