Product Introduction
Install the print paper
Front View：
01 Open the top cover
Rear View：
USB
Interface
Paper Inlet
Power On
Make sure the top cover is closed in place.
Hold down the power button for 3 seconds to start the printer.
03 Close the top cover
Pull the cover-opening button up，and open the top cover.
Operational
Status LED
Printing Wirelessly from Mobile Phone
01 Power on
02 Adjust Separator
Pull the Separator，Please adjust the separator according to the paper width.
04 Put in the printing paper
Put the Thermal paper face up into the paper inlet, and the paper will enter
the paper automatically.
Connect one side of the USB cable to the PC and the other side to the printer.
Turn on the printer.
Download the printer driver from the website:
https://www.hprt.com/HPRT-MT610
And then install it on the PC.
“HPRT MT610 ”.
出纸口
01
03
quickly). Please use the matching USB cable to charge in time. If you continue
printing, the printer may shut down automatically.
Turn on the Bluetooth on the phone, open the App, click "Connect printer",
and "Connect" with "MT610 -xxxx".
03 Print
charging by power adapter
Open the document you want to print, and copy/share it to App.
（Or select document printing on the App home page）.
Adjust it in the print preview, and click the print icon on the top right corner
to print.
Precautions
The best operating temperature is 0℃~40℃, if the environmental temperature is too low or too high, the print quality may be affected.
Please do not use the unofficial paper roll to ensure the print quality.
During printing, the printer head will heat up,do not touch it to avoid burns.
Note: App operation shall be subject to the latest version.
Please use HPRT official thermal paper for a better printing experience.
02
When the battery is low, the operational status LED will flash (red light flashes
charging by PC
Print side( thermosensitive layer )
Separator
Battery Charging
02 Connect with the printer
Printing from PC
Choose the document you want to print from the PC and print it via printer
出纸口
Scan the QR code below to download App.
To turn off the printer, also hold down the power button for 3 seconds.
Paper Outlet
USB Cable×1
01 Download App
Cover-opening
button
Power Button
Cover-opening
Button
Accessories
Install the print paper
04
05
Do not pull out the paper by force during printing, or else it may damage the
printer.
06
LED Indicator Definitions
1
Error Status
LED Indicator
Status
Voltage/Battery is too low
Red LED flashes rapidly
Out of paper/paper jam/
abnormal paper loading
Red LED flashes slowly
Print head temperature is too high
Red LED flashes rapidly
Red LED is lighting
Printer cover is not closed
2
Printer Status
Status
LED Indicator
fireware is updating
Alternating red, green and blue lights
indicator is flashing
Printing
3
Connection status
Status
In Bluetooth connection
Product Name：Mobile Printer
two conditions: (1) this device may not cause harmful interference, and (2) this device
Product Model：MT610
must accept any interference received, including interference that may cause undesired
Battery Parameter：7.4V, 2000mAh
operation.
Dimensions：266 x 55 x 47mm
Weight：About 0.5kg (without accessories)
Operating Temperature：0℃~40℃
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
White LED flashes slowly
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation.
White LED is lighting
If this equipment does cause harmful interference to radio or television reception, which can
USB data receiving
-- Reorient or relocate the receiving antenna.
Green LED is lighting
No connection currently
Blue LED is lighting
Charging status
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Note: The illustrations of products, accessories, and user interface in the manual
Full charge on boot
may differ slightly from the illustrations, please refer to the actual product.
Display based on connection status
Full charge on shutdown Light off
07
Search“HPRT Official ”on Facebook to Get Extra Consumables of Printer
-- Consult the dealer or an experienced radio/TV technician for help.
Battery charging (on/off) Green LED flashes slowly
Battery charging (printing) White LED flashes slowly
HPRT YouTube Website
the interference by one or more of the following measures:
Green LED flashes rapidly
LED Indicator
Search“HPRT Official ”on YouTube to Get Instruction Videos
protection against harmful interference in a residential installation. This equipment generates,
LED Indicator
In USB connection
Please Scan QR Code to Get 24h After-sales Technical Support Service
This device complies with part 15 of the FCC Rules. Operation is subject to the following
be determined by turning the equipment off and on, the user is encouraged to try to correct
4
E-mail: [email protected]
Web: www.hprtprinter.com
FCC WARNING
Bluetooth data receiving White LED flashes rapidly
Status
Xiamen Hanin Co., Ltd.
Product Parameters
are for reference only. Due to product innovation and upgrade, the actual product
08
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable
exposure condition without restriction.
FCC ID：2AUTE-8DT23J
HPRT Facebook Website
MT610
">
