Video Mount Products PDS-LFTB Large Flat Panel Tilt Mount Instruction

Instruction Sheet For:
PDS-LFT & PDS-LFTB
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615
www.videomount.com
ITEM
DESCRIPTION
NO.
1
Wall Plate
2
Tilt Plate
3 Screen Mounting Bracket
4
Metal Spacer
5
Screw M8*P1.25*L75
6
Washer 13* 24*T1.6
7
Washer 8.5* 25*T2.0
8
Nylon Nut M8*P1.25
9
Gear Nut
10
Lever Handle
11
Lever Screw
12
Screw M5*P0.8*L25
13
Screw M4*P0.7*L12
14
Screw M5*P0.8*L12
15
Screw M6*P1.0*L12
16
Screw M8*P1.25*L16.5
17
Screw M4*P0.7*L30
18
Screw M5*P0.8*L30
19
Screw M6*P1.0*L35
20
Screw M8*P1.25*L40
21
Lock Washer M4
22
Lock Washer M5
23
Lock Washer M6
24
Lock Washer M8
25
Washer 5.5* 18*T2
26
Spacer M6
27
Spacer M8
28
Lag Screw 5/16"*2.5"
29 Washer 8.3* 19*T1.6
30
Magnetic Level
QTY.
1
2
2
2
4
4
4
2
2
2
2
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
6
6
1
16
13
17
19
18
15
14
11
21
20
22
12
24
23
28
30
29
25
6
26
27
5
3
PDS-LFT
4
7
10
2
8
9
1
Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Step 2 : Attaching the wall plate
to the wall
Step 3A: Attaching the mounting
rails (holes are not recessed)
Step 2
Mark the wall or desired mounting surface in preparation of installation of wall plate 1 . If mounting to wooden studs, pre drill pi1 the
lot holes using a 7/32” drill bit. Attach the wall plate
to
wooden stud using the 5/16” by 2.5” long lag screw28 and washer
29 making sure the small ear f aps are on the top rail of the wall
plate 1 .
WARNING: Please verify that your mounting surface
will support the combined weight of your mount, mounting hardware, and flat panel. Also verify that the mounting surface is safe
to drill through. Please note only mounting hardware for mounting to wooden studs will be provided with the unit. If mounting to
a surface other than wooden studs then other hardware will be
required. If in doubt or uncertain about any of the above, please
contact a professional installer.
Step 3
Determine the correct screw size and if you need to use washers,
lock washers, or spacers. Note: Spacers are used for TVs with recessed hole patterns. Secure the TV to the screen mount bracket
3 using the appropriate hardware
13through
.27
Note: The
brackets have to be level with each other to work properly..
Step 4
Use the hooks in the wall pivot bracket 2 to hook on the top rail of
the wall plate 1 . Use the M5 screws 12 to secure the f at panel
to the wall plate 1 and to secure its horizontal position.
Step 3B: Attaching the mounting rails (holes are recessed)
Step 5
To adjust tilt, loosen the handles 10 and grasp the top and bottom
of the f at panel and pull the f at panel into position. After achieving
desired tilt retighten the handles. If obstruction prevents full rotation
of the handle pulling out the handle will allow rotation of handle
without affecting the tension of the mount. Push the handle back
down when to wish to adjust the tension further. Use this ratcheting
motion to tighten the tilt mechanism.
Please verify that all nuts and screws
are securely tightened.
Enjoy Your Mount!
Step 4 : Attaching the mounting
rails to the wall plate
WARNING: The installer of these products must verify that the mount
surface, ceiling or wall, will safely support the combined weight of
all attached equipment and hardware. Video Mount Products will
not be held liable for the improper use or installation of its products.