User’s Manual
PiXORD H.264 Series
2-Megapixel Network Camera
PD614/PD614E
Version 1.1
Date: 10/24/2011
Content
Notices ........................................................................................................................... 3
Introduction .................................................................................................................... 5
Installation...................................................................................................................... 6
1. Hardware ............................................................................................................ 6
2. Software Installation .......................................................................................... 7
3. Network Configuration ...................................................................................... 8
Access to the Camera ................................................................................................... 12
Video and Image Configuration ................................................................................... 14
Video .................................................................................................................... 14
Camera ................................................................................................................. 20
Event Handling .................................................................................................... 22
Local Storage and Schedule Recording ............................................................... 26
Network Configuration ........................................................................................ 28
System Options .................................................................................................... 31
Web Interface Customization ............................................................................... 34
Troubleshooting ........................................................................................................... 36
Check firmware version ....................................................................................... 36
Upgrade device firmware ..................................................................................... 37
Restore Factory Default Settings ......................................................................... 38
Video Streams Specification ................................................................................ 39
Notices
This user manual is intended for administrators and users of the PiXORD PD614 Series
Network Camera, including instructions for using and managing the camera on your network.
The use of surveillance devices may be prohibited by law in your country. It is the user’s
responsibility to ensure that the operation of such devices is legal before installing this unit for
its intended use.
Before the Network Camera is installed, all the safety and operating instructions should be
carefully read and followed to avoid damage due to faulty assembly and installation. This also
ensures the product is used properly as intended.
Heed all warnings
Do not drop or strike this equipment
Sensitive electronics inside the camera are vulnerable to excessive strike.
Do not install the equipment near any flames or heat sources
Excessive heat could damage this equipment.
Do not cover cloth or to install this equipment in poorly ventilated places.
Overheating could damage this equipment.
Do not expose this equipment to rain or moisture. Do not touch the power
connection with wet hands
Risk of short circuit, electric shock or fire
Do not damage the power cord or leave it under pressure
Risk of fire or shock circuit
To reduce the risk of electric shock, do not remove the Cover (or Back).
No user-serviceable parts inside. Misusage, improper, and negligence could
damage this equipment. Need to refer servicing to qualified service personnel.
Do not continue to operate if there appears to be fault.
If the unit ceases to function, contact qualified service personnel for help.
All work related to the installation of this product should be made by qualified
service personnel or system installers.
Liability
PiXORD Corporation reserves the right to make corrections, modifications, enhancements,
improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information
before placing orders and should verify that such information is current and complete. All
3
products are sold subject to PiXORD Corporation’s terms and conditions of sale supplied at
the time of order acknowledgment.
PiXORD is not responsible or liable for the resale of its products with statements different from
or beyond the specification/parameters stated by PiXORD. Customers are responsible for their
applications using PiXORD products. To minimize the risks associated with customer
applications, customers should provide adequate operating safeguards. PiXORD is under no
obligation to provide any further technical support service or product/software alteration
beyond PiXORD's representation.
PiXORD products are not authorized for use in safety-critical applications where a failure of the
PiXORD product would cause severe personal injury or death, unless officers of the parties
have executed an agreement specifically governing such use.
Reproduction of PiXORD information or datasheets with alteration is an unfair and deceptive
business practice. PiXORD is not responsible or liable for any such statements.
Every care has been taken of this manual. If there are any inaccuracies or omissions, please
inform your local office. PiXORD Corporation cannot be held responsible for any typographical
or technical errors. PiXORD Corporation is not liable or responsible for incidental or damages
caused by mishandling.
Trademarks
All names used in this manual for hardware and software are probably registered trademarks
of respective companies. PiXORD is a registered trademark of PiXORD Corporation. All rights
reserved.
Support
If you require any technical assistance, please contact your PiXORD reseller. You can connect
to the Internet PiXORD’s website: www.pixord.com for below information,
Download user documentation and firmware updates at PiXORD Support
( http://www.pixord.com/support/support.asp)
Find answers to resolved problems in the FAQ database. Or contact our FAE at technical
support (http://www.pixord.com/contact2.asp)
4
Introduction
PiXORD PD614 Series Network Camera delivers superior H.264-AVC performance, state
of the art design and function. PD614 Series is specifically adapted for maximum
performance indoor applications, such as commercial, banking, government buildings,
schools, universities and airports.
H.264-AVC video compression can lower bandwidth and storage requirements without
compromising image quality; Motion JPEG is supported for increased flexibility, as well as
multiple independent video streaming.
PD614 value-added features include; on-board video motion detection, two-way audio,
Micro SD card storage and PoE model is available with full PoE (IEEE-802.3af) feature that
supplies function of power to the camera via the network, eliminating the need for power
cables, reducing installation costs and complexity. Consequently, PD614 is “Best in Class”
for maximum performance IP video surveillance systems, demanding superior image
quality, ease of installation, and intelligent video capabilities.
5
Installation
1. Hardware
6
2. Software Installation
The following software is necessary for the proper display and use of the P600 from the Web
site. The software will be available from the Software Package CD.
IP Installer
The IP Installer is used to locate and configure network cameras and video servers on
the LAN. This utility is useful for conveniently configuring the network settings of the
device, or for finding a device once the network settings have been modified. To install
the IP Installer, from the Software Package CD UI, select IP installer, then follow the on
screen instructions.
VLC
Though not necessary, this can be used for viewing the streaming without a Web
browser.
7
3. Network Configuration
IP Installer is a utility that provides an easier, more efficient way to configure the IP
address and network settings of the devices. It even provides a convenient way to set the
network settings for multiple devices simultaneously using the batch setting function.
Moreover, IP Installer can save the network settings for all devices as a backup and
restore them when necessary. NOTE: Default mode is DHCP.
Preparation before IP Assignment
1.
Always consult your network administrator before assigning an IP address to your server
in order to avoid using a previously assigned IP address.
2.
Ensure the device is powered on and correctly connected to the network.
3.
MAC Address: Each device has a unique Ethernet address (MAC address) shown on the
label of the device as the serial number (S/N) with 12 digits (e.g. 000429-XXXXXX).
*0004290000
B1
4.
Although the IP Installer is able to find and configure any Pixord devices on the LAN
except those that are behind a router, it is a good idea to set the host PC to the same
subnet. In order to connect to the Web-based user interface of the camera, the host PC
must be in the same subnet. For more information about subnets, please consult your
network administrator.
Using IP Installer to Assign an IP Address to PD614
1.
Once IP Installer has been successfully installed on the PC, double click the IP Installer
icon on the desktop, or select it from Start > Programs > Pixord > Device Search > IP
Installer.
8
2.
Click the menu bar Tool > Search Network Device to search the device in the LAN.
3.
From the list, select the device with the MAC Address that corresponds to the device that
is to be configured. The MAC Address is identical to the unit’s S/N (Serial Number).
4.
Double click the item to open the Property Page for the selected device or click the menu
bar View > Property.
5.
After filling in the properties, click [Set] button to complete the configuration settings in
the remote device while saving configuration in the PC.
9
Open the Web-based UI of the selected camera
1.
To access the Web-based UI of the selected unit, run the View > Open Web on the menu
bar.
2.
If the device has been configured correctly, the default Web browser will open to the
home page of the selected device.
3.
If you find your browser is opened and automatically connected to the camera Home
Page, it means you’ve assigned an IP Address to the unit successfully. Now you can
close the IP Installer and start using your camera.
Verify and Complete the Installation from Your Browser
When browsing the Home Page for the first time with the Microsoft Internet Explorer
TM
, you
must temporarily lower your security settings to perform a one-time-only installation of the
ActiveX component onto your workstation, as described below:
1.
From the Tools menu, select [Internet Options]
2.
Click the [Security] tab and then click [Custom Level] button to see your current security
settings.
3.
Set the security level to Low and click [OK].
4.
Type the URL or IP address of your camera into the Address field.
5.
A dialog box will pop up asking if the ActiveX control should be installed. Click [Yes] to
start the installation.
10
Once the ActiveX installation is complete, return the security settings to their original value, as
noted above.
11
Access to the Camera
Following the successful installation and IP assignment, PD614 camera will be able to be
accessed. The intention of accessing to the camera is most likely for the live video images;
there are various configurations as well. It works with most Windows system and Browsers.
The most recommended browser is Microsoft Internet Explorer (7.0 or above). Other browsers,
like Mozilla Firefox, Apple Safari and Netscape Navigator, are functionalities/configurations
partially supported, while live video can work on those platforms where VLC must be installed
as the video codec.
Note: With Internet Explorer of the access, the installation of ActiveX control is required as
described in the previous section.
The Live View Page
The first view of logging into the camera web is the live video images with information
including camera IP address, video format / resolution / frame rate / bit rate and system date.
The Quick Function Buttons come with the video panel for immediate functions or taking
effect.
Full screen: enlarge the video image to the current screen size.
Listen: the audio sent from camera
Talk: the audio sent to camera
Record: record current live video images in “.avi” format
Snapshot: Capture a still live image in JPEG format
12
Further configurations and options; a prominent button in between is used to expand the
further operations. Not all buttons of function are described below. Options appear when
specified in the configuration page.
SETUP: Further configurations and functions
LANGUAGE: Language selection for the Web Interface.
IMAGE SETUP: An actual size check box. Default is unselected, which Image frame is scaled
down or enlarged to fit the web VGA size.
MANUAL TRIGGER: Applied as one of the trigger conditions, see Event Handling for detail.
VIDEO STREAM: Select the current displayed stream.
13
Video and Image Configuration
This section describes how to configure the video streaming from the device, and the related
camera image configurations. Users with Administrator or Operator (see Users Settings)
authority are intended for these configurations.
Click on
button to enter in the configuration pages.
Video
There are 3 tabs,
-
General
-
Advanced
-
External Video Source
14
General
Video General Setting
The list of video streams is provided for enable/disable selection. Stream1 is default enabled
(selected). Maximum 3 streams can be concurrently enabled for different client requests.
Digital PTZ: This function is available in stream2.
OSD Setting
Enable the On Screen Display (OSD) information. A line of text message (e.g. Camera Name
or Position) and the date/time string are available to be selected for displaying or hiding on the
images.
15
Advanced
The Video Advanced setting page provides more detail stream configurations. These settings
can affect video size, quality. The expected transferring performance must be under the
condition of full network bandwidth
RTSP Path The RTSP Path is the stream ID used for RTSP client streaming connection, such as VLC
player. The default values are v00, v01 and v02 for the three streams respectively. The string
can be any combination of number or capital/small letters. It can not be empty however.
Resolution The resolution here describes an image size counted by width and height, e.g. 640x480,
st
referring to pixel resolution. The 1 stream can be set from more options of resolution;
1600x1200 (2 megapixels), 1280x720(HD), 800x600(SVGA), 640x480(VGA),
320x240(QVGA). While Stream2 has the options of VGA and QVGA, stream3 is in a fixed
resolution, the QVGA.
Video Mode This option allows the selection of two bit rate modes, the Constant Bit Rate (CBR) or Variable
Bit Rate (VBR). CBR refers to the setting of a fixed Target Bit Rate (configuration in the rage
of 64Kbps to 6Mbps) that would apply in the case of limited bandwidth or/and storage
requirement. While CBR concerns a fixed data rate transmitting, the video quality is of high
priority for VBR mode selected. VBR therefore is configured with the Quality Level (Standard,
16
Good, Best). In general, CBR predicts the provided condition; if image activity requires higher
bit rates than configured, the frame rate and quality would be affected as not likely to increase
bandwidth (bit rate). In spite of the required recording storage estimation, VBR is by way of
compensation that adjustable bit rate fits the actual image activity.
Image Format H.264 and MJPEG are available for image format selection. The term, “image format”, is
referring to compression / encoding technique. The selection of image format decides the
performance of bandwidth and storage requirement. In the request of same video quality,
H.264 contributes to less bandwidth and storage requirement, which is more efficient than
MJPEG.
GOP In MPEG4/H.264 video coding, GOP (group of pictures) describes how the different types of
frames are arranged. The frame types implemented here are I-frame (full image information)
and P-frame (motion-compensated difference information). This setting configures the GOP
length which is the number of frames before next I-frame appears. Having more I-frames
usually increases the stream size, and therefore more bandwidth and storage are required.
Frame Rates The Frame Rates defines the number of frames that will be displayed per second. The frame
rate setting can affect the target bit rate (bandwidth requirement) and storage requirement.
Note:
While multiple streaming is possible, each stream has its limitation and dependency to other
stream. See “Video Stream Specification”.
17
External Video Source
This page is provided to configure and keep other video links (from specified Pixord video
models) that will be applied in the web access of the current camera unit, for instance, the
application of video conference.
To add an external video link, click “Add…” to show the configurations. The “Product Type:”
lists the models that are applicable in this function. While the proper configuration is done, click
“Connect” to test the existence of destination server and preview the images.
18
Video Conference
When “External Video Source” is configured with at least one link, the video conference button
can be found on the live view page.
Press the button, the Video Conference will then be presented as below; the local video is
showing left hand side, while right panel is displaying remote site video images.
19
Camera
This page provides the basic image color appearance and further image settings.
General
Brightness: the luminance of image view
Hue: refer to pure a pure color, or described by its name, such as red, green or blue.
Saturation: intensity of a specific color
The 3 correlates are referring image appearance in terms of color/vision. These are adjustable
from this page.
Rotation: rotate the image, so it looks up-side down. This can be applied when camera unit
must be ceiling mounted and the image is therefore reversed.
20
Audio: enable this option, so the video stream will be transferring accompanied with the audio
data.
Web Record / Snapshot: define the location where snapshot images and video clips will be
stored. The file name is referring to the prefix of the actual file name of each snapshot image or
video clip generated.
Advanced
White balance: the adjustment to compensate for different environments in terms of light
source.
Exposure: Anti-flicker setting for image sensor to fit the frequency of light (power) source. For
instance, the power frequency is 50Hz for most European countries, while 60Hz is typically for
US. This setting is therefore regionally different. Note: Default setting is 50Hz
Max. Exposure Time: referring to the shutter speed.
Max. Gain Control: the amplification factor for the incoming light.
Status LED: Turn ON/OFF the status LED.
21
Event Handling
Event Handling describes the configurations of event type and the corresponding actions. To
have an insight into this function, a common example can be storing a captured image to a
local storage or remote FTP server (Actions), when there is a Motion Event (Trigger Condition)
Event Server
The “Event Server List” lists the configured server(s) that will act as a remote storage or a
destination for handling the triggered event. Currently, FTP is the only available server type.
Up to 10 FTP servers can be added in the list.
22
Motion Detection
A snapshot image shows the whole view of the camera covered. To select a motion detection
area, click directly on the image, then change the size and position by dragging and drawing.
Up to 10 motion areas (configurations) can be added in the list. Each detection area can be set
with its own sensitivity value.
23
Event Configuration
The Event Configuration is to assign the actions responding to the specified events (Trigger
Conditions).
The table lists the configured events. Click on “Add…” or choose an event from the list to
expend the panel for detail configurations. “Remove” is to delete a selected event.
24
Trigger types (conditions)
Motion Detection: The configured detection area(s) for motion events.
Manual Trigger: a virtual trigger button embedded on the web main page.
When triggered” Actions
Store image to FTP (Remote) / Micro SD Storage (Local)
Send Email Notification
Event Schedule
Events may come frequently, for instance, a moving object keeps triggering as being in a
detection area. False alarms can therefore occur. The “minimum time between triggers”
setting is then for this case. System waits for the given time before the next trigger taken.
By default, each configured event is always effective. It can also be scheduled by selecting
start day/time and the duration of effective.
25
Local Storage and Schedule Recording
PD614 is equipped with a card slot for storage. This storage is applied for local video recording.
The recording function can be launched according to schedule. The micro-SD card also
records the JPEG images responding to an event.
General
Define the day (specified by days of a week) and time (specified by each single hour) for that
will be recording during the scheduled period. User can select which video stream should be
recorded, and the size of each sliced file. When the check box is ticked, recording process
starts at the scheduled hours (red blocks).
Storage
Display the storage information, includes disk size info, type and status. The warning message
(red text) shows when recording is on process; Micro-SD card should not be removed during
the recording process.
26
The “Browse” button allows viewing the list of recorded files. The web page will then be
redirect to the root path of the SD storage (if one is inserted). The list includes couple of folders,
the Oevent_images which contains all the still images captured by any event trigger, and
folders specified by date where the recorded video files are located.
The recorded files are named in date_time format, and the extension file name is “.h264”.
While file is in h264 raw format, it can be played in VLC player. Note that the recorded file
includes video only; no audio information is recorded.
27
Network Configuration
IP Camera acts as one of the network devices. It is therefore allowed “IP” to be assigned, so
certain network functionalities can be implementable within this device. This section describes
these configurations. Fundamentally, for instance, the IP assignment of the device can be
done via DHCP server, manually fixed IP option or PPPoE to obtain IP from service
provider.
General
Device IP configuration, includes DHCP, Static IP setting and PPPoE. “Enable ARP/Ping”
enable device to accept ARP or ping packets from the network. Disable this option may
provide extra security from intentional ping.
28
Advanced
Enable or configure other network functions.
NTP: Configure a NTP (Network Time Protocol) server, so that the device system date and
time can be synchronized with a specified Time Server. This configuration is provided for one
of the potions of system date/time adjustment.
HTTP: set the HTTP port that will be applied for Web UI access.
RTSP: set the RTSP (Video) port for video data transmission.
HTTPS: Enable/Disable Http security function.
Bonjour: Enable Bonjour service, so that the device can be discovered with “Bonjour” service
applied.
UPnP: Enable UPnP, so that the device can be discovered in an UPnP Compliant Network.
NAT Traversal: Enable NAT traversal, so that client from Internet can have access to the
devices behind the Router.
Note: with UPnP enabled, the IP Sharing device (Router) capable of UPnP function will
automatically be noticed with the device’s NAT port.
29
SMTP(E-Mail)
Configure an email host in the device that will send email on behalf of the configured email
account in a circumstance like sending an email notice to a specified mail address (Event
Configuration).
Sender: Complete the Mail Server, Server Port, Authentication information (if required) and
the sender’s email address.
Receiver: The receiver email address
DDNS
Dynamic DNS configuration; the network device can be assigned and accessed with a host
name instead of IP address by registering this service (Internet access required).
Host Name: Assigned name that will be used for access to the device
User Name/Password: Account authentication for logging to this service
Update Time: Periodically, the device updates its access info to sever in the configured time.
Response: the device responds the connection info.
30
System Options
Information
Lists of System and Network configurations
User
Login users for Web access and operations; authentication required. The Check box is for
anonymous logging on to the live view page. Logging for further configurations will still require
user name and password.
31
Date & Time
System date/time configuration. Options of synchronizing with PC and NTP server are
provided for automatic adjustment.
32
Server Maintenance
This page provides tools for system maintenance; Reboot and Load default settings, as well as
functionalities of launching upgrade process, backup/restore user settings and language
defines.
Log Service
Most system operations and / or process will be kept in a log system. The link provides the
review of these records.
33
Web Interface Customization
This page provides the function of adjusting the look of live view page. There are two types of
layout settings; use default look or use custom settings.
Use Default Look: the default layout of live/configuration pages
Use Defined Links: Web link(s) will be presented on the live page when enabled. It can be a
link to another IP camera for instance, or other preferred web link.
34
Use Custom Settings: The modifications allowed are change of Background / Text Color,
Background picture, Title, Description, Logo and etc.
35
Troubleshooting
Check firmware version
The version code can be found in Setup -> System -> Information, or simply type
“version.html” after the URL address, e.g. http://192.168.0.200/version.html. Firmware version
indicates the functionalities’ updates or availability in the camera system. Therefore, in the first
step of troubleshooting and then reporting, it helps to locate the found issues. Newer version
firmware may have corrected the current bugs.
36
Upgrade device firmware
Firmware upgrade process should be done via the web configuration; Setup -> Server
Maintenance -> Firmware Upgrade. Before the process, read the instructions and release
notes coming with each new released version. For the steps,
1.
Check and retrieve the latest firmware bin file.
2.
Disconnect all clients (e.g. streaming requests) to the device that will be firmware
upgrading.
3.
Stop the local (schedule) recording if it was enabled.
4.
Go to the Firmware Upgrade page, browse and locate the downloaded firmware bin file,
then click on “Upgrade” button.
5.
The upgrade should start in minutes, depending on file transferring status. The web will
then be directed to the system writing progress. Overall upgrading process takes about
5~10 minutes. In this period, DO NOT DISCONECT the power. System of the unit can be
damaged otherwise.
6.
The power LED (orange one) will be quick/slow flashing during the upgrading process.
When it becomes again steady on, camera is ready to be accessed. Check the firmware
version. If somehow system is not upgraded, redo above steps. In the case, restore
factory default process may be required.
37
Restore Factory Default Settings
In some cases, system does not respond to any operation, this process gets the unit back to
initial status, so that it can be reconfigurable for up and running again.
To restore factory default, follow the steps below:
1.
Unplug the power jack to turn off the camera
2.
Press the button (circle in red) and keep it pressed until instructed to release.
3.
Plug in the power jack to turn on the camera. The LED will start flashing in a short
while.
4.
Release the button when the LED starts quick flashing. The device should be set
back to factory default.
38
Video Streams Specification
The availabilities
1.
Each stream can be switched to either H.264 or MJPEG mode.
2.
Each steam can be configured to either CBR or VBR mode.
3.
Stream1 (main stream) is available from all the resolutions listed.
4.
The maximum resolution setting for Stream2 is 640x480.
5.
Stream3 is fixed in 320x240.
6.
The maximum frame rate for transferring 1600x1200 is 15fps. Others can reach up to
30fps.
STREAM1
STREAM2
STREAM3
V
V
V
V
V
V
Encoding Mode
H.264 / MJPEG
Transferring Mode
CBR / VBR
Resolution @ Max. FPS
1600x1200@15
V
1280x720@30
V
800x600@30
V
640x480@30
V
V
320x240@30
V
V
V
Dependency
1.
Max. FPS dependency: when Stream1 is set to 1600x1200, the maximum frame rate is
15fps. Accordingly, both Stream2 and Steram3 can be configured with the frame rate
from 5 to 15 fps.
2.
Resolution dependency: The maximum resolution of Stream2 is depending on the
resolution setting of Stream1. When Stream1 is set to 320x240, Stream 2 is limited in
320x240.
3.
Frame rate independent: Frame rate setting for each stream can be independent, for
instance, Stream2 can be set 15fps and Stream3 is 30fps while Stream1 (1280x720 or
below) is set to 5fps.
39
STREAM1
1600x1200, 5~15 fps
STREAM2
640x480
320x240
STREAM3
320x240 (fixed)
5~15 fps
5~15 fps
1280x720, 5~30 fps
800x600, 5~30 fps
5~30 fps
5~30 fps
640x480, 5~30 fps
320x240, 5~30 fps
5~30 fps
Note the resolution setting must follow the sequence: Stream1 ≧ Stream2 ≧ Stream3.
40
">
