THE TEMPLE CEILING FAN
INSTALLATION INSTRUCTIONS
Please read and save these instructions
These instructions are to be used in
the installation of the following
OXYGEN fans...
The Temple
© 2020 oxygen Lighting. All Rights Reserved.
201 Railhead Rd • Fort Worth, TX 76106 • (877) 607-0202 • FAX (877) 607-0203
IO303-12/01
OXYGEN'S UNIQUE LIMITED
LIFETIME WARRANTY
This warranty gives you specific legal
rights, and you may also have other rights
which vary from state to state.
WHAT IS COVEREDExcept as specified below, the manufacturer
of this product warrants it to be free of all
defects in workmanship and material.
WHAT IS NOT COVERED BY THIS
WARRANTY1. All costs of removal or reinstallation
of the fan.
2. Damage resulting from failure to
follow instructions contained herein.
3. Damage occurring during shipment of
the product (claims must be presented to
the carrier).
4. Damage resulting from accident,
misuse, abuse, or neglect.
5. Damage resulting from the application
of any exterior coating, or by the addition
of any unapproved accessories.
6. Damage resulting from repair or
attempted repair by anyone other than the
manufacturer.
technical skill, competence, or experience
of the user.
superior product if the defective unit is
returned prepaid to us.
8. Light bulbs, glass or acrylic
components or accessories.
TO GET WARRANTY SERVICE To obtain warranty service, the product
must be returned prepaid to Oxygen.
(This warranty is not enforceable outside
the United States.) Details regarding
return shipment are explained elsewhere
in this manual. Whenever warranty
service is required, you must present a
copy of the original dated sales receipt as
proof of coverage.
9. Minor occurrences of wobble are
accepted as normal and should not
necessarily be considered a defect.
WHO MAY ENFORCE WARRANTYThis warranty may be enforced only by
the original purchaser. The end user must
possess a dated proof of purchase from an
authorized Oxygen dealer to establish a
warranty claim.
LENGTH OF THE WARRANTY 1. For the fan motor - for the lifetime of
the original purchaser.
2. For everything else, except blades and
finish - one year from the date of
purchase.
3. For fan blades and finish - 90 days
from the date of purchase.
WHAT WE WILL PAY FOR We agree to correct defects outlined in the
warranty without charge, or at our option
replace the fan with an equivalent or
There is no other express warranty.
Oxygen hereby disclaims any and all
implied warranties, including but not
limited to those of merchantability of
fitness for a particular purpose to the
extent permitted by law. Oxygen shall not
be liable for incidental, consequential, or
special damages arising out of or in
connection with the product use or
performance except as may otherwise be
accorded by law. The duration of any
implied warranty which cannot be
disclaimed is limited to the periods
specified above in the express warranty.
7. Damage resulting from causes other
than product defects, including lack of
WARRANTY SERVICE
1. Most problems can be handled by our
customer service agents over the
telephone. Customers seeking warranty
repair or replacement for any fan or
component are encouraged to call us for
assistance. All returns must be issued a
Return Goods Authorization number
(RGA) prior to returning the defective
unit or part. Call (877) 607-0202 Monday thru Friday 8:00 a.m. - 5:00 p.m.
CST to obtain a RGA number.
2. Arriving shipments will be refused if
they do not bear a valid RGA number on
the outside packaging.
3. A dated proof of purchase must
accompany any fan or component clearly
indicating the name of the original
purchaser.
4. To avoid damage in transit, the
product should be returned in its original
box and packaging. Oxygen will not bear
responsibility for any shipping damage.
5. Any return of a fan or component
must be shipped freight and insurance
prepaid.
FOR YOUR RECORDS
Purchased From
City
State
Fan Model No.
Date Purchased
Complete and mail the enclosed
warranty card within 10 days to ensure
your warranty is registered.
If you have any questions regarding the
warranty, or the procedures for
obtaining service, please call us at
(877) 607-0202 - Monday thru Friday
8:00 a.m. - 5:00 p.m. CST.
1. SAFETY RULES
1. To avoid possible electric shock, turn
off the electricity at the main fuse box or
circuit panel before you begin the fan
installation or before servicing the fan or
installing accessories.
2. Read all instructions and safety
information carefully before installing
your fan and save these instructions.
3. Make sure all electrical connections
comply with local codes or ordinances as
well as the National Electrical Code. If
you are unfamiliar with electric wiring,
please use a qualified and licensed
electrician.
4. Make sure you have a location
selected for your fan which allows clear
space for the blades to rotate, and at lease
seven (7) feet of clearance between the
floor and the fan blade tips.
Model #3-115-XX: 16.87 lbs
5. The outlet box and ceiling support
joist used must be securely mounted, and
capable of supporting at least 35
pounds. To reduce the risk of fire,
electric shock, or personal injury, use only
an outlet box clearly labeled "Acceptable
for Fan Support of 15.9 kg (35 lbs) or
Less."
6. To reduce the risk of personal injury
use only approved hanging brackets and
screws supplied with the outlet box for
mounting to the outlet box.
7. After installation is complete, check
that all connections are absolutely secure.
10. Do not attempt to control the
operation of the fan (or an optional light
kit) from any wall control that is not
approved by Oxygen for use with its fans.
Do not use solid state wall controls. The
use of any unapproved control voids the
fan's warranty.
TOOLS REQUIRED
FOR INSTALLAITON
Phillips Screwdriver
Wire Cutters
Electrical Tape
Step Ladder
8. Do not insert anything into the fan
blades while they are rotating.
9. To operate the reverse function on the
fan, press the reverse button on the wall
transmitter while the fan is running.
2. UNPACKING YOUR FAN
Unpack your fan and check the contents. Do not discard the carton. If warranty
replacement or repair is ever necessary the fan should be returned in original packaging.
Remove all parts and hardware. Do not lay motor housing on its side - because the
decorative casing may shift. Check all visible screws, bolts and nuts for tightness.
Examine all parts. The following parts should be included:
1. Set of ABS blades (a)
2. Blade support plates (b)
3. Hanging bracket (c)
4. Canopy (d)
5. Canopy cover (e)
6. Downrod assembly (4") and Alternate downrod (6") (f)
7. Fan motor assembly (g)
8. Mounting plate (h)
9. 24W LED light kit (i)
10. Glass shade (j)
11. Parts bags (k) containing:
Blade attachment hardware
(Screws/lock washers)
Mounting hardware (wire nuts, wood screws, machine
screws, lock washers, spring washers, metal washers.)
Canopy cover
12. Receiver incl. 5 wire nuts (l)
13. Wall transmitter incl. 2 mounting screws and 3 wire nuts (m)
14. 2 wall plates (white and almond), 1 face plate (almond), 2
sets of mounting screws, and machine screws (n)
15. Battery (o)
16. Blade balancing kit (p)
NOTE:
Some Oxygen fan models will have slightly
different parts than what is shown here
depending upon the design you have chosen.
Basic installation procedures are similar for
all models.
e.
a.
f.
g.
k.
l.
m.
n.
h.
b.
c.
d.
i.
j.
o.
p.
IF YOU FIND THAT PARTS ARE MISSING. CONTACT YOUR DEALER FOR REPLACEMENT, OR CALL OXYGEN DIRECTLY AND WE WILL MAIL REPLACEMENTS TO YOU IMMEDIATELY.
3. MOUNTING OPTIONS
1. Disconnect the power by removing fuses
or turning off circuit breakers.
2. If there is an existing outlet box, ensure it
is clearly marked "Acceptable for Fan Support
of 15.9 kg (35 lbs) or Less". If it is not so
marked, it must be replaced with an approved
one.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, OR PERSONAL INJURY,
MOUNT THE FAN ONLY TO AN OUTLET MARKED ACCEPTABLE FOR FAN SUPPORT AND
USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.
Fig. 1
3. Secure the outlet box (or make sure the
existing box is secured) directly to the building
structure. Use appropriate fasteners and building
materials.
4. Figures 1,2 and 3 are examples of different
ways to mount the outlet box in different
situations. A longer downrod may be required
in sloped ceiling situations to maintain proper
blade clearance.
Fig. 2
Ceiling Joists
Outlet Boxes
Fig. 3
Outlet Boxes
Fig. 4
Ceiling Joists
Ceiling Joist
5. To hang the fan in locations where no
ceiling joist is available, a hanger support bar
may be required (Figure 3). Contact your local
dealer for support bars and outlet boxes.
Recessed
outlet Boxes
Ceiling Joists
Angled ceiling
maximum 15º
angle with 4" and
6" downrod
(23º Max. slope
with optional
extension rod)
Hanger
Support Bar
Ceiling Joist
Outlet Boxes
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, INSTALL THE PRIMARY MOUNTING MEANS AND USE ONLY THE HARDWARE
PROVIDED WITH THE FAN.
4. HANGING YOUR FAN
WARNING - Turn off the power!
DO NOT fasten the blades to the fan until it
is assembled and hanging from the ceiling.
To do so now will likely bend the blade arms
and almost certainly cause wobble.
1. If not already affixed to the hanger
bracket, place the rectangular rubber
isolators between the hanger bracket and
outlet box. Secure the hanger bracket to
the outlet box using the 2 long steel screws
supplied with the outlex box. (Fig. 5)
Fig. 5
Fig. 6
Metal
washer
Screws
Outlet box
Hanger
bracket
Washers
Motor
upper
cover
Screws
2. Take out the six screws in the fan
motor and remove the motor upper cover
and metal washer. (Fig. 6)
Fan
Motor
4. HANGING YOUR FAN (continued)
3. Take out the set screw located in the
hanger ball, lower the hanger ball and
remove the cross pin. Remove the hanger
ball from the hanger ball/downrod assembly
(Fig. 7).
4. Remove the set pin, safety lock clip and
set screws from the yoke on top of the motor
assembly. (Fig. 8)
5. Feed the wires from the fan motor
through the downrod. Align the holes at
the bottom of the downrod with the holes
in the collar on top of the motor housing.
Carefully insert the set pin through the
holes in the collar and downrod. Be careful
not to jam the pin against the wiring inside
the downrod. Insert the safety lock clip
through the hole near the end of the set pin
until it snaps into its locked position. (Fig. 8)
6. Tighten the two set screws on top of
the fan motor firmly. (Fig. 8)
7. Place the motor upper cover and the
metal washer onto downrod. Secure by
tightening the six screws previously
removed. (Fig. 8)
8. Attach the canopy cover and canopy
onto the downrod. Carefully reinstall the
hanger ball, being sure that the cross pin
is in the correct position, the set screw is
tightened and wires are not twisted. (Fig. 9)
NOTE: If a longer downrod (not included)
is needed, take out the screw located in the
hanger ball, lower the hanger ball and
remove the pin. Remove all two pieces
from the downrod and assemble them onto
the new longer downrod before proceeding
to the downrod installation.
9. Lift the fan motor place into the hanger
bracket, rotating the ball until the groove
engages the tab on the hanger bracket.
This locks the ball mount and fan motor,
preventing fan rotation during operation.
(Fig. 10)
10. Secure the safety cable to the building
structure using a wood screw (not included).
(Fig. 10)
Fig. 7
Fig. 9
Hanger ball
Set screw
Hanger
ball
Cross pin
Downrod
Set screw
Canopy
Canopy cover
Fig. 8
Metal
washer
Cross pin
Screws
Downrod
Motor
upper
cover
Downrod
Set screw
Set pin
Yoke
Fig. 10
Safety
lock clip
Safety cable
Hanger bracket
Downrod
5. ELECTRICAL CONNECTIONS
REMEMBER -Turn off the power! NOTE - Control must be installed within 30 feet of fan.
4. Put the receiver unit inside the canopy.
Proceed to Step 6 - Completing the
Installation.
Remove the existing wall plate and
switch from the wall junction box.
Connect one BLACK wire from the
wall to one BLACK wire (labeled "TO
FAN") from the wall transmitter.
Connect the other BLACK wire
(labeled "TO POWER SUPPLY")
from the transmitter to the remaining
BLACK wire from the wall (A/C
supply source).
WH
BLK
House
supply
wire
Connect the BLACK building
supply wire to the BLACK receiver
wire.
Connect the WHITE receiver neutral
wire to the WHITE building neutral wire.
Connect the COPPER building
ground wire to the YELLOW/GREEN
fan ground wire. Also connect the two
GREEN wires (from fan) to building
ground wire.
3. Connect the wiring from the wall
switch receptacle to wall transmitter unit.
GROUND
Fig. 11
BLK
Outlet box
WH
2. Connect the wiring from the ceiling to
the receiver unit. (Use the 2 wire bundle
on the receiver.) Secure with supplied wire
nuts.
Carefully tuck the connected wires inside
the junction box. Secure the transmitter
with the two screws provided. Attach the
face plate over the transmitter with the two
screws provided.
YELLOW/GRN
GRN
GRN
Connect the YELLOW fan wire to
the YELLOW receiver wire.
Connect the GRAY fan wire to the
GRAY receiver wire.
Connect the RED fan wire to the
RED receiver wire.
Connect the WHITE fan wire to the
WHITE receiver wire.
Connect the BLUE fan wire to the
BLUE receiver wire.
Use ONLY wall controls approved by
Quorum. Use of unapproved wall
controls will cause unacceptable
humming noise, and avoids the fan
warranty.
Ceiling
Receiver
Wall control
YELLOW
GRAY
RED
WHITE
BLUE
1. Make wire connections from the fan
to the wall control receiver unit. For this
step use the bundle of 5 wires on the
receiver. (Fig. 11)
If your junction box has a ground wire
(green or bare copper), connect the
transmitter's ground wire to it. Otherwise,
connect the transmitter ground wire
directly to one of the screws from the
outlet box.
BLK
Use the wire nuts supplied with your fan
when making connections. Secure the
connectors with electrical tape and make
sure there are no loose connections or wire
strands.
GRN (downrod)
GRN (hanger bracket)
Fan canopy
6. COMPLETING THE INSTALLATION
1. Make sure the wiring is safely inside the
outlet box as instructed in Step 5 Electrical Connections. To install the
canopy, slide the canopy up to hanger
bracket and place the key hole on the
canopy over the screw on the hanger
bracket, turn canopy until it locks in place
at the narrow section of the key holes. (Fig.
10) Align the circular hole on canopy with
the remaining hole on the hanger bracket,
secure by tightening the two set screws, lift
canopy cover and attach by turning
clockwise. Note: Adjust the canopy screws
as necessary until the canopy and canopy
cover are snug. (Fig. 12)
2. Blade Assembly & Installation (Fig. 13)
Insert blade through one of the slots from
the motor housing. Align holes from blade,
blade support plates and motor housing and
secure with blade attachment screw. Repeat
steps for the remaining blades. DO NOT
bend the blade arms when installing the
blades.
Fig. 15
Fig. 12
Outlet box
Hanger
bracket
Screws
Canopy
Screws
Canopy cover
Wiring plug
Fig. 13
24W LED
light kit
Screws
Fig. 16
3. Attaching the Mounting Plate (Fig. 14)
Attach the mounting plate to the flange of
the motor by using the three screws
provided that are pre-installed on the flange.
4. Attaching the LED Light Kit (Fig. 15)
Connect the two wiring plugs from the
motor assembly to the corresponding plugs
in the light kit. Attach the light kit to the
mounting plate by using the three screws
provided that are preinstalled on the
mounting plate.
Mounting
plate
Blades
Blade
support
plates
Screws
Fig. 14
Glass shade
5. Attaching the glass shade (Fig.16)
Raise glass shade up against mounting plate
secure it to the fan by turning clockwise until
snug.provided. DO NOT OVER TIGHTEN.
A certain amount of wobble may be
considered normal, especially if the fan is
on a downrod long than 12".
Flange
Mounting
plate
Screws
24W LED light kit
7. INSTALLING THE WALL CONTROL
REMEMBER -Turn off the power! NOTE - Control must be installed within 30 feet of fan.
1. Remove the existing wall plate and
switch from the wall junction box.
2. If your outlet box has a ground wire
(green or bare copper) connect the wall
control's ground wire to it; otherwise
connect the wall control's ground wire
directly to one of the screws from the
outlet box.
3. (Fig. 17) Carefully tuck the wire
connections inside the junction box.
Secure the wall control with the two
screws provided. Attach the wall plate
over the wall control and secure with the
two screws provided.
Fig. 17
8. OPERATING YOUR TRANSMITTER
Your DC brushless motor is equipped with
an automatically learned type remote
control. There is no frequency switches on
the receiver or transmitter. The fan can
start to use once the pairing process is
done.
Remove the panel from the transmitter and
then install one 23A/12V battery
(included). To prevent damage to
transmitter, remove the battery if not use
for long periods of time (Fig. 19).
A. 1, 2, 3, 4, 5 and 6 buttons:
These six buttons are used to set the
fan speed as follows:
1 = minimum speed
2 = low speed
3 = medium low speed
4 = medium speed
5 = medium high speed
6 = high speed
E. "D" and "ON" dip switch:
The "ON" selection is the light
dimmable selection and is to be used
with all bulbs execpt for CFL bulbs.
The "D" selection is the light on only
(no dimmable function) and is to be
used with CFL and LED bulbs as
CFL bulbs cannot be dimmed
properly.
Fig. 18
F. "SET" code setting button:
Follow the below steps to use the set
button. (Fig. 18)
G. ON - OFF Slide button: Power
switch. (Fig. 18)
Fig. 19
H. Signal light (Fig. 19)
Pairing Process
B.
button:
This button turns the fan off.
C.
Reverse button:
This button is to control fan direction.
This button must be pressed while fan
is running (suggested speed 4)
With the fan’s power off, restore power to
the fan. Press and hold “SET” button for
about 5 seconds and release. If optional
light kit is installed, the light kit will flash
twice and the signal light on the wall
control will come on when the button is
pressed. The fan has completed the
pairing process with the wall control and
is ready for use.
D.
Light button:
This button is to control optional light.
Switch the "D" and "ON" dip switch
on the front of transmitter to decide the
light in "ON/OFF" or "Dimmable"
condition.
NOTE: A single fan can be controlled
with as many as 3 wall controls in one
room. Every control will need to repeat
the pairing process based on instructions
above and all controls must be within 30
feet of the fan.
Signal light
Power switch
8. OPERATING YOUR TRANSMITTER (continued)
NOTE: If multiple fans are installed on
the same circuit, each fan must have it’s
own switch leg. Each fan and wall
control pair must have its own wire from
the control to the fan(the wire from the
control to the fan can NOT be shared).
There can NOT be a jumper wire running
from fan to fan.
NOTE: The ”SET” button must be
pressed within 60 seconds of restoring
power.
The receiver provides the following
protective function:
1. Lock position: The DC motor has a
built-in safety against obstruction during
operation. The motor will be locked
operation and disconnect power after 30
seconds of interruption. Please remove
obstacles before re-set.
2. Over 80W protection: When the
receiver detects motor power
consumption which is greater than 80W,
the receiver power will be stopped and
operation will immediately discontinue.
Turn the receiver power on after 5
seconds.
9. FAN OPERATION AND CARE
1. A ceiling fan is an environmentally
smart choice to cool as well as to help
warm your home or office. Adjust your
HVAC thermostat during fan use to save
additional energy and money on your air
conditioning and heating utility bills. You
should see a significant reduction in both
your heating and cooling costs by regular
use of your fan.
Do not hesitate to use your fan during
summer and winter months. In summer,
(Fig. 20) using the reverse switch, adjust
the fan's direction so cool air is blown
down, producing a cooling breeze. In
winter, (Fig. 21) reverse the fan so that an
upward airflow will push warm air off the
ceiling and circulate it downwards into the
living area. In winter months, use the fan
at a lower speed than summer.
2. Periodically check tightness of all
screws securing the blades to the blade
arm attachment points. A clicking or a
rattling noise is a sure indication of
loosening screws. Since screws will
invariably work loose over time, at least
once a year, tighten all the screws
attaching blades to blade arms. Do not
bend blade arms when cleaning or
servicing the fan.
3. Clean you fan periodically using only
a cloth dampened with a mild detergent
solution for all hardware - never use
solvents. The finish plating is lacquered
to prevent tarnishing. Use a lint-free cloth
with clean water to clean blades.
Fig. 20
4. You will never need to oil or lubricate
your fan. Its permanently sealed bearings
will provide trouble free, silent operation
for many years.
5. If repairs or servicing are ever
required, to avoid possible electric shock,
turn off the electricity at the main fuse
or circuit panel before you begin.
Fig. 21
WINTER
10. TROUBLESHOOTING
FAN WILL NOT START
1. Check that the electricity has been
turned on at the circuit breaker which had
probably been turned off during
installation.
2. Turn off the electricity. Check all
connections in the wiring of the fan at the
ceiling and make sure it follows the
wiring instructions outlined in this
manual.
3. Be sure ON/OFF power switch on the
wall control is in ON position.
4. Be sure the wall control is installed
within 30 feet of ceiling fan.
NOISE
Note: Always allow a day or two "run-in"
time for any new fan at medium or high
speed. When attempting to diagnose
noise, listen carefully from several sides
to try and isolate the location of the noise
(blade, upper end, motor, light kit, etc.)
1. Tighten all screws attaching blades to
blade arms. Remember to tighten these
screws at least once a year because they
may loosen slowly over time and cause a
clicking noise.
2. Turn off the power. Loosen the
canopy and check that the wiring and/or
wire nut connectors are not resting against
the canopy, possibly vibrating while the
fan is on.
3. Use of a standard light rheostat or an
unapproved fan wall control to control the
fan speed will always cause an annoying
"hum". Many fan motors do not work
quietly with solid state variable speed
controls.
4. Check that the rubber gasket on the
mounting bracket has been installed if
called for in the installation instructions.
5. Check that the canopy in not touching
the ceiling.
6. Check that all screws on the motor
housing and the bottom housing are tight.
FAN TURNS, BUT DOES NOT MOVE
MUCH AIR
1. The fan may be running in reverse.
Press the reverse button on transmitter to
set the fan in forward operation.
2. The distance from the ceiling to the
blades may be too small. For downrod
fans, optimal placement would be 8-9 feet
from the floor.
3. The room may contain items which
obstruct the air flow.
4. The fan may be too small for the size
of the room.
EXCESSIVE WOBBLE
Note: A small amount of wobble is
considered acceptable and should not be
considered a defect.
1. Make certain all blades are tightly
attached to each blades' respective blade
arm.
REPLACEMENT PARTS
For replacement parts, contact your
local dealer.
">
