Bul. 140G2
DIR 1002011A1802 Version 01 - 140G2-K-EXT3, 140G2-K-EXT4
Extended Front Terminals for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
Terminali anteriori prolungati
Vorderseitige verlängerte
Anschlüsse Prises avant prolongées
Terminales frontales prolongados
加长前接线端子固定式
140G2-K, 140MG2-K
Installation - Installazione - Installation - Installation Instalación - Instalação -
140G2-L, 140MG2-L
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
70E requirements
Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染物。
Clack!
Required Tools
A
B
C
D
E
xx lb-in
xx Nm
CH 8
140G-K-TBP3
3p Back Shield
140G-K-TBP4
4p Back Shield
140G2-K-EXT3 3p
1
-
140G2-K-EXT4 4p
-
1
Publication 140G-IN221B-EN-P - July 2021
Terminals
Phase Barriers
3
3
2
4
4
3
2
Extended Front Terminals for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
2
1
B
1
3
CH 8
4
Note: supplied
with end cap
kit or breaker
5
Publication 140G-IN221B-EN-P - July 2021
DIR 1002011A1802 (Version 01)
3
Extended Front Terminals for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
6
140G2-K, 140G2-L: ≥500V AC (≥250V DC) or REVERSE FEED Insulation Requirements
PH 1
1
2
≥500V AC *
(≥250V DC)*
3
REQUIRED: 140G-K-TBP3 (3p) / 140G-KTBP4 (4p)
4.4 lb-in
0.5 Nm
3
The backshield is supplied with terminal cover
*Breakers and accessories are tested for conformance
to governing body standards with insulated cable or
busbar. Any other configuration must be tested in the
installation at the cost of the customer
For Technical Support, visit rok.auto/support.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Product certificates are located in the Rockwell Automation Literature Library: rok.auto/certifications.
EEE Yönetmeliğine Uygundur.
TM
expanding human possibility
AMERICAS
EUROPE/MIDDLE EAST/AFRICA
ASIA PACIFIC
Publication 140G-IN221B-EN-P - July 2021
Copyright © 2021 Rockwell Automation, Inc. Al l Rights Reserved. Printed in USA.
DIR 1002011A1802 (Version 01)
(ECN000143548) - ECN000179670
">
