Dismantle Instructions
Original Instructions
Dismantle VersaView 6300M-240Ex VESA Monitors for Recycling and Recovery
Cat. No. 6300M-240EAVSFDN1S
Topic
Page
About This Publication
1
Important User Information
1
Required Tools
2
Dismantle Procedure
2
Summary of Changes
This publication contains the following new or updated information. This list includes substantive updates only and is not intended to reflect all changes.
Topic
Page
Added catalog number.
1
Replaced ASEM MV200 with VersaView 6300M-240Ex.
1, 2
About This Publication
This document describes how to dismantle your Allen-Bradley® VersaView® 6300M-240Ex VESA monitor for recycling or disposal in accordance with the European Union Ecodesign
Directive. This document does not provide information on monitor configuration or setup.
Important User Information
Throughout this manual, when necessary, we use notes to make you aware of safety considerations.
WARNING: Identifies information about practices or circumstances that can cause an explosion in a hazardous environment, which can lead to personal injury or
death, property damage, or economic loss.
ATTENTION: Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions
help you identify a hazard, avoid a hazard, and recognize the consequences.
SHOCK HAZARD: Labels can be on or inside the equipment, for example, a drive or motor, to alert people that dangerous voltage may be present.
BURN HAZARD: Labels can be on or inside the equipment, for example, a drive or motor, to alert people that surfaces can reach dangerous temperatures.
IMPORTANT
Identifies information that is critical for successful application and understanding of the product.
Dismantle VersaView 6300M-240Ex VESA Monitors for Recycling and Recovery Dismantle Instructions
Required Tools
These tools can be used to dismantle the monitor:
• #2 Phillips torque screwdriver
• Torx screwdriver
• Screwdriver
• 5 mm HEX driver for VGA and DVI connector
• Wire cutter
• Safety glasses
Dismantle Procedure
To dismantle the VersaView 6300M-240Ex VESA monitor, perform the following steps:
1. Remove the ten M3x6 Torx screws on the back panel of the VESA monitor.
2.
2
Lift and remove the back panel from the VESA monitor.
The back panel and VESA monitor remain connected by two cables.
3.
Remove the three screws on the VESA monitor that secure the cables and a metal plate.
4.
Cut the cable tie.
5.
Remove the metal plate and disconnect the two cables.
The back panel is now disconnected from the VESA monitor.
Rockwell Automation Publication 6300M-IN003B-EN-P - March 2022
Dismantle VersaView 6300M-240Ex VESA Monitors for Recycling and Recovery Dismantle Instructions
6.
Remove the nine M3x6 Torx screws that secure the metal riser.
7.
Remove the metal riser.
8.
Remove the three M3x6 Torx screws and two hexagonal nuts of the DVI-D port that secure the connector crossbar to the motherboard.
9.
Remove the connector crossbar.
10. Remove the eight M3x6 Torx screws that secure the two metal brackets.
11.
Remove both metal brackets.
12. Remove the eight M3x4 screws that secure the motherboard and power board.
13. Remove both boards.
Rockwell Automation Publication 6300M-IN003B-EN-P - March 2022
3
14. Remove the 13 Torx M3x4 screws of the display holder frame.
15. Remove the display holder frame.
WARNING: Do not try to separate the touch screen from the LCD display; they are glued together. Trying to separate them can break the glass and cause
personal injury.
16. With a screwdriver, pry the bezel away from the LCD display.
LCD Display and Bezel Shown Separated
Dispose or recycle the separated parts as is appropriate for your location.
Waste Electrical and Electronic Equipment (WEEE)
At the end of life, this equipment should be collected separately from any unsorted municipal waste.
Rockwell Automation maintains current product environmental compliance information on its website at rok.auto/pec.
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
For technical support, visit rok.auto/support.
Rockwell Otomasyon Ticaret A.Ş. Kar Plaza İş Merkezi E Blok Kat:6 34752 İçerenköy, İstanbul, Tel: +90 (216) 5698400 EEE Yönetmeliğine Uygundur
Allen-Bradley, expanding human possibility, Rockwell Automation, and VersaView are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Publication 6300M-IN003B-EN-P - March 2022 | Supersedes Publication 6300M-IN003A-EN-P - February 2022
Copyright © 2022 Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.
PN-XXXXXX-XX
DIR 1000xxxxxx (Version 00)
">
