Bul. 140G2
DIR 1000999R0803 Version 00- 140G2-N-EXT3, 140G2-N-EXT4, 140G2-N-EXSLI3, 140G2-N-EXSLO3, 140G2-N-EXS4
Front Terminals Extended and Spread for 140G2-N, 140G2-NS, 140MG2-N
Terminali anteriori prolungati e divaricati
Vorderseitige verlängerte und verbreiterte Anschlüsse
Prises avant prolongées et épanouies
Terminales frontales prolongados y separadores
用于固定式断路器的前侧端子或前侧扩展分布端子
Installation - Installazione - Installation - Installation Instalación - Instalação WARNING: To prevent electrical shock, disconnect from power source before
installing or servicing. Install in suitable enclosure. Keep free from contaminants.
70E requirements
Per prevenire infortuni, togliere tensione prima dell'installazione o
manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti.
WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur
Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem
passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden.
AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation
secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire
appropriée. Protéger le produit contre les environnements agressifs.
ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o
del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada.
Manténgalo libre de contaminantes.
ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a
instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de
contaminantes.
警告：感電事故防止のため、取付けまたは修理の際は電源から取り外してく
ださい。適切なケース内に取付けてください。また、汚染物質がないことを
確認してください。
警告：为了防止触电，在安装或维修之前必须先切断电源。安装在合适的设备
箱内。防止接触污染物。
140G2-N
140MG2-N
Clack!
140G2-NS
Clack!
Required Tools
A
B
D
C
E
F
G
xx lb-in
xx Nm
PH 1
PH 2
Terminal Phase Barrier
Insulator 3p Terminal Set
4p Terminal Set
140G2-N-PB_L
140G2-N-EXT3
3p
140G2-N-EXT4
4p
3
4
140G2-N-EXSLI3 3p
140G2-N-EXSLO3 3p
140G2-N-EXS4
4p
Publication 140G-IN186A-EN-P - December 2019
2
3
Phase Barrier Insulator
140G2-N-PB_H
1
1
1
1
1
2
2
3
1
1
1
xx lb-in
xx Nm
CH 8
Front Terminals Extended and Spread for 140G2-N, 140G2-NS, 140MG2-N
2
Example: 140G2-NS
1
2
Example: 140G2-N-EXT3 assembled to 140G2-NS
PH 1
CH 8
PH 2
B
CH 8 mm
3 Example: 140G2-N-EXSLI3 assembled to 140G2-NS
Example: 140G2-NS
4
PH 1
CH 8
PH 2
CH 8 mm
Publication 140G-IN186A-EN-P - December 2019
DIR 1000999R0803 (Version 00)
Front Terminals Extended and Spread for 140G2-N, 140G2-NS, 140MG2-N
3
5
FOR REFERENCE: Extended Terminals Recommended Cable Installation Torque
6
FOR REFERENCE: Spread Terminals Recommended Cable Installation Torque
For Technical Support, visit rok.auto/support.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Product certificates are located in the Rockwell Automation Literature Library: rok.auto/certifications.
EEE Yönetmeliğine Uygundur.
TM
expanding human possibility
AMERICAS
EUROPE/MIDDLE EAST/AFRICA
ASIA PACIFIC
Publication 140G-IN186A-EN-P - December 2019
Copyright © 2019 Rockwell Automation, Inc. Al l Rights Reserved. Printed in USA.
DIR 1000999R0803 (Version 00)
(ECN000127788)
">
