Allen-Bradley 140G /Early Break Contacts Guide d'installation
PDF
Download
Document
Advertisement
Advertisement
Bul. 140G/140MG DIR 1000719R0640 Version 02 - 140G-G-EAB1B Early break contacts, for rotary handle operating mechanism for 140G-G, 140G-H, 140G-I, 140G-J Contatti anticipati all’apertura, per maniglia rotante Verfrüht kontakte für das Ausschaltung, für Drehhebelantrieb Contact anticipé permettant la ouverture, pour commande par poignèe rotative Contacto temprano para el disparo, para mando giratorio Installation - Installazione - Instalación Instalação WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Install in suitable enclosure. Keep free from contaminants. (Follow NFPA70E requirements). AVVERTENZA: Per prevenire infortuni, togliere tensione prima dell'installazione o manutenzione. Installare in custodia idonea. Tenere lontano da contaminanti. (Seguire i requisiti NFPA70E). WARNUNG: Vor Installations- oder Servicearbeiten Stromversorgung zur Vermeidung von elektrischen Unfällen trennen. Die Geräte müssen in einem passenden Gehäuse eingebaut und gegen Verschmutzung geschützt werden. (Befolgen Sie die Anforderungen nach NFPA70E). AVERTISSEMENT: Avant le montage et la mise en service, couper l'alimentation secteur pour éviter toute décharge. Prévoir une mise en coffret ou armoire appropriée. Protéger le produit contre les environnements agressifs. (Vous devez respecter la norme NFPA70E). ADVERTENCIA: Desconéctese de la corriente eléctrica, antes de la instalación o del servicio, a fin de impedir sacudidas eléctricas. Instálelo en una caja apropiada. Manténgalo libre de contaminantes. (Cumpla con los requisitos NFPA70E). ATENÇÃO: Para evitar choques, desconectar da corrente elétrica antes de fazer a instalação ou a manutenção. Instalar em caixa apropriada. Manter livre de contaminantes. (Cumpra as exigências da norma NFPA70E). 140G-G 140G-I 1 CLACK 警告:感電事故防止のため、取付けまたは修理の際は電源から取り外してく ださい。適切なケース内に取付けてください。また、汚染物質がないことを 確認してください。(NFPA70Eの要件に従ってください) 警告:为了防止触电,在安装或维修之前必须先切断电源。安装在合适的设备 箱内。防止接触污染物。符合NFPA70E要求) 140G-H 140G-J 11 CLACK 1 Microswitch Carter DIR 1000719R0640 Version 02 2 3 FOR CABLES ON RIGHT SIDE ONLY FOR CABLES ON LEFT SIDE ONLY 4 FOR CABLE ON RIGHT FOR CABLE ON LEFT DIR 1000719R0640 Version 02 (2) 6 FOR CABLE ON RIGHT ONLY 147 137 137 147 5 EARLY BREAK 148 S4/4 EARLY BREAK 138 S4/3 138 148 Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc. Trademarks not belonging to Rockwell Automation are property of their respective companies. Rockwell Automation maintains current product environmental compliance information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/ sustainability-ethics/product-environmental-compliance.page Publication 140G-IN088C-MU-P - September 2015 DIR 1000719R0640 Version 02 (L8832) - B0301 Copyright © 2015 Rockwell Automation, Inc. All Rights Reserved. Printed in Italy. ">

Public link updated
The public link to your chat has been updated.
Advertisement