Bul. 140G2
DIR 1002012A1603 Version 02 - 140G2-K-PB3L, 140G2-K-PB4L, 140G2-K-PB3H, 140G2-K-PB4H
Phase Barriers for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
Separatori di fase
Trennwande zwischen den Phasen
Sèparateurs de phase
Separadores de fase
相间隔板
140G2-K, 140MG2-K
Installation - Installazione - Installation - Installation Instalación - Instalação -
140G2-L, 140MG2-L
WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
70E requirements
Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染物。
Clack!
B
A
200mm
(7.87")
100mm
(3.94")
140G2-K-PB3L
140G2-K-PB4L
140G2-K-PB3H
140G2-K-PB4H
Publication 140G-IN231C-EN-P - November 2023
3p
4p
3p
4p
4
-
6
-
-
4
-
6
2
Phase Barriers for 140G2-K, 140G2-L 140MG2-K, 140MG2-L
1
Example with Front Terminals
2
2
1
A
A
3
B
Example with Spread Terminals
B
Publication 140G-IN231C-EN-P - November 2023
DIR 1002012A1603 (Version 02)
3
Phase Barriers for 140G2-K, 140G2-L, 140MG2-K, 140MG2-L
4
140G2-K, 140G2-L: ≥500V AC (≥250V DC) or REVERSE FEED Insulation Requirements
PH 1
1
2
≥500V AC *
(≥250V DC)*
3
4.4 lb-in
REQUIRED: 140G-K-TBP3 (3p) / 140G-KTBP4 (4p)
The backshield is supplied with terminal cover
0.5 Nm
3
*Breakers and accessories are tested for conformance
to governing body standards with insulated cable or
busbar. Any other configuration must be tested in the
installation at the cost of the customer
5 140G2-K-EXS3, 140G2-K-EXS4: ≥500V AC (≥250V DC) or REVERSE FEED Insulation Requirements
PH 1
≥500V AC *
(≥250V DC)*
4.4 lb-in
0.5 Nm
REQUIRED: 140G2-K-TC3S, 140G2-K-TC4S
Ordered separately
Refer to the IN233 for installation requirements
*Breakers and accessories are tested for conformance
to governing body standards with insulated cable or
busbar. Any other configuration must be tested in the
installation at the cost of the customer
For Technical Support, visit rok.auto/support.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Product certificates are located in the Rockwell Automation Literature Library: rok.auto/certifications.
EEE Yönetmeliğine Uygundur.
TM
expanding human possibility
AMERICAS
EUROPE/MIDDLE EAST/AFRICA
ASIA PACIFIC
Publication 140G-IN231C-EN-P - November 2023
Copyright © 2019 Rockwell Automation, Inc. Al l Rights Reserved. Printed in USA.
DIR 1002012A1603 (Version 02)
(ECN000154492) - ECN000xxxxxx
">
