Roller shutter drive RolTop/D+ M
Table Of Contents
Roller shutter drive RolTop/D+ M
1
Operating and installation instructions
(translation)
1
2
General for instructions
1
2.1
Standards and Directives
1
Please keep these operating instructions for later use, to be
available throughout the life of the product!
2.2
Intended use
1
The German manual is the original version.
2.3
Foreseeable misuse
2
All other documents represent the language translations of
the original text.
2.4
Warranty and liability
2
2.5
Customer service of the manufacturer
2
All rights in the case of a patent, utility model or ornamental
design registration are reserved.
3
Safety
2
3.1
General safety instructions
2
3.2
Layout of the safety guidelines
2
3.3
Safety principles
3
3.4
General operational regulations
3
3.5
Requirements for the personnel
3
3.6
Safety instructions for technical condition
3
3.7
Safety instructions for transport,
assembly, installation
3
3.8
Safety instructions for operation
4
3.9
Safety instructions for electrical installation
4
4
Product description
4
5
Assembly
4
5.1
Mechanical fastening
5
5.2
Electrical connection
5
5.3
Connection example RolTop/D+ M 230V / 50Hz 6
5.4
Parallel connection
6
5.5
Commissioning
6
1
2
Operating and installation
instructions (translation)
General for instructions
The content structure is based on the life cycles of the electric motor drive (hereinafter referred to as "Product").
The manufacturer reserves the right to make changes to the
Specifications stated in these Operating Instructions at any
time. These may, in individual cases, be different from the
respective product version, however the functional information will not undergo significant changes or become invalid.
The current version of the Specifications may be requested
from the manufacturer at any time. No claims may be asserted against the manufacturer as a result of the preceding sentence. Deviations from text or picture statements
are possible and depend on the technical development,
features, and accessories of the products. Deviating information on special versions will be explained by the manufacturer in the sales documentation. Other information shall
remain unaffected by these provisions.
2.1
Standards and Directives
During the design process, the basic health and safety
requirements of the applicable laws, Standards and Directives were complied with. The safety is confirmed by the
declaration of conformity (see "Declaration of Conformity").
All safety information in these Operating Instructions refer
to the laws and regulations currently applicable in Germany.
All instructions in the Operating Instructions shall be observed without limitation and at any time. Beside the safety
instructions contained in these Operating Instructions, the
provisions for accident prevention, environmental protection and occupational safety, which are applicable for the
operating site, must be observed. Provisions and Standards
for the safety rating can be found in the EC Declaration of
Conformity
5.5.1 Automatic programming of end limits
6
5.5.2 Manual setting of the end positions
6
5.5.3 Changing / Deleting the limit positions and
deleting the discharge function
6
5.6
Specifications
6
6
Troubleshooting
7
7
Repair
7
8
Repair
7
9
Address
7
The operator will be solely responsible for damages resulting from improper use of the product. The manufacturer
cannot be held liable for personal or material damages
caused by misuse or procedural errors, and by improper
operation and commissioning.
10
Disposal / scrapping
7
The product may be operated only by trained and authorized personnel under observance of all safety.
11
EC Declaration of Conformity
7
12
Technical data and dimensions
7
2.2
Intended use
The product is intended for use in façade engineering to
drive electrically powered sun protection devices.
The determining factor for the drive is the elero drive computation program
www.elero.com/en/downloads-service .
Further fields of application have to be arranged with the
manufacturer, elero GmbH Antriebstechnik (see Address).
13 817.2101_EN_0224
Intended Use | Safety
Only if used according to the specifications of these operating and installation instructions for the safe and proper use
and safe operation of the product are guaranteed.
Symbol
Intended use includes the observance and compliance with
all safety instructions with regards to this operating manual
and all applicable regulations, and professional associations
of applicable laws for environmental protection. Intended
use includes the observance of prescribed operating rules
in these operating and installation instructions.
2.3
Foreseeable misuse
Signal
word
Meaning
DANGER
Warns before an accident,
which will result if instructions are not followed,
which can lead to lifethreatening, irreversible
injury or death.
WARNING
Warns before an accident,
which can happen if the
instructions are not followed, which can lead to
serious, possibly fatal,
irreversible injury or death.
CAUTION
Warns before an accident,
which can happen if the
instructions are not followed, which may lead to
minor reversible injury.
A use which deviates from the intended use stated by the
manufacturer, elero GmbH Antriebstechnik (see "Address"),
is deemed as foreseeable misuse.
2.4
Warranty and liability
Principally, the General Terms and Conditions of the manufacturer, elero GmbH Antriebstechnik (see "Address"),
apply. The terms and conditions are part of the sales
documents and handed over to the operator upon delivery. Liability claims for personal or material damages are
excluded when they can be attributed to one or more of the
following causes:
• Opening of the product by the customer
• Unintended use of the product
• Improper installation, commissioning, or operation of the
product
• Structural modifications to the product without the written
consent of the manufacturer
Fig. 1 Notation of personal injury
The following table describes the icons used in these operating instructions that are used for imaging of the dangerous situation in connection with the symbol of the threat
level.
Symbol
Danger of electric voltage, electric
shock:
This symbol indicates a risk of electric
shock.
• Operation of the product with improperly installed connections, defective safety devices or improperly installed
safeguards
• Non-observance of the safety provisions and instructions
of these Operating Instructions
• Non-compliance with the technical data
2.5
Customer service of the manufacturer
The product should only be repaired by the manufacturer
in case of a failure. The address for sending to customer
service, see the chapter "Address".
If you have not purchased the product directly from elero,
please contact the supplier of the product.
3
Safety
3.1
General safety instructions
Fig. 2 Notation-specific hazard
The following table defines the representation used in the
operating instructions and description of situations where
damage can occur to the product or refers to important
facts, conditions, tips and information.
Symbol Signal
word
These operating and installation instructions contain all the
safety instructions that must be observed in order prevent
and eliminate hazards in the handling of the product in the
individual life cycles. The safe operation of the product
can only be ensured when all given safety instructions are
observed.
3.2
Meaning
NOTE
This symbol warns of a
possible property damage.
Important:
This symbol points out
important facts and conditions as well as to additional information in these
operating and installation
instructions. It also refers
to certain statements that
give additional information
or help you perform a task
easily.
Layout of the safety guidelines
The safety instructions in this document are identified by
hazard signs and safety symbols and are designed according to the SAFE principle. They contain information on the
nature and source of the danger of possible consequences
and to prevent the danger.
The following table defines the representation and description of hazard levels with possible personal injury, as used
in this manual.
Fig. 3
Meaning
Notation of property damage as well as additional
information
The following example represents the basic structure of a
safety warning:
SIGNAL WORD
Type and source of danger
Explanation of the type and source of the danger
►Measures to prevent the danger.
2 | EN
© elero GmbH
Safety
3.3
Safety principles
Before starting any activities, the staff must be made
familiar with the dangers when handling the product.
The product is designed according to state of the art and
recognized safety standards and is safe to operate. During the design process of the product, the basic health and
safety requirements of the applicable laws, Standards and
Directives were complied with. The safety of the product is
confirmed by the EC declaration of conformity.
Any personnel who have been assigned to work with the
product must not have a physical disability, the attention
and judgement must not be temporarily or permanently
restricted (e.g due to fatigue).
The handling of the product and all assembly, disassembly and cleaning work by minors or persons who are
impaired by alcohol, drugs or medication influence, is not
permitted.
Any information relating to safety are based on the currently
valid regulations of the European Union. In other countries,
it must be ensured by the operator that the applicable laws
and state regulations are complied with.
Staff must accordingly wear the necessary work and this
work environment suitable personal protective equipment.
In addition to the safety instructions in this operating
manual, the general regulations for accident prevention and
environmental protection must be observed and adhered to.
The product is to be used only in technically flawless state
as well as in accordance with the requirements, conscious
of risk and in compliance with the operating instructions.
The product is designed for use as described in chapter
"Intended Use". In case of improper use, threats to life and
limb of the user or third parties or damage to the product or
other property may occur. Accidents or near accidents when
using the product, resulting in personal injury and / or damage to the environment or has happened, shall be reported
to the manufacturers directly and immediately.
Do not allow children to play with stationary controls,
keep remote controls away from children.
Watch the moving shutter and keep people until the shutter is fully closed.
3.6
The product should be checked for damage and proper
condition before installation.
The operator is required to operate the product in a
proper and safe condition. The technical condition must
satisfy legal requirements that were valid for mentioned
on the nameplate production date.
All safety precautions listed in the operating instructions
and on the product are to be observed. In addition to these
safety instructions, the operator shall ensure that all national and international regulations in force in the country of
use, as well as other binding regulations for occupational
safety, accident prevention and environmental protection
are met. All works on the product must be carried out by
trained, safety related trained and authorized personnel.
The professionally qualified person must comply with all
applicable standards and laws in the country of installation
and inform their customers about the use and maintenance
conditions of the product.
3.4
General operational regulations
If danger to persons or changes are recognized in operating performance, the product must be immediately taken
out of service and the incident is reported to the operator.
No changes to the product, additions or modifications
should be performed without prior approval of the manufacturer.
The plant is (if applicable) to be checked often for defective balance or any signs of wear or damaged cables and
springs.
3.7
The operator is obliged to use the product only in proper
and safe condition. He must ensure that in addition to the
safety instructions in the operating manual, the general
safety and accident prevention regulations, the requirements of DIN VDE 0100, and the rules of the environmental protection of the country of use are respected and
adhered to.
The operator is responsible for ensuring that all work is
carried out with the product by trained, safety instructed
and authorized personnel.
The operator of the product or the personnel authorized
by him is ultimately responsible for the accident-free
operation.
The operator is responsible for compliance with the technical specifications, particularly for the observance of the
static and dynamic loads.
Ignoring the static loads can lead to loss of support
or hold function.
In terms of intended use of the operator environmentrelated (building side) has to provide a dry, not too hot
environment under the influence of radiant heat. Variances must be agreed with the manufacturer.
3.5
Safety instructions for technical condition
Requirements for the personnel
Any person who is assigned to work with the product
must have read and understood the entire manual before
performing the relevant work. This is true even if the person has already worked with such product or has been
trained for it.
© elero GmbH
Safety instructions for transport,
assembly, installation
The respective transport company is responsible for transportation of the product. The following safety requirements
must be observed during transportation, assembly and
installation of the product:
When transporting the product is to be secured in accordance with the provisions of the transportation aid used.
Only hoists and slings must be used for for transportation, which are dimensioned so that they can take safe
loading, unloading and installing of the product occurring
forces.
As a stop-and lifting points only defined for the points on
the pallet and the product may be used.
Are working under the raised parts or equipment required, they must be secured with suitable devices to prevent falling. Work equipment for lifting loads must prevent
the load from accidentally shifting or dropping in free fall
or being hooked unattended.
Staying under suspended loads is prohibited.
A protective helmet should be worn during loading and
unloading with suitable lifting gear.
Assembly and installation work must always be performed only by qualified and trained personnel.
The rated torque and rated duration must be compatible
with the characteristics of the driven member ("Hanging").
EN | 3
Product description
►The use of rigid shaft connectors and plugs stop or angle
strips or covert attacks is a prerequisite.
With the RolTop/D+ Type M is the smallest inner pipe
diameter for the winding shaft 47 mm.
►The height of the curtain is adjusted so that the push-up
protection operates correctly.
Access to the drive must be possible through a freely
accessible and always with little effort to open access
panel, which should be sufficiently large.
3.8
►For this purpose observe the requirements of the roller
shutter manufacturer.
• The variant-dependent values of your RolTop/D+ M can
be removed from the type label.
Safety instructions for operation
The user of the product is required to satisfy themselves
prior to the first use of the safe and proper condition of
the product.
That is necessary also during the operation of the product
at regular time intervals which can be specified by the
operator.
3.9
Safety instructions for electrical installation
• The different versions of the RolTop/D+ M contain different types of brake systems depending on size and
torque. The result may yield different performance eg
regarding access to end positions.
5
All work on the electrical system of the plant may only
be used by qualified electricians in accordance with the
applicable rules and regulations of the trade association,
to be made in particular as per the requirements of DIN
VDE 0100. Furthermore, the national law of the country
of use are to be observed.
In case of defects, such as loose connections or defective or damaged cables to the system, the product must
not be put into operation.
Prior to inspection, assembly and disassembly, the system (roller shutter, roller blind) is disconnected from the
mains.
All electrical connections, safety devices, fuses, etc. must
be properly installed, connected and grounded.
The provided power connection must be designed as
specified in the wiring diagram (voltage, voltage level).
A line protection switch (circuit breaker) is sufficient to
separate the plant from the grid (and if only one phase
and zero is used).
If a fixed (permanently installed) drive is not equipped
with a power cord with a plug or with other means for disconnection from the mains, which at each pole a contact
opening under the conditions of overvoltage category
III (according to IEC 60664-1) for full separation, as a
disconnecting device must be installed in the fixed wiring
according to the regulations.
The mains connection cable for drives with a rubber
hose, (abbreviation 60245 IEC 53) may be replaced only
with the same line type.
For drives where after installation the access to unprotected moving parts is possible, the following applies:
Moving parts of the drive must be mounted more than 2.5
meters above the ground (or any other level which provides access to the drive).
4
CAUTION
Personal injury from hot surfaces.
Drive heats up during operation, the drive housing can be
hot. Possible burning of the skin.
►Wear personal protective equipment (gloves).
Triggered by a possible material errors may occur or
impact shock and injury due to a gearbox break, bud break
or a clutch defect.
►Suitable materials are to be used for the construction as
well as perform a sampling inspection by double load test
according to DIN EN 60335-2-97.
Risk of injury due to impact or shock caused by not properly
mounted or latched motor bearings. Hazards caused by
insufficient stability or stability and stored energy (gravity).
►Selection of engine bearing torque specifications.
►Drive must be backed up with all attached backup devices.
►Check for proper latching on engine mounts and correct
tightening torques.
WARNING
Danger of injury due to electric current.
Electric shock possible.
►Electrical work can only be performed by an authorized
electrician.
Danger of injury due to electric current.
Hazardous possibly by parts that have become live in the
error state.
►Electrical connection is described in the operating and
installation instructions included cable bushing.
CAUTION
Product description
Risk of injury due to malfunctions due to improper installation.
The RolTop/D+ M is an electromechanical tubular motor
drive. It performs parallel axial movements.
Drive over-winds and possibly destroys parts of application.
Elero cable assembly is not required to start up the RolTop/D+ M. The elero assembly cable serves if necessary
only for the deletion of the end positions and/or for restoring the delivery status..
Sunblind with free ride
The RolTop/D+ M requires top and bottom fixed anchor
points. This is how an Automatic recognition and learning
of the end positions (self-learning) works.
Automatic correction of the final position, for example by
installing a window sill.
4 | EN
Assembly
© elero GmbH
►For a safe operation, the end positions must be set /
programmed.
►Training program of the manufacturer for specialists.
Note
Loss of power supply, termination of machine parts and
other malfunctions.
►For safe operation, no false mount must be made and the
end position settings must be carried out during commissioning.
Damage to the RolTop/D+ M due to moisture penetration.
Assembly: Mechanical fastening
►For devices with protection class IP44, the ends of all
cables or connectors must be protected against the
ingress of moisture. This measure must be implemented
immediately after removal of the RolTop/D+ M from the
original packaging.
Installation in profile tubes
Ⓐ Insert the drive with a suitable adapter and traction ring into the profile
tube.
Lay the motor cable protected in order to prevent damage by the driven
component.
►The drive may only be installed so that it is not irrigated.
Important
Ⓑ Secure the counter bearings against
axial displacement, e.g. screw shaft
spider or rivet.
Secure drive in axial storage!
In the delivery status (factory setting), the RolTop/D+ M in
commissioning mode.
►After successful mounting the drive must be driven altogether 3 times into the upper and 3 times into the lower
end position. The drive must be switched off each time
automatically.
• Programming the end positions is not subject to mandatory pattern, i.e. first, the upper end position, and then the
lower end position can be activated, or vice versa. Also
an alternate training of the end positions is possible.
Ⓒ Secure hanging on the shaft!
5.2
• During the learning phase, the drive moves with reduced
torque in the end positions.
If the entire learning process is complete,
• the drive moves at reduced speed into the end positions
(except RolTop/D+ M30).
• relieved the drive at the end positions.
The sunblind is adjusted only after a complete and uninterrupted access and exit to the blind.
Mechanical fastening
Important preliminary consideration:
The working space around the built-in drive is usually very
small. Therefore, before the mechanical installation provide
an overview of the implementation of the electrical connection (see Section 5.2) and take any necessary.
Note
WARNING
Danger to life due to faulty electrical connection.
Electric shock possible.
►Before commissioning check the correct connection of
the PE conductor.
NOTE
Damage to the RolTop/D+ M by faulty electrical connection.
►Before commissioning check the correct connection of
the PE conductor.
Damage or destruction of RolTop/D+ M by the penetration
of moisture.
►For units with protection class IP 44, the customer connection of the cable ends or connector (cable bushing)
must also be carried out in accordance with protection
class IP 44.
Damage or destruction of RolTop/D+ M for variants with
230 V AC 1 due to faulty control.
►Switch with OFF setting (Dead man) for drives must be
installed within sight of the RolTop/D+ M, but away from
any moving parts and amounting to about 1.5 m.
Damage to the electrical wiring by squeezing or tensile
loading.
►Route all electrical cables so that they are not subjected
to crushing or tensile load.
►Note the bending radius of the cables (at least 50 mm).
►Lay the connection cable in a loop downwards to prevent
water running into the drive.
Damage to the drive by the action of impact forces.
►Insert the drive into the shaft, never thrust the drive into
the shaft or smash onto the drive!
►Never allow the drive to fall!
Damage or destruction of the drive by drilling.
Important
For electric connection no transmission and retransmission
of the access line or connector is required as a rule.
Depending upon used mounting plate and/or adapter plate
it is necessary in particular with the RolTop/D+ M to remove
this screwed plate before a cable exchange.
Connection only in free of tension status, in addition
drive line without tension
1 Using a suitable screwdriver, press out the lock of the
device connector to the line.
►Never drill into the drive!
2 Disconnect the plug.
Important
3 Insert connector until the latch engages.
Attach the RolTop/D+ M only at the appropriate fasteners.
Removal and insertion of the device plug
Permanently installed control devices shall be clearly displayed.
Delivery status
• The profile tube must have enough distance to the motor
tube.
2
Insert plug
1
→
• The curtain must be fastened to the winding shaft.
Remove plug
→
5.1
Electrical connection
3
→
Fig. 4 Removal and insertion of the device plug
• Look for an axial clearance (1-2 mm).
© elero GmbH
EN | 5
Assembly: Electrical connection | Programming the end positions
5.3
Connection example RolTop/D+ M
230V / 50Hz
%OXH QHXWUDOFRQGXFWRU %ODFN %URZQ *UHHQ\HOORZ
(3)
Fig. 6Brown
Connection
for cable assembly
Green-yellow
brown
black
Blue (neutral conductor) (1)
Black (2)
blue
braun
green/Yellow
M
1~
Program end positions manually
junction box
1
102
102
The drive switches off when reaching the end stop automatically.
power grid
230V/50Hz
PE
N
L
3
2
1
Fig. 5
3
2
1
2
Press the [DOWN ▼] button till the shutter is shut
down up to 30 cm.
3
Repeat 2 more times, start of the upper stop (as
described in (1)).
4
Press the [DOWN ▼] button.
Proceed to the lower stop.
The drive switches off when reaching the end stop automatically.
Circuit diagram RolTop/D+ M 230 V / 50 Hz and
M
wiring with delivery
with Hirschmann plug STAS 3
1~
Important
5
Press the [UP ▲] button until the roller shutter is
ascended about 30 cm.
6
Repeat 2 more times, start of the lower stop (as
described in (4)).
marrone
The programming of the end positions is completed.
Important
After successful drive assembly the drive must be driven altogether 3 times into the upper end position and 3 times into
the lower end position. The drive must stop automatically.
nero
Parallel connection
blu
brun
verde/giallo
The motor control must be interlocked in up / down direction.
5.4
scatola di
Youderivatione
can connect several parallel RolTop/D+ M. Note the
maximum switching capacity of switching.
102
5.5
Commissioning
Important
5.5.3 Changing / deleting the limit positions and
deleting the discharge function
102
Therete
drive is in the delivery in commissioning mode.
5.5.1
230V/50Hz
Automatic
programming of end limits
PE
N
►The
L programming is done in the light of the end posi-
tions in Chapter 4 (product description) described prerequisites normally automatic (self-learning, without elero
cable assembly).
Program end positions automatically
1
Connecting the electrical system in accordance with
Chapter 5.2.
2
Check operation: If necessary, replace or modify
map the directional controls of the operation switch /
tasters.
The drive switches off when reaching the (upper or lower)
end stop automatically.
The teaching is completed by further movements of the
blinds.
5.5.2 Manual setting of the end positions
►The connection of the elero cable assembly is only permitted for manual operation of the drive and delete the
end positions.
6 | EN
Press the [UP ▲] button.
Move to the upper stop.
© elero GmbH
A change or deletion of a single end position is not possible.
This is always done in pairs (upper and lower end position
simultaneously).
By the deletion of the end positions and the adjustment of
the optional discharge function is lost.
Changing / Deleting the end positions
1
Connect the drive to the cable assembly and switch
on the power supply.
2
Adjust the shutter with the cable assembly in a central position.
3
Simultaneously press both the [UP ▲] and the
[DOWN ▼] buttons at the installation cables.
The drive runs up and down briefly.
The deletion of the setting of end position is completed.
The end positions can be programmed again.
Troubleshooting | EC Declaration of Conformity
9
Changing / deleting the limit positions
Method 2 only for types RolTop/D+ M
1
Move the blind with built-in drive to a centre position.
Move both direction buttons to the OFF position and
wait 3 seconds.
2
Press the [UP ▲] button 5 times in quick succession;
wait for the blind to move briefly in between.
3
Press the [DOWN ▼] button 5 times in quick succession; wait for the blind to move briefly in between.
Press and hold for at least 1 second on the fifth time
and there is no reaction.
After installing the drive, the R+S mechatronics technician
(roller shutter and sun protection mechatronics technician)
must note the installed type of drive and the installation
location in the installation and operating instructions.
Drive designation
The deletion of the end position setting is complete.
The end positions can be programmed again.
5.6
_________________________
____________________
_________________________
elero GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlierbach
Deutschland / Germany
Problem /
Error
Possible
cause
Cure
Remedy
• Drive does not
learn any end
positions
• Drive has
already been
programmed to
end position
• Move shutter
to the central
position, bring
the drive to
end position
deletion in the
delivery status
• Sluggish shutter
• Check for ease
of hanging or
selection of the
drive
• Undersized
drive
• Drive not
responding
• No mains voltage
• Thermostat
has tripped
• Check mains
voltage
• Allow drive to
cool
• Drive starts
only in one
direction
• Connection
error
• Check connection
• Drive does not
stop due to
obstacle
• Drive has not
saved any cutoff values
• Drive must be
moved from
end stop to
end stop at
least 2 times
without stopping
Fig. 7 Error search at the RolTop/D+ M
Phone: +49 7021 9539-0
Fax:
+49 7021 9539-212
[email protected]
www.elero.com
Should you require a point of contact for outside of Germany, please visit our website.
10
Disposal / scrapping
Dispose of the packaging according to current regulations.
Dispose the product after previous use in accordance with
applicable regulations.
Scrapping
During the scrapping of the product, the international,
national and regional-specific laws and regulations are to be
complied with.
Please make sure to consider material recyclability, ease of
dismantling, and separability of materials and components
as well as environmental and health hazards during recycling and disposal.
Groups of materials such as plastics and metals of various
kinds are sorted for recycling and disposal process.
Dispose electrical and electronic components
Disposal and recycling of electric and electronic components must comply with the applicable national laws and
regulations.
11
EC Declaration of Conformity
elero GmbH hereby declares that this product corresponds
to the applicable directives. The complete declaration of
conformity can be found under
www.elero.com/downloads-service/
Repair
The RolTop/D+ M is maintenance free.
8
____________________
If malfunctions occur despite proper handling or if the unit
has been damaged, contact your contract partner.
Troubleshooting
• Drive stops
after a short
ride
7
____________________
Installation location
(e.g. living room window 2)
_________________________
Specifications
A summary of the main technical parameters, see the separate overview "Technical Specifications".
6
Service/manufacturer‘s address
12
Repair
If you have any questions, please refer to your specialised
company. Please always state the following information:
• Item number and item designation on the nameplate
Technical data and dimensions
The technical data specified is subject to tolerance factors
(according to applicable standards) and refer to an ambient
temperature of 20 °C.
• Error type
• Previous and unusual events
• Surrounding circumstances
• Own assumption
© elero GmbH
EN | 7
C
Type
E [Nm]
Rated torque
55
12.1 RolTop/D+
O 45
D
/D+ S5
/D+ S8
/D+ S12
5
8
12
33
/D+ M6
/D+ M10
/D+ M20
/D+ M30
6
10
20
30
Rated speed [1/min]
17
17
17
14
14
14
14
Rated voltage [V]
1 ~ 230
1 ~ 230
1 ~ 230
1 ~ 230
230 - 240
1 ~ 230
1 ~ 230
50
50
50
50
50
50
50
■
-
■
■
■
-
Rated frequency [Hz]
C■
Rated current [A]
0.55
0.55
0.73
0.52
0.60
0.90
0.90
130
130
168
118
140
200
200
Shaft diameter [mm]
38
38
38
50
50
50
50
Degree of protection (IP-Code)
44
44
44
44
44
44
44
40
40
40
40
40
40
40
Operating time (min S2)
5
4
4
4
5
4
4
Length C [mm]
534
534
534
446
466
526
516
Length D [mm]
517
517
517
429
449
509
499
- | 12 | -
- | 12 | -
- | 12 | -
- | 14 | 19
- | 14 | 19
- | 14 | 19
- | 14 | 19
D
E
Length E [mm]
(elero head, round head, star head)
1,3
1,3
1,3
1,6
1,9
1,9
1,9
-20 to 60
C
-20 to 60
-20 to 60
-20 to 60
-20 to 60
-20 to 60
-20 to 60
D ■
■
■
■
■
■
■, ■
■, ■
■, ■
■, ■
■, ■
■, ■
2.0
2.0
2.0
2.0
2.0
Weight [kg]
Ambient operating temperature [°C]
Protection class I
,
Plug-in connecting cable [m]
Article-no. (elero head
SH star head)
O 45
Conformity
33
30 237.0001 30 257.0001 30 817.0001
E
29
■
■, ■
O 49,5
Limit switch range (revolutions)
O 45
Rated power consumption [W]
55
Noiseless soft brake
2.0
2.0
34 013.0002 34 023.0002 34 033.0002 34 043.0002
39 013.0002 39 023.0002 39 033.0002 39 043.0002
33
C
C
D
55 O 49,5
O 45O 45
D
E
E
33
33
CC
OO4545
O5557,5
DD
33
33
EE
C
elero GmbH
Antriebstechnik
Maybachstr. 30
73278 Schlierbach
DC
D
[email protected]
www.elero.com
29
Subject to technical changes
">
