Allen-Bradley 6300M Panel Monitors User Manual

ASEM 6300M Panel Monitors
Bulletin Number 6300M
User Manual
Original Instructions
ASEM 6300M Panel Monitors User Manual
Important User Information
Read this document and the documents listed in the additional resources section about installation, configuration, and operation of this equipment before
you install, configure, operate, or maintain this product. Users are required to familiarize themselves with installation and wiring instructions in addition to
requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by suitably
trained personnel in accordance with applicable code of practice.
If this equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.
In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this
equipment.
The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with
any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams.
No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual.
Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc., is prohibited.
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment,
which may lead to personal injury or death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property
damage, or economic loss. Attentions help you identify a hazard, avoid a hazard, and recognize the consequence.
IMPORTANT
Identifies information that is critical for successful application and understanding of the product.
These labels may also be on or inside the equipment to provide specific precautions.
SHOCK HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that dangerous
voltage may be present.
BURN HAZARD: Labels may be on or inside the equipment, for example, a drive or motor, to alert people that surfaces may
reach dangerous temperatures.
ARC FLASH HAZARD: Labels may be on or inside the equipment, for example, a motor control center, to alert people to
potential Arc Flash. Arc Flash will cause severe injury or death. Wear proper Personal Protective Equipment (PPE). Follow ALL
Regulatory requirements for safe work practices and for Personal Protective Equipment (PPE).
The following icon may appear in the text of this document.
Identifies information that is useful and can help to make a process easier to do or easier to understand.
2
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Table of Contents
Preface
Summary of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Additional Resources . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Chapter 1
Overview
Catalog Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Peripheral Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Approximate Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Chapter 2
Prepare for Installation
Unpack the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
UL/cUL Mark Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
European Union Directive Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Environment Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Environment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Hazardous Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Restricted Access Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Installation Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DC Power Supply Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Mounting Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Panel Cutout Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Required Tools and Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Chapter 3
Installation
Prepare the Panel Cutout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Install the Panel Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Connect the Peripheral Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Grounding and Bonding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Install the Ground Wire. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Connect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
For DC Powered Panel Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
For AC Powered Panel Monitors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Chapter 4
Configuration
Set the Panel Monitor Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Display Resolution Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Calibrate the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Touch Screen Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Field Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Adjust the On-screen Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
OSD Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
3
Table of Contents
OSD Menu Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Adjust the OSD Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Chapter 5
Maintenance
Clean Panel Monitor Surfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Required Cleaning Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Disconnect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Clean the Touch Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Clean the Exterior Surfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Clean the Bezel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Reconnect Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Shipping or Transporting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Dispose of the Panel Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Chapter 6
Troubleshooting
4
LED Status Indicators and OSD Buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Troubleshooting Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Preface
This user manual provides procedures to install, connect, operate, and troubleshoot your
ASEM™ 6300M panel monitor.
A general knowledge of automation technology is needed to understand and follow the
instructions in this publication.
Knowledge of monitors, personal computers (PCs), and the Microsoft Windows® operating
system (OS) is required to understand and follow the instructions in this publication.
Summary of Changes
This publication contains the following new or updated information. This list includes
substantive updates only and is not intended to reflect all changes.
Topic
Added optional remote video link (RVL) receiver and optional RVL transmitter publication
links within Additional Resources table
Updated accessories that are related to RVL within Accessories
Inclusive terminology change to “recommended” within Display Resolution Value section
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Page
6
12
25
5
Additional Resources
These documents contain additional information concerning related products from Allen
Bradley. You can view or download publications at rok.auto/literature.
Resource
Description
Provides basic installation guidelines and instructions for ASEM 6300M panel monitors.
ASEM 6300M Panel Monitors Installation Instructions, publication 6300M-IN001
Provides technical specifications about the ASEM 6300M industrial monitors.
ASEM 6300 Industrial Computer Specifications Technical Data, 
publication IC-TD003
Provides basic installation guidelines and instructions for ASEM 6300V RVL receivers.
ASEM 6300 Remote Video Link (RVL) Receiver Installation Instructions,
publication 6300V-IN004
Provides basic installation guidelines and instructions for ASEM 6300V RVL transmitters.
ASEM 6300 Remote Video Link (RVL) Transmitter Installation Instructions,
publication 6300V-IN005
Provides detailed instruction on the operation and troubleshooting for ASEM 6300V RVL
ASEM 6300 Remote Video Link (RVL) Receiver and Transmitter User Manual,
receivers and RVL transmitters.
publication 6300V-UM001
Provides general guidelines for installing a Rockwell Automation industrial system.
Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1
Safety Guidelines for the Application, Installation, and Maintenance of Solid-State Provides general guidelines for the application, installation, and maintenance of solidstate control.
Controls, publication SG-1.1
Provides declarations of conformity, certificates, and other certification details.
Product Certifications website, rok.auto/certifications
Describes how to configure and use EtherNet/IP devices to communicate on the
EtherNet/IP™ Network Devices User Manual, publication ENET-UM006
EtherNet/IP network.
Describes basic Ethernet concepts, infrastructure components, and infrastructure
Ethernet Reference Manual, publication ENET-RM002
features.
Provides guidance on how to conduct security assessments, implement Rockwell
System Security Design Guidelines Reference Manual, publication SECURE-RM001 Automation products in a secure system, harden the control system, manage user
access, and dispose of equipment.
Assists original equipment manufacturers (OEMs) with construction of panels, to help
UL Standards Listing for Industrial Control Products, publication CMPNTS-SR002 ensure that they conform to the requirements of Underwriters Laboratories.
American Standards, Configurations, and Ratings: Introduction to
Provides an overview of American motor circuit design based on methods that are
Motor Circuit Design, publication IC-AT001
outlined in the NEC.
Industrial Components Preventive Maintenance, Enclosures, and Contact Ratings Provides a quick reference tool for Allen-Bradley® industrial automation controls and
assemblies.
Specifications, publication IC-TD002
Designed to harmonize with NEMA Standards Publication No. ICS 1.1-1987 and provides
Safety Guidelines for the Application, Installation, and Maintenance of Solid-state general guidelines for the application, installation, and maintenance of solid-state
control in the form of individual devices or packaged assemblies incorporating solidControl, publication SG1.1
state components.
6
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter
1
Overview
Standard Profile, Stainless Steel Bezel
Low Profile, Aluminum Bezel
Low Profile, Aluminum-glass True Flat Bezel
The ASEM™ 6300M panel monitor family is available in various display sizes and resolutions.
There are options of either standard or low profile bezel units.
IP65 (model dependent) environmental protection makes ASEM 6300M panel monitors an
excellent match for wash-down applications such as food processing and life sciences.
Some ASEM 6300M panel monitors have long-distance capabilities, which means they can be
connected to a personal computer (PC) where both are up to 100 m (328 ft) apart.
ASEM 6300M panel monitors offer the following features:
• Available in standard and low profile bezels, with the latter available in aluminum,
aluminum glass True Flat, and stainless steel True Flat
• Available in standard and widescreen formats
• Analog resistive or projected capacitive (PCAP) touch screens, the latter for multi-touch
operation
• Available in display sizes between 8.4…24 inches
• Various resolutions to include: FHD, VGA, SVGA, SXGA, AND XGA
• Wide angle LCD viewing with light-emitting diode (LED) backlight technology
• Standard panel monitors offer the following:
- Two video ports, DVI-D and DisplayPort
- One USB HUB, Type B port, and up to three USB 2.0 Type A ports
• Certain models offer a USB 2.0 port on the front bezel (see Table 1 on page 8)
• Long-distance panel monitors offer the following:
- One remote video link (RVL) port
- Up to five USB 2.0 ports
• Certain models offer a USB 2.0 port on the front bezel (see Table 1 on page 8)
• 110/240V AC input power standard, 24V DC optional
• IP65 rating on panel monitors with aluminum, aluminum True Flat, and aluminum glass
True Flat bezels
• IP66K and IP69K (model dependent) ratings on panel monitors with stainless steel True
Flat bezels
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
7
Chapter 1
Overview
Catalog Numbers
This publication is applicable to ASEM 6300M panel monitors listed in Table 1
See the product label attached on the side of your panel monitor to identify your
specific catalog number.
.
Table 1 - Catalog Numbers
Touch
Display Screen Aspect Resolution Luminance
Catalog Number Size
Type Ratio (W x H)
cd/m2
6300M-xxxBAPS…
6300M-xxxDAPS…
6300M-xxxBBPS…
8.4
Resistive
4:3
800x600,
SVGA
400
Resistive
16:9
1280x800,
WXGA
400
10.1
6300M-xxxACPS…
PCAP
6300M-xxxCCPS…
16:9
1280x800,
WXGA
400
6300M-xxxBAPS…
6300M-xxxDAPS…
10.4
Resistive
4:3
800x600,
SVGA
4:3
1024x768,
XGA
600
Resistive
6300M-xxxDSPS…
12.1
16:9
6300M-xxxAXPS…
1280x800,
WXGA
400
6300M-xxxCXPS…
6300M-xxxACPS…
PCAP
6300M-xxxCCPS…
16:9b
1280x800,
WXGA
400
6300M-xxxBAPS…
Aluminum Glass
True Flat
15.0
Resistive
4:3
1024x768,
XGA
500
6300M-xxxDSPS…
6300M-xxxAAPS…
Resistive
6300M-xxxAXPS…
16:9
1920x1080,
FHD
400
15.6
PCAP
16:9
1920x1080,
FHD
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
400
Stainless Steel
True Flat,
IP69K Rating
Aluminum Glass
True Flat
No
No
No
Yes
No
Yes
No
No
Yes
No
No
Yes
No
Yes
No
Yes
No
No
Yes
No
Aluminum
6300M-xxxCAPS…
Yes
Yes
Aluminum
True Flat
Stainless Steel
True Flat,
IP69K Rating
6300M-xxxBSPS…
No
No
Yes
6300M-xxxBBPS…
Yes
Yes
Aluminum
True Flat
Stainless Steel
True Flat,
IP69K Rating
No
Yes
No
Aluminum
6300M-xxxDAPS…
8
No
Aluminum
6300M-xxxCAPS…
No
Yes
Yes
Stainless Steel
True Flat,
IP69K Rating
6300M-xxxBSPS…
6300M-xxxACPS…
No
Yes
6300M-xxxBBPS…
6300M-xxxCCPS…
No
Aluminum
6300M-xxxDBPS…
No
Yes
Aluminum
True Flat
6300M-xxxDAPS…
6300M-xxxCXPS…
Aluminum Glass
True Flat
400
6300M-xxxBAPS…
6300M-xxxDBPS…
Stainless Steel
True Flat,
IP69K Rating
Yes
Yes
Aluminum
6300M-xxxDBPS…
6300M-xxxAAPS…
Yes
Aluminum
6300M-xxxCAPS…
6300M-xxxBBPS…
No
Aluminum
True Flat
6300M-xxxAAPS…
6300M-xxxCXPS…
USB Port
Long
on
Distance
Front Bezel Model
Aluminum
6300M-xxxDBPS…
6300M-xxxAXPS…
Bezel
Type
Yes
No
No
Yes
No
No
Yes
Chapter 1
Overview
Table 1 - Catalog Numbers (Continued)
Touch
Display Screen Aspect Resolution Luminance
Catalog Number Size
Type Ratio (W x H)
cd/m2
6300M-xxxBAPS…
6300M-xxxDAPS…
17.0
Resistive
4:3
1280x1024,
SXGA
350
6300M-xxxAAPS…
Resistive
6300M-xxxAXPS…
16:9
1920x1080,
FHD
400
18.5
6300M-xxxACPS…
PCAP
6300M-xxxCCPS…
16:9
1920x1080,
FHD
500
6300M-xxxBAPS…
19.0
Resistive
4:3
1280x1024,
SXGA
300
6300M-xxxDSPS…
6300M-xxxAAPS…
Resistive
16:9
1920x1080,
FHD
300
21.5
6300M-xxxACPS…
PCAP
6300M-xxxCCPS…
16:9
1920x1080,
FHD
300
6300M-xxxAAPS…
No
Aluminum Glass
True Flat
Resistive
6300M-xxxAXPS…
16:9
1920x1080,
FHD
300
24.0
PCAP
16:9
1920x1080,
FHD
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
300
Stainless Steel
True Flat,
IP69K Rating
Aluminum Glass
True Flat
No
Yes
No
Yes
No
Yes
No
No
Yes
No
No
Yes
No
Yes
No
No
Yes
No
Aluminum
6300M-xxxCAPS…
6300M-xxxCCPS…
Stainless Steel
True Flat,
IP69K Rating
No
Yes
Aluminum
6300M-xxxCAPS…
6300M-xxxACPS…
Yes
No
Aluminum
True Flat
Stainless Steel
True Flat,
IP69K Rating
6300M-xxxBSPS…
Yes
No
Yes
6300M-xxxBBPS…
6300M-xxxCXPS…
Aluminum Glass
True Flat
No
No
No
Aluminum
6300M-xxxDAPS…
6300M-xxxCXPS…
Stainless Steel
True Flat,
IP69K Rating
Yes
Yes
Aluminum
6300M-xxxCAPS…
6300M-xxxAXPS…
Aluminum
True Flat
Stainless Steel
True Flat,
IP69K Rating
6300M-xxxDSPS…
6300M-xxxDBPS…
No
Yes
6300M-xxxBSPS…
6300M-xxxCXPS…
USB Port
Long
on
Distance
Front Bezel Model
Aluminum
6300M-xxxBBPS…
6300M-xxxDBPS…
Bezel
Type
Yes
No
No
Yes
No
No
Yes
9
Chapter 1
Overview
Peripheral Connections
IMPORTANT
To comply with EN 61326-1, all cable types must be shielded and must be
used only indoors, and USB cables must be less than 3 m (9.84 ft) in
length.
IMPORTANT
Before connecting or disconnecting peripheral cables from I/O ports,
verify that you are in a non-hazardous location.
The front USB port on your panel monitor is not for use in hazardous
locations. 
Only use the front USB port for installation and maintenance purposes.
Table 2 - Peripheral Connections
Standard Panel Monitor
9
Front Bezel View
7
Bottom View
1
6
10
2
3
Long-Distance Panel Monitor
4
5
Front Bezel View
7
9
Bottom View
1
6
10
8
5
Note No.
1
2
3
4
5
Cable Type
Earth Ground Screw
DisplayPort
DVI-D
USB Hub, Type B
USB 2.0, Type A (quantity of 3)
6
USB 2.0 (1)
7
USB 2.0 (2)
8
Remote Video Link (RVL) (3) Port
DC Powered Panel Monitors: DC 2-pole Connector
AC Powered Panel Monitors: AC Power
9
10
Required Attribute
—
Shielded
Unshielded
(1) Optional feature.
(2) Select catalog numbers offer a USB 2.0 port on the front bezel. See Table 1 on page 8 for a list of catalog numbers with this
feature.
IMPORTANT: This USB port is not for use in hazardous locations.
IMPORTANT: The USB port cover must be closed properly for IP65 protection.
(3) The RVL port requires a specific Ethernet cable type. See Table 4 on page 12 for applicable cables.
10
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter 1
Approximate Dimensions
Overview
Dimensions are shown in millimeters (inches). Dimensions are not intended to be used for
manufacturing purposes.
Table 3 - Approximate Dimensions [mm (in.)]
16:9 and 16:10 Aspect Ratio Panel Monitors
Side View
Front View
D
A
C
B
E
4:3 and 5:4 Aspect Ratio Panel Monitors
Side View
D
Front View
A
C
B
E
Display Aspect
Size Ratio
8.4
4:3
10.1
16:10
10.4
4:3
16:10
12.1
4:3
15.0
4:3
15.6
16:9
17.0
5:4
18.5
16:9
19.0
5:4
21.5
16:9
24.0
16:9
Bezel Type
Aluminum
Aluminum True Flat
Aluminum
Aluminum glass True Flat
Stainless steel
Aluminum
Aluminum True Flat
Aluminum
Aluminum glass True Flat
Aluminum
Stainless steel
Aluminum
Stainless steel
Aluminum
Aluminum glass True Flat
Aluminum
Stainless steel
Aluminum
Aluminum glass True Flat
Aluminum
Stainless steel
Aluminum
Aluminum glass True Flat
Aluminum
Aluminum glass True Flat
Dimensions
C
A
B
D
E
250 (9.84)
210 (8.27)
45 (1.77)
19 (0.75)
5 (0.2)
262.5 (10.33)
181 (7.13)
45 (1.77)
17.5 (0.69)
4.5 (0.18)
278.3 (10.96)
196.7 (7.74)
45 (1.77)
17.5 (0.69)
6 (0.24)
300 (11.81)
245 (9.65)
45 (1.77)
19 (0.75)
5 (0.2)
308 (12.13)
210 (8.27)
45 (1.77)
17.5 (0.69)
4.5 (0.18)
335 (13.19)
270 (10.63)
45 (1.77)
19 (0.75)
5 (0.2)
390 (15.35)
398 (15.67)
315 (12.4)
45 (1.77)
19 (0.75)
6 (0.24)
395 (15.55)
245 (9.65)
45 (1.77)
25 (0.98)
455 (17.91)
355 (13.98)
45 (1.77)
21 (0.83)
6 (0.24)
461 (18.15)
282 (11.1)
45 (1.77)
25 (0.98)
6 (0.24)
490 (19.29)
388 (15.28)
45 (1.77)
21 (0.83)
6 (0.24)
528 (20.79)
319 (12.56)
45 (1.77)
25 (0.98)
6 (0.24)
584 (23.00)
352 (13.86)
45 (1.77)
25 (0.98)
6 (0.24)
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
4.5 (0.18)
6 (0.24)
11
Chapter 1
Overview
Accessories
Various accessories are available for your ASEM 6300M panel monitor.
See Table 1 to identify which catalog numbers are long-distance models.
Table 4 - Remote Video Link (RVL) Cables for Long-Distance Panel Monitors
Description
Cat 5e
Shielded and Foiled
with
Unshielded Twisted Pairs
(SF/UTP) type
for fixed laying
Cat 5e SF/UTP type
for not guided
flex laying
Cat 6a S/FTP type
for fixed laying
Cable Length
15 m (49.2 ft)
20 m (65.6 ft)
30 m (98.4 ft)
40 m (131.2 ft)
50 m (164 ft)
5 m (16.4 ft)
10 m (32.8 ft)
15 m (49.2 ft)
20 m (65.6 ft)
25 m (82 ft)
30 m (98.4 ft)
35 m (114.8 ft)
40 m (131.2 ft)
45 m (147.6 ft)
50 m (164 ft)
100 m (328 ft)
Min Bend Radius
50.4 mm (2 in.)
94.5 mm (3.72 in.)
90 mm (3.54 in.)
Cat. No. 6300V15RVLFIXED
20RVLFIXED
30RVLFIXED
40RVLFIXED
50RVLFIXED
5RVLFLEX
10RVLFLEX
15RVLFLEX
20RVLFLEX
25RVLFLEX
30RVLFLEX
35RVLFLEX
40RVLFLEX
45RVLFLEX
50RVLFLEX
100RVLFIXED
Table 5 - Adapters
Description
DisplayPort™ to VGA active adapter
DisplayPort to DVI-D active adapter
DisplayPort to HDMI active adapter
Cat. No.
6200V-DPVGA2
6200V-DPDVI2
6200V-DPHDMI4K
For optimal performance, use only Allen Bradley-approved active DisplayPort
adapters.
Table 6 - Other Cables
Description
DisplayPort to DisplayPort cable
DVI cable
USB to USB touch screen cable
Cable kit: DVI and USB 2.0 (USB A type to USB B type)
Cable Length
2 m (6.5 ft)
2 m (6.5 ft)
2 m (6.5 ft)
DVI: 5 m (16.4 ft)
USB 2.0: 5 m (16.4 ft)
Cat. No.
6200V-DPCBL2M
6200V-DVICBL2M
6200V-USBCBL2M
6300V-5MDVIUSB
Table 7 - RVL Components
Description
ASEM RVL Receiver
ASEM RVL Transmitter
12
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Cat. No.
6300V-RVLDV-RX
6300V-RVLDV-TX
Chapter
2
Prepare for Installation
Follow the requirements and procedures within this section to help you plan and prepare for
installation of your ASEM™ 6300M panel monitor.
Unpack the Monitor
Before you unpack the monitor, inspect the shipping carton for damage. If damage is visible,
immediately contact the shipper and request assistance. Otherwise, proceed with unpacking.
Keep the original packing material in case the panel monitor must be you must
returned for repair or transported to another location.
Your panel monitor ships with the following items.
Table 8 - Parts List
Item
Hardware
Document
Compliance
Description
• Mounting clips (for panel mounting)
• DC power connector assembly kit (for DC powered panel monitors only)
• For non-hazardous applications:
6300M Industrial Panel Monitors Installation Instructions, publication 6300M-IN001
• For hazardous locations:
6300M Panel Monitors for Hazardous Locations Installation Instructions, publication 
6300M-IN002
UL/cUL Mark Compliance
Equipment with the UL/cUL mark complies with the requirements of UL 61010-1, UL 61010-2201, CSA C22.2 No. 61010-1, and CSA C22.2 No. 61010-2-201. A copy of the certificate of
compliance is available at rok.auto/certifications.
European Union Directive Compliance
This equipment meets the European Union Directive requirements when installed within the
European Union or EEA regions and have the CE marking. A copy of the declaration of the
conformity is available at rok.auto/certifications.
ATTENTION: This equipment is intended to operate in an industrial or control
room environment, which uses some form of power isolation from the public
low-voltage mains. Some computer configurations cannot comply with the EN
61000-3-2 Harmonic Emissions standard as specified by the EMC Directive of
the European Union.
All I/O cables must be used only indoors.
Rockwell Automation Publication 6300M-UM001B-EN-P - March 2023
13
Chapter 2
Prepare for Installation
Environment Information
ATTENTION: This equipment is intended for use in a Pollution Degree 2
industrial environment, in overvoltage Category II applications (as defined in
IEC 60664-1), at altitudes up to 2000 m (6561 ft) without derating.
This equipment is considered Group 1, Class A industrial equipment according
to IEC/EN 61326-1. Without appropriate precautions, there can be potential
difficulties with electromagnetic compatibility in other environments due to
conducted as well as radiated disturbance.
In addition to this publication, see the following:
• Industrial Automation Wiring and Grounding Guidelines, publication 1770-4.1,
for more installation requirements.
• UL 50, CSA C22.2 No. 94.1, and IEC 60529, as applicable, for explanations of the
degrees of protection provided by enclosures.
Environment Requirements
Follow these environment requirements to make sure that your 6300M panel monitor provides
service with excellent reliability.
• Your installation site:
- must have sufficient power,
- must be indoors
- must be in an non-hazardous location except where the monitor is rated for
hazardous locations (see Hazardous Locations on page 15), and
- must not expose your panel PC to direct sunlight.
• The ambient air temperature range must be between 0…50 °C (32…122 °F), and have a
temperature code of T5.
- The surrounding air temperature must not exceed this maximum temperature,
especially when mounted in an enclosure.
IMPORTANT
•
•
14
Your ASEM™ 6300M panel monitor can operate at a range of
extremes. However, the life span of any electronic device is
shortened if you continuously operate the monitor at its highest
rated temperature, which includes the touch screen and LCD
panel.
Your 6300M panel monitor can be stored in a surrounding air temperature range of 5…+60 °C (23…140 °F).
The relative humidity of the ambient air must be 20…90% noncondensing at 0…40 °C
(32…104 °F), and 20…80% noncondensing at 41…50 °C (105…122 °F).’
Rockwell Automation Publication 6300M-UM001B-EN-P - March 2023
Chapter 2
Prepare for Installation
Hazardous Locations
IMPORTANT
Your ASEM 6300M DC powered panel monitors for hazardous locations
are intended only for USA and Canada applications. These monitors are
suitable for use in Class I, Division 2 Groups A, B, C, D hazardous
locations, or only in non-hazardous locations, with a temperature code
of T5.
IMPORTANT
AC powered panel monitors cannot be used in hazardous locations.
WARNING: Explosion Hazard
• Substitution of any components can impair suitability for hazardous locations.
• This equipment is an open-type device and is meant to be installed in an
enclosure suitable for the environment such that the equipment is only
accessible with the use of a tool.
• Do not disconnect equipment while the circuit is live or unless the area is
known to be free of ignitable concentrations.
• Peripheral equipment must be suitable for the location where it is used.
• The front USB port on 6300M-xxxBA and 6300M-xxxBB monitors is not for use
in hazardous locations. Only use that front USB port for installation and
maintenance purposes.
• In the U.S., all wiring must be in accordance with Class I, Division 2 wiring
methods of Article 501 of the National Electrical Code, and in accordance with
the authority having jurisdiction.
• In Canada, all wiring must be in accordance with Section 18-1J2 of the
Canadian Electrical Code, and in accordance with the authority having
jurisdiction.
Restricted Access Locations
For hazardous locations, verify that restricted access locations meet these conditions for your
panel monitor:
• Access is gained only by service personnel or by users who have been instructed on the
reasons for restrictions to a location and about any precautions to be taken.
• Access is by using a tool, a lock and key, or other means of security controlled by the
authority responsible for the location.
Installation Requirements
DC Power Supply Requirements
Follow these DC power supply requirements for your 6300M DC powered panel monitor.
• The panel monitor must be powered with a voltage of 24V DC (18…32V DC SELV input
voltage range).
• The nominal output power must be 25% larger than the rated power of your panel
monitor.
• The output voltage rise time has to be less than 100 ms.
• Consider the working temperature and the thermal derating of the power supply.
• The inrush current of the panel monitor cannot exceed a peak current of 10 A and a
pulse width time of 400 µs..
IMPORTANT
In environments with electrical noise, use an isolated power source and
electromagnetic compatibility (EMC) filter to help provide a reliable
touch screen operation.
Use an analog resistive touch screen where you anticipate EMC noise.
Rockwell Automation Publication 6300M-UM001B-EN-P - March 2023
15
Chapter 2
Prepare for Installation
Power Consumption
The following table shows the power consumption in watts of your 6300M panel monitor.
See the product label on the back side of your panel monitor to determine its
catalog number.
Panel Monitor Display Information
Display Size
Resolution (W x H)
Aspect Ratio
1024 x 768, XGA
4:3
12.1
1280 x 800, WXGA
16:10
15
Power Consumption (Watts), Max (1)
6300M-xxxB
6300M-xxxD
18.1
22.7
13.2
18.4
15.3
20.5
1024 x 768, XGA
4:3
15.6
1920 x 1080, FHD
16:9
25.9
30.3
17
1280 x 1024, SXGA
5:4
22.8
27.7
18.5
1920 x 1080, FHD
16:9
28.2
33.3
19.0
1280 x 1024, SXGA
5:4
22.3
27.3
1920 x 1080, FHD
16:9
27.4
32.4
21.0
26.2
21.5
24
(1) Add 2.5 W of power consumption for any USB port that is used.
Mounting Requirements
Follow these requirements to mount your panel monitor.
• Choose a suitable mounting height.
• For optimal performance, mount your panel PC horizontally in a 0° vertical (upright)
position with the I/O ports facing downward as shown in Table 9.
• For hazardous locations, mount in the horizontal orientation and vertical (upright)
position with the I/O ports facing down Table 9.
• To help prevent overheating and to provide access to the I/O ports for cable
connections, provide minimum clearances as shown in Table 9 around the perimeter of
the outer frame and the back of the chassis.
Table 9 - Minimum Clearance and Positioning
Vertical Upright Position,
Side View
Horizontal Orientation,
Rear View
Y
X
X
Y
Z
Dimension Letter Minimum Clearance
X
7 cm (2.75 in.)
Y
10 cm (3.94 in.)
Z
7 cm (2.75 in.)
I/O Ports
Facing Downward
Panel Cutout Requirements
Follow these requirements to for the panel cutout.
• Disconnect all electrical power before you make the cutout.
• The mounting surface material must be 2…6 mm (0.08…0.24 in.) thick.
• For a uniform gasket seal, the roughness of the panel surface must not exceed 120
microns (Rz 120).
• Verify that the area around the panel is clear of obstructions.
16
Rockwell Automation Publication 6300M-UM001B-EN-P - March 2023
Chapter 2
•
Prepare for Installation
The panel cutout area is dependent upon the display size and format of your 6300M DC
powered panel monitor.
Table 10 - Panel Cutout Dimensions [mm (in.)]
Panel Cutout Area
B
A
Standard
B
A
Widescreen
Display Size
Format (1)
12.1
12.1
15
15.6
17
18.5
19
21.5
Standard
Widescreen
Standard
Widescreen
Standard
Widescreen
Standard
Widescreen
Dimension [mm (in.)] (2)
Dimension A
Dimension B
315 (12.4)
250 (9.84)
301 (11.8)
203 (7.99)
370 (14.57)
295 (11.61)
388 (15.28)
238 (9.37)
435 (17.13)
335 (13.19)
453 (17.83)
274 (10.79)
470 (18.5)
368 (14.49)
520 (20.47)
312 (12.28)
24
Widescreen
577 (22.71)
344 (13.54)
(1) Standard format is offered with an analog resistive touch screen. Widescreen format is offered with analog resistive and
projective capacitive (PCAP) touch screens.
(2) All dimensions are ± 1 mm (0.04 in.).
Required Tools and
Hardware
The following tools and hardware are required to install and connect your panel PC.
Required Tools and Hardware
• For ASEM DC powered panel monitors: a DC power supply per DC Power Supply Requirements on page 15
• For ASEM AC powered panel monitors: a three-prong, three-slot AC power cord that is rated IEC-320-C13
• Cutout tools appropriate for mounting material
• Safety glasses
• Torque limiting screwdriver with 1.5 mm hex key bit
• Wire stripper, cutter, and crimper tool
• Small screwdriver
• Adjustable torque screwdriver with M2 and M3 flat-blade screw bits
• Various peripheral cables (see Peripheral Connections on page 10 for required cable ratings and cable types)
Rockwell Automation Publication 6300M-UM001B-EN-P - March 2023
17
Chapter 2
Prepare for Installation
Notes:
18
Rockwell Automation Publication 6300M-UM001B-EN-P - March 2023
Chapter
3
Installation
Prepare the Panel Cutout
1. Disconnect all electrical power before you make the cutout.
2. Be sure you are complying with all actions that are listed in both
Panel Cutout Requirements on page 16 and Mounting Requirements on page 16.
3. Cut an opening in the mounting material according to the dimensions specified for your
model shown in Table 10 on page 17.
4. Clean the panel area of all debris and metal fragments.
Install the Panel Monitor
To ease installation, two people should install the panel monitor; one person to
hold it in place and the other to install the mounting clips.
1.
Make sure that the sealing gasket is positioned properly on the panel monitor.
IMPORTANT
All monitors have a gasket that forms a compression-type seal.
Do not use sealing compounds.
2. From the front of the panel, insert the panel monitor into the cutout as shown.
3. Slide the mounting clips into the holes on all four sides of the monitor as shown.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
19
Chapter 3
Installation
4. Use a hex key to tighten the mounting clips according to the sequence shown.
12.1, 15, and 17-in. Display Sizes
15.6 and 19-in. Display Sizes
8
1
1
10
3
5
4
I/O Ports
4
I/O Ports
6
2
7
3
7
18.5-in. Display Size
1
5
9
2
6
10
5
8
21.5 and 24-in. Display Sizes
12
3
13
10
1
5
12
7
7
I/O Ports
3
8
11
2
6
4
I/O Ports
4
9
8
11
6
2
9
14
5. Use a torque limiting screwdriver and 1.5 mm hex key bit, tighten the mounting clips to
a torque of 0.2 N•m (1.8 lb•in) in the tighten sequence performed in step 4.
IMPORTANT
The mounting clips must be tightened to a torque of 0.2 N•m
(1.8 lb•in). Doing so provides a proper seal and to help prevent
product damage. Allen-Bradley® assumes no responsibility for
water or chemical damage to the monitor or other equipment
within the enclosure because of improper installation.
6. Repeat step 8 at least three times until all mounting clips are torqued to 0.2 N•m
(1.8 lb•in).
7. Verify that the gasket is compressed uniformly against the panel.
If the gasket is not compressed uniformly: loosen the mounting clips by tightening
sequence, then repeat steps 5…7.
Connect the Peripheral
Cables
IMPORTANT
Before connecting or disconnecting peripheral cables from I/O ports,
verify that you are in a non-hazardous location before you connect or
disconnect any peripheral connections.
For ASEM 6300M panel monitors with a USB port on the front bezel: 
This USB port is not for use in hazardous locations. Only use the front
USB port for installation and maintenance purposes.
1.
Connect peripheral cables to the appropriate I/O ports of your panel monitor. See
Table 2 on page 10 for I/O port locations.
2. See the installation guides and user manuals for other components to properly connect
the free end of the peripheral cables.
To ease future disconnection and reconnection of peripheral cables, label
each peripheral cable with its panel monitor I/O port location.
20
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter 3
Grounding and Bonding
Installation
Whenever two connected pieces of equipment are far apart, it is possible that their ground
connections could be at a different potential level.
To overcome possible grounding problems, the following bonding methods are recommended:
• Bonding method 1: Connect the data cable shields to the equipotential bonding rail on
both sides before connecting the cable to the interfaces.
•
Install the Ground Wire
Bonding method 2: Use an equipotential bonding cable (16 mm2 or AWG 6) to connect the
grounds between your panel monitor and ASEM 6300P panel PC.
To install the ground wire, perform the following steps.
1. Turn off the main power switch or breaker.
2. Remove the ground screw, eyelet terminal, and washers from the bottom of your panel
monitor. See Table 2 on page 10 for the ground screw location.
3. For earth ground, install a grounding wire to the eyelet terminal.
a. Use a 2.5 mm2 (14 AWG) or larger external wire to the eyelet terminal.
Use a grounding wire with an insulation color that is approved by local inspection
authority.
b. Strip 5 mm (0.20 in.) from the covering at the end of the grounding wire.
c. Insert the stripped end of the grounding wire into the open end of the eyelet
terminal, and crimp it securely to the wire.
4. Reinstall the eyelet terminal and washers to the ground screw in the sequence shown.
1
2
3
4
5
Sequence No.
1
2
3
4
5
Description
Toothed washer
Eyelet terminal
Washer
Lock washer
Ground Screw
5. Tighten the ground screw to the monitor chassis.
Connect Power
For DC Powered Panel Monitors
WARNING: Explosion Hazard. For monitors that are used in hazardous
locations: Do not connect or disconnect when energized.
To maintain the product certifications, all ASEM 6300M DC powered panel monitors require a
safety extra low voltage (SELV) power supply. The power supply is internally protected against
reverse polarity. To minimize ground loop currents and noise, Allen-Bradley recommends that
DC powered panel monitors use only one grounded connection.
The DC power connector assembly that is shipped with your ASEM 6300M DC powered panel
monitor must be assembled. This connector assembly provides strain relief for the DC power
wires by reducing their movement. To assemble, wire, and install the DC power connector
assembly onto your panel monitor, perform the following steps.
IMPORTANT
Verify that you are in a non-hazardous location before you connect or
disconnect any power connection
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
21
Chapter 3
Installation
Figure 1 - DC Power Connector Assembly
B
A
C
G
F
E
D
H
Table 11 - DC Terminal Block Assembly
ions
5
3
4
3
4
1
2
5
Note No.
1
2
3
4
5
Description
DC+ (24V DC nominal) recommended power wire size
DC- (0V DC) recommended power wire size
Stripped wire length
Torque range to secure DC power wires
Torque value to install DC terminal block to product
Value
2.5 mm2 (14 AWG)
7 mm (0.275 in.)
0.5...0.6 N•m (0.37...0.4 lb•ft)
0.3 N•m (0.22 lb•ft)
1. Lay out the DC power connector assembly kit (A of Figure 1).
2. Insert the cable tie through the slots of the appropriate connector half (B of Figure 1)..
3. Verify that the stripped ends of each DC power wire is 7 mm (0.275 in.). If necessary,
adjust the stripped length.
IMPORTANT
DC power wires must be of stranded copper and certified for at
least 85 °C (185 °F) operation.
4. Insert each stripped end into the DC terminal block as shown in Table 11.
5. Tighten the screws on top of the terminal block assembly to the torque value listed in
Table 11.
6. Slide the connector half with the attached tie onto the end of the DC terminal block 
(C of Table 11).
7. Tighten the cable tie so it is snug against the terminal wires.
8. Use cutting pliers to cut the excess part of the cable tie (D of Figure 1).
9. Install the white label supplied with the kit (E of Figure 1).
The white label can be used for identification or other information.
10. Align and install the other connector clamp half to complete the assembly 
(F of Figure 1).
11. When it is installed correctly, both tabs of the clamp half lock into place
(G of Figure 1).
12. Connect the DC terminal block with the connector assembly to the chassis of your panel
monitor (H of Figure 1).
13. Torque the DC terminal block flange screws to the values in Table 11.
14. Connect the power to your DC powered panel monitor.
22
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter 3
Installation
The light-emitting diode (LEDs) status indicator on the front bezel illuminates and LED
status indicators on the underside of the panel monitor illuminate.
See LED Status Indicators and OSD Buttons on page 35 for LED status
indicator definitions.
For AC Powered Panel Monitors
All ASEM 6300M AC powered models are designed for use in an industrial or control room
environment that uses some form of power isolation from the public, low voltage ma
To connect AC power to your ASEM 6300M AC powered panel monitor, perform the following
steps.
1. Be sure the power switch on the underside of your panel monitor is set to ‘off’.
2. Connect the appropriate end of an AC power cord (not supplied) to the power input port
on your panel monitor.
3. Connect the other end of the power cable to an AC power source with an input voltage
of 100...240V AC, 50/60 Hz.
4. Flip the power switch on the panel monitor to ‘on’.
The light-emitting diode (LEDs) status indicator on the front bezel illuminates and LED
status indicators on the underside of the panel monitor illuminate.
See LED Status Indicators and OSD Buttons on page 35 for LED status
indicator definitions.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
23
Chapter 3
Installation
Notes:
24
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter
4
Configuration
Follow these guidelines and procedures to help you check and change the display resolution
and access and configure the on-screen display (OSD) for your ASEM™ 6300M panel monitor.
Set the Panel Monitor Type
Your ASEM 6300M panel monitor uses a (digital) flat-panel display. When driven by an analog
VGA interface, your panel monitor is connected as an analog device. As a result, some setup
screens can indicate that your panel monitor is operating as an analog device, rather than as a
digital or flat-panel device.
If you are using a Microsoft Windows® Plug and Play (PnP) operating system (OS): 
Your PC automatically detects the connected monitor type during the startup process. Setting
the panel monitor type is not necessary.
If the video card installed in your PC does not support PnP, you must set the monitor type
manually. To configure your monitor type:
1. Enable your video card through your OS.
2. Adjust the brightness and contrast that is described in Adjust the On-screen Display on
page 28.
Display Resolution Value
Flat-panel monitors are fixed-resolution devices. The image looks best when the panel
monitor operates at its recommended resolution. Recommended resolutions depend on the
catalog number of your panel monitor. For recommended resolutions, see the resolution value
for your particular catalog number in Table 1 on page 8.
Flat-panel monitors also have advanced scaling capabilities to make the display look as good
as possible while in another resolution value. If you switch the recommended resolution to
another resolution value, the display can appear slightly distorted due to the replication
techniques used to fill the full screen with an image.
To verify the display resolution or to change the display resolution, follow these steps:
From the Microsoft Windows OS desktop:
1. Navigate to Settings > Display.
2. Scroll down to ‘Display resolution’ within ‘Scale and Layout’ section.
3. Verify the ‘Display resolution’ pull-down is the ‘(Recommended)’ selection.
4. To change the recommended display resolution to another resolution value:
a. Choose another selection from the pull-down list.
The view refreshes and a popup window appears.
b. Select ‘Keep resolution’ or ‘Revert’ to reset back to the inherent resolution.
5. Close the Settings window at the top-right corner of the screen.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
25
Chapter 4
Configuration
Calibrate the Touch Screen Touch Screen Precautions
WARNING: The LCD touch screen can be difficult to read and use of this screen
could result in a potentially hazardous outcome. Do not use the LCD touch screen
under these circumstances:
• The LCD screen darkens.
• The backlight is not functioning properly.
WARNING: You must provide means to achieve a safe state during anomalies
and to help achieve that the system has adequate redundancy for critical
functions. Failure to follow these instructions can result in death, serious injury,
or equipment damage.
WARNING: The design of your system must take into account the possibility of
the LCD touch screen losing functionality and not being able to be used to
maintain or change control of your system. The touch screen cannot be the
single point of control of critical functions and is not intended to replace an Estop.
The design of your system should follow all applicable code and good
engineering practice. Factors to consider in the design of your system include
but are not limited to the following:
• The possibility of an unreadable LCD touch screen.
• The possibility of an inoperable LCD touch screen.
• Unexpected communication errors or delays.
• Operator error in the control of the system.
• Proper use of E-stops and other safety practices.
Field Calibration
ASEM 6300M panel monitors with an analog resistive touch screen use an eGalaxTouch driver
that can be field calibrated.
ASEM 6300M panel monitors with PCAP touch screens use the inherent Microsoft
Windows Human Interface Device (HID) driver and cannot be field calibrated.
To field calibrate your ASEM 6300M panel monitor with an analog resistive touch screen,
perform the following steps.
1. Access the e-GalaxTouch driver software from the PC connected to your panel monitor.
The eGalaxTouch: USB Controller menu appears.
2. Press the ‘Tools’ tab.
3. Press ‘4 Points Calibration’ from the ‘Tools’ tab.
A white screen appears with a red circle and cross-hairs in one of the corners.
4. Press and hold a finger in the center of the red circle.
26
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter 4
Configuration
Keep your finger pressed until the counter reaches 100.
5. Repeat step 4 for the other three red circles as they appear in each corner of the
screen. A confirmation box appears when the calibration is complete.
6. Press ‘OK’.
7. On Tools, press ‘Draw Test’.
8. Use your finger to draw on the screen to verify that the touch screen is calibrated
correctly.
9. Press ‘Clear’ to delete what was drawn.
10. Press ‘Quit’.
11. Press ‘Apply’ from the Tools tab to save your changes.
12. Press ‘OK’ to close the eGalaxTouch driver software.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
27
Chapter 4
Configuration
Adjust the On-screen
Display
Your ASEM 6300M panel monitor features an on-screen display (OSD) menu that allows you to
you to change various display settings to accommodate your installation site.
OSD Buttons
To navigate within the on-screen menu, use the buttons that are located on the underside of
your ASEM 6300M panel monitor.
Table 12 - OSD Buttons
Underside View
1
2
3 4
Note No.
Description
Function
1
+ (<—)
Increase the value of the selected control or selects the next menu item.
2
– (—>)
Decreases the value of the selected menu item or selects the previous menu item.
3
Menu/Select
Push once to enter the main menu
Push a second time to select a highlighted menu option, which can prompt a submenu
Push a third time to exit from the current menu (back option)
4
ESC (Exit)
Exits the menu.
OSD Menu Options
The following options with respective descriptions are available within the OSD menu:
Table 13 - OSD Menu Options
OSD Menu
Brightness/
Contrast
Color
Settings
Input
Source
Display
Settings
Other
Settings
Item
Description
Brightness
Set the value from 1 to 100
Contrast
Set the value from 1 to 100
DCR
Set the DCR (dynamic contrast ratio) to ‘on’ or ‘off
Color Temperature
Default value: 5700K
Red
Set the value from 1 to 100; default value: 50
Green
Set the value from 1 to 100; default value: 50
Blue
Set the value from 1 to 100; default value: 50
Auto select
The best active input source is automatically selected; default is ‘on’
DVI
Select which port is for DVI input; only available if ‘Auto select’ is set to ‘off’
DisplayPort
Select which port is for DisplayPort input; only available if ‘Auto select’ is set to ‘off’
Gamma
Adjust the gamma of the monitor; default value: ‘off (2.2)’
H. Position
Adjust the horizontal position of the monitor value from 1 to 100; default value: 50
V. Position
Adjust the vertical position of the monitor from 1 to 100; default value: 50
Clock
Adjust the time for a specific time zone or for daylight savings time
Phase
Adjust the signal timing of the panel monitor to match that of the graphics card
Aspect ratio
Resize the aspect ratio so that any image fits or fills the display screen
OSD transparency
Adjust the opaqueness of the OSD menu background
OSD H. Position
Adjust the OSD H. (horizontal) position of the monitor from 1 to 100; default value: 50
OSD V. Position
Adjust the OSD V. (vertical) position of the monitor from 1 to 100; default: 50
OSD timeout
Adjust the OSD timeout from 1 to 100; default value: 100
OSD rotation
Rotate the OSD orientation between portrait and landscape views; default value: landscape.
Factory reset
Reset all settings to the factory default values
Resolution
Information
H. frequency
V. frequency
Displays current setting of each item
V. total
28
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter 4
Configuration
Adjust the OSD Settings
To adjust the on-screen display settings, follow the steps below.
See Table 12 on page 28 for button locations and their function. 
See Table 13 on page 28 for available items and default values within the OSD
menu.
1.
2.
3.
4.
5.
Press the ‘Menu/select’ button on the underside, far right of your panel monitor.
The OSD menu appears on the display with ‘Brightness/Contrast’ as the active selection.
Settings within the selected settings menu activate in the second column.
Current values for each setting are shown within the third column.
Press the ‘Menu/select’ button to navigate to the next menu in the far left column.
Press the ‘+ (<-)’ button to decrease or the ‘(->+)’ button to decrease the values within
the current menu. See Table 13 on page 28 for setting definitions and default values.
Repeat steps 2 and 3 as needed.
Press the ‘Exit’ button to exit the OSD menu.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
29
Chapter 4
Configuration
Notes:
30
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter
5
Maintenance
Clean Panel Monitor
Surfaces
For optimal performance, it is important to periodically clean the surfaces of your ASEM™
6300M panel monitor.
ATTENTION: Before cleaning any surface of your ASEM 6300M panel monitor,
disconnect power from the panel monitor at the power source. Disconnecting
power eliminates touch screen objects from activating during equipment
washdowns.
Required Cleaning Supplies
The following cleaning supplies are required to clean the touch screen and surfaces of your
panel monitor.
ATTENTION: Do not perform a scrubbing action or use abrasive supplies
(such as abrasive brushes), abrasive cleansers, abrasive solvents, or highpressure washes on your panel monitor. Scrubbing and abrasive supplies can
damage the touch screen and surfaces of your panel monitor.
ATTENTION: When selecting a mild soap, read the product description label of
the mild soap. Be sure it is safe to apply on the product materials of your
panel monitor.
Table 14 - Required Cleaning Supplies
Required Cleaning Supplies
Clean, dry, non-abrasive cloths (such as a microfiber cleaning cloths)
Chamois or clean cellulose sponges
Vacuum
Mild, non-abrasive soap
Isopropyl alcohol
Disconnect Power
1.
Disconnect power from the monitor at the power source to eliminate touch screen
objects from activating when cleaning the surfaces of your panel monitor.
2. Disconnect all peripheral cables from your panel monitor.
Before disconnecting the peripheral cables, label each peripheral cable with
its panel monitor I/O port location.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
31
Chapter 5
Maintenance
Clean the Touch Screen
To clean the touch screen:
1. Perform both steps in Disconnect Power on page 31.
2. Use a clean, dry, non-abrasive cloth (such as a microfiber cloth) to gently wipe away
loose dirt or smudges.
3. If further cleaning is needed:
a. Dampen a clean, dry, non-abrasive cloth with a commercially available product
approved for touch screen surfaces.
4. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
Clean the Exterior Surfaces
1. Perform both steps in Disconnect Power on page 31.
2. For vent holes:
Vacuum dust and debris from all vent holes on the display and monitor chassis.
3. For all other exterior surfaces:
a. Apply a mild soap to a clean sponge or a clean, soft, damp cloth.
b. Gently wipe the surfaces of your panel monitor.
c. Dampen another clean, soft, cloth with water.
d. Gently wipe the surfaces of your panel monitor again.
e. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
Clean the Bezel
If your panel monitor is mounted properly in IP66 enclosures, perform the following steps to
remove paint, grease, and residue from the bezel.
1. Perform both steps in Disconnect Power on page 31.
2. To remove paint and grease:
a. Dampen a clean, soft cloth with isopropyl alcohol.
b. Gently wipe away any paint splashes or grease from the bezel.
ATTENTION: Do not allow the isopropyl alcohol to come into contact
with equipment labels. Contact with isopropyl alcohol can cause the
print on the label to smear.
c. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
3. To remove residue:
a. Apply a mild soap to a clean sponge or a clean, soft, damp cloth.
b. Gently wipe the surfaces of your panel monitor.
c. Dampen another clean, soft, cloth with water.
d. Gently wipe the surfaces of your panel monitor again.
e. Dry the display with a chamois or moist cellulose sponge to avoid water spots.
Reconnect Power
1. Reconnect all peripheral cables from your panel monitor.
2. Reconnect power from the monitor at the power source.
32
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter 5
Maintenance
Shipping or Transporting
IMPORTANT
Do not ship or transport the monitor when it is installed in a machine, panel,
or rack. To avoid damage to the monitor, you must uninstall the monitor and
place it in its original packing material before you ship it. Allen Bradley is not
responsible for damage to a monitor that is shipped or transported while
installed in a machine, panel, or rack.
To ship your panel monitor via common carrier or transport your panel monitor to another
location for service or any other reason:
1. Disconnect power from the monitor at the power source. This eliminates touch screen
objects from activating when cleaning the surfaces of your panel monitor.
2. Disconnect all peripheral cables from your panel monitor.
3. Remove the panel monitor from its machine, panel, enclosure, or rack.
4. Place your panel monitor in its original packing material.
Dispose of the Panel
Monitor
At the end of its life, collect the panel monitor separately from any unsorted
municipal waste.
You cannot dispose of panel monitor equipment like other waste material. Most computers
and panel monitors contain heavy metals that can contaminate the earth. Therefore, check
with local health and sanitation agencies for ways to dispose monitor equipment safely.
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
33
Chapter 5
Maintenance
Notes:
34
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
Chapter
6
Troubleshooting
LED Status Indicators and
OSD Buttons
When your ASEM™ 6300M panel monitor is powered on, various LED (light-emitting diode)
status indicators illuminate on the front bezel and on the underside of the chassis. Use these
LED status indicators to oversee the current state of and troubleshoot your panel monitor. Use
the OSD (on-screen display) buttons, to reset any states and navigate within menus.
Table 15 - Standard Panel Monitors
Underside View
Front Bezel,
Bottom Left
1
1
2
3 4
5
LED Status Indicators
Note No. Description
1
Video Signal
Color
Function
Green
Correct video signal input
Yellow
No video signal
OSD Buttons
Note No.
Description
Function
2
+ (<—)
Increase the value of the selected control or selects the next menu item.
3
– (—>)
Decreases the value of the selected menu item or selects the previous menu item.
4
Menu/Select
Push once to enter the main menu
Push a second time to select a highlighted menu option, which can prompt a submenu
Push a third time to exit from the current menu (back option)
5
ESC (Exit)
Exits the menu.
Table 16 - Long-Distance Panel Monitors
Underside View
Front Bezel,
Bottom Left
1
1
2
3
4
5
6
7 8
9
LED Status Indicators
Note No. Description
Color
Function
Green
Correct video signal input
1
Video Signal
Yellow
No video signal
2
Link
Green
The panel monitor is linked to a remote, RVL capable remote PC
3
Video
Flashing Yellow
The panel monitor is receiving streaming video from the remote PC
4
Run
Flashing Green
The remote PC is operating correctly
5
Power
Green
The RVL port is operating correctly
Buttons
Note No.
Description
Function
6
+ (<—)
Increase the value of the selected control or selects the next menu item
7
– (—>)
Decreases the value of the selected menu item or selects the previous menu item
8
Menu/Select
Push once to enter the main menu
Push a second time to select a highlighted menu option, which can prompt a submenu
Push a third time to exit from current menu (back option)
9
ESC (Exit)
Exits the menu
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
35
Chapter 6
Troubleshooting
Troubleshooting Table
The troubleshooting table below lists typical symptoms and possible actions to correct
problems that you can encounter when you use your ASEM 6300M panel monitor.
Table 17 - Troubleshooting Table
Symptom
No signal message
Screen is blank
Out of range message
Picture is scrambled
Action
Check the video cable connection between the panel monitor and PC.
The video mode could be out of range. 
Change to the recommended resolution; see Picture is not clear action.
Disable the screen saver on your PC.
Verify that the power cord is connected to your panel monitor.
Test the wall outlet by plugging in a properly functioning device.
Replace the suspected faulty cable or power cord on your panel monitor.
Have the panel monitor serviced.
Check the maximum resolution and the frequency on the video port of your PC.
The video mode could be out of range. 
Change to the recommended resolution as described in the Picture is not clear action.
Check the video cable connection between your panel monitor and PC.
Check the maximum resolution and the frequency of the video (DVI-D) port on your PC.
Verify that the display resolution is set to ‘(Recommended)’ and the refresh rate is set
correctly. From the Microsoft Windows® OS desktop:
1. Navigate to Settings > Display.
2. Scroll down to ‘Display resolution’ within ‘Scale and Layout’.
3. Verify the ‘Display resolution’ pull-down is the ‘(Recommended)’ selection.
In this example, ‘1920 x 1080 (Recommended)’ is selected.
Picture is not clear
4. Change the pull-down selection if ‘(Recommended)’ was not the current selection.
5. Choose ‘Keep selection’ within the popup window.
6. Scroll down to and click the ‘Advanced display settings’.
7. Confirm the refresh rate and adjust as necessary.
8. Close the Settings window.

Check the video cable connection between the panel monitor and the PC.
Minimize unnecessary accessories such as video extension cables.
Verify that the application scaling is set. From the Microsoft Windows OS desktop:
1. Navigate to Settings > Display.
2. Scroll down to ‘Scale and layout’.
3. Select ‘Advanced scaling settings’.
Applications appear blurry 4. Verify that ‘Let Windows try to fix apps so they’re not blurry’ is set to ‘On’.
5. Change the setting to ‘On’ if it was not the current selection.
6. Close the settings window.
The video mode could be out of range.
Change to the recommended resolution as described in the Picture is not clear action.
Image is not stable
Check for proper video cable installation. Replace the suspected faulty cable.
The video mode could be out of range.
Change to the recommended resolution as described in the Picture is not clear action.
Screen jitter or noisy video Check for proper video cable installation. Replace the suspected faulty cable.
Reroute the cables or replace suspected faulty cables.
Check the host PC and panel monitor grounding.
36
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
ASEM 6300M Panel Monitors User Manual
Notes:
Rockwell Automation Publication 6300M-UM001B-EN-P - June 2023
37
Rockwell Automation Support
Use these resources to access support information.
Technical Support Center
Local Technical Support Phone Numbers
Technical Documentation Center
Literature Library
Product Compatibility and Download Center
(PCDC)
Find help with how-to videos, FAQs, chat, user forums, Knowledgebase, and product
notification updates.
Locate the telephone number for your country.
Quickly access and download technical specifications, installation instructions, and user
manuals.
Find installation instructions, manuals, brochures, and technical data publications.
Download firmware, associated files (such as AOP, EDS, and DTM), and access product
release notes.
rok.auto/support
rok.auto/phonesupport
rok.auto/techdocs
rok.auto/literature
rok.auto/pcdc
Documentation Feedback
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the
form at rok.auto/docfeedback.
Waste Electrical and Electronic Equipment (WEEE)
At the end of life, this equipment should be collected separately from any unsorted municipal waste.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Allen-Bradley, ASEM, expanding human possibility, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
DisplayPort is a trademark of Video Electronics Standards Association.
EtherNet/IP is a trademark of ODVA, Inc.
Microsoft and Windows are trademarks of Microsoft Corporation.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752, İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur
Publication 6300M-UM001B-EN-P - June 2023
Supersedes Publication 6300M-UM001A-EN-P - December 2021
Copyright © 2023 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
">