Oxygen 3-113-xx Dynamo Instructions

THE DYNAMO CEILING FAN
INSTALLATION INSTRUCTIONS
Please read and save these instructions
These instructions are to be used in
the installation of the following
OXYGEN fans...
The Dynamo
© 2020 oxygen Lighting. All Rights Reserved.
201 Railhead Rd • Fort Worth, TX 76106 • (877) 607-0202 • FAX (877) 607-0203
IO297-05/15
1. SAFETY RULES
1. To avoid possible electric shock, turn
off the electricity at the main fuse box or
circuit panel before you begin the fan
installation or before servicing the fan or
installing accessories.
2. Read all instructions and safety
information carefully before installing
your fan and save these instructions.
3. Make sure all electrical connections
comply with local codes or ordinances as
well as the National Electrical Code. If
you are unfamiliar with electric wiring,
please use a qualified and licensed
electrician.
4. Make sure you have a location
selected for your fan which allows clear
space for the blades to rotate, and at lease
seven (7) feet of clearance between the
floor and the fan blade tips.
Model #3-113-xx: 13.69 lbs
5. The outlet box and ceiling support
joist used must be securely mounted, and
capable of supporting at least 35 pounds.
To reduce the risk of fire, electric shock,
or personal injury, use only an outlet box
clearly labeled "Acceptable For Fan
Support".
9. Do not attempt to control the
operation of the fan (or an optional light
kit) from any wall control that is not
approved by Oxygen for use with its fans.
Do not use solid state wall controls. The
use of any unapproved control voids the
fan's warranty.
6. To reduce the risk of personal injury
use only approved hanging brackets and
screws supplied with the outlet box for
mounting to the outlet box.
TOOLS REQUIRED
FOR INSTALLAITON
7. After installation is complete, check
that all connections are absolutely secure.
Phillips Screwdriver
Wire Cutters
Electrical Tape
Step Ladder
8. Do not insert anything into the fan
blades while they are rotating.
2. UNPACKING YOUR FAN
Unpack your fan and check the contents. Do not discard the carton. If warranty
replacement or repair is ever necessary the fan should be returned in original packaging.
Remove all parts and hardware. Do not lay motor housing on its side - because the
decorative casing may shift. Check all visible screws, bolts and nuts for tightness.
Examine all parts. The following parts should be included:
1. Set of blades (a)
2. Blade holder (b)
3. Hanging bracket (c)
4. Ceiling canopy (d)
5. Canopy cover (e)
6. Downrod assembly (4") and Alternate
downrod (6") (f)
7. Yoke cover (g)
8. Fan motor assembly (h)
9. Receiver incl. 5 wire nuts (i)
10. Transmitter incl. 3V (CR2032) battery, 2 mounting
screws and holder (j)
11. Parts bags (k) containing:
Blade attachment hardware
(Screws/washers, washers may be attached to screws)
Blade holder attachment hardware
(Screws/washers, washers may be attached to screws)
Mounting hardware (wire nuts, wood screws,
machine screws, lock washers, spring washers, metal
washers.)
12. Blade balancing kit (l)
a.
NOTE:
Some Oxygen fan models will have slightly
different parts than what is shown here
depending upon the design you have chosen.
Basic installation procedures are similar for
all models.
d.
i.
e.
j.
6
5
4
3
2
1
0
f.
g.
k.
l.
b.
h.
c.
IF YOU FIND THAT PARTS ARE MISSING. CONTACT YOUR DEALER FOR REPLACEMENT, OR CALL OXYGEN DIRECTLY AND WE WILL MAIL REPLACEMENTS TO YOU IMMEDIATELY.
3. MOUNTING OPTIONS
1. Disconnect the power by removing fuses
or turning off circuit breakers.
2. If there is an existing outlet box, ensure it
is clearly marked "Acceptable for Fan
Support of 15.9 kg (35 lbs) or Less". If it is
not so marked, it must be replaced with an
approved one.
3. Secure the outlet box (or make sure the
existing box is secured) directly to the
building structure. Use appropriate fasteners
and building materials.
4. Figures 1,2 and 3 are examples of
different ways to mount the outlet box in
different situations. A longer downrod may
be required in sloped ceiling situations to
maintain proper blade clearance.
5. To hang the fan in locations where no
ceiling joist is available, a hanger support bar
may be required (Figure 4). Hanger support
bars are available at most area home centers.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, FIRE, OR PERSONAL INJURY,
MOUNT THE FAN ONLY TO AN OUTLET MARKED ACCEPTABLE FOR FAN SUPPORT AND USE
MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.
Fig. 1
Fig. 2
Ceiling Joists
Outlet Boxes
Outlet Boxes
Fig. 3 Ceiling Joists
Fig. 4
Ceiling Joist
Recessed
outlet Boxes
Ceiling Joists
Angled ceiling
maximum 15º
angle with 4"
downrod
(23º Max. slope
with optional
extension rod)
Hanger
Support Bar
Ceiling Joist
Outlet Boxes
CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, INSTALL THE PRIMARY MOUNTING MEANS AND USE ONLY THE HARDWARE
PROVIDED WITH THE FAN.
4. HANGING YOUR FAN
WARNING -Turn off the power!
1. Remove the motor housing cover and
metal washer by removing the six screws
from the top of the motor housing. (Fig. 5)
Fig. 5
Fig. 8
Screws
Screws
Metal
washer
2. Attach the blades to the blade holder
with the screws and rubber washers.
Ensure all screws are used for each blade.
(Fig. 6)
Metal
washer
Motor
housing
Motor
housing
3. Attach the blade holder assembly to the
motor assembly using the supplied screws.
DO NOT bend the blade when installing
the blades. (Fig. 7)
Yoke
4. Place the motor housing over the
motor. Align the mounting holes with the
holes in the motor and fasten using the six
screws with lock washers and metal
washer previously removed. (Fig. 8)
5. Attach hanging bracket to outlet box
using screws and washers provided with
the outlet box. (Fig. 9)
Yoke
Motor
Motor
assembly
Fig. 6
Screws with
fiber washers
Blade
holder
Fig. 9
Ceiling Fan
Outlet Box
Blades
Fig. 7
Hanger
Bracket
Flat Washer
Spring Washer
Outlet Box
Screw
Motor
Screws with
lock washers
Blade holder
assembly
5. HANGING YOUR FAN
WARNING -Turn off the power!
Fig. 10
Fig. 12
DO NOT fasten the blades to the fan
until it is assembled and hanging from
the ceiling. To do so now will likely
bend the blade arms and almost
certainly cause wobble.
Downrod
assembly
Hanger bracket
Ceiling
canopy
1. If not already affixed to the hanger
bracket, place the rectangular rubber
isolators between the hanger bracket and
outlet box. Secure the hanger bracket to
the outlet box using the 2 long steel
screws supplied with the outlex box.
2. Remove the set pin and safety lock
clip from the yoke on top of the motor
assembly. Slide the downrod through the
canopy and canopy cover. Slide the yoke
cover onto the downrod (Fig. 10). Feed
the wires from the fan motor through the
downrod assembly.
3. (Fig. 11) Attach the downrod
assembly (downrod, yoke cover, canopy
and canopy cover) to the motor by sliding
the downrod into the yoke on top of the
motor assembly. Slide the set pin through
the hole in the yoke, downrod and secure
it with the safety lock clip. Tighten the
set screws on yoke. The yoke cover will
lower down to conceal the yoke. Feed the
wires through the downrod ball.
4. Lift the fan motor without the blades
and place into the hanger bracket, rotating
the ball until the groove engages the tab
on the hanger bracket. This locks the ball
mount and fan motor, preventing fan
rotation during operation. (Fig. 12)
Safety cable
Downrod
Canopy
cover
Yoke cover
Fig. 11
Downrod
Canopy
Canopy cover
Yoke cover
Yoke
Set pin
Set screw
Safety
lock clip
6. ELECTRICAL CONNECTIONS
REMEMBER -Turn off the power! NOTE - Control must be installed within 30 feet of fan.
GROUND
WH
BLK
House
supply
wire
Outlet box
YELLOW/GRN
GRN
GRN
Connect the BLACK building
supply wire to the BLACK receiver
wire.
Connect the WHITE receiver neutral
wire to the WHITE building neutral wire.
Connect the COPPER building
ground wire to the YELLOW/GREEN
fan ground wire. Also connect the two
GREEN wires (from fan) to building
ground wire.
Fig. 13
WH
2. Connect the wiring from the ceiling to
the receiver unit. (Use the 2 wire bundle
on the receiver.) Secure with supplied wire
nuts.
4. Put the receiver unit inside the canopy.
Proceed to Step 7 - Completing the
Installation.
BLK
Connect the YELLOW fan wire to
the YELLOW receiver wire.
Connect the GRAY fan wire to the
GRAY receiver wire.
Connect the RED fan wire to the
RED receiver wire.
Use ONLY wall controls approved by
Oxygen. Use of unapproved wall
controls will cause unacceptable
humming noise, and avoids the fan
warranty.
Carefully tuck the connected wires inside
the junction box. Secure the transmitter
with the two screws provided. Attach the
face plate over the transmitter with the two
screws provided.
Ceiling
Receiver
GRAY
RED
1. Make wire connections from the fan
to the wall control receiver unit. For this
step use the bundle of 3 wires on the
receiver. (Fig. 13)
If your junction box has a ground wire
(green or bare copper), connect the
transmitter's ground wire to it. Otherwise,
connect the transmitter ground wire
directly to one of the screws from the
outlet box.
YELLOW
Use the wire nuts supplied with your fan
when making connections. Secure the
connectors with electrical tape and make
sure there are no loose connections or wire
strands.
GRN (downrod)
GRN (hanger bracket)
Fan canopy
7. COMPLETING THE INSTALLATION
1. Make sure the wiring is safely inside the outlet box as instructed in Step 6 Electrical Connections. To install the canopy, slide the canopy up to hanger bracket
and place the key hole on the canopy over the screw on the hanger bracket, turn canopy
until it locks in place at the narrow section of the key holes. (Fig. 14) Align the circular
hole on canopy with the remaining hole on the hanger bracket, secure by tightening the
two set screws, lift canopy cover and attach by turning clockwise. Note: Adjust the
canopy screws as necessary until the canopy and canopy cover are snug.
Fig. 14
Outlet box
Hanger
bracket
Screws
Canopy
Screws
Canopy cover
8. INSTALLING THE BATTERY
Warning: Chemical Burn Hazard.
Keep batteries away from children.
This product contains a lithium button/coin
cell battery. If a new or used lithium
button/coin cell battery is swallowed or
enters the body, it can cause severe internal
burns and can lead to death in as little as 2
hours. Always completely secure the
battery compartment. If the battery
compartment does not close securely, stop
using the product, remove the batteries, and
keep it away from children. IF you think
batteries might have been swallowed or
placed inside any part of the body, seek
immediate medical attention.
The batteries shall be disposed of properly,
including keeping them away from
children; Even used cells may cause injury.
Remove the set screw on the back of
transmitter, take out the battery cover.
Insert the 3 volt battery (included) and
make sure they are seated correctly in each
recess with the Positive + sign facing up.
When remove or insert the batteries, use a
suitable screwdriver to loosen or tighten
the screws and open the back cover. (Fig.
15)
Fig. 15
Set screw
8. OPERATING YOUR TRANSMITTER
Your DC brushless motor is equipped with
an automatically learned type remote
control. There is no frequency switches on
the receiver or transmitter. The fan can
start to use once the pairing process is
done.
Operation Instructions
A. 1, 2, 3, 4, 5 and 6 buttons:
These six buttons are used to set the fan
speed as follows:
1= minimum speed
2= low speed
3= medium low speed
4= medium speed
5= medium high speed
6= high speed
B. button:
This button turns the fan off.
C. The "
" button is used to set the
fan forward or reverse, press the button
forward (for warm weather) or reverse (for
cool weather).
NOTE: To operate the reverse function on
this fan, press the reverse button while the
fan is running.
Pairing Process
With the fan’s power off, restore power to
the fan. Press and hold “ ” button for
about 5 seconds and release. If optional
light kit is installed, the light kit will flash
twice and the signal light on the remote
control will come on when the button is
pressed. The fan has completed the pairing
process with the remote control and is
ready for use.
NOTE: A single fan can be controlled
with as many as 3 remote controls in one
room. Every control will need to repeat
the pairing process based on instructions
above and all controls must be within 30
feet of the fan.
If a room has two fans installed, each fan
will need it’s own remote control. A
single control CAN NOT control more
than one fan. Each fan will need to go
through the pairing process individually.
While running the pairing process on the
first fan, turn power off to the second fan.
When finished the pairing process for the
first fan, turn the power off and restore
power to the second fan and run the
pairing process- NOTE the " " button
must be pressed within 60 seconds of
restoring power to the second fan.
Fig. 16
1. Lock position: The DC motor has a
built-in safety against obstruction during
operation. The motor will be locked
operation and disconnect power after 30
seconds of interruption. Please remove
obstacles before re-set.
2. Over 80W protection: When the
receiver detects motor power
consumption which is greater than 80W,
the receiver power will be stopped and
operation will immediately discontinue.
Turn the receiver power on after 5
seconds.
5
4
3
2
1
0
NOTE: If multiple fans are installed on
the same circuit, each fan must have it’s
own switch leg. Each fan and remote
control pair must have its own wire from
the control to the fan (the wire from the
control to the fan can NOT be shared).
There can NOT be a jumper wire running
from fan to fan.
The receiver provides the following
protective function:
6
Fig. 17
9. FAN OPERATION AND CARE
1. A ceiling fan is an environmentally
smart choice to cool as well as to help
warm your home or office. Adjust your
HVAC thermostat during fan use to save
additional energy and money on your air
conditioning and heating utility bills. You
should see a significant reduction in both
your heating and cooling costs by regular
use of your fan.
Do not hesitate to use your fan during
summer and winter months. In summer,
(Fig. 18) using the reverse switch, adjust
the fan's direction so cool air is blown
down, producing a cooling breeze. In
winter, (Fig. 19) reverse the fan so that an
upward airflow will push warm air off the
ceiling and circulate it downwards into the
living area. In winter months, use the fan
at a lower speed than summer.
2. Periodically check tightness of all
screws securing the blades to the blade
arm attachment points. A clicking or a
rattling noise is a sure indication of
loosening screws. Since screws will
invariably work loose over time, at least
once a year, tighten all the screws
attaching blades to blade arms. Do not
bend blade arms when cleaning or
servicing the fan.
3. Clean you fan periodically using only
a cloth dampened with a mild detergent
solution for all hardware - never use
solvents. The finish plating is lacquered to
prevent tarnishing. Use a lint-free cloth
with clean water to clean blades.
Fig. 18
4. You will never need to oil or lubricate
your fan. Its permanently sealed bearings
will provide trouble free, silent operation
for many years.
5. If repairs or servicing are ever
required, to avoid possible electric shock,
turn off the electricity at the main fuse
or circuit panel before you begin.
Fig. 19
WINTER
10. TROUBLESHOOTING
FAN WILL NOT START
1. Check that the electricity has been
turned on at the circuit breaker which had
probably been turned off during
installation.
2. Turn off the electricity. Check all
connections in the wiring of the fan at the
ceiling and make sure it follows the
wiring instructions outlined in this
manual.
3. Be sure ON/OFF power switch on the
wall control is in ON position.
4. Be sure the wall control is installed
within 30 feet of ceiling fan.
NOISE
Note: Always allow a day or two "run-in"
time for any new fan at medium or high
speed. When attempting to diagnose
noise, listen carefully from several sides
to try and isolate the location of the noise
(blade, upper end, motor, light kit, etc.)
1. Tighten all screws attaching blades to
blade arms. Remember to tighten these
screws at least once a year because they
may loosen slowly over time and cause a
clicking noise.
2. Turn off the power. Loosen the canopy
and check that the wiring and/or wire nut
connectors are not resting against the
canopy, possibly vibrating while the fan is
on.
3. Use of a standard light rheostat or an
unapproved fan wall control to control the
fan speed will always cause an annoying
"hum". Many fan motors do not work
quietly with solid state variable speed
controls.
4. Check that the rubber gasket on the
mounting bracket has been installed if
called for in the installation instructions.
EXCESSIVE WOBBLE
Note: A small amount of wobble is
considered acceptable and should not be
considered a defect.
1. Make certain all blades are tightly
attached to each blades' respective blade
arm.
REPLACEMENT PARTS
5. Check that the canopy in not touching
the ceiling.
6. Check that all screws on the motor
housing and the bottom housing are tight.
FAN TURNS, BUT DOES NOT MOVE
MUCH AIR
1. The fan may be running in reverse.
Press the reverse button on transmitter to
set the fan in forward operation.
2. The distance from the ceiling to the
blades may be too small. For downrod
fans, optimal placement would be 8-9 feet
from the floor.
3. The room may contain items which
obstruct the air flow.
4. The fan may be too small for the size
of the room.
For replacement parts, contact your
local dealer.
">