Karcher FC 7 Cordless Floor Cleaner Instruction manual

FC 7 Cordless
FC 7 Cordless Premium
59698290
(05/23)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
AA
AB
AC
AD
AE
AF
AG
AH
AI
AJ
AK
Contents
Intended use .......................................................
Environmental protection ....................................
Accessories and spare parts...............................
Scope of delivery.................................................
Warranty..............................................................
Safety instructions...............................................
Symbols on the device ........................................
Description of the device.....................................
Installation ...........................................................
Initial startup........................................................
Operation ............................................................
Care and service .................................................
Troubleshooting guide.........................................
Technical data .....................................................
14
14
14
14
15
15
16
16
16
17
17
19
20
22
Intended use
Use the floor cleaner exclusively for cleaning hard floors
in your private household and only on waterproof hard
floors.
Do not clean water-sensitive floor coverings such as
e.g. untreated cork floors, since the moisture can penetrate and damage the floor.
The device is suitable for cleaning PVC, linoleum, tiled,
stone, oiled and waxed parquet, laminate and all waterresistant floor coverings.
Environmental protection
The packing materials can be recycled. Please
dispose of packaging in accordance with the environmental regulations.
Electrical and electronic devices contain valuable, recyclable materials and often components
such as batteries, rechargeable batteries or oil,
which - if handled or disposed of incorrectly - can
pose a potential danger to human health and the environment. However, these components are required for
the correct operation of the device. Devices marked by
this symbol are not allowed to be disposed of together
with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found
at: www.kaercher.de/REACH
Accessories and spare parts
Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.
Scope of delivery
The scope of delivery for the appliance is shown on the
packaging. Check the contents for completeness when
unpacking. If any accessories are missing or in the
event of any shipping damage, please notify your dealer.
14
English
Warranty
Charger
The warranty conditions issued by our sales company
responsible apply in all countries. We shall remedy possible malfunctions on your device within the warranty
period free of cost, provided that a material or manufacturing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
Safety instructions
Read this safety chapter and these original instructions
before using the device for the first time. Act in accordance with them. Keep the original instructions for future
reference or for future owners.
● In addition to the notes in the operating instructions,
you also need to take into consideration the general
safety regulations and accident prevention guidelines applicable by law.
● Warnings and information notices attached to the
device provide important information for hazard-free
operation.
 DANGER ● Never touch the mains plug and
socket with wet hands. ● Do not charge the battery pack
in an explosion-hazard environment.
몇 WARNING ● Protect the power cable from
heat, sharp edges, oil and moving parts. ● Do not cover
the battery pack during the charging process and ensure that the ventilation slits remain clear. ● Do not open
the charger. Repairs are only to be carried out by qualified personnel. ● Only charge the battery pack with the
approved chargers. ● Immediately replace a damaged
charger together with charging cable with an original
part.
몇 CAUTION ● Do not use the battery pack when
dirty or wet. ● Do not carry the charger by the power cable. ● Do not operate the device together with other devices on an extension cable with multiple power
sockets. ● Do not pull the mains plug out the socket using the power supply cable.
ATTENTION ● Only use and store the charger in
dry rooms.
Hazard levels
Battery
 DANGER
 DANGER ● Do not expose the battery to
● Indication of an imminent threat of danger that will
lead to severe injuries or even death.
strong sunlight, heat or fire.
● Indication of a potentially dangerous situation that
may lead to severe injuries or even death.
the original charger enclosed or with a charger approved by KÄRCHER.
Use the following adapter:
몇 WARNING ● Only charge the appliance using
몇 WARNING
몇 CAUTION
PS07
● Indication of a potentially dangerous situation that
may lead to minor injuries.
ATTENTION
WARNING ● Short circuit hazard. Do not open the
battery. Irritating vapours or corrosive liquids can also
escape.
● Indication of a potentially dangerous situation that
may lead to damage to property.
Electrical components
 DANGER ● Do not immerse the device in wa-
ter. ● Never insert conductive objects, e.g. screwdrivers
or similar, into the charging socket on the appliance.
● Never touch contacts or lines. ● Do not damage the
mains connection cable by running it over, crushing it or
pulling it across sharp edges. ● Only connect the device
to alternating current. The voltage indicated on the type
plate must match the voltage of the power source. ● Only operate the device via a fault current protection switch
(maximum 30 mA).
몇 WARNING ● Immediately replace a damaged
charger together with charging cable with an original
part. ● Switch off the device immediately and remove
the mains plug before performing any care and service
work. ● The device contains electrical components. Do
not clean the device or the top or bottom of the floor
head under running water or under a shower spray, otherwise water may enter. ● Only connect the device to an
electrical connection which has been set up by a qualified electrician as per IEC 60364-1.
몇 CAUTION ● Have repair work carried out by
the authorised customer service only. ● Check the device and the accessories each time before operation, in
particular the mains connection and extension cable, to
make sure it is safe and working correctly. Pull out the
mains plug in case of any damage and do not use the
device.
ATTENTION ● This device contains non-replace-
able batteries. Does not apply to appliances with a replaceable
battery pack
Safe handling
 DANGER ● Risk of asphyxiation. Keep pack-
aging film out of the reach of children.
몇 WARNING ● Only use the device for its proper
use. Take into account the local conditions and beware
of third parties, in particular children, when working with
the device. ● Adhere to the respective safety regulations in hazard zones (e.g. service stations). Never operate the device in explosive spaces. ● Children and
persons unfamiliar with these instructions are not allowed to operate the device. The age of the operator
may be limited by local restrictions. ● The device is not
intended for use by children, persons with restricted
physical, sensory or mental abilities or persons unfamiliar with these instructions. ● Persons with reduced
physical, sensory or mental capabilities and persons
lacking experience and knowledge may only use the appliance if they are properly supervised, have been instructed on use of the appliance safely by a person
responsible for their safety, and understand the resultant hazards involved. ● Children must not play with the
appliance. ● Children must be supervised to prevent
them from playing with the appliance. ● Keep the device
out of the reach of children when it is connected to the
English
15
mains or when it is cooling down. ● Children may only
perform cleaning work and user maintenance under supervision. ● Protect the connection cable against heat,
sharp edges, oil and moving unit parts. ● Keep all parts
your body (e.g. fingers, hair) away from the rotating
cleaning rollers ● Risk of injury from sharp objects (e.g.
splinters). Protect your hands while cleaning the floor
head.
몇 CAUTION ● Do not use the appliance if it has
been dropped beforehand, is visibly damaged or if it is
leaking. ● Only operate or store the device in accordance with the description or figure. ● Accidents or damage due to the device falling over. Before all actions with
or on the device, you must make sure that it is stable.
● Never leave the device unsupervised while it is in operation.
ATTENTION ● Device damage. Never fill the water reservoir with solvents, liquids containing solvents or
undiluted acids (e.g. detergents, petrol, paint thinners
and acetone). ● Only switch on the device when the
fresh water tank and waste water tank are installed.
● Do not pick up sharp or larger objects with the device,
such as e.g. glass shards, gravel or toy parts. ● Do not
fill the fresh water container with vinegar, decalcification
agents, essential oils or similar substances. Avoid taking up these substances with the device. ● Use the device only on hard floors with a watertight coating, such
as e.g. varnished parquet, enamelled tiles or linoleum.
● Do not use the device for cleaning carpets or carpeted
floors. ● Do not guide the device over the floor grilles of
convection heating systems. The device cannot vacuum up the escaping water when it is guided over a floor
grille. ● In case of longer breaks in operation and after
use, switch off the device at the main switch / device
switch and pull out the charged mains plug. ● Do not operate the device at temperatures below 0 °C. ● Protect
the device from rain. Do not store the device outdoors.
ON/OFF switch
2
Boost function button
Increased roller speed and additional water quantity
for stubborn dirt
3
Button for adjusting the cleaning level
Switching between cleaning level 1 and 2
4
“Cleaning level 2” indicator
Increased roller speed and water quantity
5
“Cleaning level 1” indicator
Normal roller speed and water quantity
6
"MAX" indicator (red)
The waste water tank is full
7
"MIN" indicator (blue)
The fresh water tank is empty
8
“Battery” indicator (green)
Indicates the charging state of the battery
9
Wall anti-slip handle
10 Handle
11 Fresh water tank
12 Removable hair filters
13 Unlocking button for the waste water tank and park-
ing station
14 Cleaning rollers (4 x)
15 Waste water tank
16 * LED lighting
17 Unlocking button for hair filters
18 Charging socket
19 Parking station
Symbols on the device
●
1
The warning for not cleaning the
floor head under running water is located:
– on the bottom of the floor head.
20 Cleaning station with cleaning brush
21 Charger with charging cable
22 * Cleaning rollers for stone floors (4 x)
23 Detergent RM 536 (30 ml)
24 * Detergent RM 537 (30 ml)
●
●
Symbols for unit cleaning mode after finishing work
are located:
25 * Detergent RM 536 (500 ml)
– engraved in the bowl of the cleaning station,
– as a label on the back of the fresh water tank.
* optional
Symbols for unlocking the waste water tank/parking
station are located:
– as a label on the unlocking button for the waste
water tank/parking station.
The application and description of the symbols (see
chapter Floor head cleaning by means of rinsing process).
Description of the device
The maximum amount of equipment is described in
these operating instructions. Depending on the model
used, there are differences in the scope of delivery (see
packaging).
For the illustrations, refer to the graphics page.
Illustration A
16
26 * Detergent RM 534 (30 ml)
Installation
Installing the handle bar
1. Hold the basic device firmly.
2. Place the cable in the guide of the plastic connector
and fix it.
3. Fit the handle bar all the way to the end stop into the
basic device until it audibly latches into place. The
handle bar must sit tightly in the device.
Illustration B
English
Initial startup
Operation
Charging process
General notes on operation
몇 WARNING
Risk of fire due to defective mains plug
A continuously connected charger can overheat and
cause a fire if the mains plug is defective.
Unplug the charger from the mains after a maximum of
one day.
Note
Unplug the charger from the mains after a maximum of
one day, as a plugged-in charger continuously consumes power.
1. Plug the charging cable of the charger into the
charging socket on the device.
Illustration C
2. Plug the mains plug of the charger into the socket.
The LED indicator lights display the battery's current
charging state.
Illustration D
● All 3 LED indicator lights flash from bottom to top
when charging a completely empty battery.
● The lowermost LED lights up continuously when the
battery is 1/3 charged, the two upper LEDs continue
to flash.
● When the battery is 2/3 charged, the two lower
LEDs light up continuously, the uppermost LED continues to flash.
● The battery is fully charged after 4 hours.
● After the battery has been charged, the 3 LED indicator lights remain on constantly for 60 minutes. After this time, the LED indicator lights go out.
3. Unplug the charger mains plug from the mains socket after charging.
Illustration E
4. Unplug the charging cable from the device.
Fitting the waste water tank
1. Place the device in the middle of the waste water
tank so that it is positioned between the rollers and
then audibly clicks into place. The position of the
tank is not important because it can be inserted in
both longitudinal directions in the device.
Illustration F
The waste water tank must sit tightly in the device.
Filling the fresh water tank
1. Grasp the fresh water tank by the recessed grips at
the side and remove it from the device.
2. Open the tank cap and turn it to the side.
Illustration G
3. Fill the fresh water tank with cold or lukewarm tap
water.
4. Add KÄRCHER detergent or care agent to the fresh
water tank as required.
ATTENTION
Overdosing or underdosing of the detergent or care
agent
Can result in poor cleaning results.
Follow the dosage recommendations for the detergent
or care agent.
5. Close the tank cap.
6. Fit the fresh water tank into the device.
Illustration H
The fresh water tank must sit tightly in the device.
ATTENTION
Moisture
Material damage to sensitive floors
Check the surface to be cleaned for water sensitivity at
an inconspicuous location before using the device.
Do not clean water-sensitive floor coverings such as
e.g. untreated cork floors, since the moisture can penetrate and damage the floor.
ATTENTION
Material damage
Damage to the device from pointed, large and/or bulky
objects.
The device must not be stored and used on hard coarse
dirt and objects, as the parts can get stuck under the
waste water tank and cause scratches on the floor and
tank.
Before starting work and storing the device, remove objects such as shards, pebbles, screws or toy parts from
the floor.
Illustration AI
Note
● To avoid striped patterns, test the device on an inconspicuous area before using on sensitive surfaces, e.g. wood or fine stone.
● Do not allow it to remain in one area, but keep it in
motion.
● Observe the instructions for the floor covering manufacturer.
Note
Work backwards towards the door so that no footprints
are generated on the freshly washed floor.
Illustration AJ
● Floor cleaning is performed using a to and fro movement at the same speed as when vacuuming.
● Activate the Boost function for heavy soiling. Hold
the Boost function button pressed for this. The roller
speed and water volume are increased when the
boost function is activated. The Boost function can
be activated at cleaning level 1 and cleaning level 2.
The indicator for the corresponding cleaning level
flashes when the Boost function is activated. Allow
the device to slide slowly over the floor without exerting any pressure on the device.
Illustration K
● Various different rollers are available, depending on
the scope of delivery. The colour of the rollers indicates the respective special application for which
they are suitable.
– Grey / yellow universal rollers: versatile
– Rollers with black stripes: For cleaning insensitive hard floors (e.g. stone, ceramic); not suitable
for sensitive natural stone floors (e.g. marble, terracotta)
Note
For an optimum cleaning result, wash the rollers in the
washing machine at 60° C before initial use.
ATTENTION
Material damage due to loose rollers
This may damage the washing machine.
Place the rollers in a laundry net and load the washing
machine with extra laundry.
English
17
Starting work
●
ATTENTION
Uncontrolled motion
Damage to the device and material damage
The cleaning rollers start rotating as soon as the device
is switched on.
Hold the handle tight to prevent the device from moving
away independently.
ATTENTION
Fresh water tank or waste water tank not installed
Material damage
Before starting cleaning work, ensure that the fresh water tank is filled with water and the waste water tank is
fitted in the device.
1. Press the ON/OFF switch.
Illustration I
The device switches on.
The cleaning level 1 indicator for normal roller
speed and normal water quantity is lit.
2. Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
Note
If the rollers block immediately after switching on, remove the rollers, moisten them under the tap and reinsert them.
3. If necessary, switch to cleaning level 2 using the button for adjusting the cleaning level.
Illustration J
This increases the roller speed and water volume.
The Cleaning level 2 indicator lights up.
Note
Selection of cleaning level 1 or cleaning level 2 depends on the type of floor to be cleaned (e.g. wooden or
stone floor).
The device is set to cleaning level 1 after initial start-up.
The cleaning level setting last used always remains activated after interrupting and resuming work.
4. If necessary, activate the boost function for cleaning
stubborn dirt (see also chapter General notes on
operation).
Illustration K
Battery run time
The "Battery" indicator shows the remaining battery run
time:
● 3 LEDs illuminated - 3/3 (full) battery run time
● 2 LEDs illuminated - 2/3 battery run time
● 1 LED illuminated - 1/3 battery run time
Illustration N
Acoustic or optical signals warn of a flat battery.
● An acoustic signal sounds 2 times and the lowest
LED flashes approx. 5 minutes before the battery is
empty.
● An acoustic signal sounds 2 times and the lowest
LED continues to flash approx. 1.5 minutes before
the battery is empty.
● The last LED flashes quicker for 60 seconds when
the battery is empty and the device has switched off.
●
1.
2.
3.
4.
5.
Refilling with detergent
●
The "MIN" indicator (blue) lights up and an acoustic
signal sounds when the fresh water tank is empty.
Illustration L
● The acoustic signal sounds once a minute as a reminder.
1. Fill the fresh water tank (see Chapter Filling the
fresh water tank).
Interrupting operation
ATTENTION
Damp rollers
Moisture damage to sensitive floors
To prevent damage to sensitive floors through wet rollers, place the device in the parking station during longer
work breaks.
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Note
If the device is placed on the parking station without a
waste water tank, the unlocking button must be pressed
to remove the device.
Illustration AG
Ending operation
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Illustration AC
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
3. Clean the device (see Chapter Care and service).
Emptying the waste water tank
●
●
18
The "MAX" indicator (red) lights up and an acoustic
signal sounds when the waste water tank is full.
Illustration M
After 60 seconds, an acoustic signal sounds again
and the device switches off.
The "MAX" indicator (red) flashes for 10 seconds
once the device is switched off.
As long as the waste water tank is full and the (red)
“MAX” display lights up, the process restarts and the
following two steps are repeated:
a The device can be switched on again.
b The device runs for another 60 seconds and then
switches off again.
Press the ON/OFF switch.
The device switches off.
Press the unlocking button for the waste water tank
with your foot and lift the device.
Illustration O
The waste water tank releases from the device.
For draining, do not transport the waste water tank
by the top cover, but horizontally with both hands at
the narrow sides.
Empty the waste water tank through the opening in
the cap. In the case of adhering dirt deposits, remove the cover of the waste water tank and rinse
the waste water tank with tap water.
Fit the waste water tank (see Chapter Fitting the
waste water tank).
Storing the device
ATTENTION
Liquids/moist dirt
Unpleasant odours can develop if the device contains
liquids/moist dirt when stored.
English
Completely empty the fresh water tank and waste water
tank before storing the device.
Use the cleaning brush to remove hair and dirt particles
from the hair filters in the floor head cover.
Allow the cleaned rollers to dry in the air, e.g. mounted
in the device on the parking station. Do not place the wet
rollers in an enclosed cupboard to dry.
1. Put the empty waste water tank in the cleaning station to dry.
a Place the device on the parking station and let it
snap into place.
b Then place the device with the parking station on
the cleaning station.
Illustration AC
2. Fit the cleaned rollers on the device for drying.
Illustration AD
3. Charge the battery (see Chapter Charging process).
4. Store the device in a dry room.
Illustration AF
Care and service
Floor head cleaning by means of rinsing
process
ATTENTION
Dirt or detergent residues
The waste water tank and the hair filters must be
cleaned regularly to ensure that dirt does not accumulate in the tank and hair filters. Dirt particles can clog the
hair filters and slots if the device is not cleaned after use.
The accumulation of dirt and bacteria can also result in
the development of unpleasant odours in the device.
On completion of work, place the device in the cleaning
station and start the rinsing process.
Clean the floor head in the cleaning station only by using the automatic rinsing process and not by pouring
water into the station separately. Make sure that the
waste water tank is attached.
Do not clean the device or the top or bottom of the floor
head under running water or under a shower spray, otherwise water may enter.
Note
The rinsing process cannot be started while the "MAX"
indicator (red) is lit and the waste water tank has not
been emptied.
Note
The LED lighting on the floor head remains switched off
during the rinsing process.
1. Press the ON/OFF switch.
The device switches off.
2. Empty the waste water tank and reinsert it (see
chapter Emptying the waste water tank).
3. Place the device with an empty waste water tank in
the parking station.
4. Fill the fresh water tank with at least 200 ml of fresh
water without a detergent or care agent (see chapter
Filling the fresh water tank).
Illustration P
Note
It is not necessary to add detergent for the rinsing process.
5. Hold the ON/OFF switch and the cleaning level adjustment button simultaneously pressed for
3 seconds.
An acoustic signal sounds.
Illustration Q
6. The indicators light up repeatedly from top to bottom.
The rinsing process starts and takes approx. 2 minutes.
Illustration R
Note
At the start of the rinsing process, the water runs from
the fresh water tank onto the rollers for approx. 80 seconds. During this time the device is silent. Only at the
end of the rinsing process do the rollers start to turn for
approx. 30 seconds.
7. When the rinsing process is finished, a signal tone
sounds and the (red) “MAX” display lights up.
Illustration S
8. Press the unlocking button for the waste water tank
and place the device on the parking station. The
waste water tank remains in the cleaning station.
Note
The (red) "MAX" display flashes for 10 seconds if an attempt is made to switch the device on again with a full
waste water tank.
Cleaning work cannot be continued.
9. Press the unlocking button for the hair filters inwards.
The hair filters are released.
10. Place the hair filters in the cleaning station.
Illustration U
11. Remove the rollers and place them in the cleaning
station.
Illustration V
12. Transport the cleaning station with waste water
tank, hair filters and rollers to the toilet, sink or waste
container as required.
Illustration W
13. Clean the waste water tank (see chapter Cleaning
the waste water tank).
14. Clean the rollers (see chapter Cleaning the rollers).
15. Clean the hair filters (see chapter Cleaning the hair
filters).
16. Clean the underside of the floor head and the roller
drive with a moist cloth.
Illustration AB
Note
Do not clean the device or the top or bottom of the floor
head under running water or under a shower spray, otherwise water may enter.
17. Empty and dry the cleaning station.
18. If water is still present in the fresh water tank, remove and drain the fresh water tank.
Cleaning the waste water tank
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
Clean the waste water tank regularly.
For information on the waste water tank indicator and
the procedure for cleaning the waste water tank, see
Chapter Emptying the waste water tank.
1. Remove the waste water tank cap.
Illustration X
2. Clean the waste water tank and cap with tap water.
3. Alternatively, the waste water tank can be cleaned in
a dishwasher.
Note
The rubber inlays of the waste water tank flap can become sticky when cleaned in a dishwasher. This does
not affect their sealing ability.
English
19
Cleaning the rollers
ATTENTION
Detergent residue in the rollers
Foaming
Wash the rollers under running water or clean them in a
washing machine each time after using the device.
ATTENTION
Damage due cleaning the rollers with fabric softener or using a clothes dryer
Damage to the microfibres
Do not use fabric softener when cleaning in a washing
machine.
Do not dry the rollers in a clothes dryer.
ATTENTION
Material damage due to loose rollers
This may damage the washing machine.
Place the rollers in a laundry net and load the washing
machine with extra laundry.
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Illustration AC
3. Unscrew the cleaning rollers via the recessed grip.
Illustration V
4. Clean the cleaning rollers under running water on in
a washing machine at max. 60 °C.
Illustration Y
5. Twist the cleaning rollers as far as they will go onto
the roller holder. Pay attention to the colour coding
on the inner side of the roller and on the roller holder
(e.g. blue to blue).
Illustration AD
6. Allow the rollers to dry on the device and on the
parking station.
Illustration AF
Cleaning the hair filters
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
It is recommended to clean the device completely after
each application.
ATTENTION
Adhering dirt deposits
Adhering dirt deposits can damage the device in the
long term.
Clean both hair filters regularly with the cleaning brush.
ATTENTION
Damage due to cleaning the hair filters in a dishwasher
The washing process can distort the scraper edge and
it will no longer press on the rollers correctly. This worsens the cleaning result.
Do not clean the hair filters in a dishwasher but rather
under running water.
1. Press the ON/OFF switch.
The device switches off.
2. Place the device in the parking station.
Illustration AC
3. Press the unlocking button for the hair filters inwards.
Illustration U
The hair filters are released and can be removed.
4. Clean both hair filters under running water.
20
5. Remove adhering dirt deposits, e.g. in the filter
comb, using the cleaning brush.
Illustration AA
Illustration Z
6. Insert the hair filters into the floor head and allow
them to latch into place. Both hair filters must sit
tightly in the device.
Illustration AE
Cleaning and care agents
ATTENTION
Use of unsuitable detergents and care agents
The use of unsuitable detergents and care agents can
damage the device and loss of eligibility for warranty
claims.
Use only KÄRCHER detergents.
Take care to ensure the correct dosage.
Note
Use KÄRCHER detergent or care agents for floor cleaning as necessary.
 Observe the manufacturer's dosing quantity recommendations when dosing with detergent or care
agents.
 To prevent foaming, fill the fresh water tank with water first and the add the detergent or care agent.
 To prevent the tank from overflowing, be sure to
leave enough space for the detergent or care agent
when filling with water.
Troubleshooting guide
Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
Note
The device is disabled for 3 seconds when a fault occurs.
The device cannot be switched on again until the fault
has been corrected.
The battery is not charging
The charging plug/mains plug is not connected correctly.
 Connect the charging plug/mains plug correctly.
The error LED ("Battery" indicator) flashes when
the device is switched on and the device does not
start
The battery is discharged.
 Charge the battery (see Chapter Charging process).
An incorrect or faulty charger was used.
 Use the original charger.
 Replace the faulty charger.
The device switches off and the LED fault display
("Battery" display) flashes.
The device overheats (e.g. at high ambient temperatures, when used with dry rollers or when used on carpet).
 Allow the device to cool down for approx. 2.5 hours.
The device can only be switched on again once it
has cooled down enough. The device may be
charged while it is cooling down.
The cleaning level 1 and cleaning level 2 indicators
flash simultaneously and the rollers do not rotate
The device has a motor blockage, e.g. due to excessive
pressure on the rollers or through movement into a wall/
corner.
 Switch the device off and back on again.
The rollers are blocked.
English
 Remove the rollers and check if an object has become stuck in the rollers.
 Check that the rollers are screwed in as far as they
will go onto the roller holder.
 Check if dirt has accumulated in the hair filters in the
floor head and remove any dirt present.
 Check that the hair filters are fitted correctly. For
this, remove the hair filters and then fit then back in
place.
The hair filters are blocking the rollers. The rollers are
not being sufficiently moistened.
 Press the ON/OFF switch.
The device switches off.
 Press the unlocking button for the hair filters inwards
and remove the hair filters.
 Press the ON/OFF switch.
The device switches on.
 Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
Note
If the rollers are not sufficiently moistened, remove the
rollers, moisten them under the tap and reinsert them.
 Fit the hair filters.
The display lights up repeatedly from top to bottom
The device is in the 2-minute rinsing process for cleaning the floor head
 Wait for about 2 minutes, then rinsing is finished and
the display no longer lights up (see Chapter Floor
head cleaning by means of rinsing process).
The display indicator "Fill fresh water tank" lights
up although the fresh water tank is filled.
The sensor of the fresh water tank holder is dirty.
 Remove the fresh water tank and clean the sensor
of the fresh water tank holder, e.g. with a cotton
swab.
Illustration AH
The water in the tank is too soft.
 Do not use distilled water for cleaning.
The device cannot be switched on
The battery is discharged.
 Charge the battery.
The charging cable is still plugged into the device.
 Unplug the charging cable, operation is not possible
while the charging cable is plugged in.
The device rattles loudly when switched on
The rollers are not being sufficiently moistened.
 Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
Note
If the rollers are not sufficiently moistened, remove the
rollers, moisten them under the tap and reinsert them.
The rollers have deformed.
 Only store the device on the parking station and not
on the floor, as the rollers may deform due to the
contact pressure.
The device does not absorb dirt
There is no water in the fresh water tank. The "MIN"
(blue) indicator lights up and an acoustic signal sounds.
 Refill the fresh water tank with water.
The fresh water tank is not sitting properly in the device.
 Insert the fresh water tank so that it is firmly seated
in the device.
The waste water tank is missing or not sitting properly in
the device.
 Insert the waste water tank in the device so that it
audibly latches into place.
 Check whether the lid of the waste water tank is correctly fitted (filler tab must be placed in the recess
provided).
The hair filters are missing or are not sitting correctly in
the device.
 Fit the hair filters correctly in the device.
The rollers are missing or not sitting properly in the device.
 Fit the rollers or twist the rollers as far as they will go
onto the roller holder.
The rollers are dirty or worn out.
 Clean the rollers or replace if necessary.
The rollers are too dry
The rollers are not being sufficiently moistened.
 Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
Note
If the rollers are not sufficiently moistened, remove the
rollers, moisten them under the tap and reinsert them.
The fresh water filter is dirty.
 Clean the fresh water filter.
a Remove the fresh water tank and take out the
fresh water filter.
Illustration AH
b Clean the fresh water filter under running water.
c Reinsert the fresh water filter.
Poor cleaning result
Rollers were not washed before initial use.
 Wash the rollers in a washing machine at 60°C.
The rollers are dirty.
 Clean the rollers.
The rollers are not being sufficiently moistened.
 Moisten the rollers.
a Hold the Boost function button pressed.
b Move the device back and forth until the rollers
are sufficiently moistened.
Incorrect detergent or incorrect dosage.
 Use only KÄRCHER detergent and be sure to use
the correct dosage.
Foreign detergents are present on the floor.
 Thoroughly remove all detergent residues from the
rollers using water.
 Clean the floor several times using the device and
clean rollers, without using detergent.
This removes all detergent residues from the floor.
The water absorption is not optimal
The hair filters are not sitting correctly in the device.
 Fit the hair filters correctly in the device.
The rollers are worn out.
 Replace the rollers.
The device is losing waste water
The waste water tank is full.
 Empty the waste water tank immediately.
The waste water tank is not sitting properly in the device.
 Insert the waste water tank in the device so that it
audibly latches into place. The waste water tank
must sit tightly in the device.
The hair filters are not sitting correctly in the device.
 Check that the hair filters are fitted correctly.
The waste water tank is damaged.
 Contact the authorised Customer Service.
English
21
The device switches on
As soon as the waste water tank has exceeded a volume of 200 ml, automatic device shutdown is activated.
If detergents from other manufacturers are used, excessive foaming can occur and the device shutdown is activated before the 200 ml level is reached.
 Empty the waste water tank.
 Use only KÄRCHER detergent and be sure to use
the correct dosage.
The device engages in joints when used
The knobs on the underside of the waste water tank are
damaged or worn.
 Contact the authorised Customer Service.
Removing the handle
Frequent removal of the handle
The handle components can be damaged by repeated
removal.
Do not remove the handle from the basic device after
assembly.
The handle may only be removed from the basic device
when the device is sent out for service purposes.
ATTENTION
Incorrect removal of the handle
Device damage
Take care to ensure that the connection cable between
the basic unit and the handle is not damaged.
 Insert a screwdriver at a 90° angle in the small opening at the rear side of the handle and remove the
handle.
Illustration AK
Technical data
FC 7
Electrical connection
Voltage
V
Phase
~
1
Frequency
Hz
50 - 60
100 240
IPX4
Device protection class
III
Charger protection class
II
Nominal power of device
W
80
Nominal voltage of battery
V
25.20 25.55
Battery type
Li-Ion
Operating time when battery is ful- min
ly charged
45
Charging time for an empty battery
h
4
Output voltage of charger
V
30
Output current of charger
A
0.6
Roller rotations per minute at
cleaning level 1
rpm
450
Roller rotations per minute at
cleaning level 2
rpm
490
Roller rotations per minute with
Boost function
rpm
530
Device performance data
22
Fresh water tank capacity
ml
400
Waste water tank capacity
ml
200
Weight (without accessories and
cleaning fluids)
kg
4.3
Length
mm
310
Width
mm
230
Height
mm
1210
Dimensions and weights
Subject to technical modifications.
ATTENTION
Degree of protection
FC 7
Filling quantity
THANK YOU!
MERCI! DANKE! ¡GRACIAS!
Registrieren Sie Ihr Produkt und profitieren Sie von vielen Vorteilen.
Register your product and benefit from many advantages.
Enregistrez votre produit et bénéficier de nombreux avantages.
Registre su producto y aproveche de muchas ventajas.
www.kaercher.com/welcome
Bewerten Sie Ihr Produkt und sagen Sie uns Ihre Meinung.
Rate your product and tell us your opinion.
Évaluer votre produit et dites-nous votre opinion.
Reseñe su producto y díganos su opinión.
www.kaercher.com/dealersearch
Alfred Kärcher SE & Co. KG
Alfred-Kärcher-Str. 28-40
71364 Winnenden (Germany)
">