- No category
advertisement
Bronze
Circulator Pump
Inline Centrifugal
Circulator Pumps
• Cast Iron or Silicon Bronze
Construction
• EPDM/EPR Mechanical Seal and Casing O-ring, Buna-N
Option Available
• Investment Cast Stainless Steel
Impeller with 569/570/571
Series, 572 Series Includes
Silicon Bronze Impeller
• Accessory Mounting Flanges
Available 3/4˝ to 2˝ NPT
• Maximum Temperature 225° F
(107º C)*
• Maximum Flow 58 GPM
• Maximum Head 19 Ft. (8 PSI)
• Single Phase 1/4 HP, 1725 RPM,
115 VAC ODP 56J Motor with
Overload Protection
AMT Inline Circulator Pumps are designed for continuous duty industrial/ commercial systems. Pumps are available in a variety of material configurations to meet your specifications. All models are powered by a single phase 115 VAC ODP 56J NEMA frame 1/4 HP electric motor with 1/2-14
NPSM conduit connection. Direct coupled design eliminates stub shaft, oiled bearing and coupling, reducing maintenance.
Pumps are interchangeable with other manufacturers, see cross reference on specification page.
* Maximum temperature applies to water only.
[ m ] [ f t .
* ]
2 0
4
1 8
1 6
3
2
1
1 4
1 2
1 0
8
6
4
2
0
Performance of Inline Circulator Pumps
A
B a s e d o n M a x i m u m F l a n g e S i z e
A = 5 6 9 S e r i e s 1 / 4 H P [ 0 .
1 9 k W ]
B = 5 7 0 S e r i e s 1 / 4 H P [ 0 .
1 9 k W ]
C
D
= 5 7
= 5 7
1 S e r i e
2 S e r i e s 1 / 4 H P [ 0 .
1 9 s 1 / 4 H P [ 0 .
1 9 k W ] k W ]
B
C
D
0
0
0
5 1 0 1 5 2 0 2 5 3 0 3 5 4 0 4 5 5 0 5 5 6 0
[ U .
S .
g p m ]
2 4 6 8 1 0 1 2 1 4 1 6
C a p a c i t y @ 1 7 2 5 R P M ( 6 0 H z )
( * ) C o n v e r t t o p s i , d i v i d e b y 2 .
3 1 L i q u i d W a t e r s p e c i f i c g r a v i t y 1 .
0
1 8 [ m 3 / h ]
A Gorman-Rupp Company
® 400 Spring Street • Royersford, PA 19468 USA
www.amtpump.com
• 888-amt-pump (268-7867)
For use with nonflammable liquids compatible with pump component materials. Viton ® and Teflon ® are registered trademarks of E. I. Dupont.
HVM-7
A Gorman-Rupp Company
®
Inline Centrifugal Circulator Pumps
Pump Dimensional & Specification Data
Model
5690
5700
5710
5720
‡ Curve
A
B
C
D
HP
1/4
PH ENC
1 ODP
Voltage
@ 60 Hz
115
Full Load
Amps
5.4
**This dimension may vary due to motor manufacturer specifications
NOTE: Dimensions are in inches (centimeters) and have a tolerance of ± 1/8".
NOTE: Electric supply for ALL motors must be within ± 10% of
nameplate voltage rating (e.g. 230V ± 10% = 207 to 253.)
569/570/571 Series – Stainless Steel Impeller
572 series – Bronze Impeller
A B C W H**
2.1 [5.3] 3.1 [7.9] 3.1 [7.9] 6.3 [16.0] 13.3 [33.8]
2.3 [5.8] 3.4 [8.6] 3.4 [8.6] 8.5 [21.6] 13.5 [34.3]
2.3 [5.8] 3.4 [8.6] 3.4 [8.6] 8.5 [21.6] 13.5 [34.3]
2.3 [5.8] 3.4 [8.6] 3.4 [8.6] 8.5 [21.6] 13.5 [34.3]
‡ Ship Wt.
(Lbs.)
25
28
28
28
‡ When ordering add the correct -9x suffix to model number indicating material selection
XCI (-95) = Cast Iron Construction
XB (-97) = Cast Bronze Construction
PUMPS ARE
DESIGNED TO MOUNT
HORIZONTALLY
OR VERTICALLY
W Dimension Refers to Flange to Flange Width
Connection Flanges - Flange Kit Model Numbers
Flanges Available - Standard NPT (Female) Pipe Thread
Model Series
569 Series XCI
569 Series XB
570 & 571 series XCI
570 & 571 series XB
572 Series XCI (-95)
572 Series XCI (-97)
3/4''
C569-90
C569-93
C570-90
C570-94
N/A
N/A
1'' 1-1/4''
C569-91 C569-92
C569-94 C569-95
C570-91 C570-92
C570-95 C570-96
N/A N/A
N/A N/A
NOTE: NPT Flange Kits Include:2 Flanges, 2 Buna-N Gaskets, 4 Bolts and Nuts
1-1/2''
N/A
N/A
C570-93
C570-97
N/A
N/A
2''
N/A
N/A
N/A
N/A
C570-98
C570-99
Flange Face to NPT
Face Thickness
3/4''
3/4''
3/4''
3/4''
1-1/2''
1-1/2''
Standard Features
• 4-Bolt Flange Allows 360° Mounting Rotation in 90° Increments
• 1/8'' NPT Seal Wash/Vent Port Shipped Plugged
• EPDM/EPR Mechanical Seals and O-Rings
• Optional Buna-N Mechanical Seal and
O-Ring Available
• Close Coupled Design Reduces
Maintenance Requirements
• Standard NEMA 56J Motor
Mounting Dimensions
• Stainless Steel (300 Series) Motor Shaft
• High Efficiency Closed Impeller
• Inline Centered Design, Centerline of Ports In Line with Motor Shaft
• Maximum Working Pressure 150 PSI
• QSP: Quick Ship Pump for Many Models
Manufacturer Cross Reference
Model
Series
569
570
571
572
Flange to Bell & Gossett Armstrong TACO Dayton
Flange Width* Series Series Series (Cast Iron)
6.4
100NFI S-25 110 4RD16
8.5
8.5
8.5
HV NFI
PR
2NFI
H-32
H-41
S-35
111
113
120
4RC93
4RC91
4RC95
*Refers to B Dimensions
A Gorman-Rupp Company
®
Manufacturer of AMT & IPT Pumps
400 Spring Street • Royersford, PA 19468 USA www.amtpump.com
• 888-amt-pump (268-7867)
The Gorman-Rupp Company reserves the right to discontinue any model or change specifications at any time without incurring any obligation.
©2012 American Machine and Tool Company. All rights reserved.
1212
HVM-8
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement