Delta Electronics DNM04S0A0R10 Datasheet
advertisement
Delphi DNM, Non-Isolated Point of Load
DC/DC Power Modules: 2.8-5.5Vin, 0.75-3.63V/10A out
The Delphi Series DNM04, 2.8-5.5V input, single output, non-isolated Point of Load DC/DC converters are the latest offering from a world leader in power system and technology and manufacturing -- Delta Electronics, Inc.
The DNM04 series provides a programmable output voltage from 0.75V to
3.63V using an external resistor. The DNM series has flexible and programmable tracking and sequencing features to enable a variety of startup voltages as well as sequencing and tracking between power modules. This product family is available in a surface mount or SIP package and provides up to 10A of current in an industry standard footprint.
With creative design technology and optimization of component placement, these converters possess outstanding electrical and thermal performance and extremely high reliability under highly stressful operating conditions.
FEATURES
High efficiency: 96% @ 5.0Vin, 3.3V/10A out
Small size and low profile: (SIP)
50.8x 13.4x 8.5 mm (2.00
” x 0.53” x 0.33”)
Signle-in-line (SIP) packaging
Standard footprint
Voltage and resistor-based trim
Pre-bias startup
Output voltage tracking
No minimum load required
Output voltage programmable from
0.75Vdc to 3.63Vdc via external resistor
Fixed frequency operation
Input UVLO, output OTP, OCP
Remote ON/OFF
Remote sense
ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing facility
UL/cUL 60950 (US & Canada) Recognized, and TUV (EN60950) Certified
CE mark meets 73/23/EEC and 93/68/EEC directives
OPTIONS
Negative On/Off logic
Tracking feature
SIP package
APPLICATIONS
Telecom / DataCom
Distributed power architectures
Servers and workstations
LAN / WAN applications
Data processing applications
DATASHEET
DS_DNM04SIP10_07182012D
TECHNICAL SPECIFICATIONS
(T
A
= 25°C, airflow rate = 300 LFM, V in
= 2.8Vdc and 5.5Vdc, nominal Vout unless otherwise noted.)
PARAMETER
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Tracking Voltage
Operating Temperature
Storage Temperature
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Off Converter Input Current
Inrush Transient
Recommended Input Fuse
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Adjustable Range
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Output Current Range
Output Voltage Over-shoot at Start-up
Output DC Current-Limit Inception
Output Short-Circuit Current (Hiccup Mode)
DYNAMIC CHARACTERISTICS
Dynamic Load Response
Positive Step Change in Output Current
Negative Step Change in Output Current
Settling Time to 10% of Peak Deviation
Turn-On Transient
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Output Voltage Rise Time
Maximum Output Startup Capacitive Load
EFFICIENCY
Vo=3.3V
Vo=2.5V
Vo=1.8V
Vo=1.5V
Vo=1.2V
Vo=0.75V
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control, (Negative logic)
Logic Low Voltage
Logic High Voltage
Logic Low Current
Logic High Current
ON/OFF Control, (Positive Logic)
Logic High Voltage
Logic Low Voltage
Logic Low Current
Logic High Current
Tracking Slew Rate Capability
Tracking Delay Time
Tracking Accuracy
Remote Sense Range
GENERAL SPECIFICATIONS
MTBF
Weight
Over-Temperature Shutdown
NOTES and CONDITIONS
Vout ≦ Vin
–0.5
Vin=2.8V to 5.5V, Io=Io,max
Vin=2.8V to 5.5V, Io=Io,min to Io,max
Vin=5V, Io=100% Io, max, Tc=25℃
Vin=2.8V to 5.5V
Io=Io,min to Io,max
Tc=-40℃ to 100℃
Over sample load, line and temperature
5Hz to 20MHz bandwidth
Full Load, 1µF ceramic, 10µF tantalum
Full Load, 1µF ceramic, 10µF tantalum
Vout=3.3V
Io,s/c
10µF Tan & 1µF Ceramic load cap, 2.5A/µs
50% Io, max to 100% Io, max
100% Io, max to 50% Io, max
Io=Io.max
Vin=Vin,min, Vo=10% of Vo,set
Vo=10% of Vo,set
Time for Vo to rise from 10% to 90% of Vo,set
Full load; ESR ≧
1mΩ
Full load; ESR ≧
10mΩ
Vi=5V, 100% Load
Vi=5V, 100% Load
Vi=5V, 100% Load
Vi=5V, 100% Load
Vi=5V, 100% Load
Vi=5V, 100% Load
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
Module On, Von/off
Module Off, Von/off
Module On, Ion/off
Module Off, Ion/off
Delay from Vin.min to application of tracking voltage
Power-up 2V/mS
Power-down 1V/mS
Io=80% of Io, max; Ta=25°C
Refer to Figure 45 for measuring point
DNM04S0A0R10
Typ.
2.2
2.0
70
5
Vo,set
0.3
0.4
0.8
25
8
220
3.5
200
200
25
4
4
4
96.0
94.2
92.4
91.4
90.0
86.3
300
0.2
0.2
100
200
21.91
10
130
Min.
0
-40
-55
2.8
-2.0
0.7525
-3.0
0
-0.2
1.5
-0.2
0.1
10
Max.
5.8
Vin,max
85
125
5.5
10
0.1
15
+2.0
3.63
+3.0
50
15
10
1
8
1000
5000
0.3
Vin,max
10
1
Vin,max
0.3
1
10
2
200
400
0.1 mV mV
µs ms ms ms
µF
% Vo,set
% Vo,set
% Vo,set
% Vo,set mV mV
A
% Vo,set
% Io
Adc
V
V
°C
V
Units
Vdc
Vdc
°C
A mA mA
2
A S
A
% Vo,set
V
V mA
µA
V/msec ms mV mV
V
M hours grams
°C
V
V
% kHz
µF
%
%
%
%
%
µA mA
V
DS_DNM04SIP10_07182012D
2
ELECTRICAL CHARACTERISTICS CURVES
100
100
95
95
90
85
Vin=4.5V
Vin=5.0V
Vin=5.5V
90
85
80
80
75
1 2 3 4 5 6 7
OUTPUR CURRENT(A)
8 9 10
75
1
Vin=3.0V
Vin=5.0V
Vin=5.5V
2 3 4 5 6 7
OUTPUR CURRENT(A)
8 9 10
Figure 1: Converter efficiency vs. output current (3.3V out)
100
95
90
85
80
75
1 2 3 4 5 6 7
OUTPUR CURRENT(A)
Vin=2.8V
Vin=5.0V
Vin=5.5V
8 9 10
Figure 2: Converter efficiency vs. output current (2.5V out)
95
90
85
80
75
70
Vin=2.8V
Vin=5.0V
Vin=5.5V
65
1 2 3 4 5 6 7
OUTPUR CURRENT(A)
8 9 10
Figure 3: Converter efficiency vs. output current (1.8V out)
95
90
85
80
75
70
65
1 2 3 4 5 6 7
OUTPUR CURRENT(A)
8
Vin=2.8V
Vin=5.0V
Vin=5.5V
9 10
Figure 4: Converter efficiency vs. output current (1.5V out)
95
90
85
80
75
70
65
60
1 2 3 4 5 6 7
OUTPUR CURRENT(A)
8
Vin=2.8V
Vin=5.0V
Vin=5.5V
9 10
Figure 5: Converter efficiency vs. output current (1.2V out)
DS_DNM04SIP10_07182012D
Figure 6: Converter efficiency vs. output current (0.75V out)
3
ELECTRICAL CHARACTERISTICS CURVES
Figure 7: Output ripple & noise at 3.3Vin, 2.5V/10A out Figure 8: Output ripple & noise at 3.3Vin, 1.8V/10A out
Figure 9: Output ripple & noise at 5Vin, 3.3V/10A out Figure 10: Output ripple & noise at 5Vin, 1.8V/10A out
Figure 11: Turn on delay time at 3.3Vin, 2.5V/10A out
DS_DNM04SIP10_07182012D
Figure 12: Turn on delay time at 3.3Vin, 1.8V/10A out
4
ELECTRICAL CHARACTERISTICS CURVES
Figure 13: Turn on delay time at 5Vin, 3.3V/10A out Figure 14: Turn on delay time at 5Vin, 1.8V/10A out
Figure 15: Turn on delay time at remote turn on 5Vin, 3.3V/16A out Figure 16: Turn on delay time at remote turn on 3.3Vin, 2.5V/16A out
Figure 17: Turn on delay time at remote turn on with external Figure 18: Turn on delay time at remote turn on with external capacitors (Co= 5000 µF) 5Vin, 3.3V/16A out capacitors (Co= 5000 µF) 3.3Vin, 2.5V/16A out
DS_DNM04SIP10_07182012D
5
ELECTRICAL CHARACTERISTICS CURVES
Figure 19: Typical transient response to step load change at
2.5A/μS from 100% to 50% of Io, max at 5Vin, 3.3Vout
Figure 20: Typical transient response to step load change at
2.5A/μS from 50% to 100% of Io, max at 5Vin, 3.3Vout
(Cout = 1uF ceramic, 10μF tantalum) (Cout =1uF ceramic, 10μF tantalum)
Figure 21: Typical transient response to step load change at
2.5A/μS from 100% to 50% of Io, max at 5Vin, 1.8Vout
Figure 22: Typical transient response to step load change at
2.5A/μS from 50% to 100% of Io, max at 5Vin, 1.8Vout
(Cout =1uF ceramic, 10μF tantalum) (Cout = 1uF ceramic, 10μF tantalum)
DS_DNM04SIP10_07182012D
6
ELECTRICAL CHARACTERISTICS CURVES
Figure 23: Typical transient response to step load change at Figure 24: Typical transient response to step load change at
2.5A/μS from 100% to 50% of Io, max at 3.3Vin, 2.5A/μS from 50% to 100% of Io, max at 3.3Vin,
2.5Vout (Cout =1uF ceramic, 10μF tantalum) 2.5Vout (Cout =1uF ceramic, 10μF tantalum)
Figure 25: Typical transient response to step load change at Figure 26: Typical transient response to step load change at
2.5A/μS from 100% to 50% of Io, max at 3.3Vin, 2.5A/μS from 50% to 100% of Io, max at 3.3Vin,
1.8Vout (Cout =1uF ceramic, 10μF tantalum) 1.8Vout (Cout = 1uF ceramic, 10μF tantalum)
Figure 27: Output short circuit current 5Vin, 0.75Vout
DS_DNM04SIP10_07182012D
Figure 28:Turn on with Prebias 5Vin, 3.3V/0A out, Vbias =1.0Vdc
7
TEST CONFIGURATIONS
L
V
I
(+)
BATTERY
2 100uF
Tantalum
V
I
(-)
Note: Input reflected-ripple current is measured with a simulated source inductance. Current is measured at the input of the module.
Figure 29: Input reflected-ripple test setup
Vo
10uF tantalum
1uF ceramic
SCOPE
Resistive
Load
GND
Note: Use a 10μF tantalum and 1μF capacitor. Scope measurement should be made using a BNC cable.
Figure 30: Peak-peak output noise and startup transient measurement test setup.
V
I
Vo
Vin
GND
Vo
Figure 31: Output voltage and efficiency measurement test setup
Note: All measurements are taken at the module terminals. When the module is not soldered (via socket), place Kelvin connections at module terminals to avoid measurement errors due to contact resistance.
(
Vo
Vi
Io
Ii
)
100 %
DS_DNM04SIP10_07182012D
350
300
250
200
150
100
50
0
0
DESIGN CONSIDERATIONS
Input Source Impedance
To maintain low noise and ripple at the input voltage, it is critical to use low ESR capacitors at the input to the module. Figure 32 shows the input ripple voltage (mVp-p) for various output models using 200 µF(2 x100uF) low
ESR tantalum
capacitor (KEMET p/n: T491D107M016AS,
AVX p/n: TAJD107M106R, or equivalent) in parallel with
47 µF ceramic capacitor (TDK p/n:C5750X7R1C476M or equivalent). Figure 33 shows much lower input voltage ripple when input capacitance is increased to 400 µF (4 x
100 µF) tantalum
capacitors in parallel with 94 µF (2 x 47
µF) ceramic capacitor.
The input capacitance should be able to handle an AC ripple current of at least:
Irms
Iout
Vout
Vin
1
Vout
Vin
Arms
1 2
Output Voltage (Vdc)
3
5.0Vin
3.3Vin
4
Figure 32: Input voltage ripple for various output models, IO =
10 A (CIN = 2
×
100 µF tantalum // 47 µF ceramic)
200
150
100
50
5.0Vin
3.3Vin
0
0 1 2
Output Voltage (Vdc)
3 4
Figure 33: Input voltage ripple for various output models, IO =
10 A (CIN = 4
×
100 µF tantalum // 2
×
47 µF ceramic)
8
DESIGN CONSIDERATIONS (CON.)
The power module should be connected to a low ac-impedance input source. Highly inductive source impedances can affect the stability of the module. An input capacitance must be placed close to the modules input pins to filter ripple current and ensure module stability in the presence of inductive traces that supply the input voltage to the module.
Safety Considerations
For safety-agency approval the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standards.
For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV.
The input to these units is to be provided with a maximum 15A time-delay fuse in the ungrounded lead.
FEATURES DESCRIPTIONS
Remote On/Off
The DNM/DNL series power modules have an On/Off pin for remote On/Off operation. Both positive and negative On/Off logic options are available in the
DNM/DNL series power modules.
For positive logic module, connect an open collector
(NPN) transistor or open drain (N channel) MOSFET between the On/Off pin and the GND pin (see figure 34).
Positive logic On/Off signal turns the module ON during the logic high and turns the module OFF during the logic low. When the positive On/Off function is not used, leave the pin floating or tie to Vin (module will be On).
For negative logic module, the On/Off pin is pulled high with an external pull-up 5k
Ω resistor (see figure 35).
Negative logic On/Off signal turns the module OFF during logic high and turns the module ON during logic low. If the negative On/Off function is not used, leave the pin floating or tie to GND. (module will be On)
Vin Vo
I
ON/OFF
RL
On/Off
GND
Figure 34: Positive remote On/Off implementation
Vin
Rpull-up
I
ON/OFF
On/Off
Vo
RL
DS_DNM04SIP10_07182012D
GND
Figure 35: Negative remote On/Off implementation
Over-Current Protection
To provide protection in an output over load fault condition, the unit is equipped with internal over-current protection. When the over-current protection is triggered, the unit enters hiccup mode.
The units operate normally once the fault condition is removed.
9
FEATURES DESCRIPTIONS (CON.)
Over-Temperature Protection
The over-temperature protection consists of circuitry that provides protection from thermal damage. If the temperature exceeds the over-temperature threshold the module will shut down. The module will try to restart after shutdown. If the over-temperature condition still exists during restart, the module will shut down again. This restart trial will continue until the temperature is within specification
Remote Sense
The DNM/DNL provide Vo remote sensing to achieve proper regulation at the load points and reduce effects of distribution losses on output line. In the event of an open remote sense line, the module shall maintain local sense regulation through an internal resistor. The module shall correct for a total of 0.5V of loss. The remote sense line impedance shall be < 10
.
Distribution Losses
Vin
Vo
Distribution Losses
Vtrim
0 .
7
0 .
1698
Vo
0 .
7525
For example, to program the output voltage of a DNL module to 3.3 Vdc, Vtrim is calculated as follows
Vtrim
0 .
7
0 .
1698
3 .
3
0 .
7525
0 .
267
V
GND
Figure 37: Circuit configuration for programming output voltage
using an external resistor
GND
Vo
TRIM
Vo
TRIM
+
_
Rtrim
Vtrim
RLoad
RLoad
Figure 38: Circuit Configuration for programming output voltage
using external voltage source
Sense
RL
Table 1 provides Rtrim values required for some common output voltages, while Table 2 provides value of external
GND
Distribution
Losses
Distribution voltage source, Vtrim, for the same common output voltages. By using a 1% tolerance trim resistor, set point
operation
electrical specification.
Output Voltage Programming
Table 1
The output voltage of the DNM/DNL can be programmed tolerance of ±2% can be achieved as specified in the to any voltage between 0.75Vdc and 3.63Vdc by
Vo(V) Rtrim(KΩ) connecting one resistor (shown as Rtrim in Figure 37)
0.7525
Open
1.2
41.97
between the TRIM and GND pins of the module. Without this external resistor, the output voltage of the module is
0.7525 Vdc. To calculate the value of the resistor Rtrim for a particular output voltage Vo, please use the following equation:
Rtrim
Vo
21070
0 .
7525
5110
1.5
1.8
2.5
3.3
3.63
23.08
15.00
6.95
3.16
2.21
Table 2
For example, to program the output voltage of the DNL module to 1.8Vdc, Rtrim is calculated as follows:
Rtrim
1 .
8
21070
0 .
7525
5110
15
K
Vo(V)
0.7525
1.2
Vtrim(V)
Open
0.624
1.5
0.573
DNL can also be programmed by apply a voltage between the TRIM and GND pins (Figure 38). The following equation can be used to determine the value of
Vtrim needed for a desired output voltage Vo:
1.8
2.5
3.3
0.522
0.403
0.267
3.63
0.211
DS_DNM04SIP10_07182012D
10
FEATURE DESCRIPTIONS (CON.)
The amount of power delivered by the module is the voltage at the output terminals multiplied by the output
The output voltage tracking feature (Figure 40 to Figure
42) is achieved according to the different external current. When using the trim feature, the output voltage connections. If the tracking feature is not used, the of the module can be increased, which at the same output current would increase the power output of the
TRACK pin of the module can be left unconnected or tied to Vin. module. Care should be taken to ensure that the maximum output power of the module must not exceed the maximum rated power (
Vo.set x
Io.max ≤ P max)
.
For proper voltage tracking, input voltage of the tracking power module must be applied in advance, and the remote on/off pin has to be in turn-on status. (Negative
Voltage Margining
logic: Tied to GND or unconnected. Positive logic: Tied to Vin or unconnected)
Output voltage margining can be implemented in the
DNL modules by connecting a resistor, R margin-up
, from the Trim pin to the ground pin for margining-up the output voltage and by connecting a resistor, R margin-down
,
PS1
PS1
PS2
PS2 from the Trim pin to the output pin for margining-down.
Figure 39 shows the circuit configuration for output voltage margining.
If unused, leave the trim pin unconnected.
A calculation tool is available from the evaluation procedure which computes the values of R margin-up
and R margin-down
for a specific output voltage and margin percentage.
Figure 40: Sequential
Vin
Vo
Rmargin-down
PS1
PS2
PS1
PS2
On/Off
Trim
Q1
Rmargin-up
GND
Rtrim
Q2
Figure 41: Simultaneous
Figure 39: Circuit configuration for output voltage margining
PS1 PS1
Voltage Tracking
The DNM family was designed for applications that have output voltage tracking requirements during power-up and power-down. The devices have a TRACK pin to implement three types of tracking method: sequential start-up, simultaneous and ratio-metric. TRACK simplifies the task of supply voltage tracking in a power system by enabling modules to track each other, or any external voltage, during power-up and power-down.
By connecting multiple modules together, customers can get multiple modules to track their output voltages to the voltage applied on the TRACK pin.
-V△ PS2
Figure 42: Ratio-metric
PS2
DS_DNM04SIP10_07182012D
11
FEATURE DESCRIPTIONS (CON.)
Sequential Start-up
Sequential start-up (Figure 40) is implemented by placing an On/Off control circuit between Vo
PS1
and the On/Off pin of PS2.
PS1
PS2
Vin Vin
Vo
PS1
R3
Vo
PS2
On/Off
R1
Q1
On/Off
R2
C1
Simultaneous
Simultaneous tracking (Figure 41) is implemented by using the TRACK pin. The objective is to minimize the voltage difference between the power supply outputs during power up and down.
The simultaneous tracking can be accomplished by connecting Vo
PS1
to the TRACK pin of PS2. Please note the voltage apply to TRACK pin needs to always higher than the Vo
PS2
set point voltage.
PS1
Vin
Vin
Vo
PS1
TRACK
On/Off On/Off
PS2
Vo
PS2
Ratio-Metric
Ratio
–metric (Figure 42) is implemented by placing the voltage divider on the TRACK pin that comprises R1 and
R2, to create a proportional voltage with Vo
PS1
to the Track pin of PS2.
For Ratio-Metric applications that need the outputs of PS1 and PS2 reach the regulation set point at the same time.
The following equation can be used to calculate the value of R1 and R2.
The suggested value of R2 is 10k
Ω.
V
O
,
PS
2
V
O
,
PS
1
R
1
R
2
R
2
PS1
PS2
Vin
Vin
Vo
PS1
R1
Vo
PS2
TRACK
R2
On/Off
On/Off
The high for positive logic
The low for negative logic
DS_DNM04SIP10_07182012D
12
THERMAL CONSIDERATIONS
Thermal management is an important part of the system design. To ensure proper, reliable operation, sufficient cooling of the power module is needed over the entire temperature range of the module. Convection cooling is usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the thermal performance of the power module is a wind tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in heated vertical wind tunnels that simulate the thermal environments encountered in most electronics equipment. This type of equipment commonly uses vertically mounted circuit cards in cabinet racks in which the power modules are mounted.
The following figure shows the wind tunnel characterization setup. The power module is mounted on a test PWB and is vertically positioned within the wind tunnel. The height of this fan duct is constantly kept at 25.4mm (1
’’).
Thermal Derating
Heat can be removed by increasing airflow over the module. To enhance system reliability, the power module should always be operated below the maximum operating temperature. If the temperature exceeds the maximum module temperature, reliability of the unit may be affected.
FANCING PWB
PWB
MODULE
AIR VELOCITY
AND AMBIENT
TEMPERATURE
SURED BELOW
THE MODULE
AIR FLOW
Note: Wind Tunnel Test Setup Figure Dimensions are in millimeters and (Inches)
Figure 43: Wind tunnel test setup
DS_DNM04SIP10_07182012D
13
THERMAL CURVES
8
6
4
Figure 44: Temperature measurement location
* The allowed maximum hot spot temperature is defined at 125
℃
12
DNM04S0A0R10(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A) @ Vin = 5V, Vo = 3.3V (Either Orientation)
10
Natural
Convection
6
4
2
10
8
2
0
60 65 70 75 80 85
Ambient Temperature (℃)
Figure 45: DNM04S0A0R10 (Standard) Output current vs. ambient temperature and air velocity@Vin=5V, Vo=3.3V(Either
Orientation)
12
DNM04S0A0R10(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin = 5.0V, Vo = 0.75V (Either Orientation)
Natural
Convection
0
60 65 70 75 80 85
Ambient Temperature (℃)
Figure 46: DNM04S0A0R10(Standard) Output current vs. ambient temperature and air velocity@Vin=5V, Vo=0.75V(Either
Orientation)
DS_DNM04SIP10_07182012D
12
DNM04S0A0R10(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A) @ Vin = 3.3V, Vo = 2.5V (Either Orientation)
10
8
6
4
Natural
Convection
8
6
4
2
0
60 65 70 75 80 85
Ambient Temperature (℃)
Figure 47: DNM04S0A0R10 (Standard) Output current vs. ambient temperature and air velocity@Vin=3.3V,
Vo=2.5V(Either Orientation)
12
DNM04S0A0R10(Standard) Output Current vs. Ambient Temperature and Air Velocity
Output Current(A)
@ Vin = 3.3V, Vo = 0.75V (Either Orientation)
10
Natural
Convection
2
0
60 65 70 75 80 85
Ambient Temperature (℃)
Figure 48: DNM04S0A0R10 (Standard) Output current vs. ambient temperature and air velocity@ Vin=3.3V,
Vo=0.75V(Either Orientation)
14
MECHANICAL DRAWING
SMD PACKAGE (OPTIONAL) SIP PACKAGE
DS_DNM04SIP10_07182012D
15
PART NUMBERING SYSTEM
DNM
Product
Series
DNL - 16A
DNM - 10A
DNS - 6A
04 S 0A0 R
Input Voltage
Numbers of
Outputs
04 - 2.8~5.5V
10 - 8.3~14V
S - Single
Output
Voltage
Package
Type
0A0 - R - SIP
Programmable S - SMD
10
Output
Current
10 - 10A
P
On/Off logic
F
N- negative
P- positive
F- RoHS 6/6
(Lead Free)
D
Option Code
D - Standard Function
MODEL LIST
Model Name Packaging Input Voltage
DNM04S0A0R10PFD
DNM04S0A0R10NFD
DNM04S0A0S10PFD
DNM04S0A0S10NFD
SIP
SIP
SMD
SMD
2.8 ~ 5.5Vdc
2.8 ~ 5.5Vdc
2.8 ~ 5.5Vdc
2.8 ~ 5.5Vdc
Output Voltage Output Current
0.75 V~ 3.63Vdc
0.75 V~ 3.63Vdc
0.75 V~ 3.63Vdc
0.75 V~ 3.63Vdc
10A
10A
10A
Efficiency
5.0Vin, 100% load
96.0% (3.3V)
96.0% (3.3V)
96.0% (3.3V)
96.0% (3.3V) 10A
CONTACT: www.deltaww.com/dcdc
USA:
Telephone:
East Coast: 978-656-3993
West Coast: 510-668-5100
Fax: (978) 656 3964
Email: [email protected]
Europe:
Phone: +31-20-655-0967
Fax: +31-20-655-0999
Email: [email protected]
Asia & the rest of world:
Telephone: +886 3 4526107 ext 6220-6224
Fax: +886 3 4513485
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these specifications at any time, without notice
.
DS_DNM04SIP10_07182012D
16
advertisement
Related manuals
advertisement