Allen-Bradley End Cap Kit Guide d'installation
PDF
Download
Document
Advertisement
Advertisement
Bul. 140G2 DIR 1002011A1801 Version 01 - 140G2-K-ECM, 140G2-K-ECM4 End Cap Kit for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L Terminali anteriori Vorderseitige Anschlüsse Prises avant Terminales frontales 固定式断路器前接线端子 140G2-K, 140MG2-K Installation - Installazione - Installation - Installation Instalación - Instalação - 140G2-L, 140MG2-L WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. 70E requirements Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. 警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく ださい。適切なケース内に取付けてください。また、汚染物質がないことを 確認してください。 警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备 箱内。防止接触污染物。 Clack! Required Tools A B C xx lb-in xx Nm Length: Dia: 25mm (0.984") 10mm CH 8 (0.394") End Cap Screw Washer 140G2-K-ECM 3p 3 3 3 140G2-K-ECM4 4p 4 4 4 Publication 140G-IN220B-EN-P - May 2021 2 End Cap Kit for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L 1 2 CH 8 1 A ≥ 11mm (0.43") 3 = 10. 5 (≥ 0. mm 41") 4 2 5mm< t >10m m (0.2"< t >0.39 ") ≤ 12mm (0.47") ≤ 32.5mm (≤ 1.28") = 10. 5 (≥ 0. mm 41") 5mm< t >10m m (0.2"< t >0.39 ") 3 140G2-K, 140G2-L: ≥500V AC (≥250V DC) or REVERSE FEED Insulation Requirements ≤ 32.5mm (≤ 1.28") PH 1 1 2 ≥500V AC * (≥250V DC)* 3 4.4 lb-in 0.5 Nm 3 REQUIRED: 140G-K-TBP3 (3p) / 140G-KTBP4 (4p) The backshield is supplied with terminal cover *Breakers and accessories are tested for conformance to governing body standards with insulated cable or busbar. Any other configuration must be tested in the installation at the cost of the customer For Technical Support, visit rok.auto/support. Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec. Product certificates are located in the Rockwell Automation Literature Library: rok.auto/certifications. EEE Yönetmeliğine Uygundur. TM expanding human possibility AMERICAS EUROPE/MIDDLE EAST/AFRICA ASIA PACIFIC Publication 140G-IN220B-EN-P - May 2021 Copyright © 2021 Rockwell Automation, Inc. Al l Rights Reserved. Printed in USA. DIR 1002011A1801 (Version 01) (ECN000125637) - ECN000146519 ">

Public link updated
The public link to your chat has been updated.
Advertisement