Installation Instructions
Original Instructions
ASEM Wall-mount and DIN Rail Brackets for 6300B Box PCs and
6300T Box Thin Clients
Catalog Numbers 6300V-BDINA, 6300V-BDINN, 6300V-VBOOKN, 6300V-BWALLA
Topic
Page
Installation Requirements
1
Remove the Existing Bracket
2
For Wall-mount Placement
3
For DIN Rail-mount Placement
3
Complete the Installation
3
ATTENTION: Read this document and the documents that are listed in the Additional Resources section about installation, configuration, and
operation of this equipment before you install, configure, operate, or maintain this product. Users are required to familiarize themselves with
installation and wiring instructions in addition to requirements of all applicable codes, laws, and standards.
Activities including installation, adjustments, putting into service, use, assembly, disassembly, and maintenance are required to be carried out by
suitably trained personnel in accordance with applicable code of practice. If this equipment is used in a manner that is not specified by the
manufacturer, the protection that is provided by the equipment may be impaired.
Summary of Changes
This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.
Topic
Page
Update within Approximate Dimensions
2
Installation Requirements
Placement Requirements
The placement of your ASEM™ box PC or ASEM box thin client must:
•
Be at a suitable height.
•
Be secured to a flat level surface (such as a shelf or wall) if placed in an area where
vibration is present.
- Holes are provided on both sides of the box PC for side mounting installation and
on the bottom for an upright installation
•
Be mounted in a horizontal orientation and vertical (upright) position for the
following:
- For wall-mount: The I/O ports face must face upward and the ground screw must
be located on a lower mounting bracket tab.
- For DIN rail-mount: The I/O ports face must face forward and the ground screw
must be located on the bottom bracket tab.
IMPORTANT
•
Your ASEM box PC or ASEM box thin client generates heat.
Do not operate your ASEM box PC or ASEM box thin client in an
enclosure without the minimum clearances unless adequate
ventilation or other cooling methods are used to lower the
temperature within the enclosure.
Wall-mount Placement
Side View
I/O ports must face upward
Ground screw must be
located on a lower
mounting bracket tab
DIN Rail-mount Placement
Rear View
I/O ports must face forward
Ground screw
must be located
on the bottom
bracket tab
Have at least 76 mm (3 in.) of clearance at the front and rear of your ASEM box PC or ASEM box thin client and at least 20 mm (0.8 in.) of clearance on each side.
- This clearance provides adequate ventilation and lets you install and remove cable connections or peripheral components (such as storage drives).
Wall-mount and DIN Rail Brackets for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions
Approximate Dimensions
The following figures provide important information when planning the installation of your ASEM box PC or ASEM box think client. Dimensions are in millimeters (inches).
Figure 1 - Approximate Dimensions [mm (in.)]
DIN Rail-mount Bracket Installation
Wall-mount Bracket Installation
3.50
(0.14)
13.50
(0.53)
3.50
(0.14)
111.00
(4.33)
4 x Ø 4.50 (0.18)
4 x Ø 1.80 (0.07)
39.50
(1.56)
10.00
(0.39)
101.50
(4.00)
33.90
(1.33)
60.00
(2.36)
70.00
(2.76) 101.50
(4.00)
112.50
(4.41)
32.34
(1.27)
100.00
(3.94)
33.76
(1.33)
28.00
(1.10)
111.50
(4.39)
5.00
(0.20)
5.00
(0.20)
8.00
(0.31)
7.00
(0.28)
25.50
(1.00)
7.50
(0.30)
7.00
(0.28)
20.00
(0.79)
40.90
(1.61)
100.00
(3.94)
11.00
(0.35)
9.00
(0.35)
Tools and Hardware for Installation
The following tools are required for a successful installation.
For All Installations
For Wall Mount Installation
For DIN Rail Installation
• Safety glasses
• Four M4x20 stainless steel screws
• DIN rail
• Level
• Drill
• #2 Phillips screwdriver
• 4 mm drill bit
Remove the Existing Bracket
IMPORTANT
Before you proceed, you must: (1) properly shut down your ASEM box PC or ASEM box thin client as instructed in the user manual, (2) disconnect the
AC power cord from the electrical outlet, (3) disconnect all peripheral cables, and (4) disconnect the grounding wire from the grounding screw.
To remove the existing brackets from your box PC or thin client:
1.
2
Using a #2 Phillips screwdriver, remove the four screws from the existing bracket.
Rockwell Automation Publication 6300V-IN002B-EN-P - November 2022
Wall-mount and DIN Rail Brackets for 6300B Box PCs and 6300T Box Thin Clients Installation Instructions
For Wall-mount Placement
With your ASEM box PC or ASEM box thin client that is properly shut down and disconnected from AC power, perform the following steps for wall-mount placement.
1.
Using a #2 Phillips screwdriver, attach the wall-mount bracket to your ASEM box PC or ASEM box thin client with four screws (supplied).
2.
Level and mark the four mounting holes on the mounting surface. See Installation Requirements on page 1, and Approximate Dimensions on page 2 for proper
planning and installation.
Drill the four marked mounting holes into the mounting surface to accommodate four M4x20 stainless steel screws (not supplied).
With the I/O ports facing upward, secure your ASEM box PC or ASEM box thin client to the mounting surface with four M4x20 stainless steel screws.
3.
4.
I/O ports must face upward
Ground screw must be located on a lower mounting bracket tab
For DIN Rail-mount Placement
With your ASEM box PC or ASEM box thin client that is properly shut down and disconnected from AC power, perform the following steps for DIN rail-mount placement.
1.
Using a #2 Phillips screwdriver, attach the DIN rail-mount bracket to your ASEM box PC or ASEM box thin client with four screws (supplied).
I/O ports must face forward
Ground screw must be located on bottom mounting bracket tab
2.
3.
If you have not already done so, install the DIN rail (not supplied) in your desired location. See the installation instructions packed with your DIN rail,
Installation Requirements on page 1, and Approximate Dimensions on page 2 for proper planning and installation.
With the I/O ports facing forward, secure your ASEM box PC or ASEM box thin client on your DIN rail.
I/O ports must face forward
Ground screw must be located on bottom mounting bracket tab
Complete the Installation
4.
5.
6.
Reconnect peripheral cables to your ASEM box PC or ASEM box thin client.
Reinstall the ground wire to the ground screw.
Reconnect power to your ASEM box PC or ASEM box thin client.
Rockwell Automation Publication 6300V-IN002B-EN-P - November 2022
3
Additional Resources
This publication provides basic installation instructions. For more information, see the following Rockwell Automation publications at rok.auto/literature.
Resource
Description
ASEM 6300B Book Mount Box PCs and 6300T Book Mount Box Thin Clients Installation Guide, Provides detail on how to install your ASEM 6300B Book Mount Box PC or 6300T Book Mount Box
Thin Client.
publication 6300B-IN001
ASEM 6300B Book Mount Box PCs and 6300T Book Mount Box Thin Clients User Manual,
publication 6300B-UM001
Provides detail on how to install, configure, operate, and troubleshoot your ASEM 6300B Book
Mount Box PC or 6300T Book Mount Box Thin Client.
6300 Industrial Computer and Monitor Specifications Technical Data, publication IC-TD003 Provides technical specifications for 6300 industrial computers and monitors.
Product Certifications website, rok.auto/certifications
Provides declarations of conformity, certificates, and other certification details.
Waste Electrical and Electronic Equipment (WEEE)
At the end of life, this equipment should be collected separately from any unsorted municipal waste.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
For technical support, visit rok.auto/support.
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752, İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur
Allen-Bradley, ASEM, expanding human possibility, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 6300V-IN002B-EN-P - November 2022 | Supersedes Publication 6300V-IN002A-EN-P - November 2020
Copyright © 2022 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
*PN-683449*
PN-683449
Vendor Code: 80460042.01
DIR 10005914022 (Version 01)
">
