Bul. 140G2
DIR 1002011A1813 Version 01 - 140G2-K-MTL63, 140G2-K-MTL64
Cu Front Terminal Lugs (6 Cable) for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
Cu Terminali anteriori per cavi
Cu Vorderseitige Anschlüsse für Kabel
Cu Prises avant pour câbles
Cu Terminales frontales para cables
Cu 电缆的前端
Installation - Installazione - Installation - Installation Instalación - Instalação WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
70E requirements
Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染物。
140G2-K, 140MG2-K
140G2-L, 140MG2-L
Clack!
140G2-K-TBP3
3p Back Shield
140G2-K-TBP4
4p Back Shield
140G2-K-TC3H
3p High Terminal
Cover
140G2-K-TC4H
4p High Terminal
Cover
A
B
C
D
1
-
1
-
-
1
-
1
140G2-K-MTL63 3p
140G2-K-MTL64 4p
Publication 140G-IN217B-EN-P - March 2023
2
Cu Front Terminal Lugs (6 Cable) for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
Required Tools
Cu Lugs:
(6) 6 AWG...1/0 AWG
[(6) 16mm²...50 mm²]
Lenght
Dia.
6 mm
(0.28")
M5
CH 5
CH 8
xx lb-in
xx Nm
Lenght
25 mm
(0.984")
Dia.
Lenght
Dia.
M10
16 mm
(0.63")
3mm
(0.12")
PH 1
xx lb-in
xx Nm
140G2-K-MTL63 3p
140G2-K-MTL64 4p
Lug
Screw
Nut
Mounting screw
E
F
G
H
3
3
3
2
4
4
4
2
1
2
A
1
3p
G
2
B
2
4p
Publication 140G-IN217B-EN-P - March 2023
DIR 1002011A1813 (Version 01)
3
Cu Front Terminal Lugs (6 Cable) for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
3
CH 8
E
4
2
F
18 Nm
159 lb in
1
5
1
I
TOP VIEW
II
(FRONT
HOLES)
2
Ømax 10 mm
Ømax 0,39"
II
Cu
Stranded
MAX 1/0 AWG
MIN 6 AWG
MAX 50 mm2
MIN 16 mm2
Publication 140G-IN217B-EN-P - March 2023
min 15 mm
min 1,1"
I
(REAR
HOLES)
min 38 mm
min 1,5"
CH 5
Ømax 10 mm
Ømax 0,39"
Cu
Flexible
7 Nm / 62 lb in
7 Nm / 62 lb in
DIR 1002011A1813 (Version 01)
4
Cu Front Terminal Lugs (6 Cable) for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
6
PH 1
3p
C
H
4.4 lb-in
4p
0.5 Nm
D
For Technical Support, visit rok.auto/support.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Product certificates are located in the Rockwell Automation Literature Library: rok.auto/certifications.
EEE Yönetmeliğine Uygundur.
TM
expanding human possibility
AMERICAS
EUROPE/MIDDLE EAST/AFRICA
ASIA PACIFIC
Publication 140G-IN217B-EN-P - March 2023
Copyright © 2021 Rockwell Automation, Inc. A
l l Rights Reserved. Printed in USA.
DIR 1002011A1813 (Version 01)
ECN000263877
">
