Instruction Sheet
1329I Integrated Drive/Motor
CE Filter Option Kit
CE filter options are designed to be used with the 1329I Integrated Drive/Motor.
The main function of the CE filter is to reduce the radio frequency conducted
emissions into the main supply lines and ground wiring. This publication
provides the steps needed to install the filter.
Important:
Declarations of Conformity to the European Union Directives
are available for Allen-Bradley AC drive products. Please
contact your Allen-Bradley Sales Representative.
ATTENTION: The CE filter connects between the incoming AC
supply line and the drive input terminals. The filter must be
installed by qualified personnel familiar with the drive and
associated machinery. Failure to comply may result in personal
injury and/or equipment damage.
ATTENTION: An incorrectly applied or installed CE filter can
result in component damage or a reduction in product life. Wiring
or application errors, such as incorrect wiring layout, incorrect or
inadequate AC supply or excessive ambient temperatures may
result in malfunction of the system.
Refer to the page listed below for installation instructions.
• Internal Mount Option – See page 2.
• NEMA 12 Enclosed Option – See page 5.
2
1329I Integrated Drive/Motor CE Filter Option Kit
Internal Mount Installation
Use the cross-reference table below to verify that the correct filter has been
selected for your CE compatible drive.
Filter Selection
Filter Catalog
Number
Series
Ratings
Use with Bulletin 1329I
Series B Drive/Motor
1329I-NLF1
A
115/230 VAC
Single Phase
14 Amps
1329I-BJ
1329I-BK
1329I-NLF3
A
230/460 VAC
Three Phase
9 Amps
1329I-BL
1329I-BM
Components Supplied
Item
Quantity Supplied
Quantity Required to Install
Screws
M4 × 8 TT
5
4
Lock Washers
M4 Internal Tooth
5
4
1329I Integrated Drive/Motor CE Filter Option Kit
3
Filter Installation
ATTENTION: To prevent electrical shock, disconnect the power
source before installing or servicing.
ATTENTION: After disconnecting input power wait five minutes
and check with voltmeter to assure that DC bus capacitors are
discharged (DC+, DC-). The voltmeter should read zero volts.
Failure to observe these precautions could result in severe bodily
injury or loss of life.
1. Remove the cover of the 1329I unit by loosening the four cover screws.
The display ribbon cable is designed to disconnect from the main unit
when the cover is removed.
2. Mount the CE filter as shown in the figure below using the screws
provided.
1.46 Nm
(13 in-lb)
2.6 Nm
(23 in-lb)
3. The CE filter must be connected between the incoming AC supply line
and the drive input terminals.
Important:
The filter may cause ground leakage currents. Therefore, a solid
ground connection must be provided as shown on the following
page.
4
1329I Integrated Drive/Motor CE Filter Option Kit
ATTENTION: To guard against possible equipment damage, RFI
filters can only be used with AC supplies that are nominally
balanced with respect to ground. In some installations, threephase supplies are occasionally connected in a 3-wire
configuration with one phase grounded (Grounded Delta). The
filter must not be used in Grounded Delta supplies.
Filter Wiring
CE Filter
Conduit/4-Wire Cable
L1
1329I Integrated Drive Motor
W1
IN
OUT
L2
W2
L3
W3
OUT
IN
OUT
IN
R/L1
S/L2
T/L3
PE
Nearest Building Structure Steel
4. Connect wires as shown in the diagram below. (Three Phase unit shown.)
1.3 Nm
(12 in-lb)
L1
L2
L3
PE
DC+
DCDBR
T/L3
S/L2
R/L1
1.3 Nm
(12 in-lb)
1329I Integrated Drive/Motor CE Filter Option Kit
5
5. Reconnect display ribbon cable and reinstall cover.
ATTENTION: The cover screws must be securely tightened in
order to properly ground the cover. Verify that all four cover screws
are tight before applying power to the unit. Failure to observe this
precaution could result in severe bodily injury or loss of life.
NEMA 12 Enclosed
Installation
Use the cross-reference table below to verify that the correct filter has been
selected for your CE compatible drive.
Filter Selection
Filter Catalog
Number
Series
Ratings
Use with Bulletin 1329I
Series B Drive/Motor
1329I-JLF1
A
115/230 VAC
Single Phase
14 Amps
1329I-BJ
1329I-BK
1329I-JLF3
A
230/460 VAC
Three Phase
9 Amps
1329I-BL
1329I-BM
Filter Enclosure Dimensions
29.0
(1.13)
mm
(in)
152.0
(6.0)
292.0
(11.5)
10.0
(0.38)
113.0
(4.46)
273.0
(10.75)
225.0
(8.87)
3.0
(0.10)
6
1329I Integrated Drive/Motor CE Filter Option Kit
Filter Installation
ATTENTION: To prevent electrical shock, disconnect the power
source before installing or servicing.
ATTENTION: The National Codes and standards (NEC, VDE,
BSI, etc.) and local codes outline provisions for safely installing
electrical equipment. Installation must comply with specifications
regarding wire types, conductor sizes, branch circuit protection,
and disconnect devices. Failure to do so may result in personal
injury and/or equipment damage.
1. Mount the NEMA 12 Enclosed CE filter.
The cable length from the filter to the drive/motor must be less than 3
meters (10 feet).
2. The RFI filter must be connected between the incoming AC supply line
and the drive input terminals.
Important:
The filter may cause ground leakage currents. Therefore, a solid
ground connection must be provided as shown on the following
page.
ATTENTION: To guard against possible equipment damage, RFI
filters can only be used with AC supplies that are nominally
balanced with respect to ground. In some installations, threephase supplies are occasionally connected in a 3-wire
configuration with one phase grounded (Grounded Delta). The
filter must not be used in Grounded Delta supplies.
1329I Integrated Drive/Motor CE Filter Option Kit
7
Filter Wiring
CE Filter
1329I Integrated Drive/Motor
L1
Conduit/4-Wire Cable
L1'
IN
OUT
L2
L2'
L3
L3'
PE
PE
OUT
IN
OUT
IN
R/L1
S/L2
T/L3
PE
Nearest Building Structure Steel
3. Connect the wires to the CE filter as shown in the diagram below.
(Three Phase unit shown.)
0.3-0.8 Nm
(3-7 in-lb)
1.3 Nm
(12 in-lb)
2.8 Nm
(25 in-lb)
L1 L2 L3 PE
IN
OUT
Incoming
AC Power
To Integrated Drive/Motor
AC Input Terminals
Bulletin 1329I CE Filter
Option Specifications
1329I-NLF1
1329I-NLF3
1329I-JLF1
1329I-JLF3
Input Voltage
115/230 VAC
230/460 VAC
115/230 VAC
230/460 VAC
Input Phases
Single Phase
Three Phase
Single Phase
Three Phase
Frequency
50/60 Hz
Rated Current
14 Amps
9 Amps
14 Amps
9 Amps
4.72 Kg (10.41 lb)
4.89 Kg (10.78 lb)
Power Dissipation
5 Watts
Leakage Current (Worst Case)
0.5 mA
Weight
0.33 Kg (0.73 lb)
Enclosure
0.45 Kg (0.99 lb)
Internal
NEMA 12/IP 65
Operating Temperature
0° to 40°C (32° to 104°F)
Storage Temperature
-40° to 85°C (-40° to 185°F)
Relative Humidity
5% to 95%, non-condensing
Vibration
1 G operational, 2.5 G non-operational
Shock
15 G operational, 30 G non-operational
Altitude
1000 meters (3300 feet) without derating. For every 91.4 meters (300 feet) above
1000 meters, derate current by 1%. Above 3000 meters (10,000 feet), consult your
Allen-Bradley Sales Office.
International Standards and
Approvals
LIST
ED 966X
UL UL508C
®
IN D
Publication 1329I-5.4 – January, 2000
CONT EQ
LIST
ED 966X
C UL CSA 22.2
®
IN D
CONT EQ
EMC Directive 89/336
LV:
EN 50178, EN 60204
EMC: EN 61800-3, EN 50081-1, EN 50082-2
P/N 194395 (01)
Copyright 2000 Rockwell International Corporation. Printed in USA
">
