Allen-Bradley ArmorBlock 2-port EtherNet/IP Modules Installation Instructions

Installation Instructions
Original Instructions
ArmorBlock 2-port EtherNet/IP Modules
Catalog Numbers 1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR, 1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R,
1732E-16CFGM12P5QCWR
Topic
Summary of Changes
Before You Begin
Install the Module
Set the Network Address
Mount the Module
Connect the I/O, Network, and Auxiliary Cables to the Module
Configure the Module
Interpret Status Indicators
Specifications
Additional Resources
Page
1
3
5
5
5
6
9
10
12
14
Summary of Changes
This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.
Topic
Added inclusive language acknowledgment
Updated Certifications
Page
2
14
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or
maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable
code of practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
岤䠑㖈㸝鄳ծꂁ縨ծ乼⡲ㄤ絶䫡劥❡ㅷ⵸霼ꢓ靀劥俒咓⟄⿺  Ⱖ➭餴彂  鿈ⴔ⴩ⴀ涸剣Ⱒ霃㢊㸝鄳ծꂁ縨ㄤ乼⡲涸湱䎾俒咓կꤑ✫䨾剣鷓欽錞薴ծ岁䖒ㄤ叻ⲥ涸
湱Ⱒ銳宠⛓㢪欽䨪鵮䗳곢擿䜪㸝鄳ㄤ䱹絁霹僈կ
㸝鄳ծ靈侮ծ䫏鵘ծ⢪欽ծ絆鄳ծ䬒⽸ㄤ絶䫡瘝ぐ고乼⡲䗳곢歋絑鵂鷓䔲雲絅涸⚁⚌➃プ䭽撑鷓欽涸乼⡲錞薴㹊倶կ
㥵卓劢䭽撑ⵖ鸣㉁䭷㹁涸倰䒭⢪欽霪霃㢊ⴭ〳腊⠔䰀㹲霃㢊䲿⣘涸⥂䫡կ
ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos adicionales acerca
de la instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos los códigos, leyes y estándares
vigentes.
El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el
código de práctica aplicable. Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.
ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou manter este
produto. Os usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.
É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e especializado, de
acordo com o código de prática aplicável.
Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.
ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и документы,
перечисленные в разделе «Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации данного оборудования.
Пользователи обязаны ознакомиться с инструкциями по установке и прокладке соединений, а также с требованиями всех применимых норм, законов и
стандартов.
Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться
обученным персоналом в соответствии с применимыми нормами и правилами.
Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.
:
ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten,
bevor Sie dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zusätzlich mit den
Installations- und Verdrahtungsanweisungen vertraut machen.
Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in Übereinstimmung mit
den anwendbaren Ausführungsvorschriften vorgenommen werden.
Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.
ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant d’installer,
configurer, utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois et normes en vigueur.
Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de pratique en
vigueur.
Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.
:
,
,
,
.
,
.
,
,
,
,
,
,
.
.
ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione “Altre
risorse”, riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti
dalle leggi, codici e standard applicabili.
Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.
Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.
DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer listelenmiş
dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.
Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçaları sökme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama yönetmeliklerine uygun
şekilde yapılabilir.
Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.
岤䠑✲갪㖈㸞酤鏤㹁乽⡲䧴笞隌劥欴ㅷ⵹锞⯓ꠗ隡姽俒⟝⟃⿻⴪倴 չⰦ➮须彂պ畎眏⚥剤ꡠ㸞酤鏤㹁莅乽⡲姽鏤⪔涸俒⟝⢪欽罏䗳갭擿䜫㸞酤ㄤꂂ箁䭸
爚⚛痘ざ䨾剤岁鋊岁䖒ㄤ垦彋銴宠
⺫䭍㸞酤锅侮❜➰⢪欽⢪欽穉酤䬓⽹ㄤ笞隌瘞⹛⡲鿪䗳갭❜歋䊺竤麕黠殹鎯箻涸➃㆞鹎遤⟃痘ざ黠欽涸㻜⡲岁鋊
㥶卓㼟鏤⪔欽倴ꬌ醢鸤㉂䭸㹁涸欽鸁儘〳腋剚鸤䧭鏤⪔䨾䲿⣘涸⥃隌⸆腋「䴦
POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně instalace,
konfigurace a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů a norem nutně seznámit také s pokyny pro instalaci a elektrické zapojení.
Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.
Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.
UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe źródła
omawiające instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania, jak również z
obowiązującymi kodeksami, prawem i normami.
Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel zgodnie z
obowiązującym kodeksem postępowania.
Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.
OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller börjar använda
eller utföra underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och standarder.
Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.
Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.
LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product
installeert, configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en
normen.
Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en
in overeenstemming met de geldende praktijkregels.
Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.
Rockwell Automation recognizes that some of the terms that are currently used in our industry and in this publication are not in alignment with the movement toward
inclusive language in technology. We are proactively collaborating with industry peers to find alternatives to such terms and making changes to our products and content.
Please excuse the use of such terms in our content while we implement these changes.
2
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Environment and Enclosure
ATTENTION: This equipment is intended for use in overvoltage Category II applications (as defined in EN/IEC 60664-1), at altitudes up to 2000 m
(6562 ft) without derating.
This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such
environments.
This equipment is supplied as Type 1 enclosed equipment (only when provided with dust cap on the Input and Output connectors or terminated with
cables). It should not require additional system enclosure when used in locations consistent with the equipment Enclosure Type Ratings. Subsequent
sections of this publication may contain more information regarding specific enclosure type ratings, beyond what this product provides, that are
required to comply with certain product safety certifications.
In addition to this publication, see the following:
• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for additional installation requirements.
• NEMA Standard 250 and EN/IEC 60529, as applicable, for explanations of the degrees of protection provided by enclosures.
ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration, and operation of this
equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring
instructions in addition to requirements of all applicable codes, laws, and standards.
Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained
personnel in accordance with applicable code of practice. In case of malfunction or damage, no attempts at repair should be made. The module
should be returned to the manufacturer for repair. Do not dismantle the module.
Prevent Electrostatic Discharge
ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these
guidelines when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.
ATTENTION:
• Make sure that all connectors and caps are securely tightened to properly seal the connections against leaks and maintain Type 1 and IP enclosure
type requirements.
• Read this document and the documents listed in the Additional Resources section about installation, configuration, and operation of this equipment
before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions
in addition to requirements of all applicable codes, laws, and standards.
• Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained
personnel in accordance with applicable code of practice. In case of malfunction or damage, no attempts at repair should be made. The module
should be returned to the manufacturer for repair. Do not dismantle the module.
• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.
Electrical Safety Considerations
ATTENTION: This device is intended only for installation on Industrial Machines in accordance with NFPA79. Due to the nature of these devices (fixed
equipment using cable connections) they are not suitable for installation in accordance with the NEC (NFPA70).
Before You Begin
The ArmorBlock® I/O modules communicate via EtherNet/IP™. The sealed IP65, IP66, IP67, and IP69K housing of these modules requires no enclosure. The I/O modules have
dual Ethernet ports and use an embedded Ethernet switch.
See Figure 1 to familiarize yourself with major parts of the module.
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
3
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Figure 1 - Module Identification
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR,
1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
1732E-16CFGM12P5QCWR
1
2
1
1
LINK 1
PORT 1
LINK 1
LINK 2
MOD
NET
PORT 2
3
LINK 2
5
3
4
5
5
8
4
8
7
7
6
AUX POWER
Component Description
1
Description
EtherNet/IP D-coded M12 connector
5
Description
M12 style I/O connectors
2
Functional Earth(1)
6
Mini-style auxiliary power out
3
Status indicators
7
4
Node address switches
8
Protective Earth(2)
Mini-style auxiliary power in
(1) Functional earth grounds the I/O block EtherNet/IP communication circuitry, which is designed to mitigate the effect of noise on the network. See EtherNet/IP Connector on page 8.
(2) Protective earth is provided for the grounding of field devices and is internally connected to each Pin 5 of the M12 I/O connectors. See I/O Connectors on page 7.
Catalog Number Explanation
Catalog Number
1732E-IB16M12R
1732E-OB16M12R
1732E-IB16M12DR
1732E-OB16M12DR
1732E-16CFGM12R
1732E-IB16M12SOEDR
1732E-16CFGM12P5QCWR
4
Description
Network Connector
16 channel 24V DC digital input dual-port Ethernet/IP module
16 channel 24V DC digital output dual-port Ethernet/IP module
Dual D-coded M12
16 channel 24V DC digital input dual-port Ethernet/IP module with sensor source
diagnostics
16 channel 24V DC digital output dual-port Ethernet/IP module with individually fused
outputs and diagnostics
16 channel 24V DC self-configurable I/O dual-port Ethernet/IP module with individually
fused outputs
Dual D-coded M12
16 channel 24V DC digital I/O dual-port Ethernet/IP with sensor source diagnostics and
Sequence of Events support
16 channel 24V DC self-configurable digital I/O dual-port Ethernet/IP metal WeldBlock
module with QuickConnect
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
Auxiliary Power
Single 4-pin mini
Single 4-pin mini
Dual 5-pin mini
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Install the Module
To install the module:
1.
2.
3.
Set the Network Address
Mount the Module
Connect the I/O, Network, and Auxiliary Cables to the Module
Set the Network Address
The I/O block ships with the rotary switches set to 999 and Dynamic Host Configuration Protocol (DHCP) enabled.
To change the network address, you can do one of the following:
•
•
•
Adjust the switch on the front of the module.
Use a DHCP server, such as Rockwell Automation® BootP/DHCP.
Retrieve the IP address from nonvolatile memory.
The I/O block reads the switches first to determine if the switches are set to a valid number. To set the network address:
1.
2.
3.
4.
Rotate the three switches on the front of the module using a small blade screwdriver.
Align the small notch on the switch with the number setting you wish to use.
Valid settings range from 001…254.
Cycle power.
Set Network Address
Example shows the default
node address set at 163.
When the switches are set to a valid number, the I/O block IP address is 192.168.1.xxx (where xxx represents the number set on the switches). The I/O block subnet mask is
255.255.255.0 and the gateway address is set to 0.0.0.0. When the I/O block uses the network address set on the switches, the I/O block does not have a host name assigned
to it or use any Domain Name Server.
If the switches are set to an invalid number (for example, 000 or a value greater than 254 excluding 888), the I/O block checks to see if DHCP is enabled. If DHCP is enabled,
the I/O block asks for an address from a DHCP server. The DHCP server also assigns other Transport Control Protocol (TCP) parameters.
If DHCP is not enabled, the I/O block uses the IP address (along with other TCP configurable parameters) stored in nonvolatile memory.
Mount the Module
Two sets of mounting holes are used to mount the module directly to a panel or machine. Mounting holes accommodate #8 (M4) pan head screws. The torque specification
is 1.13 N•m (10 lb•in).
Product Dimensions
See Figure 2 for the mounting dimensions illustration to help you mount the module.
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
5
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Figure 2 - Module Dimensions
1732E-16CFGM12P5QCWR
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR,
1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
65 mm
(2.56 in.)
60.4 mm
(2.38 in.)
43.25 mm
(1.70 in.)
26.5 mm
(1.04 in.)
28 mm
(1.1 in.)
PORT 1
LINK 1
45 mm
(1.77 in.)
LINK 1
LINK 2
MOD
NET
PORT 2
LINK 2
200 mm
(7.87 in.)
179 mm
(7.05 in.)
189.6 mm
(7.46 in.)
169 mm
(6.65 in.)
AUX POWER
Front view
Side view
Front view
Side view
Mount the Module in High Vibration Areas
If you mount the module in an area that is subject to shock or vibration, we recommend you use a flat and a lock washer to mount the module. Mount the flat and the lock
washer as shown in the mounting illustration. Torque the mounting screws to 1.13 N•m (10 lb•in).
Figure 3 - High Vibration Area Mounting
Lock washer
Flat washer
Connect the I/O, Network, and Auxiliary Cables to the Module
The ArmorBlock EtherNet/IP family has 5-pin micro-style connectors. We provide caps to cover the unused connectors on your module. Connect the quick-disconnect cord
sets you selected for your module to the appropriate ports.
6
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
I/O Connectors
See the pinout diagrams for the I/O connectors.
Figure 4 - Micro-style 5-pin input Female Connector
1
2
5
4
3
View into Connector
Pin
1
2
3
4
5
Function
Sensor source voltage
Input B
Return
Input A
Protective Earth
Figure 5 - Micro-style 5-pin Output Female Connector
1
2
5
4
3
View into Connector
Pin
1
2
3
4
5
Function
Not used
Output B
Return
Output A
Protective Earth
Self-configuring Modules
The 1732E-16CFGM12R and 1732E-16CFGM12P5QCWR self-configuring modules contain both input and output functionality.
•
•
•
If an I/O point is to be an output, dedicate that point as an output with a wired load and energize it through a control program.
Energized outputs show an associated active input that can be used as a feedback mechanism to verify that the output is On.
If an I/O point is to be an input, wire the input device as normal and leave the associated output de-energized at all times.
Figure 6 - Micro-style 5-pin Selectable Point Connector
1
2
5
4
3
View into Connector
Pin
1
2
3
4
5
Function
Sensor source voltage
Input or Output B
Return
Input or Output A
Protective Earth
ATTENTION: Make sure that all connectors and caps are securely tightened to properly seal the connections against leaks and maintain Type 1 and IP
enclosure and requirements.
I/O Self-configure Circuitry
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
7
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
EtherNet/IP Connector
Figure 7 - D-coded Micro Network Female Connector
Pin
Function
1
M12_Tx+
2
M12_Rx+
3
M12_Tx-
3
4
M12_Rx-
View into Connector 1
5
Connector shell shield ground
Pin
Function
1
M12_Rx+
2
M12_Tx+
5
1
4
2
3
2
4
3
M12_Rx-
5
4
M12_Tx-
View into Connector 2
5
Connector shell shield ground
1
IMPORTANT
Use one of the following mating connectors for the D-coded M12 female network connector:
• Polyamide small body unshielded (1585D–M4DC–H)
• Zinc die-cast large body shielded (1585D–M4DC–SH)
Enable QuickConnect
To enable QuickConnect for the Ethernet ports, use the RSLogix 5000® or Studio 5000 Logix Designer® application Module QuickConnect tab and check the Enable
QuickConnect option. For more information on the QuickConnect system setup, see EtherNet/IP QuickConnect Application Technique, publication ENET-AT001.
After the QuickConnect feature is set to ON, the module must be power cycled. QuickConnect is active during the next connection.
Once active, the QuickConnect feature automatically sets all Ethernet ports to:
•
•
•
•
Speed = 100 Mbps
Duplex = Full
Auto-negotiate = Off
Automatic Cross-over Cable Detection (auto-MDIX) = Off
If you configure BootP/DHCP, QuickConnect changes the configuration to retain the current IP address. Disabling the QuickConnect feature automatically sets all Ethernet
ports to Automatic Cross-over Cable Detection (auto-MDIX) = On.
To reset the Ethernet ports to Auto-negotiate or the IP address to DHCP request, do one of the following:
•
•
•
Change the setting on the module webpage
Change the setting in the RSLogix 5000 or Studio 5000 Logix Designer application
Perform a factory reset
Auxiliary Power Connector
The 1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR, 1732E-OB16M12R, 1732E-OB16M12DR, and 1732E-16CFGM12R modules use 4-pin auxiliary power connections. Attach
the mini-style 4-pin connector to the mini-style 4-pin receptacle as shown in Figure 8.
Figure 8 - Mini-style 4-pin Receptacle
Male Input
4
3
Female Output
2
1
View into Connector 1
8
Pin
Function
1
Output power+
2
Sensor/MDL power+
3
Sensor/MDL power-
4
Output power-
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
2
4
1
3
View into Connector 1
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
The 1732E-16CFGM12P5QCWR module use 5-pin auxiliary power connections. Attach the mini-style 5-pin connector to the mini-style 5-pin receptacle as shown in Figure 9.
Figure 9 - Mini-style 5-pin Receptacle
Male Input
5
1
Female Output
Pin
Function
1
Output power-
2
Sensor/MDL power-
5
4
3
Protective Earth
3
4
Sensor/MDL power+
View into Connector 1
5
Output power+
2
4
1
2
3
View into Connector 1
The grounds for both module power and output power are shared.
ATTENTION: This equipment is considered Group 1, Class A industrial equipment according to IEC/CISPR 11. Without appropriate precautions, there
may be difficulties with electromagnetic compatibility in residential and other environments due to conducted and radiated disturbance.
Auxiliary power is based on a 4-pin and 5-pin connector system and is used to provide 24V DC power to I/O modules and other devices. Running separate power to these
devices is most typically used for I/O devices with output connections to prevent power supply interruption due to switching of outputs. However, some devices require
separate auxiliary power to power them regardless of the presence of outputs.
Depending on the devices used, it may be possible to provide power through only one pair of the four available pins, and in this case the other available pair may be used for
single channel E-stop by using special E-stop drop or power T-ports and shorting plugs. Allen-Bradley® E-stop T-ports and shorting plugs are red for easy identification.
Configure the Module
See Figure 10 for configuration operations.
Figure 10 - Configure Operations
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR,
1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
EtherNet/IP D-coded
M12 connector
LINK 1
1732E-16CFGM12P5QCWR
EtherNet/IP D-coded
M12 connector
LINK 2
PORT 1
LINK 1
LINK 2
MOD
NET
PORT 2
EtherNet/IP D-coded
M12 connector
Node address
switches
M12 style
I/O connectors
Mini-style
auxiliary
power in
M12 style I/O connectors
Node address
switches
Mini-style
auxiliary
power in
M12 style
I/O connectors
Mini-style
auxiliary power out
AUX POWER
See Essential Components Selection Guide, publication EC-CA100, for Rockwell Automation cable and cord set offerings or use the Product Selection and Configuration tools
available at rok.auto/systemtools.
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
9
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
External Repository for Random Data (ERRD)
The QuickConnect modules provide onboard nonvolatile memory, of up to 6K bytes, for storing block-specific data such as Tool ID and counter value. You can read from and
write to the module memory.
To read from the module
1.
Send an EtherNet/IP Explicit Message with the following information:
Service Code
Class ID
Instance ID
Attribute ID
Request Data
4C (hex)
6E (hex)
1
1
Data Payload (total 8 bytes):
Offset Description
0x00 Address to Read from
0x04 Number of bytes to read (max 472 bytes)
To write to the module
2.
Send the following three EtherNet/IP Explicit Messages:
Start Command
Service Code
Class ID
Instance ID
Attribute ID
06 (hex)
6E (hex)
1
1
Write Command
Service Code 4D (hex)
Class ID
6E (hex)
Instance ID
1
Attribute ID
1
Data Payload (max 8+ 472 bytes):
Offset Description
Request Data 0x00 Address to Write to
0x04 Number of bytes to write (max 472 bytes)
0x08 User Data (Array of USINT)
Stop Command
Service Code
Class ID
Instance ID
Attribute ID
07 (hex)
6E (hex)
1
1
Interpret Status Indicators
This module has the following indicators:
•
•
•
10
Network, Module, and Link status indicators for EtherNet/IP
Auxiliary Power indicator
Individual I/O status indicators for inputs and outputs
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Figure 11 - Status Indicators
1732E-16CFGM12P5QCWR
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR,
1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
Network link
status
LINK 1
LINK 2
Network
status
indicator
Module status
indicator
Network link
status
Module
status
indicator
PORT 1
LINK 1
LINK 2
MOD
NET
PORT 2
Network
status
indicator
Input
status
indicators
I/O status
indicators
I/O status
indicators
Output
status
indicators
Power
status
indicator
AUX POWER
Indicator Status for Modules
Indicator
Module status
Status
Off
Flashing red/green
Green
Flashing red
Red
Off
Flashing green
Network status
Network link status
Power status
Digital output status(1)
Digital input status
Green
Flashing red
Red
Flashing red/green
Off
Green
Flashing green
Yellow
Flashing yellow
Off
Green
Off
Yellow
Red
Flashing red
Off
Yellow
Red
Flashing red
Description
No power is applied to the device.
The device is in self-test.
The device is operating normally.
Recoverable fault
An unrecoverable fault – May require device replacement.
The device is not initialized or the module does not have an IP address.
The device has no CIP™ connections.
The device has an IP address, but no CIP connections are established.
The device is online, has an IP address, and CIP connections are established.
One or more connections have timed out.
The module has detected that its IP address is already in use.
The module is performing a power-up self-test.
No link is established.
Link is established on the indicated port at 100 Mbps.
Link activity is present on the indicated port at 100 Mbps.
Link is established on the indicated port at 10 Mbps.
Link activity is present on the indicated port at 10 Mbps.
No power to the device or input not valid
The power is applied to the device.
The output is not energized.
The output is energized and the output power is applied.
The output is shorted.
The output is open load condition.
No valid input
Valid input
The sensor source voltage is shorted.
The sensor source has an open wire condition.
(1) Only the 1732E-IB16M12SOEDR diagnostic module has red I/O status indicators.
IMPORTANT
In non-QuickConnect mode, the module status indicator flashes red and green for a max of 5 s while the module completes a POST (power on
self test).
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
11
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Specifications
Input Specifications — 1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR, 1732E-16CFGM12R, 1732E-16CFGM12P5QCWR
Attribute
Number of inputs
Input type
Voltage, off-state input, max
Voltage, on-state input, min
Voltage, on-state input, nom
Voltage, on-state input, max
Current, off-state input, max
Current, on-state input, max
Voltage, sensor source, min
Voltage, sensor source, max
Input delay time
On to Off
Off to On
Isolation voltage
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR, 1732E-16CFGM12R 1732E-16CFGM12P5QCWR
16
Sink, 24V DC
5V DC
12V DC
24V DC
30V DC
1.5 mA @ 5V DC
5 mA @ 30V DC
10V DC
30V DC
0…16000 µs
0, 1, 2, 4, 8, 16 ms
50V (continuous), basic insulation type, inputs, and sensor power to the
network.
No isolation between individual Inputs or between network channels.
Type tested at 707V DC for 60 s.
No isolation
Output Specifications — 1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R, 1732E-16CFGM12P5QCWR
Attribute
1732E-OB16M12R
1732E-OB16M12DR
1732E-16CFGM12R
Number of outputs
16
Output type
Source, 24V DC
Voltage drop, on-state output, max 0.5V DC
Voltage off-peak blocking, min
30V DC
Voltage, on-state output, min
12V DC
Voltage, on-state output, nom
24V DC
Voltage, on-state input, max
30V DC
Current, on-state output, max
2.0 A
0.5 A
Current per module, max
8.0 A
Leakage current, off-state output, 50 µA
500 µA
50 µA
max
4.8 A for 10 ms, repeatable
Surge current per output, min
1.2 A for 10 ms, repeatable every 2 s
every 2 s
Pilot duty rating
DC-14
50V (continuous), basic insulation type, outputs, and output power to the network.
No isolation between individual outputs or between outputs and output power
Isolation voltage
or between network channels.
Type tested at 707V DC for 60 s
1732E-16CFGM12P5QCWR
—
No isolation
General Specifications
Attribute
1732E-IB16M12DR,
1732E-OB16M12R, 1732E-OB16M12DR 1732E-IB16M12R,
1732E-IB16M12SOEDR, 1732E-16CFGM12R 1732E-16CFGM12P5QCWR
30V DC
12V DC
Voltage, auxiliary power, max
Voltage, auxiliary power, min
Current, Ethernet system power, max
0.4 A
(pins 2, 3 sensor source/module power)
Current, auxiliary power, max per output
module
(pins 2, 3 sensor source/module power plus 8 A
pins 1, 4 for output loads)
Current, auxiliary power connector, max
10 A
per module
Current, sensor source, per input, max
50 mA
Current, sensor source, per connector, max 100 mA
12
1.2 A
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
1.0 A
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
General Specifications (Continued)
Attribute
Communication rate
Status indicators
Dimensions (HxWxD), approx.
Weight, approx.
Enclosure type rating
Wiring category(1) (2)
Onboard memory type
Onboard memory, capacity, max
1732E-IB16M12DR,
1732E-OB16M12R, 1732E-OB16M12DR 1732E-IB16M12R,
1732E-IB16M12SOEDR, 1732E-16CFGM12R 1732E-16CFGM12P5QCWR
EtherNet/IP
10/100 Mbps
Full or half-duplex
100 m (328 ft) per segment
Module status - Red/green
Network status - Red/green
Link status - Green/yellow
Auxiliary power - Green
I/O channels - Yellow
I/O channels - Yellow/red – 1732E-IB16M12SOEDR only
179 x 65 x 43.25 mm (7.05 x 2.56 x 1.70 in.)
200 x 60.4 x 45 mm (7.87 x 2.38 x 1.77 in.)
340 kg (11.99 oz.)
510 g (17.99 oz.)
Meets IP65/67/69K (when marked), and Type 1 with receptacle dust caps or cable termination.
1 – On signal ports
1 – On power ports
1 – On communications port
Ferroelectric Nonvolatile RAM (FRAM)
6K bytes
(1) Use this conductor category information for planning conductor routing as described in Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1.
(2) Use this Conductor Category information for planning conductor routing as described in the appropriate System Level Installation Manual.
Environmental Specifications
Attribute
Temperature, operating
Temperature, ambient, max
Temperature, nonoperating
Relative humidity
Vibration
Shock, operating
Shock, nonoperating
Emissions
ESD immunity
Radiated RF immunity
EFT/B immunity
Surge transient immunity
Conducted RF immunity
1732E-IB16M12R, 1732E-IB16M12DR, 1732E-IB16M12SOEDR,
1732E-16CFGM12P5QCWR
1732E-OB16M12R, 1732E-OB16M12DR, 1732E-16CFGM12R
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20 °C < Ta < +60 °C (-4 °F < Ta < +140 °F)
60 °C (140 °F)
IEC 60068-2-1 (Test Ab, Unpackaged Nonoperating Cold),
IEC 60068-2-2 (Test Bb, Unpackaged Nonoperating Dry Heat),
IEC 60068-2-14 (Test Na, Unpackaged Nonoperating Thermal Shock):
-40…+85 °C (-40…+185 °F)
IEC 60068-2-30 (Test Db, Unpackaged Damp Heat):
5…95% noncondensing
IEC60068-2-6 (Test Fc, Operating):
5 g @ 10…500 Hz
EC 60068-2-27 (Test Ea, Unpackaged Shock):
30 g
EC 60068-2-27 (Test Ea, Unpackaged Shock):
50 g
IEC 61000-6-4
IEC6100-4-2:
6 kV contact discharges
8 kV air discharges
IEC 61000-4-3:
10V/m with 1 kHz sine-wave 80% AM from 80…2000 MHz
3V/m with 1 kHz sine-wave 80% AM from 2000…2700 MHz
IEC 61000-4-4:
±4 kV @ 5 kHz on power ports
±4 kV @ 5 kHz on power ports
±3 kV @ 5 kHz on signal ports
±2 kV @ 5 kHz on signal ports
±3 kV @ 5 kHz on communications ports
±2 kV @ 5 kHz on communications ports
IEC 61000-4-5:
±1 kV line-line(DM) and ±2 kV line-earth(CM) on power ports
±1 kV line-line(DM) and ±2 kV line-earth(CM) on signal ports
±2 kV line-earth(CM) on communications ports
±2 kV line-earth(CM) on shielded ports
IEC61000-4-6:
10V rms with 1 kHz sine-wave 80%AM from 150 kHz…80 MHz
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
13
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Certifications
Certification (when product is marked)(1)
c-UL-us
CE
RCM
KC
Morocco
UKCA
EtherNet/IP
Value
UL Listed Industrial Control Equipment, certified for US and Canada. See UL File E322657.
European Union 2014/30/EU EMC Directive, compliant with:
EN 61326-1; Meas./Control/Lab., Industrial Requirements
EN 61000-6-2; Industrial Immunity
EN 61131-2; Programmable Controllers
EN 61000-6-4; Industrial Emissions
European Union 2011/65/EU RoHS, compliant with:
EN IEC 63000; Technical documentation
Australian Radiocommunications Act, compliant with:
AS/NZS CISPR11; Industrial Emissions.
Korean Registration of Broadcasting and Communications Equipment, compliant with:
Article58-2 of Radio Waves Act, Clause 3
Arrêté ministériel n° 6404-15 du 29 ramadan 1436
2016 No. 1091 – Electromagnetic Compatibility Regulations
2012 No. 3032 – Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations
ODVA conformance tested to EtherNet/IP specifications.
(1) See the Product Certification link at rok.auto/certifications for Declaration of Conformity, Certificates, and other certification details.
Additional Resources
For more information on the products that are described in this publication, use these resources. You can view or download publications at rok.auto/literature.
Resource
1732E EtherNet/IP ArmorBlock Supporting Sequence of Events,
publication 1732E-UM002
EtherNet/IP QuickConnect Application Technique, publication ENET-AT001
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
Product Certifications website: rok.auto/certifications
14
Description
Detailed description of how to use and configure your 1732E-IB16M12SOEDR module.
Detailed explanation on how to set up and use QuickConnect ArmorBlock modules.
Provides general guidelines for installing a Rockwell Automation industrial system.
Provides declarations of conformity, certificates, and other certification details.
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
ArmorBlock 2-port EtherNet/IP Modules Installation Instructions
Notes:
Rockwell Automation Publication 1732E-IN009D-EN-P - June 2024
15
Rockwell Automation Support
Use these resources to access support information.
Technical Support Center
Find help with how-to videos, FAQs, chat, user forums, Knowledgebase, and product notification updates.
Local Technical Support Phone Numbers
Locate the telephone number for your country.
rok.auto/support
rok.auto/phonesupport
Technical Documentation Center
Quickly access and download technical specifications, installation instructions, and user manuals.
rok.auto/techdocs
Literature Library
Find installation instructions, manuals, brochures, and technical data publications.
rok.auto/literature
Product Compatibility and Download Center (PCDC)
Download firmware, associated files (such as AOP, EDS, and DTM), and access product release notes.
rok.auto/pcdc
Documentation Feedback
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
Waste Electrical and Electronic Equipment (WEEE)
At the end of life, this equipment should be collected separately from any unsorted municipal waste.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur
Allen-Bradley, ArmorBlock, expanding human possibility, Rockwell Automation, RSLogix 5000, Studio 5000 Logix Designer, and TechConnect are
trademarks of Rockwell Automation, Inc.
CIP and EtherNet/IP are trademarks of ODVA, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 1732E-IN009D-EN-P - June 2024 | Supersedes Publication 1732E-IN009C-EN-P - November 2021
Copyright © 2024 Rockwell Automation, Inc. All rights reserved.
">