Lighting Contactor (Mechanically and Electrically Held)
(Cat 500LG_)
prevent electrical shock, disconnect from power source before installing or servicing. Follow NFPA 70E requirements.
WARNING To
Install in a suitable enclosure. Keep free from contaminants.
Bulletin 500LG lighting contactor installation must be performed by a "Qualified Person" as defined by the National
Electrical Code.
NOTICE
To prevent malfunction or shortened life, protect the 500LG lighting contactor from construction grit and metal chips.
The Bulletin 500LG lighting contactor is available in either electrically-held (Figure 1) or mechanically-held (Figure 2) configurations.
500
LG
Figure 1: Electrically-Held
Figure 2: Mechanically-Held
Main Base
The base of the lighting contactor has provisions to accept up to 12 power poles where 12 N.O. contacts are possible or any
combinations of N.O. and N.C. Positions 1 through 4 on the base can be configured to either normally open (N.O.) or normally closed
(N.C.) while positions 5 and 6 can only be configured as normally open (N.O.).
Power Pole
Power poles are available in either single pole (500LG-1PCK) or double poles (500LG-2PCK).
Auxiliary Contact
The auxiliary contact blocks are available in either single pole (500LG-141C) or double poles (500LG-142C) contact. Auxiliary contact
can be installed on either side of the base. When installed on the RIGHT side, the auxiliary contact functions as a N.C. contact. When
installed on the LEFT side, the auxiliary contact functions as a N.O. contact.
Control Module Kits
Control module kits enable conversion of an electrically held contactor to a mechanically held contactor. These kits are available in either
2-wire or 3-wire control versions in a variety of voltages. See renewal parts section (page 5) for catalog number.
NOTICE
The control module is available up to 277V maximum. For control voltage greater than 277V, use a control transformer.
Mounting Position
NOTICE
Mount lighting contactor in the vertical position only as shown below.
A maximum of 12 poles may be installed on the base. Positions "1" thru "4" on the base may be configured as either
normally open "N.O." or normally closed "N.C.", while positions "5" and "6" may be configured as "N.O." only.
Position "1"
Position "2"
Position "3"
Position "4"
10 - 15 lb-in
Position "5"
Position "6"
G
0L
50
500LG
Power Pole Removal
1 Remove power pole block by inserting screwdriver into the plastic clip
and pull it out to release the power pole block from the base.
Clip
LG
500
Power Pole Installation
N.C. Power Pole Installation
N.O. Power Pole Installation
1 Install the power pole
1 Rotate the power pole block
180 degrees to convert
the contact blocks from
N.C. to N.O.
block by sliding
foot into slot from
the N.C. indicator
side.
1
2 Pull clip, position
power pole block
onto the base,
and release.
1
2
2
2 Install the power pole
CLICK
block by sliding
foot into slot from
the N.O. indicator
side.
LG
500
500
LG
CLICK
3
3 Pull clip, position
power pole block
onto the base,
and release.
Auxiliary Installation
Auxiliary Removal
A 3-wire mechanically-held lighting contactor utilizes one N.O. and one N.C. auxiliary contacts. A 2-wire mechanically-held utilizes one
N.C. auxiliary contact installed on the right side.
1
Insert one end of auxiliary.
2
Snap other end in place.
1
Slide flat screwdriver
into clip of auxiliary
contact and lift.
2
1
500
LG
500
LG
CLICK
(2)
Coil Replacement
1
For mechanically-held contactors, remove all wires from the
control module and remove the coil cover along with the
control module.
or
2
For electrically-held contactors, remove the coil cover.
500
500
LG
LG
3 Remove old coil assembly.
4 Replace with new coil.
Old
New
For mechanically-held contactor,
For electrically-held, re-install coil
5 assembly and cover.
6 re-install the control module and cover.
OR
the contactor manually, using
7 Operate
manual operating tabs on the side.
Check that the latch and latch cover
at the bottom are still properly installed.
The mechanically-held contactor must
latch when tabs are pushed forward and
must unlatch when pushed again.
6
500
500
LG
LG
7 - 12 lb-in
7 - 12 lb-in
7
7
NOTICE
For mechanically-held contactors, latch and control module must be used together to ensure proper operation. Failure to do so will
void warranty. Follow the control module instruction sheet 42052-193-01.
(3)
Wiring Diagram
TABLE A: 2-WIRE CONNECTION DIAGRAM
TABLE B: OPTIONAL WIRING AND PILOT DEVICES FOR MECHANICALLY-HELD CONTACTOR, 2-WIRE CONTROL
ELECTRONIC MODULE
NOT
USED
A1
P2
P3
P4
P5
C
2
FUSE
ON
C
FUSE
4
A2
C
P
COIL
VOLTAGE
(LEFT AUX.)
C
4
3
A1
2
R
(RIGHT AUX.)
N
G
3
CONTROL
VOLTAGE
P1 P2 P3 P4 P5
P1
P
OFF
ELECTRONIC
MODULE
OFF-ON
OFF-AUTO
SELECTOR SWITCH
(OPTIONAL AUX.)
(OPTIONAL AUX.)
OFF ON
N
A2
C
ELECTRONIC MODULE
N
P1
P3
P4
P5
C
C
FUSE
1
4
A2
C
P
COIL
VOLTAGE
(LEFT AUX.)
3
A1
2
R
C
4
ON
TABLE G: CONTACT BLOCK POSITIONS
2
FUSE
AUTO
N
(RIGHT AUX.)
500LG(MECHANICALLY-HELD, 2-WIRE)
3
G
N
HAND
P
CONTROL
VOLTAGE
P
HAND-OFF-AUTO
ON-OFF-AUTO
SELECTOR SWITCH
3
CONTROL
VOLTAGE
P2
OFF
OFF
COIL
VOLTAGE
P
N
REFER TO TABLE A, C OR E FOR
CONTROL CONNECTION DIAGRAM
TABLE D: OPTIONAL WIRING AND PILOT DEVICES FOR MECHANICALLY-HELD CONTACTOR, 3-WIRE CONTROL
TABLE C: 3-WIRE CONNECTION DIAGRAM
ELECTRONIC MODULE
LOAD
P1
P2
P3
P4
P5
2
A1
C
4
(LEFT AUX.)
N
(RIGHT AUX.)
(LEFT AUX.)
ON
C
3
C
FUSE
4
A2
(RIGHT AUX.)
C
P
A1
2
R
ON
CONTROL
VOLTAGE
ON-OFF
PUSHBUTTON
FUSE
N
A2
C
TABLE E: ELECTRICALLY-HELD
P5
2
FUSE
N
C
4
(LEFT AUX.)
C
3
C
FUSE
4
A2
C
P
A1
(RIGHT AUX.)
2
TABLE F: OPTIONAL WIRING AND PILOT DEVICES FOR ELECTRICALLY-HELD CONTACTOR
CONNECTION DIAGRAM
ON
R
1
ON-OFF
PUSHBUTTON
6
L1
FUSE
ON
OFF
OFF
FUSE
A1
2
C
L2
A2
C
1
2
ON
(RIGHT AUX.)
OFF
C
G
ON
A1
L1
C
A2
COIL
VOLTAGE
L2
R
OFF ON
1
L1
FUSE
FUSE
A1
C
L2
A2
2
2
OFF
C (RIGHT AUX.)
G
500LG(ELECTRICALLY-HELD)
ON
R
HAND-OFF-AUTO
ON-OFF-AUTO
SELECTOR SWITCH
6
P4
N
(OPTIONAL AUX.)
5
(OPTIONAL AUX.)
5
P3
COIL
VOLTAGE
500LG(MECHANICALLY-HELD, 3-WIRE)
3
(LEFT AUX.)
4
P2
R
4
N
P1
C
P
ON
P
OFF ON
OFF (RIGHT AUX.)
G
CONTROL
VOLTAGE
ELECTRONIC MODULE
N
CONTROL
VOLTAGE
COIL
VOLTAGE
P
OFF-ON
SELECTOR SWITCH
3
3
OFF - ON
OFF - AUTO
SELECTOR SWITCH
3
3
N.O. ONLY
3
G
2
ELECTRONIC
MODULE
P1 P2 P3 P4 P5
C
P
OFF
2
1
(OPTIONAL AUX.)
N.O. OR N.C.
1
(OPTIONAL AUX.)
OFF
COIL
VOLTAGE
LINE
L1
FUSE
OFF
HAND AUTO
FUSE
A1
2
C
1
C (RIGHT AUX.)
L2
A2
2
OFF
G
1 Remote device
2 Additional control circuit overcurrent protection may be required when the control circuit conductors extend beyond the
enclosure. Refer to National Electrical Code.
3 Coil and control voltages may not be the same. check the voltage of the electronic module and coil before applying power.
4 For additional contact blocks for pilot lights or other signal indications, order two DSPT (500LG-142C) auxiliary contact blocks.
2-wire or 3-wire mechanically held lighting contactor comes standard with one SPST (500LG-141C) or two SPST (500LG-141C)
respectively.
(4)
Short Circuit Current Rating
Maximum horsepower rating(Normal Duty)
Available Symmetrical Amperes RMS
Maximum
Breaker Size
(amps)
Short Circuit
Current Rating
(amps)
At AC Service Voltage
Across the line AC
motor starting
110 - 120VAC
220 - 240VAC
30
30
40
40
14,000
10,000
5,000
5,000
250V
277V
480V
600V
600V or less
440 - 480VAC
550 - 600VAC
Class J
Class RK1
Maximum Fuse
100,000
50,000
30
PH
HP
FLA
1O
1
16
3O
1.5
12
1O
2
12
3O
5
15.2
1O
5
14
3O
1O
10
5
14
11.2
3O
15
17
Renewal Parts
Component
Voltage
Cat. No.
Coil
115 - 120V 60Hz / 110V 50 Hz
230 - 240V 60Hz / 220V 50 Hz
265 - 277V 60Hz / 240V 50 Hz
347 VAC / 60 Hz
460 - 480V 60Hz / 440V 50 Hz
575 - 600V 60Hz / 550V 50 Hz
500LG-CCKA1
500LG-CCKA2
500LG-CCKA3
500LG-CCKA4
500LG-CCKA5
500LG-CCKA6
Single Power Pole
Double Power Pole
500LG-1PCK
500LG-2PCK
2 Wire
12 - 24 VDC
24 VAC / 60/50 Hz
110 - 120 VAC / 60/50 Hz
200 - 277 VAC / 60/50 Hz
500LG-47CM12
500LG-47CM24
500LG-47CM120
500LG-47CM277
3 Wire
12 - 24 VDC
24 VAC / 60/50 Hz
110 - 120 VAC / 60/50 Hz
200 - 277 VAC / 60/50 Hz
500LG-48CM12
500LG-48CM24
500LG-48CM120
500LG-48CM277
1 NO / NC
2 NO / NC
500LG-141C
500LG-142C
Power Pole
Control Module Kit
Auxiliary Contact
Wire Temp.
Torque
(lb-in)
#14 - 8
75° C Cu
35
1 or 2
#18 - 14
60° / 75° C Cu
15
1
#22 - 12
60° / 75° C Cu
5
1 or 2
#22 - 12
60° / 75° C Cu
7 - 12
Component
# of Wire
Power Poles
1 or 2
Coil
Control Module
Auxiliary Contacts
Wire Range AWG
(Solid or Stranded)
(5)
PN-20582
DIR 42052-149 (Version 02)
Printed in U.S.A.
">
