Installation Instructions
ArmorBlock LP2 8 Sinking Input/
8 Output Module
(Cat. No. 1792D-8BT8LP)
I-0
O-0
I-1
O-1
I-2
O-2
I-3
O-3
I-4
O-4
I-5
O-5
I-6
O-6
I-7
O-7
Auxiliary Power
Network Status
Module Status
41953
This ArmorBlock LP2™ I/O module (Cat. No. 1792D-8BT8LP) is a
stand-alone 24V dc I/O product which communicates via a DeviceNet™
network. The sealed housing of this module requires no enclosure.
This module has 8 sinking inputs and 8 sourcing outputs accessed through
Y splitter cables. Eight self-protected 24V dc outputs can provide up to
300mA each.
Publication 1792D-5.42 - July 1999
2
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
Package Contents
Your package contains:
•
•
1 ArmorBlock LP2 Module
Installation Instructions
European Communities (EC) Directive Compliance
If this product has the CE mark it is approved for installation within the
European Union and EEA regions. It has been designed and tested to meet
the following directives.
EMC Directive
This product is tested to meet the Council Directive 89/336/EC
Electromagnetic Compatibility (EMC) by applying the following
standards, in whole or in part, documented in a technical construction file:
•
EN 50081-2 EMC — Generic Emission Standard, Part 2 — Industrial
Environment
• EN 50082-2 EMC — Generic Immunity Standard, Part 2 — Industrial
Environment
This product is intended for use in an industrial environment.
Low Voltage Directive
This product is tested to meet Council Directive 73/23/EEC Low Voltage,
by applying the safety requirements of EN 61131-2 Programmable
Controllers, Part 2 - Equipment Requirements and Tests.
For specific information required by EN 61131-2, see the appropriate
sections in this publication, as well as the Allen-Bradley publication
Industrial Automation Wiring and Grounding Guidelines For Noise
Immunity, publication 1770-4.1.
This equipment is classified as open equipment and must be mounted in an
enclosure during operation to provide safety protection.
Publication 1792D-5.42 - July 1999
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
3
Install Your ArmorBlock LP2 I/O Module
To install the module you must:
• Set the node address and baud rate.
• Mount the module.
• Connect the input/output cord sets to the LP2 module.
• Communicate with your ArmorBlock LP2 I/O module.
Each of these steps is discussed in detail in the following procedures.
Set the Node Address and Baud Rate
Set the node address using RSNetWorx for DeviceNet™ software,
DeviceNetManager™ software, or another software configuration tool.
The module is equipped with AutoBaud detect. AutoBaud lets the module
read the settings already in use on your DeviceNet network and
automatically adjusts to follow those settings.
Mount the Module
1. Attach the module using the dimensions shown below.
I-0
O-0
I-1
O-1
I-2
O-2
I-3
O-3
I-4
O-4
I-5
O-5
I-6
O-6
I-7
O-7
4.21 in
107mm
Auxiliary Power
1.95 in
49.5mm
12 in
305mm
Network Status
Module Status
0.25 in
6.25mm
1.02 in
26.0mm
41953
2. Connect the grey DeviceNet cable to the DeviceNet trunk. Use the
1485P-P1R5-MN5R1 T-Port tap to connect to round media. Use the
1485P-P1E4-R5 to connect to the Kwik Link flat media system.
Publication 1792D-5.42 - July 1999
4
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
Connect the Input/Output Cord Sets to the LP2 Module
This module uses 5 pin micro (12mm) style PCB mounted connectors.
Eight micro caps cover the connectors on your module. Remove the caps
and connect your cord sets to the appropriate ports. This product has two
input or outputs per I/O connector. Use a “Y” splitter cable for access to all
I/O connections. For more information on these cables, see the Product
Data guide, publication 1792-2.1.
Use the micro caps to cover and seal unused ports. A pinout diagram for
the connectors is shown below.
Input Micro-Connector
(View into Sockets)
2
1
5
Pin 2 Input B
3
4
Pin 1 Sensor Source Voltage
Pin 3 Return Logic Ground1
Pin 4 Input A
Pin 5 Not Used
Output Micro-Connector
(View into Sockets)
2
1
5
4
Pin 1 Not Used
Pin 2 Output B
3
Pin 3 Auxiliary Power Ground
Pin 4 Output A
41452
Pin 5 Not Used
1.
Logic Ground is approximately 0.4V above DeviceNet V-measured at the module.
Publication 1792D-5.42 - July 1999
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
5
$77(17,21
!
•
•
•
•
Make sure to connect the proper color coded cables
together. DeviceNet cables should connect with
DeviceNet cables and auxiliary outputs should match
auxiliary outputs.
Make sure all connectors and caps are securely tightened
to properly seal the connections against leaks and
maintain IP67 requirements.
For maximum noise immunity, input and output cable
return wires must be properly terminated. When inputs
and outputs are connected in loopback, return wires
should be connected together.
I/O cable length should be less than 30 meters.
I/O connectors for this module are shown below.
Connector A
Connector B
Connector C
Connector D
Input 0
Input 1
Input 2
Input 3
Input 4
Input 5
Input 6
Input 7
I-0
O-0
I-1
O-1
I-2
O-2
I-3
O-3
I-4
O-4
I-5
O-5
I-6
O-6
I-7
O-7
Auxiliary Power
Network Status
Module Status
Output 0 Connector E
Output 1
Output 2
Connector F
Output 3
Output 4
Connector G
Output 5
Output 6 Connector H
Output 7
41943
Publication 1792D-5.42 - July 1999
6
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
Output Power and DeviceNet Cable
Refer to the DeviceNet Cable System Planning and Installation Manual,
publication DN-6.7.2, for more information on output power and
DeviceNet cables for your application.
Communicate with Your ArmorBlock LP2 I/O Module
This ArmorBlock module’s I/O is exchanged with the master through a
polled, change of state, or cyclic connection.
The module consumes and produces I/O data as follows:
Type of I/O Connections
Consumes
Produces
Cyclic
1 Byte
2 Bytes
Polled
1 Byte
2 Bytes
Change of State
1 Byte
2 Bytes
Cyclic - allows configuration of the block as an I/O client. The block will
produce and consume its I/O cyclically at the rate configured.
Polled - a master initiates communication by sending its polled I/O
message to the module. The 8 input/8 output module consumes the
message, updates outputs, and produces a response. The response has input
data and the status of the Auxiliary power.
Change of state - productions occur when an input changes. If no input
change occurs within the expected packet rate, a heartbeat production
occurs. This heartbeat production tells the scanner that the I/O module is
alive and ready to communicate. Consumption occurs when data changes
and the master produces new output data to the I/O module.
Refer to the table below for the word/bit definitions.
Bit
07
06
05
04
03
02
01
Produces 0
I7
I6
I5
I4
I3
I2
I1
I0
Produces 1
ISC
OPWR
RSVD
RSVD
RSVD
RSVD
RSVD
RSVD
Consumes 0
O7
O6
O5
O4
O3
02
01
00
Where: I = Input, ISC = Input Short Circuit, OPWR = Output Power (Auxiliary Power),
RSVD = Reserved, O = Output,
Publication 1792D-5.42 - July 1999
00
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
7
Refer to the table below for byte/bit descriptions.
Byte
Bit
Description
Produces 0
00-07
Input Status bits: When the bit is set (1), the input is on.
Bit 00 corresponds to input 0, bit 01 corresponds to input 1,
bit 02 corresponds to input 2, bit 03 corresponds in input 3.
Produces 1
00-05
06
Reserved
Output Power (OPWR) Fault: When the bit is set (1) auxiliary
power is not present.
Input Short Circuit (ISC).
07
Consumes 0
00-07
Output bits: When the bit is set (1), the output will be turned
on. Bit 00 corresponds to output 0, bit 01 corresponds to
output 1, bit 02 to output 2, bit 03 to output 3, bit 04 to
output 4, bit 05 to output 5, bit 06 to output 6, and bit 07 to
output 7.
The DeviceNet Network uses advanced network technology, producer/
consumer communication, to increase network functionality and
throughput. Visit our web site at http://www.ab.com/networks for producer/
consumer technology information and updates.
Troubleshoot with the Indicators
This module has the following indicators:
•
•
•
•
Network status indicator
Module status indicator
Auxiliary Power indicator
Individual point status indicators for inputs 0 through 7 and outputs 0
through 7
Publication 1792D-5.42 - July 1999
8
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
The following illustration describes module status indicators.
Input Point indicators
and Connectors
Output Point indicators
and Connectors
input 0 and Input 1
Connector A
input 2 and Input 3
I-0
O-0
I-1
O-1
I-2
O-2
I-3
O-3
I-4
O-4
I-5
O-5
Connector B
input 4 and Input 5
Connector C
input 6 and input 7
output 0 and output 1
Connector E
output 2 and output 3
Connector F
output 4 and output 5
Connector G
I-6
O-6
I-7
O-7
Connector D
output 6 and output 7
Connector H
Auxiliary Power
DeviceNet Indicators
Network Status
Module Status
LED Assignments
41944
The following table describes the module status indictor.
Module Status Indicator
Indication
Status
None
No Power
Green
Blinking
Solid
Needs Commissioning
Operating Normal
Red
Blinking
Solid
Recoverable Fault
Unrecoverable Fault
Publication 1792D-5.42 - July 1999
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
9
The following table describes the network status indicator and auxiliary
power.
Network Status Indicator
Indication
Status
None
Not On line
Green
Blinking
Solid
On line/No Connections
On line/Connected
Red
Blink
Solid
Connection Timed Out
Failed Communication: A duplicate
node address exists or module is at the
wrong baud rate.
Auxiliary Power
Indication
Status
None
No Auxiliary Power
Green
Solid
Auxiliary Power Present
The following table describes I/O status indicators.
I/O Status Indicators
Function
Module Status Indicator
Point Indicator Condition
Outputs
Green
Green
None
Yellow
Output not energized
Output energized
Inputs
Green
Green
None
Yellow
No valid input
Valid input
Module Status blink red
None
Short on input connector
For more information on indications, see the Product Data, publication
1792-2.1.
Publication 1792D-5.42 - July 1999
10
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
Specifications
8 Input / 8 Output Module - Cat. No. 1792D-8BT8LP
Sinking Input Specifications
Max
Min
Inputs per block
8- 3 wire or dry contact PNP devices or 4 -4 wire
PNP devices
Sensor Source Current (per input)
50mA
-
On-state Voltage
25V dc
10V dc
On-state Current
10mA
2mA
Off-state Voltage
5V dc
-
Off-state Current
-
1.5mA
Sourcing Output Specifications
Max
Min
Outputs per block
8 sourcing outputs labeled O0, O1, O2, and O3
Output Auxiliary Voltage
30V
10V
On-state Voltage Drop
1V
-
On-state Current
0.3A
-
Off-state Leakage
1.5mA
-
Module Current (all outputs)
2.4A
-
Surge Current - for 10 ms,
repeatable every 2s
0.6A
-
General Specifications
Indicators
Network Status - red/green
Module Status - red/green
Auxiliary Power - green
Point LED - yellow
Communication Rate
•
•
•
DeviceNet Power: Voltage
Current
Publication 1792D-5.42 - July 1999
125Kbps @ 500 meters (1600 feet) for thick
cable, flat media length 375 meters (1230 feet)
250Kbps @ 200 meters (600 feet) for thick
cable, flat media length 150 meters (492 feet)
500Kbps @ 100 meters (330 feet) for thick
cable, flat media length 75 meters (246 feet)
25V dc max
125mA (no sensors)
500mA (full load)
11V dc min
ArmorBlock LP2 8 Sinking Input/ 8 Output Module
11
8 Input / 8 Output Module - Cat. No. 1792D-8BT8LP
General Specifications Continued
Auxiliary Power:
Voltage
Current
30V dc
2.4A max
10V dc
2.4A min
Dimensions (assembled to base)
inches - (millimeters)
1.023H x 2.7W x 6.85D
(26)H x (68.5)W x (174)D
Environmental Conditions
Operational Temperature
Storage Temperature
Relative Humidity
Shock Operating
Non-operating
Vibration
-25 to 60oC (-13 to 140°F)
-25 to 80oC (-13 to 176°F)
Up to 100%
30g peak acceleration, 11 (+1) ms pulse width
50g peak acceleration, 11 (+1) ms pulse width
Tested 10g @ 10-500 Hz per IEC 68-2-6
Conductors
Publication DN-6.7.2
Enclosure
Meets or exceeds IP67
Agency Certification
(when product is marked)
•
Product Data (user information)
Publication 1792-2.1
CE marked for all applicable directives
This product has been tested at an Open DeviceNet Vendor Association,
Inc. (ODVA) authorized independent test laboratory and found to comply
with ODVA Conformance Test Software Composite Test Version 11.
Publication 1792D-5.42 - July 1999
ArmorBlock, ArmorBlock LP2, and DeviceNetManager are trademarks of Rockwell Automation.
DeviceNet is a trademark of Open DeviceNet Vendor Association (ODVA).
RSNetWorx for DeviceNet is a trademark of Rockwell Software, Inc.
Publication 1792D-5.42 - July 1999
PN 955138-11
© (1999) Rockwell International Corporation.Printed in USA
">
