Allen-Bradley ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions

Installation Instructions
Original Instructions
ArmorBlock 5000 16-channel Configurable Digital I/O Module
Catalog Numbers 5032-CFGB16M12DR, 5032-CFGB16M12P5DR, 5032-CFGB16M12M12LDR
Topic
Page
About the Module
1
Install the Module
4
Set the Module Network Address
5
Install the Module Overlay
6
Mount the Module
6
Connect the Network, I/O, and Power Cables to the Module
8
Specifications
11
Additional Resources
11
About the Module
The ArmorBlock 5000® 16-channel configurable digital I/O module provides 16 channels that can be configured individually as input or output. The module has fast I/O ports and
standard I/O ports and can be configured for input time stamp, Sequence of Events (SOE), and Scheduled Output.
IMPORTANT
You must use this module with the Studio 5000 Logix Designer® application. See the ArmorBlock 5000 16-channel Configurable Digital I/O Module User
Manual, publication 5032-UM002, for firmware/software requirements.
See the Module Identification diagram to identify the external features of the module.
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain
this product. Users are required to familiarize themselves with installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably trained personnel in accordance with applicable code of
practice. If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
岤䠑㖈㸝鄳ծꂁ縨ծ乼⡲ㄤ絶䫡劥❡ㅷ⵸霼ꢓ靀劥俒咓⟄⿺  Ⱖ➭餴彂  鿈ⴔ⴩ⴀ涸剣Ⱒ霃㢊㸝鄳ծꂁ縨ㄤ乼⡲涸湱䎾俒咓կꤑ✫䨾剣鷓欽錞薴ծ岁䖒ㄤ叻ⲥ涸
湱Ⱒ銳宠⛓㢪欽䨪鵮䗳곢擿䜪㸝鄳ㄤ䱹絁霹僈կ
㸝鄳ծ靈侮ծ䫏鵘ծ⢪欽ծ絆鄳ծ䬒⽸ㄤ絶䫡瘝ぐ고乼⡲䗳곢歋絑鵂鷓䔲雲絅涸⚁⚌➃プ䭽撑鷓欽涸乼⡲錞薴㹊倶կ
㥵卓劢䭽撑ⵖ鸣㉁䭷㹁涸倰䒭⢪欽霪霃㢊ⴭ〳腊⠔䰀㹲霃㢊䲿⣘涸⥂䫡կ
ATENCIÓN: Antes de instalar, configurar, poner en funcionamiento o realizar el mantenimiento de este producto, lea este documento y los documentos listados en la sección Recursos adicionales acerca de la
instalación, configuración y operación de este equipo. Los usuarios deben familiarizarse con las instrucciones de instalación y cableado y con los requisitos de todos los códigos, leyes y estándares vigentes.
El personal debidamente capacitado debe realizar las actividades relacionadas a la instalación, ajustes, puesta en servicio, uso, ensamblaje, desensamblaje y mantenimiento de conformidad con el código de
práctica aplicable. Si este equipo se usa de una manera no especificada por el fabricante, la protección provista por el equipo puede resultar afectada.
ATENÇÃO: Leia este e os demais documentos sobre instalação, configuração e operação do equipamento que estão na seção Recursos adicionais antes de instalar, configurar, operar ou manter este produto. Os
usuários devem se familiarizar com as instruções de instalação e fiação além das especificações para todos os códigos, leis e normas aplicáveis.
É necessário que as atividades, incluindo instalação, ajustes, colocação em serviço, utilização, montagem, desmontagem e manutenção sejam realizadas por pessoal qualificado e especializado, de acordo com o
código de prática aplicável.
Caso este equipamento seja utilizado de maneira não estabelecida pelo fabricante, a proteção fornecida pelo equipamento pode ficar prejudicada.
ВНИМАНИЕ: Перед тем как устанавливать, настраивать, эксплуатировать или обслуживать данное оборудование, прочитайте этот документ и документы,
перечисленные в разделе «Дополнительные ресурсы». В этих документах изложены сведения об установке, настройке и эксплуатации данного оборудования.
Пользователи обязаны ознакомиться с инструкциями по установке и прокладке соединений, а также с требованиями всех применимых норм, законов и
стандартов.
Все действия, включая установку, наладку, ввод в эксплуатацию, использование, сборку, разборку и техническое обслуживание, должны выполняться
обученным персоналом в соответствии с применимыми нормами и правилами.
Если оборудование используется не предусмотренным производителем образом, защита оборудования может быть нарушена.
:
ACHTUNG: Lesen Sie dieses Dokument und die im Abschnitt „Weitere Informationen“aufgeführten Dokumente, die Informationen zu Installation, Konfiguration und Bedienung dieses Produkts enthalten, bevor Sie
dieses Produkt installieren, konfigurieren, bedienen oder warten. Anwender müssen sich neben den Bestimmungen aller anwendbaren Vorschriften, Gesetze und Normen zusätzlich mit den Installations- und
Verdrahtungsanweisungen vertraut machen.
Arbeiten im Rahmen der Installation, Anpassung, Inbetriebnahme, Verwendung, Montage, Demontage oder Instandhaltung dürfen nur durch ausreichend geschulte Mitarbeiter und in Übereinstimmung mit den
anwendbaren Ausführungsvorschriften vorgenommen werden.
Wenn das Gerät in einer Weise verwendet wird, die vom Hersteller nicht vorgesehen ist, kann die Schutzfunktion beeinträchtigt sein.
ATTENTION : Lisez ce document et les documents listés dans la section Ressources complémentaires relatifs à l’installation, la configuration et le fonctionnement de cet équipement avant d’installer, configurer,
utiliser ou entretenir ce produit. Les utilisateurs doivent se familiariser avec les instructions d’installation et de câblage en plus des exigences relatives aux codes, lois et normes en vigueur.
Les activités relatives à l’installation, le réglage, la mise en service, l’utilisation, l’assemblage, le démontage et l’entretien doivent être réalisées par des personnes formées selon le code de pratique en vigueur.
Si cet équipement est utilisé d’une façon qui n’a pas été définie par le fabricant, la protection fournie par l’équipement peut être compromise.
:
,
,
,
.
,
.
,
,
,
,
,
,
.
.
ATTENZIONE Prima di installare, configurare ed utilizzare il prodotto, o effettuare interventi di manutenzione su di esso, leggere il presente documento ed i documenti elencati nella sezione “Altre risorse”,
riguardanti l’installazione, la configurazione ed il funzionamento dell’apparecchiatura. Gli utenti devono leggere e comprendere le istruzioni di installazione e cablaggio, oltre ai requisiti previsti dalle leggi, codici e
standard applicabili.
Le attività come installazione, regolazioni, utilizzo, assemblaggio, disassemblaggio e manutenzione devono essere svolte da personale adeguatamente addestrato, nel rispetto delle procedure previste.
Qualora l’apparecchio venga utilizzato con modalità diverse da quanto previsto dal produttore, la sua funzione di protezione potrebbe venire compromessa.
DİKKAT: Bu ürünün kurulumu, yapılandırılması, işletilmesi veya bakımı öncesinde bu dokümanı ve bu ekipmanın kurulumu, yapılandırılması ve işletimi ile ilgili İlave Kaynaklar bölümünde yer listelenmiş
dokümanları okuyun. Kullanıcılar yürürlükteki tüm yönetmelikler, yasalar ve standartların gereksinimlerine ek olarak kurulum ve kablolama talimatlarını da öğrenmek zorundadır.
Kurulum, ayarlama, hizmete alma, kullanma, parçaları birleştirme, parçaları sökme ve bakım gibi aktiviteler sadece uygun eğitimleri almış kişiler tarafından yürürlükteki uygulama yönetmeliklerine uygun şekilde
yapılabilir.
Bu ekipman üretici tarafından belirlenmiş amacın dışında kullanılırsa, ekipman tarafından sağlanan koruma bozulabilir.
岤䠑✲갪㖈㸝酤ծ鏤㹁ծ乼⡲䧴笞隋劥欴ㅷ⵸锝⯓ꠖ隡姼俒⟝⟄⿺⴩倴 չⰦ➭顺彂պ畎眎⚥剣ꡠ㸝酤ծ鏤㹁莄乼⡲姼鏤⪓涸俒⟝կ⢪欽罏䗳갭擿䜪㸝酤ㄤꂁ箁䭷
爙⚛痗ざ䨾剣岁鋊ծ岁䖒ㄤ垥彋銳宠կ
⺫䭍㸝酤ծ锄侮ծ❜➰⢪欽ծ⢪欽ծ穉酤ծ䬒⽸ㄤ笞隋瘝⹛⡲鿪䗳갭❜歋䊺竤麔黟殹鎯箻涸➃㆞鹍遤⟄痗ざ黟欽涸㻜⡲岁鋊կ
㥵卓㼞鏤⪓欽倴ꬋ醢鸣㉁䭷㹁涸欽鸀儗〳腊剚鸣䧭鏤⪓䨾䲿⣘涸⥂隋⸆腊「䴦կ
POZOR: Než začnete instalovat, konfigurovat či provozovat tento výrobek nebo provádět jeho údržbu, přečtěte si tento dokument a dokumenty uvedené v části Dodatečné zdroje ohledně instalace, konfigurace
a provozu tohoto zařízení. Uživatelé se musejí vedle požadavků všech relevantních vyhlášek, zákonů a norem nutně seznámit také s pokyny pro instalaci a elektrické zapojení.
Činnosti zahrnující instalaci, nastavení, uvedení do provozu, užívání, montáž, demontáž a údržbu musí vykonávat vhodně proškolený personál v souladu s příslušnými prováděcími předpisy.
Pokud se toto zařízení používá způsobem neodpovídajícím specifikaci výrobce, může být narušena ochrana, kterou toto zařízení poskytuje.
UWAGA: Przed instalacją, konfiguracją, użytkowaniem lub konserwacją tego produktu należy przeczytać niniejszy dokument oraz wszystkie dokumenty wymienione w sekcji Dodatkowe źródła omawiające
instalację, konfigurację i procedury użytkowania tego urządzenia. Użytkownicy mają obowiązek zapoznać się z instrukcjami dotyczącymi instalacji oraz oprzewodowania, jak również z obowiązującymi kodeksami,
prawem i normami.
Działania obejmujące instalację, regulację, przekazanie do użytkowania, użytkowanie, montaż, demontaż oraz konserwację muszą być wykonywane przez odpowiednio przeszkolony personel zgodnie z
obowiązującym kodeksem postępowania.
Jeśli urządzenie jest użytkowane w sposób inny niż określony przez producenta, zabezpieczenie zapewniane przez urządzenie może zostać ograniczone.
OBS! Läs detta dokument samt dokumentet, som står listat i avsnittet Övriga resurser, om installation, konfigurering och drift av denna utrustning innan du installerar, konfigurerar eller börjar använda eller utföra
underhållsarbete på produkten. Användare måste bekanta sig med instruktioner för installation och kabeldragning, förutom krav enligt gällande koder, lagar och standarder.
Åtgärder som installation, justering, service, användning, montering, demontering och underhållsarbete måste utföras av personal med lämplig utbildning enligt lämpligt bruk.
Om denna utrustning används på ett sätt som inte anges av tillverkaren kan det hända att utrustningens skyddsanordningar försätts ur funktion.
LET OP: Lees dit document en de documenten die genoemd worden in de paragraaf Aanvullende informatie over de installatie, configuratie en bediening van deze apparatuur voordat u dit product installeert,
configureert, bediend of onderhoudt. Gebruikers moeten zich vertrouwd maken met de installatie en de bedradingsinstructies, naast de vereisten van alle toepasselijke regels, wetten en normen.
Activiteiten zoals het installeren, afstellen, in gebruik stellen, gebruiken, monteren, demonteren en het uitvoeren van onderhoud mogen uitsluitend worden uitgevoerd door hiervoor opgeleid personeel en in
overeenstemming met de geldende praktijkregels.
Indien de apparatuur wordt gebruikt op een wijze die niet is gespecificeerd door de fabrikant, dan bestaat het gevaar dat de beveiliging van de apparatuur niet goed werkt.
Rockwell Automation recognizes that some of the terms that are currently used in our industry and in this publication are not in alignment with the movement toward inclusive
language in technology. We are proactively collaborating with industry peers to find alternatives to such terms and making changes to our products and content. Please excuse the
use of such terms in our content while we implement these changes.
2
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
ATTENTION: This equipment is intended for use in a Pollution Degree 2 industrial environment, in overvoltage Category II applications (as defined in EN/IEC
60664-1), at altitudes up to 2000 m (6562 ft) without derating.
This equipment is not intended for use in residential environments and may not provide adequate protection to radio communication services in such
environments.
This equipment is supplied as enclosed equipment. It should not require additional system enclosure when used in locations consistent with the equipment
Enclosure Type Ratings. Subsequent sections of this publication may contain more information regarding specific enclosure type ratings, beyond what this
product provides that are required to comply with certain product safety certifications.
In addition to this publication, see:
• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1, for additional install requirements.
• NEMA Standard 250 and IEC 60529, as applicable, for explanations of the degrees of protection provided by different types of enclosure.
ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines
when you handle this equipment:
• Touch a grounded object to discharge potential static.
• Wear an approved grounding wriststrap.
• Do not touch connectors or pins on component boards.
• Do not touch circuit components inside the equipment.
• Use a static-safe workstation, if available.
• Store the equipment in appropriate static-safe packaging when not in use.
ATTENTION: Power to this equipment and all connected I/O must be supplied from a source compliant with the following:
• You must use (Isolated) SELV-listed power supplies for module power.
• Make sure that all connectors and caps are securely tightened to seal properly the connections against leaks and maintain IP enclosure type requirements.
• Use only a soft dry anti-static cloth to wipe down equipment. Do not use any cleaning agents.
• Use cables assembly suitable for the type rating of the Equipment.
ATTENTION:
1. You must limit the module power source to 10 A, max, at 18…30V DC.
2. Confirm that the external module power supply is adequately sized for all installed modules.
For example, if the total module power current draw, including current inrush requirements, is 5 A, you can use a module power supply that is limited to 5 A.
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
3
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Module Identification
Functional Earth A (1)
M12-style, D-coded network
connector (Link 1)
M12-style, D-coded network
connector (Link 2)
QR Code (3)
Removable IP switch cover
IP switch cover lock
Network address switches
M12-style, A-coded I/O
standard ports
M12-style, A-coded I/O
fast ports
5032-CFGB16M12DR
5032-CFGB16M12P5DR
Functional Earth B (2)
Mini-style, 4-pin power
connector (male)
(1)
(2)
(3)
Functional Earth B (2)
Mini-style, 4-pin power
connector (female)
Mini-style, 5-pin power
connector (male)
5032-CFGB16M12M12LDR
Functional Earth B (2)
Mini-style, 5-pin power
connector (female)
M12, L-coded power
connector (female)
Functional Earth A grounds the module EtherNet/IP™ communication circuitry, which is designed to mitigate the effect of noise on the network. The module requires a solid earth ground connection, either through a metal screw
to a grounded metal panel or through a wire. See Network Connectors on page 8 for connections.
Functional Earth B grounds the module I/O and power circuitries to mitigate the effect of noise on the network. Functional Earth B is internally connected to pin 5 of power connectors in 5032-CFGB16M12P5DR and
5032-CFGB16M12M12LDR. The module requires a solid earth ground connection, either through the mini-style 5-pin or M12 L-coded power patchcord, or through a wire to the screw point. See Power Connectors on page 9 for
connections.
The QR Code contains a link to the product webpage that provides details on the product such as lifecycle status and documentation.
Install the Module
To install the module:
• Set the Module Network Address
• Mount the Module
• Connect the Network, I/O, and Power Cables to the Module
4
M12, L-coded power
connector (male)
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Set the Module Network Address
The module reads the network address switches first to determine if the switches are set to a valid number. See the Values for Network Address Switches table for available values.
The module ships with the network address switches set to 999 and Dynamic Host Configuration Protocol (DHCP) enabled.
To set the network address, do one of the following:
• Adjust the network address switches.
• Use a DHCP server, such as Rockwell Automation BootP/DHCP.
• Retrieve the IP address from nonvolatile memory.
To adjust the network address switches, do the following:
1. Remove power from the module.
2. Use a small flat screwdriver or test pen to rotate the IP switch cover lock 90° counterclockwise to the unlock position.
The IP switch cover pops out slightly.
Lock position
Unlock position
3.
Remove the IP switch cover.
4.
Set the network address to a valid value.
Use a small flat screwdriver or test pen to rotate each network address switch and align the arrow with the desired number (0…9).
Network address switches
Network address switches set
to default value of 999.
5.
6.
Verify that the IP switch cover lock is in the unlock position, then replace the IP switch cover over the network address switches.
Press down on the IP switch cover and use a small flat screwdriver or test pen to rotate the IP switch cover lock 90° clockwise to the lock position.
Reapply power to the module.
IMPORTANT
• Do not rotate the IP switch cover lock more than 90° clockwise or counterclockwise.
• The IP switch cover lock should rotate smoothly between the lock and unlock positions.
• If the IP switch cover does not fit correctly or the lock cannot be rotated smoothly, check the lock opening for any debris.
• Verify that the IP switch cover is installed correctly to seal the network address switches against leaks and maintain IP enclosure type requirements.
Values for Network Address Switches
Value
Description
001
Sets the module IP address to 192.168.1.1.
This value is valid but not recommended as this IP address is typically used by network switches.
002…253
Sets the module IP address to 192.168.1.xxx (where xxx is the value of the network address switches).
Subnet mask is set to 255.255.255.0 and the gateway address is set to 0.0.0.0.
The module does not have a host name that is assigned to it or uses any Domain Name Server (DNS).
254
Sets the module IP address to 192.168.1.254.
This value is valid but not recommended as this IP address is typically used by network switches.
888
Resets the module to factory default settings.
999
The module checks to see if DHCP is enabled.
• If DHCP is enabled, the module requests for an IP address from a DHCP server. The DHCP server also assigns other network address parameters.
• If DHCP is not enabled, the module uses the IP address and other network address parameters that are stored in nonvolatile memory.
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
5
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Install the Module Overlay
If you are using the module configured in 8-point mode, you can add the 5032-OVRLAY-QTY30 adhesive overlay on the module to align the point numbering to an 8-point module. To
install the module overlay, do the following:
1. Peel off the overlay pieces from the liner.
2.
3.
4.
5.
Align the upper overlay piece, identified by a “C0” marking on the top left, along the connector marked “C0” on the module.
Align the lower overlay piece, identified by a “C2” marking on the top left, along the connector marked “C4” on the module.
Ensure that all four circular cutout areas of each overlay piece align with the module connectors and that the status indicators are not hidden.
Press the overlay into place.
Mount the Module
Use the two mounting holes to mount the module directly to a panel or machine. Mounting holes accommodate M4 screws. The recommended torque specification for the screws is
0.68 N•m (6 lb•in.).
Module top
Module bottom
M4 screw
M4 screw
Grounding plate
Flat washer
(optional)
See the Module Dimensions diagram to help you mount the module.
6
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Module Dimensions
Measurements are in millimeters (inches)
60 (2.36)
M4 screw
5032-CFGB16M12DR
32.7
(1.29)
28
(1.10)
31.8
(1.25)
5032-CFGB16M12P5DR
200
(7.87)
32.7
(1.29)
189.5
(7.46)
28
(1.10)
31.8
(1.25)
5032-CFGB16M12M12LDR
35.1
(1.38)
23.6
(0.93)
M4 screw
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
7
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Connect the Network, I/O, and Power Cables to the Module
Sealing caps are provided to cover the unused connectors on your module. See the Module Accessories table for the list of accessories that are provided with your module.
You can use the configuration tools available at rok.auto/systemtools, or see the following publications to help select suitable Rockwell Automation cable, patchcord, and
accessories:
• For network cables, see Ethernet Media Specifications Technical Data, publication 1585-TD001.
• For I/O and power cables, see Cordsets and Field Attachables Technical Data, publication 889-TD002.
• For IP switch cover and sealing caps, see ArmorBlock 5000 I/O Modules Technical Data, publication 5032-TD001.
• For marker cards (1492-MD6X9), see Preprinted and Custom-printed Marker Cards Selection Guide, publication 1492-SG009.
Connect the cables or patchcords that you have selected for your module to the appropriate ports.
Module Accessories
Item
Quantity Provided
IP switch cover
1
Network connector sealing cap
1
I/O connector sealing cap
4
Power connector sealing cap
1
Marker card — 9 markers per card, 6 x 9 mm (0.24 x 0.35 in.)
1
Network Connectors
M12-style, D-coded Connectors, Female
NET 1
1
5
4
2
3
View into connector
Pin
Value
1
Tx+
Description
Transmitter+
2
Rx+
Receiver+
3
Tx-
Transmitter-
4
Rx-
Receiver-
5
GND
Connector shell shield
Pin
Value
Description
1
Rx+
Receiver+
2
Tx+
Transmitter+
3
Rx-
Receiver-
4
Tx-
Transmitter-
5
GND
Connector shell shield
NET 2
3
2
5
4
1
View into connector
Some of the recommended network cables for daisy chains are 1585D-M4TBJM-x and 1585D-M4TBDM-x.
I/O Connectors
The ArmorBlock 5000 I/O Module has four fast I/O ports and four standard I/O ports.
Fast I/O Ports
(1)
Standard I/O Ports
C0
C1
C2
C3
C4
C5
C6
C7
C8
C9
C10
C11
C12
C13
C14
C15
Port Number
P0
P0
P1
P1
P2
P2
P3
P3
P4
P4
P5
P5
P6
P6
P7
P7
Configure as Digital Input
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Configure as Digital Output
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Channel Number
(1)
8
Channel numbers C0…C15 that are indicated on the module correspond to CH 0…CH 15.
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
M12-style, A-coded Connectors, Female
Fast ports (P0…P3)
1
2
4
3
5
View into connector
Standard ports (P4…P7)
1
2
4
3
Pin
Value
1
MSA SA+
Description
Sensor/Actuator power, sourced from MSA
2
I/O
Digital input or digital output
3
MSA-
Module/Sensor/Actuator power, GND
4
I/O
Digital input, or digital output
5
FE
Functional Earth B
Pin
Value
Description
1
LA SA+
Sensor/Actuator power, sourced from LA
2
I/O
Digital input or digital output
3
LA-
LA power, GND
4
I/O
Digital input or digital output
5
FE
Functional Earth B
5
View into connector
Power Connectors
The module receives its required power through the male connector on the left. Use the female connector on the right to daisy chain power from this module to another
ArmorBlock 5000 I/O module.
The module requires two 24V DC (nominal) supplies. These supplies are called the MSA power (Module/Sensor/Actuator) and the LA power (Local Actuator). The MSA power provides
power to the microprocessor, Ethernet, and fast ports including SA power (MSA SA+) portion of the module. The LA power provides power to the standard ports with 2 A power digital
outputs and SA power (LA SA+) portion of the module.
Internally, the MSA power and LA power are isolated from each other.
IMPORTANT
The maximum current that any module can carry is 10 A.
The maximum current that any pin on the mini-style power connectors can carry is 10 A.
The maximum current that any pin on the M12 L-coded power connectors can carry is 16 A.
Mini-style, 4-pin Connectors — 5032-CFGB16M12DR
Male Input
Female Output
4
2
2
4
3
1
1
3
View into connectors
Pin
Value
Description
1
LA+
Power source voltage, isolated power
2
MSA+
Module/Sensor/Actuator power, V+
3
MSA-
Module/Sensor/Actuator power, GND
4
LA-
Power source voltage, isolated power, GND
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
9
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Mini-style, 5-pin Connectors — 5032-CFGB16M12P5DR
Male Input
Female Output
1
5
5
1
2
4
4
2
3
3
View into connectors
Pin
Value
Description
1
LA-
Power source voltage, isolated power, GND
2
MSA-
Module/Sensor/Actuator power, GND
3
FE
Functional Earth B
4
MSA+
Module/Sensor/Actuator power, V+
5
LA+
Power source voltage, isolated power
M12, L-coded Connectors — 5032-CFGB16M12M12LDR
Male Input
Female Output
5
5
1
5032-CFGB16M12M12LDR
4
4
3
2
1
3
View into connectors
10
Pin
Value
1
MSA+
Description
Module/Sensor/Actuator power, V+
2
LA-
Power source voltage, isolated power, GND
3
MSA-
Module/Sensor/Actuator power, GND
4
LA+
Power source voltage, isolated power
5
FE
Functional Earth B
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
2
ArmorBlock 5000 16-channel Configurable Digital I/O Module Installation Instructions
Specifications
The following table lists a subset of the module specifications. For a complete list of specifications, see the ArmorBlock 5000 I/O Modules Technical Data, publication 5032-TD001.
Module Specifications
Attribute
Value
Temperature, operating
IEC 60068-2-1 (Test Ad, Operating Cold),
IEC 60068-2-2 (Test Bd, Operating Dry Heat),
IEC 60068-2-14 (Test Nb, Operating Thermal Shock):
-20 °C ≤ Ta ≤ +60 °C (-4 °F ≤ Ta ≤ +140 °F)
Temperature, ambient, max
60 °C (140 °F)
Enclosure type rating
Meets IP66, IP67, and IP69K (when marked), and Type 2 Indoor Use Only, with receptacle dust caps or cable termination
Voltage, power min
18V DC
Voltage, power max
30V DC
Current, MSA power, max per module
(no Digital I/O loads, no Sensor Voltage loads, and no
power daisy-chain loads)
100 mA @ 24V DC
Current, LA power, max per module
(no Digital I/O loads, no Sensor Voltage Loads, and no
power daisy-chain loads)
50 mA @ 24V DC
Current, MSA power plus LA power, max per module
(includes Digital I/O loads, and Sensor Voltage loads)
10 A
Galvanic isolation voltage
50V (continuous), Basic Insulation Type, between MSA power and field Ethernet connectors
50V Basic Insulation Type between MSA power and LA power
No isolation between individual I/O
Dimensions (HxWxD), approx
(including connectors)
200 x 60 x 32.7 mm (7.87 x 2.36 x 1.29 in.) — 5032-CFGB16M12DR, 5032-CFGB16M12P5DR
200 x 60 x 35.1 mm (7.87 x 2.36 x 1.38 in.) — 5032-CFGB16M12M12LDR
Weight, approx
0.33 kg (0.73 lb) — 5032-CFGB16M12DR, 5032-CFGB16M12P5DR
0.29 kg (0.64 lb) — 5032-CFGB16M12M12LDR
Additional Resources
These documents contain additional information concerning related products from Rockwell Automation.
Resource
Description
ArmorBlock 5000 I/O Modules Technical Data, publication 5032-TD001
Provides specifications for ArmorBlock 5000 I/O modules.
Describes how to configure, use, and troubleshoot ArmorBlock 5000 16-channel configurable digital
ArmorBlock 5000 16-channel Configurable Digital I/O Module User Manual, publication 5032-UM002 I/O modules.
EtherNet/IP Network Devices User Manual, publication ENET-UM006
Describes how to configure and use EtherNet/IP devices to communicate on the EtherNet/IP
network.
Ethernet Reference Manual, publication ENET-RM002
Describes basic Ethernet concepts, infrastructure components, and infrastructure features.
System Security Design Guidelines Reference Manual, publication SECURE-RM001
Provides guidance on how to conduct security assessments, implement Rockwell Automation
products in a secure system, harden the control system, manage user access, and dispose of
equipment.
Industrial Components Preventive Maintenance, Enclosures, and Contact Ratings Specifications,
publication IC-TD002
Provides a quick reference tool for Allen-Bradley® industrial automation controls and assemblies.
Safety Guidelines for the Application, Installation, and Maintenance of Solid-state Control,
publication SGI-1.1
Designed to harmonize with NEMA Standards Publication No. ICS 1.1-1987 and provides general
guidelines for the application, installation, and maintenance of solid-state control in the form of
individual devices or packaged assemblies incorporating solid-state components.
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
Provides general guidelines for installing a Rockwell Automation industrial system.
Product Certifications website, rok.auto/certifications
Provides declarations of conformity, certificates, and other certification details.
You can view or download publications at rok.auto/literature.
Rockwell Automation Publication 5032-IN002A-EN-P - September 2023
11
Rockwell Automation Support
Use these resources to access support information.
Technical Support Center
Find help with how-to videos, FAQs, chat, user forums, Knowledgebase, and product notification updates.
Local Technical Support Phone Numbers
Locate the telephone number for your country.
rok.auto/support
rok.auto/phonesupport
Technical Documentation Center
Quickly access and download technical specifications, installation instructions, and user manuals.
rok.auto/techdocs
Literature Library
Find installation instructions, manuals, brochures, and technical data publications.
rok.auto/literature
Product Compatibility and Download Center (PCDC)
Download firmware, associated files (such as AOP, EDS, and DTM), and access product release notes.
rok.auto/pcdc
Documentation Feedback
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
Waste Electrical and Electronic Equipment (WEEE)
At the end of life, this equipment should be collected separately from any unsorted municipal waste.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur
Allen-Bradley, ArmorBlock 5000, expanding human possibility, Factory Talk, Rockwell Automation, Studio 5000 Logix Designer, and TechConnect are trademarks
of Rockwell Automation, Inc.
EtherNet/IP is a trademark of ODVA, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 5032-IN002A-EN-P - September 2023
Copyright © 2023 Rockwell Automation, Inc. All rights reserved. Printed in Singapore.
PN-703747
">